U se r G u id e Ioline FlexJet E & StudioJet Printers
User Notice Trademarks Ioline, StudioJet and FlexJet E printers are trademarks of Ioline Corporation. HP is a trademark of the Hewlett-Packard Company. Other product names, logos, designs, titles, words or phrases mentioned within this publication may be trademarks, service marks, or trade names of Ioline Corporation or other entities and may be registered in certain jurisdictions including internationally.
Ioline FlexJet E Printers User Gu i d e
Table of Contents Safety & Cautions Visual Reference Guide Chapter 1 Overview Chapter 2 Installation Chapter 3 Operation Getting Started ................................................................................................. 15 How The Ioline FlexJet E and StudioJet printers Work ................................. 16 Printer Assembly ............................................................................................... Unpacking the Printer .........................................
Control Center Menu Bar Features ................................................................ 27 File ............................................................................................................................................ 27 Communications ................................................................................................................... 27 Tools ..........................................................................................................................
Cartridge Maintenance and Handling ............................................................. Check Cartridges .................................................................................................................. Automatic Cleaning Procedure ......................................................................................... Manual Cleaning Procedure ................................................................................................ Print Cartridge Storage . ...............
NOTES
NOTES
Safety & Cautions The Ioline FlexJet E and StudioJet printers have many fast moving components. Please read and follow these safety guidelines before beginning operation of the printer: n Do not try to repair the machine without factory authorization. Only qualified service personnel should attempt any disassembly or access to internal components. If external mechanical adjustments are necessary, turn off the printer and disconnect it from all power sources (both the computer and the wall outlet).
Visual Reference Guide KEY A. B. C. D. E. F. G. Feed Shaft H. Dancer Bar I. Stand AA. Power Switch BB. Serial Port CC. USB Port Left End Cover Right End Cover Take-up Motor Stand Leveling Foot Feed Roll Take-up Shaft Rear Panel Behind Right End Cover A AA BB CC B F C H I G E D x The Ioline FlexJet E Printer Front View.
Visual Reference Guide KEY J. K. L. M. N. P. Q. R. S. T. U.
Visual Reference Guide KEY A. B. C. D. E. F. G. H. I. J. Left End Cover Drive Shaft Marker Pinchwheel Lever Pinchwheel Drive Shaft A B K. L. M. N. O. Right End Cover Keypad Stand Leg Inkjet Cartridge Carriage Stand Leveling Foot Feed Shaft Cross-member Platen Traverse F C D E G O H N M L K E Figure 5. The Ioline StudioJet Front View.
Chapter 1 Overview Unless otherwise noted, diagrams and descriptions depicting Ioline FlexJet E printer models also apply to the Ioline StudioJet in this manual. Getting Started Thank you for purchasing the Ioline FlexJet E or StudioJet printer. This manual contains instructions and guidelines for setting up, operating and maintaining your Ioline printer.
Ioline FlexJet E User Guide 16 How The Ioline FlexJet E and StudioJet printers Work The FlexJet E and StudioJet printers create printed images through synchronized media and carriage motion. Files are sent to the printer from a computer or file server via a serial or USB* connection. When the printer receives a file, the electronic logic system translates the vector image into X-axis (paper motion) and Y-axis (carriage motion) instructions and uses digital feedback to ensure plot accuracy.
Chapter 2 Installation An overview of the complete setup procedure is described in detail in the FlexJet E Printer and StudioJet Quick Start Guides (provided in the Accessory Kit). Printer Assembly Unpacking the Printer Carefully remove the printer from the box and place it on a flat, stable surface. This procedure requires two people. Check the packing list to ensure that all of the accessories are present. (See the FlexJet E printer or StudioJet Quick Start Guide for more information.
18 Ioline FlexJet E User Guide Cable Connections When connecting the printer to the computer by serial cable: 1. Make sure that power to the printer is off. Power is off when the switch is in the “0” position, and is turned on when placed in the “1” position. 2. Connect the supplied serial cable and power cord to the panel on the back right end cover of the printer. Lock the serial cable to the port on the printer with the thumb screws. COM Ports Figure 8.
Chapter 2: Installation 19 Figure 10. FlexPlot Serial Port set-up window. Baud Rate The serial port on the printer has an adjustable baud rate. Available speeds are 9600, 19200, 38400, 57600, and 115200. The default is set at the factory to 38,400. The baud rate is adjustable in the Control Center in the Communications>Settings window. Other Serial Port Settings You may also need to set additional serial port settings, for instance, when you use a terminal program.
20 Ioline FlexJet E User Guide CAD Software HPGL DM/PL FlexJet E printer Figure 11. Workflow: output direct from CAD software (without FlexPlot). 2. Use FlexPlot software to convert files before sending them to the printer for output. The printer includes the FlexPlot software which will convert many different files into a format that is compatible with the printer. It also provides an advanced marker queue management system and other tools to optimize the performance of the printer.
Chapter 2: Installation 21 Power On Turn on the computer and the printer to make sure they both work. The printer power switch is located next to the power cord on the back of the machine, behind the keypad. When the paper is properly loaded and the printer is powered up, the carriage will move toward the left side of the machine, then return to the opposite side to park in the Service Station.
22 Ioline FlexJet E User Guide This page intentionally left blank
Chapter 3 Operation Keypad Controls The keypad provides access to the main functions of the printer. Figure 13. The Printer Keypad. Start/Stop The Start/Stop key toggles the printer online and offline. If the Start/ Stop key is pressed during printing, the OK light turns red and the machine will stop after it finishes printing the current scan. The Arrow, Unroll and Paper Advance keys are active when in STOP mode.
24 Ioline FlexJet E User Guide Clean Runs the print heads through a cleaning cycle in the Service Station. Put the printer in STOP mode and wait until the OK light turns red. Then press the Clean button. If the carriage is not already parked, it will return to the Service Station. After auto cleaning, the printer will react differently when you put it in green light (START) mode, depending on what it was doing just prior to the cleaning: Printer state before auto cleaning—e.g.
Chapter 3: Operation 25 Arrow Keys Pressing the Arrow keys moves the carriage left or right. The Arrow keys are only active in STOP mode (see Start/Stop), when the OK light is red. Page Advance Pressing this button advances the paper in small increments. This is useful if a plot was removed from the printer and you need a paper leader to tape to the take-up shaft. The Page Advance key is only active in STOP mode (when the OK light is red).
26 Ioline FlexJet E User Guide i Note To avoid communication port conflicts, do not simultaneously run more than one application that communicates with the printer. The Control Center Overview The Control Center is a utility program that does two things: n Allows you to adjust settings to tailor output (e.g. scale, line width) from the computer. n Provides an interface to send completed files to the printer. Figure 15. Control Center Main Menu.
Chapter 3: Operation 27 Control Center Menu Bar Features File Send Plot File Print a PLT or PLX file. Download Firmware Allows the user to download the latest firmware version for the printer. See the section Downloading Firmware in the Routine Maintenance chapter for more information. Exit Exit the Control Center. Communications Settings Select the COM port and baud rate to match the printer. Send Command Permits advanced users to manually enter commands.
28 Ioline FlexJet E User Guide Control Center Menu Options Firmware Version and Base Displays the current firmware version installed in the printer. Enabled Heads Displays how many cartridges are in active use by the printer. Get Plotter Data Reads and displays the current settings stored in the printer. Plotter Data (check box) Indicates when the displayed settings were successfully downloaded from the printer.
Chapter 3: Operation 29 X-axis (paper direction) frame size is 46-in (116.8-cm), maximum is 21600-in (54,864-cm). Default and maximum Y-axis (carriage direction) frame size is 72-in (182.9-cm). Quality Setting Choose Draft or Best to control line density. Draft mode uses 300 DPI. Best mode uses 600 DPI. A lower DPI setting uses less ink by creating a fainter line. Higher DPI uses more ink but makes a darker line.
Ioline FlexJet E User Guide 30 Figure 17. Insert ink cartridge at an angle into the cartridge bay. Lock in place with the stall latch. 3. Insert the new cartridge with the print head pointing down toward the rear of the stall and at a slight outward angle. Press firmly while rotating the top of cartridge toward the back of the stall until it stops in an upright position. (See Figure 17.) 4. Close the stall latch.
Chapter 3: Operation 31 Loading Paper on the StudioJet Caution Keep hands and loose clothing away from all moving parts. See the StudioJet Quick Start Guide. Loading Paper on the FlexJet E 1. Before loading a new paper roll always make sure the drive shaft is clean. See the Routine Maintenance section for more details. 2. Place a paper hub in each end of the paper roll using a rubber mallet. 3. Slide the feed shaft through the paper hubs and the paper roll.
32 Ioline FlexJet E User Guide Caution Never touch the take-up key or flanged coupling while they are rotating. Serious personal injury could result. Turn power off first. Installing the Take-up Shaft (FlexJet E only) The Paper Out sensor on the back of the printer detects when the paper runs out. If paper isn’t loaded or if the take-up key is not positioned properly, place a small piece of masking tape over the Paper Out sensor before following the steps below.
Chapter 3: Operation 33 take-up shaft into place until it is seated in the support block. Feeding Paper (FlexJet E only) Figure 20 represents the proper paper path. The left side of the diagram shows the paper path for a 1H FlexJet E. The right side shows the proper path for a FlexJet E with 2 or more heads. 1. Remove any printed markers from the take-up shaft and make sure the carriage is parked in the Service Station before feeding the paper. (To park the carriage, press Start/Stop.
34 Ioline FlexJet E User Guide i Note When installing or retaping paper, remove the front dancer bar and set it aside. Tape Paper to the Take-up Shaft 1. Stand in front of the machine. 2. Place 3 short pieces of masking tape within easy reach on the top cover. (See Figure 21.) 3. Holding the edge of the paper with one hand, use your free hand to lower the pinchwheel lever to raise the pinchwheels. 4.
Chapter 3: Operation 35 i Note Ensure that the paper roll is centered on the feed shaft. Pinchwheel White Driveshaft Markers Drive Shaft Segment Figure 22. Positioning the pinchwheels. Drive Shaft Bearing 3. Make sure that the paper roll is tight on the feed shaft. 4. Move the pinchwheels into their proper positions over a tread and under the white markers on the traverse rail. (See Figure 22.) Do not place pinchwheels over drive shaft bearings.) 5. Lower the pinchwheels.
Ioline FlexJet E User Guide 36 Insert Rear Dancer Bar (2H+ FJE Models Only) 1. FJE models with two or more printheads and the high speed printing kit require that a heavy dancer bar is inserted in the rear dancer bar channel (see paper path in Feeding Paper). 2. Take the heavy dancer bar (painted black on some models) and insert the ends into the notches in the stand legs on the back of the machine as shown in the image below. 3.
Chapter 3: Operation 37 Canceling a Marker Plot 1. Press the Start/Stop key to place the printer in STOP mode (red light). The printer will finish printing the current scan and pause. 2. To stop the computer from sending plot files to the printer, click the Abort button in FlexPlot. 3. Use the keypad Arrow keys to position the carriage for the start of a new plot file as described earlier. 4. Press the Set Origin key to ready the printer for the next plot file.
38 Ioline FlexJet E User Guide Manually Freeing the Take-up Shaft (FlexJet E Only) Use this method to remove the take-up shaft from the completed roll without having to unroll the markers. 1. Tape the loose end of the roll down so that it cannot flap freely. 2. Rotate the take-up shaft by hand until the rectangular opening in the flanged coupling is perpendicular to the opening in the support block (see Figure 19). Remove the shaft. 3. Stand the roll on end with the flanged coupling pointing up.
Chapter 3: Operation 39 Automatically Freeing the Take-Up Shaft (FlexJet E Only) Like the manual method, this method removes the take-up shaft from the completed roll without having to unroll the markers. The only difference is the use of the take-up motor. 1. Tape the loose end of the roll down so that it cannot flap free. 2.
40 Ioline FlexJet E User Guide Caution If the paper bubbles or wrinkles while it flows over the platen surface, the carriage might catch the edge of the paper and tear it, causing a paper jam. Make sure that the paper is smoothly collecting on the floor to avoid paper jams. i Note The front dancer bar should not be used when plotting to the floor. Printing to the Floor With careful setup and constant supervision, the printer will print markers directly onto the floor.
Chapter 4 Routine Maintenance Cleaning the Drive Shaft Do not pray the printer with water, solvents or other liquids. Use a nonmetal bristle brush or a cloth dampened with water or isopropyl alcohol. Keep the drive shaft bearings free of all liquids. Clean the drive shaft regularly to assure accurate plotting: 1. Turn off the printer and disconnect the power cord. 2. Gently remove any accumulated dust and residue with the stiff nonmetal bristle brush provided in the Accessory Kit. Caution Figure 27.
42 Ioline FlexJet E User Guide Caution Never touch the take-up key or flanged coupling while they are rotating. Serious personal injury could result. Turn power off first. Cleaning the Support Blocks (FlexJet E Only) When dust and paper residue will accumulate on the take-up and feed shaft support blocks, frequent feed shaft jams can occur. Perform this procedure when debris inhibits easy rotation of the shaft. 1. Turn off power to the printer. 2. Remove the feed shaft and the take-up shaft. 3.
Chapter 4: Routine Maintenance 43 Use the Control Center to Gather the Calibration Data 1. Open the Control Center program. 2. Select Tools>Size Calibration from the Menu Bar. The window in Figure 30 will appear: 3. Press the Send Size Plot button to print the factory stored calibration box. The printer will print a box that is 40” (102-cm) long on the X-axis and 30-in (76-cm) wide on the Y-axis. i Note Only use Reset Calibration to restore original factory calibration settings.
44 Ioline FlexJet E User Guide i Note i Cartridge alignment is not necessary for models with a single activated cartridge stall. Cartridge Calibration There are three types of adjustments associated with the ink cartridges. Most line quality issues are resolved by adjusting these values. n Cartridge Alignment is not necessary on the FlexJet E and StudioJet printers. n Motion Adjustment aligns scans in the direction of carriage travel. n Frame Gap aligns scans in the direction of paper movement.
Chapter 4: Routine Maintenance 45 Motion Adjust (Carriage Scan Alignment) i Note 1. Press Select Alignment Plot. Adding (+) numbers moves the second scan left. 2. Browse to the c:\Ioline\Calibration folder. Select the 40X8.plt test file. Subtracting (-) moves the second scan right. 3. The Motion Adjust box has one number for adjustment. The default value is 0. 4. Changing the values affects the next scan, created when moving from left to right. 5.
46 Ioline FlexJet E User Guide Hint Use Best Mode when testing print quality as the higher resolution (600 dpi) setting exercises more nozzles and pushes more ink out of the cartridge. Cartridge Maintenance and Handling A key to maintaining good print quality is proper print cartridge maintenance. During printing, ink-spray, paper fibers and dust can build up on the print cartridge and eventually will degrade plot quality.
Chapter 4: Routine Maintenance 47 Manual Cleaning Procedure To maintain optimal print quality, manually clean cartridges after they sit idle for longer than two days—or are placed in storage. Wiping the print head will clean out the nozzles and firing chambers. A Cloth Should Be: n Soft, fiberless, and moistened with deionized water. Should NOT Be: n Abrasive, made of small fibers, dry nor contain chemical additives. 1. Press the Start/Stop key. 2.
48 Ioline FlexJet E User Guide Print Cartridge Storage Short-term Storage (7 days or less) n Simply leave the print cartridge in the machine, capped in the Service Station. n If the cartridge was not in the Service Station, it may require manual cleaning. Long-term Storage (greater than 7 days) n n lace the print cartridge upsidedown in an air-tight container. Lay a sponge or cloth dampened with de-ionized water next to it to help prevent the cartridge from drying out. Figure 34.
Chapter 4: Routine Maintenance 49 3. If you do not see a firmware version displayed, please check connections to the printer. Call Ioline Customer Service for help resolving communication issues. Update the Firmware 1. Choose File>Download Firmware from the menu bar. 2. Press the Select Firmware button. 3. Follow the on-screen directions for restarting the printer so that it will accept new firmware. Press OK when the printer is ready (three yellow lights on the keypad.) 4.
50 Ioline FlexJet E User Guide Reset Calibration Values Perform the steps below if calibration values have been altered: 1. With the printer in STOP mode, use the arrow keys to move the carriage to the center of the traverse. 2. Turn power off on the printer. 3. Copy the factory calibration values from the white sticker inside the service station (see Figure 35.) If no sticker is present, recalibrate the machine using the procedure available in this User Guide. 4.
Chapter 5 Troubleshooting General Troubleshooting If the printer is not working correctly the problem could arise from the computer, the cable, the design software or the printer. Changes to the computer operating system or the installation of new peripherals or software might cause conflicts. If the computer or the design software are causing a problem, consult your computer and/ or software manuals, or call your manufacturer or dealer.
52 Ioline FlexJet E User Guide Printing Quality Good printing quality is dependent upon a number of different factors. The type of paper, environmental conditions, and operator habits are only a few of the variables that can affect the quality of a plot. It is important that the printer is loaded and maintained according to the guidelines under the Operation chapter. If the scans (printing from a single pass) do not line up, see the sections on calibrating the printer in the Routine Maintenance chapter.
Chapter 5: Troubleshooting 53 3. Continue holding the Page Advance key until the OK light turns red and the Square light turns green. 4. Cycle power again (do not touch any keys this time) to ensure communications are reset. If using a terminal program like TeraTerm™ to communicate with the printer, make sure to use 8 Data Bits, No Parity, 1 Stop Bit, and Xon/ Xoff Flow Control.
54 Ioline FlexJet E User Guide Common Issues A marker plot doesn’t start at the correct point on the paper Cause: Solution: The origin is not set. Position the pen where the plot should start. Press the Set Origin key. The printer does not complete the marker. Cause: Solution: 1. Outdated software. 1. Visit the Ioline Web site to download upgrades. Or, contact Ioline Customer Service. 2. The frame/panel size is mismatched between the printer and the design software. 2.
Chapter 5: Troubleshooting 55 Jagged scan alignment. Cause: Solution: 1. Motion alignment is incorrect. 1. Use the Control Center to adjust motion alignment as shown in the Routine Maintenance chapter. 2. Platen or stand is not level. 2. 3. Loose carriage pulley causing random/uneven gaps between scans. Follow the directions in the FlexJet E Printer or StudioJet Quick Start Guide to level the stand and platen. 3. Contact Ioline customer service. Poor paper tracking. Cause: Solution: 1.
56 Ioline FlexJet E User Guide Regular or intermittent paper tearing. Cause: Solution: 1. Front dancer bar is not installed. (FlexJet E models only.) 1. Install front or rear dancer bar. 2. Paper gets “yanked” by the machine during take up. 2. Remove slack from paper roll before pressing Set Origin. 3. Paper is improperly loaded. 3. Reload paper and verify that it is in alignment. 4. Paper buckles when plotting to floor. 4. Clear paper path. 5. Paper roll damaged. 5.
Chapter 5: Troubleshooting 57 Common Issues (FlexJet E Models only) Take-up roll never rotates, paper loop is too long in front of machine. Cause: Solution: 1. Take-up motor is unplugged. 1. Plug in the take-up motor. 2. Dancer bar is below the lower sensor. 2. Roll paper up by pressing and holding the Unroll and Right Arrow key. 3. Lower sensor does not work. 3. Contact Ioline customer service. Take-up roll does not stop; paper is pulled tight in front of machine. Cause: Solution: 1.
58 Ioline FlexJet E User Guide This page intentionally left blank
Chapter 6 End Notes Service & Support Ioline has many years of experience working with designers, graders and marker makers. Feel free to contact us if you have questions—or to share information. Getting Help Ioline is committed to providing the highest quality service and support to its customers. If you need assistance with an Ioline FlexJet E or StudioJet printer, a number of resources are available: 1. First, refer to this User Guide for answers to your specific questions. 2.
60 Ioline FlexJet E User Guide prevent damage. Seal the container and note the RMA number near the address block. 3. Ship the container using FED-EX or another approved carrier. COD shipments ARE NOT ACCEPTED. An Ioline representative will contact you prior to the start of work with an estimate of repair cost. All repairs are warranted for 90 days. Customer Service Ioline Corporation is committed to providing quality service and support to our customers.
Chapter 6: End Notes 61 Before you contact Support… Please gather the following information about your printer before contacting Ioline or your dealer for technical support: Name: Company Name: Phone Number: Fax: E-mail: Model: Serial Number*: Date of purchase: Dealer: Type of media & ink used: Type of Computer: Type of design software: New software or peripherals: Service history: * You’ll find the serial number above the power switch on the back side of the right cover.
62 Ioline FlexJet E User Guide The FCC Wants You to Know... This equipment generates and uses radio frequency energy and, if not installed and used properly (in strict accordance with manufacturer instructions), it may cause interference to radio and television reception. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Glossary A F Acceleration – The rate that a printer changes the velocity of the carriage or the paper. Acceleration is measured in units of g (1 g = 32.2 ft/s2). Feed Loop – Slack material between the feed roll and the printer. Arc – A segment of a circle, also called a curve. Feed Shaft – Metal rod that holds the paper roll parallel to the printer and allows it to turn during feeding. Axis – A geometric guideline used to place a coordinate.
Ioline FlexJet E User Guide 64 K Roll Feed – A method of pulling material from a roll for printing. Keypad – Panel on the right side of the printer where the user controls simple printer functions. Carriage and paper motion is accessible from here during Stop mode. Also called the Control Panel. S M Scan – A single pass of the carriage over the platen. The printer may or may not print during a scan. Mil – Thousandths of an inch or milli-inches. For example; 75 mils is the same as .075 inches.
Glossary 65 Throughput – The speed at which a printer completes a job. Represents the ability to process information and produce an image. Traverse – Structure that supports and guides the carriage and holds the pinchwheel assemblies. U USB – Universal Serial Bus. High speed method for transferring information from a PC to a peripheral like a printer. V Vector – A line segment between two coordinates. X X-Axis – Theoretical horizontal line providing a length reference point for the printer.
66 Ioline FlexJet E User Guide This page intentionally left blank
Index Symbols 51645A 29 Cables Power cord 18, 21, 41, 54 Serial 17, 18, 48—See also Serial port Socket and port locations on FlexJet E 18 CAD software—See Design software Alignment—See Calibration; See Troubleshooting Calibration 27, 42–46, 49, 50 Cartridge calibration window in Control Center 44 Control Center calibration screen 42 Factory default settings 43, 50 Calibration sticker 50 Ink cartridges 44 Measuring the calibration box 43 Motion adjust box 45 Plot size 42 Arc 63 Calibration box 45 Arro
Ioline FlexJet E User Guide 68 Using the brush 41 Control panel 23, 63—See also Keypad Clipping 28 Conversion 15, 20 Communication Serial xiv Coordinate 63 Communications 64 Automatic Buffer Closing 27 Baud rate 18, 19, 25, 27, 28, 44, 52, 57 Data bits 19, 53 Flow control 19, 53 Parity 19, 53 Stop bits 19 Conflicts 26—See also Troubleshooting Get plotter data 28 Ports—See Serial port, USB Settings 27 COM ports—See Serial port, USB Computer 17, 61 Consumables 29 Ink 29—See also Ink cartridges Paper 2
Index 69 Feed roll x Feed shaft x, 30, 31, 35, 42, 55, 63, 64 Flanged coupling 31 Installing feed shaft 31 Support block 31 File conversion 15 Frame gap 44 Eliminating or adjusting 45 Frame gap box 45 Frame gap box 45 Frame size 28, 63 Friction feed 63 File formats 15, 19, 20, 63 File import 15 Files Download firmware 27, 49 File name extensions 63 EPS 27, 63 PLT 27, 63 PLX 27, 63 Plot file adjustments—See Control Center Send plot file 27 Firmware Software version 28 Updating 27, 48–50 FlexJet E Control
Ioline FlexJet E User Guide 70 Cartridges in stalls xii Ink 29 Ink level indicator 46, 47, 52, 56 Empty cartridge 52 Maintenance and handling 46–48 Requirements 29 Stalls xii, 29, 30 Storage 48 Air-tight container 48 Upgrading number of stalls 27 Installation 17–22 Ioline Corporation 60 M Maintenance 41–50 Lubricants 42 Manual unroll 25 Marker removal Manually freeing take-up shaft 38 Markers—See also Plot Removal 37–39—See also Unroll Using cardboard tube 37 Starting position—See Plot Set origin Measure
Index 71 Paper motion—See Plot Plotting quality—See Printing quality Paper Out sensor 21, 27, 32 Poor line quality—See Printing Quality; See Troubleshooting Paper path 33, 34, 40, 56 Correct feeding path 33 Feed loop 63 Printing to floor 40 Paper path diagram 40 Sensor 64 Reattaching paper after marker removal 39 Take-up Loop 64 Taping paper to take-up shaft 25, 34, 37 Port setup 18–19 Paper scan alignment 45—See also Frame gap Paper sensor 25, 56—See also Paper path Printing to floor Parity 19, 53 P
Ioline FlexJet E User Guide 72 Reset serial port baud rate 25 Set motion 45 Resolution 64—See also Printing resolution Set origin 24, 36, 37, 42, 44, 54, 56, 64 Marker on carriage 24 Button 24 Restore Factory Default Settings Button combination 25 Restore factory default settings 25 Right Arrow key 55 Size calibration 27, 42, 43 Software—See also Firmware Apparel design software 15, 17, 19, 24, 28, 36, 51, 52, 54, 57, 61, 63 Right end cover x Control Center 15, 17, 18, 19, 21, 26, 27, 28, 30, 43,
Index 73 Take-up motor cable xi Take-up motor outlet xi W Take-up sensor xii—See also Sensor White driveshaft marker 35 Take-up shaft x, 16, 25, 32, 33, 34, 36, 37, 38, 39, 40, 42, 64 Installation 32 Installing take-up shaft 32 Manually freeing take-up shaft 38 Maximum paper roll length 16 Windows 21, 63 Taping paper to take-up shaft 34 Tape positions 34 Tech Support 60 Wrench 31 X X-Axis 65—See also Plot Terminal program 19, 53 Top bar 65 Y Tracking 51, 55 Y-Axis 65—See also Plot Throughput
