Maintenance and Service Guide
Table Of Contents
- Computer features
- Illustrated parts catalog
- Routine care, SATA drive guidelines, and disassembly preparation
- Removal and replacement procedures
- Preparation for disassembly
- Access panel
- Optical drive
- Hard drive
- Front bezel
- Removing the slim bezel blank
- Memory modules (DIMMs)
- Expansion card
- WLAN module
- Serial port
- Hood lock
- Hood sensor
- Fan
- Option board
- Heat sink
- Processor
- Drive cage
- Solid-state drive
- Battery
- USB board
- Card reader
- Speaker
- Power supply
- System board
- Wireless antennas and cables
- Troubleshooting without diagnostics
- Before you call for technical support
- Helpful hints
- Solving general problems
- Cannot access the Computer Setup (F10) Utility when booting the computer
- Computer appears locked up and will not turn off when the power button is pressed
- Computer will not respond to keyboard or mouse
- Computer date and time display is incorrect
- There is no sound or sound volume is too low
- Cannot remove computer cover or access panel
- Poor performance
- Computer powered off automatically and the power light blinks red four times and then white two times
- System does not turn on and the lights on the front of the computer are not blinking
- Solving power problems
- Power supply shuts down intermittently
- Computer turned off automatically, power light blinks red two times followed by a two-second pause, and the computer beeps two times (Beeps stop after fifth iteration but lights continue blinking)
- Power light blinks red four times followed by a two-second pause and the computer beeps four times (Beeps stop after fifth iteration but lights continue blinking)
- Solving hard drive problems
- Solving audio problems
- Solving printer problems
- Solving keyboard and mouse problems
- Solving hardware installation problems
- Solving network problems
- Network driver does not detect network controller
- Network status link light never blinks
- Diagnostics reports a failure
- Diagnostics passes, but the computer does not communicate with the network
- Network controller stopped working when an expansion board was added to the computer
- Network controller stops working without apparent cause
- Cannot connect to network server when attempting remote system installation
- System setup utility reports unprogrammed EEPROM
- Solving memory problems
- System will not boot or does not function properly after installing additional memory modules
- Out of memory error
- Memory count during POST is wrong
- Insufficient memory error during operation.
- Power light blinks red five times followed by a two-second pause and the computer beeps five times (Beeps stop after fifth iteration but lights continue blinking)
- Solving USB flash drive problems
- Solving internet access problems
- Solving software problems
- Computer Setup (F10) Utility
- POST error messages
- Password security and resetting CMOS
- Using HP PC Hardware Diagnostics
- Using HP PC Hardware Diagnostics Windows (select products only)
- Using HP PC Hardware Diagnostics UEFI
- Using Remote HP PC Hardware Diagnostics UEFI settings (select products only)
- Backing up, restoring, and recovering
- Statement of memory volatility
- Power cord set requirements
- Specifications
- Index
Operating guidelines
This information details how to prevent overheating and to help prolong the life of the computer.
● Keep the computer away from excessive moisture, direct sunlight, and extremes of heat and cold.
● Operate the computer on a sturdy, level surface. Leave a 10.2 cm (4 inch) clearance on all vented sides of
the c
omputer and above the monitor to permit the required airow.
● Never restrict the airow into the computer by blocking any vents or air intakes. Do not place the
keyboard, with the keyboard feet down, directly against the front of the desktop unit as this also restricts
airow.
● Occasionally clean the air vents on all vented sides of the computer. Lint, dust, and other foreign matter
can block the vents and limit the airow. Be sure to unplug the computer before cleaning the air vents.
● Never operate the computer with the cover or side panel removed.
● Do not stack computers on top of each other or place computers so near each other that they are subject
t
o each other’s recirculated or preheated air.
● If the computer is to be operated within a separate enclosure, intake and exhaust ventilation must be
provided on the enclosure, and the same operating guidelines listed previously still apply.
● Keep liquids away from the computer and keyboard.
● Never cover the ventilation slots on the monitor with any type of material.
● Install or enable power management functions of the operating system or other software, including Sleep
s
tates.
Routine care
Use this information to properly care for your computer.
General cleaning safety precautions
Use this information to safely clean your computer.
1. Never use solvents or ammable solutions to clean the computer.
2. Never immerse any parts in water or cleaning solutions; apply any liquids to a clean cloth and then use
the cloth on the component.
3. Always unplug the computer when cleaning with liquids or damp cloths.
4. Always unplug the computer before cleaning the keyboard, mouse, or air vents.
5. Disconnect the keyboard before cleaning it.
6. Wear safety glasses equipped with side shields when cleaning the keyboard.
Removing dirt and debris from your computer
Here are the recommended steps to clean dirt and debris from your computer.
14 Chapter 3 Routine care, SATA drive guidelines, and disassembly preparation