Maintenance and Service Guide
Table Of Contents
- Computer features
- Illustrated parts catalog
- Routine care, SATA drive guidelines, and disassembly preparation
- Removal and replacement procedures
- Preparation for disassembly
- Access panel
- Optical drive
- Hard drive
- Front bezel
- Removing the slim bezel blank
- Memory modules (DIMMs)
- Expansion card
- WLAN module
- Serial port
- Hood lock
- Hood sensor
- Fan
- Option board
- Heat sink
- Processor
- Drive cage
- Solid-state drive
- Battery
- USB board
- Card reader
- Speaker
- Power supply
- System board
- Wireless antennas and cables
- Troubleshooting without diagnostics
- Before you call for technical support
- Helpful hints
- Solving general problems
- Cannot access the Computer Setup (F10) Utility when booting the computer
- Computer appears locked up and will not turn off when the power button is pressed
- Computer will not respond to keyboard or mouse
- Computer date and time display is incorrect
- There is no sound or sound volume is too low
- Cannot remove computer cover or access panel
- Poor performance
- Computer powered off automatically and the power light blinks red four times and then white two times
- System does not turn on and the lights on the front of the computer are not blinking
- Solving power problems
- Power supply shuts down intermittently
- Computer turned off automatically, power light blinks red two times followed by a two-second pause, and the computer beeps two times (Beeps stop after fifth iteration but lights continue blinking)
- Power light blinks red four times followed by a two-second pause and the computer beeps four times (Beeps stop after fifth iteration but lights continue blinking)
- Solving hard drive problems
- Solving audio problems
- Solving printer problems
- Solving keyboard and mouse problems
- Solving hardware installation problems
- Solving network problems
- Network driver does not detect network controller
- Network status link light never blinks
- Diagnostics reports a failure
- Diagnostics passes, but the computer does not communicate with the network
- Network controller stopped working when an expansion board was added to the computer
- Network controller stops working without apparent cause
- Cannot connect to network server when attempting remote system installation
- System setup utility reports unprogrammed EEPROM
- Solving memory problems
- System will not boot or does not function properly after installing additional memory modules
- Out of memory error
- Memory count during POST is wrong
- Insufficient memory error during operation.
- Power light blinks red five times followed by a two-second pause and the computer beeps five times (Beeps stop after fifth iteration but lights continue blinking)
- Solving USB flash drive problems
- Solving internet access problems
- Solving software problems
- Computer Setup (F10) Utility
- POST error messages
- Password security and resetting CMOS
- Using HP PC Hardware Diagnostics
- Using HP PC Hardware Diagnostics Windows (select products only)
- Using HP PC Hardware Diagnostics UEFI
- Using Remote HP PC Hardware Diagnostics UEFI settings (select products only)
- Backing up, restoring, and recovering
- Statement of memory volatility
- Power cord set requirements
- Specifications
- Index
Power cord set requirements12
The power supplies on some computers have external power switches.
The voltage select switch feature on the computer permits it to operate from any line voltage of 100 V ac–120
V ac or 220 V ac–240 V ac. Power supplies on those computers that do not have external power switches
are equipped with internal switches that sense the incoming voltage and automatically switch to the proper
voltage.
The power cord set received with the computer meets the requirements for use in the country where you
purchased the equipment.
Power cord sets for use in other countries must meet the requirements of the country where you use the
computer.
General requirements
These requirements are applicable to all countries.
1. The power cord must be approved by an acceptable accredited agency responsible for evaluation in the
c
ountry where the power cord set will be installed.
2. The power cord set must have a minimum current capacity of 10A (7A Japan only) and a nominal voltage
rating of 125 V ac or 250 V ac, as required by each country’s power system.
3. The diameter of the wire must be a minimum of 0.75 mm
2
or 18AWG, and the length of the cord must be
bet
ween 1.8 m (6 ft) and 3.6 m (12 ft).
The power cord should be routed so that it is not likely to be walked on or pinched by items placed upon it or
against it. Particular attention should be paid to the plug, electrical outlet, and the point where the cord exits
from the product.
WARNING! Do not operate this product with a damaged power cord set. If the power cord set is damaged in
any m
anner, replace it immediately.
Japanese power cord requirements
For use in Japan, use only the power cord received with this product.
IMPORTANT: Do not use the power cord received with this product on any other products.
Country-specic requirements
This information provides additional requirements
specic to a country.
Table 12-1 Power cord country-specic
requirements
Country Accrediting Agency Country Accrediting Agency
Australia (1)
Austria (1)
EANSW
OVE
Italy (1)
Japan (3)
IMQ
METI
Power cord set requirements 111