Maintenance and Service Guide
Table Of Contents
- Product overview
- Standard features
- Integrated features
- Stand options
- HP Engage One Basic I/O Connectivity Base components
- HP Engage One Advanced I/O Connectivity Base components
- Connecting an AC adapter to power
- Locating the Engage One power button
- Locating the I/O connectivity base power button
- Adjusting the Engage One head unit
- Engage One serial number location
- I/O connectivity base serial number location
- Illustrated parts catalog
- Routine care, SATA drive guidelines, and disassembly preparation
- Removal and replacement procedures
- Preparation for disassembly
- Attaching an I/O connectivity base to the Engage One
- Connecting a standalone I/O connectivity base to the Engage One
- Configuring the I/O connectivity base’s powered serial ports
- Connecting a standalone optional fingerprint reader to the I/O connectivity base
- Attaching an optional fingerprint reader to the I/O connectivity base
- Removing and attaching the Engage One head unit to the stand
- Mounting the Engage One head unit to a wall
- Mounting the Engage One to a counter top
- Installing a security cable on the I/O connectivity base
- Installing a security cable on the Engage One column
- Installing a security screw on the Engage One head unit and stand
- Installing a security screw on the Engage One head unit and VESA mount
- Removing and replacing the column printer
- Removing the display panel
- System board components
- Installing a 2 x 20 customer-facing display (CFD)
- Memory modules
- Removing and installing an M.2 solid-state drive (SSD)
- Removing the WLAN module
- Removing the heat sink
- Removing the fan assembly
- Removing the speakers
- Removing the power button board
- Removing the MSR (Magnetic Stripe Reader)
- Removing the MSR LED board
- Removing the system board
- Removing the antennas
- Using the column printer
- Cable routing configurations
- Cable matrix for Engage One with integrated column printer and basic I/O connectivity base
- Cable matrix for Engage One with integrated column printer and advanced I/O connectivity base
- Cable matrix for Engage One without I/O connectivity base
- Cable matrix for Engage One with I/O connectivity base
- Cable matrix for Engage One with basic I/O connectivity base and standalone printer
- Cable matrix for Engage One with advanced I/O connectivity base and standalone printer
- Configuring the software
- Computer Setup (F10) Utility
- POST error messages and diagnostic front panel LEDs and audible codes
- Password security and resetting CMOS
- Using HP PC Hardware Diagnostics (UEFI)
- Troubleshooting without diagnostics
- Safety and comfort
- Before you call for technical support
- Helpful hints
- Solving retail system-specific problems
- Solving general problems
- Solving printer problems
- Solving hardware installation problems
- Solving network problems
- Solving memory problems
- Solving USB flash drive problems
- Solving Internet access problems
- Solving software problems
- System backup and recovery
- Power cord set requirements
- Statement of memory volatility
- Specifications
- Index
Table 8-3 Computer Setup—Advanced (for advanced users) (continued)
Option Description
Enabling this feature reduces the power of the system as much as possible in the S5 state. Power is
removed from the wake up circuitry, the expansion slots, and any management features while in S5.
Default is disabled.
SATA Power Management (enable/disable)
Enables or disables SATA bus and/or device power management. Default is enabled.
PCI Express Power Management (enable/disable)
Enabling this option permits the PCI Express links to use Active Power State Management (ASPM) to enter
lower power states while not in use. Default is enabled.
Unique Sleep State Blink Rates (enable/disable)
This feature is designed to provide a visual indication of what sleep state the system is in. Each sleep
state has a unique blink pattern. Default is disabled.
NOTE: A normal shutdown goes to the S4 state.
S0 (On) = Solid white LED.
S3 (Stand By)= 3 blinks at 1Hz (50% duty cycle) followed by a pause of 2 seconds (white LED) — repeated
cycles of 3 blinks and a pause.
S4 (Hibernation)= 4 blinks at 1Hz (50% duty cycle) followed by a pause of 2 seconds (white LED) —
repeated cycles of 4 blinks and a pause.
S5 (Soft O) = LED is o.
Recovering the Conguration Settings
This method of recovery requires that you rst perform the Save to Removable Media command with the
Computer Setup (F10) Utility before Restore is needed. (See Computer Setup–Main on page 79 in the
Computer Setup—File table.)
NOTE: It is recommended that you save any modied computer conguration settings to a USB ash media
device and save the device for possible future use.
To restore the conguration, insert the USB ash media device with the saved conguration and perform the
Restore from Removable Media command with the Computer Setup (F10) Utility. (See Computer Setup–Main
on page 79 in the Computer Setup—File table.)
Recovering the Conguration Settings 87