Maintenance and Service Guide
Table Of Contents
- Product overview
- Standard features
- Integrated features
- Stand options
- HP Engage One Basic I/O Connectivity Base components
- HP Engage One Advanced I/O Connectivity Base components
- Connecting an AC adapter to power
- Locating the Engage One power button
- Locating the I/O connectivity base power button
- Adjusting the Engage One head unit
- Engage One serial number location
- I/O connectivity base serial number location
- Illustrated parts catalog
- Routine care, SATA drive guidelines, and disassembly preparation
- Removal and replacement procedures
- Preparation for disassembly
- Attaching an I/O connectivity base to the Engage One
- Connecting a standalone I/O connectivity base to the Engage One
- Configuring the I/O connectivity base’s powered serial ports
- Connecting a standalone optional fingerprint reader to the I/O connectivity base
- Attaching an optional fingerprint reader to the I/O connectivity base
- Removing and attaching the Engage One head unit to the stand
- Mounting the Engage One head unit to a wall
- Mounting the Engage One to a counter top
- Installing a security cable on the I/O connectivity base
- Installing a security cable on the Engage One column
- Installing a security screw on the Engage One head unit and stand
- Installing a security screw on the Engage One head unit and VESA mount
- Removing and replacing the column printer
- Removing the display panel
- System board components
- Installing a 2 x 20 customer-facing display (CFD)
- Memory modules
- Removing and installing an M.2 solid-state drive (SSD)
- Removing the WLAN module
- Removing the heat sink
- Removing the fan assembly
- Removing the speakers
- Removing the power button board
- Removing the MSR (Magnetic Stripe Reader)
- Removing the MSR LED board
- Removing the system board
- Removing the antennas
- Using the column printer
- Cable routing configurations
- Cable matrix for Engage One with integrated column printer and basic I/O connectivity base
- Cable matrix for Engage One with integrated column printer and advanced I/O connectivity base
- Cable matrix for Engage One without I/O connectivity base
- Cable matrix for Engage One with I/O connectivity base
- Cable matrix for Engage One with basic I/O connectivity base and standalone printer
- Cable matrix for Engage One with advanced I/O connectivity base and standalone printer
- Configuring the software
- Computer Setup (F10) Utility
- POST error messages and diagnostic front panel LEDs and audible codes
- Password security and resetting CMOS
- Using HP PC Hardware Diagnostics (UEFI)
- Troubleshooting without diagnostics
- Safety and comfort
- Before you call for technical support
- Helpful hints
- Solving retail system-specific problems
- Solving general problems
- Solving printer problems
- Solving hardware installation problems
- Solving network problems
- Solving memory problems
- Solving USB flash drive problems
- Solving Internet access problems
- Solving software problems
- System backup and recovery
- Power cord set requirements
- Statement of memory volatility
- Specifications
- Index
9 POST error messages and diagnostic front
panel LEDs and audible codes
This appendix lists the error codes, error messages, and the various indicator light and audible sequences
that you may encounter during Power-On Self-Test (POST) or computer restart, the probable source of the
problem, and steps you can take to resolve the error condition.
POST Message Disabled suppresses most system messages during POST, such as memory count and non-
error text messages. If a POST error occurs, the screen will display the error message. To manually switch to
the POST Messages Enabled mode during POST, press any key (except F10, F11, or F12). The default mode is
POST Message Disabled.
The speed at which the computer loads the operating system and the extent to which it is tested are
determined by the POST mode selection.
Quick Boot is a fast startup process that does not run all of the system level tests, such as the memory test.
Full Boot runs all of the ROM-based system tests and takes longer to complete.
Full Boot may also be enabled to run every 1 to 30 days on a regularly scheduled basis. To establish the
schedule, recongure the computer to the Full Boot Every x Days mode, using Computer Setup.
NOTE: For more information on Computer Setup, see Computer Setup (F10) Utility on page 77.
POST numeric codes and text messages
This section covers those POST errors that have numeric codes associated with them. The section also
includes some text messages that may be encountered during POST.
NOTE: The computer will beep once after a POST text message is displayed on the screen.
Control panel message Description Recommended action
002-Option ROM Checksum Error System ROM or expansion board option ROM
checksum.
1. Verify the correct ROM.
2. Flash the ROM if needed.
3. If an expansion board was recently added,
remove it to see if the problem remains.
4. Clear CMOS. (See Password security and
resetting CMOS on page 95.)
5. If the message disappears, there may be a
problem with the expansion card.
6. Replace the system board.
003-System Board Failure DMA or timers. 1. Clear CMOS. (See Password security and
resetting CMOS on page 95.)
2. Remove expansion boards.
3. Replace the system board.
005-Real-Time Clock Power Loss Invalid time or date in conguration memory. Reset the date and time under Control Panel
(Computer Setup can also be used). If the
88 Chapter 9 POST error messages and diagnostic front panel LEDs and audible codes