Maintenance and Service Guide
Table Of Contents
- Computer features
- Illustrated parts catalog
- Routine care, SATA drive guidelines, and disassembly preparation
- Removal and replacement procedures
- Preparation for disassembly
- Access panel
- Optical drive
- Hard drive
- Front bezel
- Removing the slim bezel blank
- Memory modules (DIMMs)
- Expansion card
- WLAN module
- Serial port
- Hood lock
- Hood sensor
- Fan
- Option board
- Heat sink
- Processor
- Drive cage
- Solid-state drive
- Battery
- USB board
- Card reader
- Speaker
- Power supply
- System board
- Wireless antennas and cables
- Troubleshooting without diagnostics
- Before you call for technical support
- Helpful hints
- Solving general problems
- Cannot access the Computer Setup (F10) Utility when booting the computer
- Computer appears locked up and will not turn off when the power button is pressed
- Computer will not respond to keyboard or mouse
- Computer date and time display is incorrect
- There is no sound or sound volume is too low
- Cannot remove computer cover or access panel
- Poor performance
- Computer powered off automatically and the power light blinks red four times and then white two times
- System does not turn on and the lights on the front of the computer are not blinking
- Solving power problems
- Power supply shuts down intermittently
- Computer turned off automatically, power light blinks red two times followed by a two-second pause, and the computer beeps two times (Beeps stop after fifth iteration but lights continue blinking)
- Power light blinks red four times followed by a two-second pause and the computer beeps four times (Beeps stop after fifth iteration but lights continue blinking)
- Solving hard drive problems
- Solving audio problems
- Solving printer problems
- Solving keyboard and mouse problems
- Solving hardware installation problems
- Solving network problems
- Network driver does not detect network controller
- Network status link light never blinks
- Diagnostics reports a failure
- Diagnostics passes, but the computer does not communicate with the network
- Network controller stopped working when an expansion board was added to the computer
- Network controller stops working without apparent cause
- Cannot connect to network server when attempting remote system installation
- System setup utility reports unprogrammed EEPROM
- Solving memory problems
- System will not boot or does not function properly after installing additional memory modules
- Out of memory error
- Memory count during POST is wrong
- Insufficient memory error during operation.
- Power light blinks red five times followed by a two-second pause and the computer beeps five times (Beeps stop after fifth iteration but lights continue blinking)
- Solving USB flash drive problems
- Solving internet access problems
- Solving software problems
- Computer Setup (F10) Utility
- POST error messages
- Password security and resetting CMOS
- Using HP PC Hardware Diagnostics
- Using HP PC Hardware Diagnostics Windows (select products only)
- Using HP PC Hardware Diagnostics UEFI
- Using Remote HP PC Hardware Diagnostics UEFI settings (select products only)
- Backing up, restoring, and recovering
- Statement of memory volatility
- Power cord set requirements
- Specifications
- Index
Interpreting POST diagnostic front panel lights and audible codes
This section
identies the front panel light codes as well as the audible codes that can occur before or during
POST that might not have an error code or text message associated with them.
CAUTION: When the computer is plugged into an AC power source, voltage is always applied to the system
bo
ard. To reduce the risk of personal injury from electrical shock and/or hot surfaces, be sure to disconnect
the power cord from the AC outlet and allow the internal system components to cool before touching.
During the system validation phase that occurs at system startup, the BIOS validates the functionality of the
f
ollowing subsystems and conditions:
● AC adapter
● System board power
● Processor failure
● BIOS corruption
● Memory failure
● Graphics failure
● System board failure
● BIOS authentication failure
If an error is detected,
specic patterns of long and short blinks, accompanied by long and short beeps (where
applicable) are used to identify the error. These patterns make up a two-part code:
● Major: The category of the error
● Minor: The specic error within the category
NOTE: Single beep and blink codes are not used.
Table 7-2 Beep pattern error identication
Number of long beeps/blinks Error category
1 Not used
2 BIOS
3 Hardware
4 Thermal
5 System board
Patterns of blink/beep codes are determined by using the following parameters:
● 1 second pause occurs after the last major blink.
● 2 second pause occurs after the last minor blink.
● Beep error code sequences occur for the rst ve iterations of the pattern and then stop.
Interpreting POST diagnostic front panel lights and audible codes 89