HP 2000sa G2 Modular Smart Array User Guide Part number: 488320-005 First edition: January 2013
Legal and notice information © Copyright 2009, 2013 Hewlett-Packard Development Company, L.P. The information combined herein is subject to change without notice. The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty. HP shall not be liable for technical or editorial errors or omissions contained herein.
Contents About this guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Intended audience . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Prerequisites. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Related documentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Document conventions and symbols . . . . . . . .
Blade enclosure configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 Blade servers/two 3Gb SAS BL switches. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 Connecting remote management hosts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 5 Basic operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Temperature sensors. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59 Power supply module voltage sensors. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60 A Environmental requirements and specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61 Safety requirements. . . . . . . . . . . . . . . . . . . Site requirements and guidelines . . . . . . . . .
Figures 1 2 3 4 5 6 Cabling connections between a single-controller enclosure and one MSA2000 3.5" 12-drive enclosure Cabling connections between a dual-controller enclosure and one MSA2000 3.5" 12-drive enclosure. Cabling connections between a dual-controller enclosure and three MSA2000 3.5" 12-drive enclosures . Cabling connections between a dual-controller enclosure and one MSA70 drive enclosure. . . . . . . . . Cabling connections between a dual-controller enclosure and three MSA70 drive enclosures . .
Tables 1 2 3 4 5 6 7 8 9 10 11 12 13 14 Document conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Installation checklist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SAS cable requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Terminal emulator display settings . . . . . . . . . . . . . . . . . . .
About this guide This guide provides information about the HP StorageWorks 2312sa G2 Modular Smart Array and 2324sa G2 Modular Smart Array. Product branding initially included the term StorageWorks, which is no longer used. Although the term is removed from the title and footers in this version of the document, references to related documents, media, and user interfaces use the term.
Document conventions and symbols Document conventions Table 1 Convention Element Medium blue text: Figure 1 Cross-reference links and e-mail addresses Medium blue, underlined text (http://www.hp.
Rack stability WARNING! To reduce the risk of personal injury or damage to equipment: • Extend leveling jacks to the floor. • Ensure that the full weight of the rack rests on the leveling jacks. • Install stabilizing feet on the rack. • In multiple-rack installations, secure racks together. • Extend only one rack component at a time. Racks may become unstable if more than one component is extended.
• http://www.hp.com/go/msa • http://www.hp.com/service_locator • http://www.hp.com/go/storage • http://www.hp.com/support/ • http://www.docs.hp.com Documentation feedback HP welcomes your feedback. To make comments and suggestions about product documentation, please send a message to storagedocs.feedback@hp.com. All submissions become the property of HP.
1 Overview The 2312sa G2 Modular Smart Array and 2324sa G2 Modular Smart Array are high-performance storage solutions that combine outstanding performance with high reliability, availability, flexibility, and manageability. Features and benefits Product features and supported options are subject to change.
Overview
2 Components Front panel components 2312sa G2 Right ear Left ear MSA2000 4 1 2 5 3 1 Enclosure ID LED 4 Unit Identification (UID) LED 2 Disk drive Online/Activity LED 5 Fault ID LED 3 Disk drive Fault/UID LED 6 Heartbeat LED 6 2324sa G2 Right ear Left ear MSA2000 4 1 2 5 3 1 Enclosure ID LED 4 Unit Identification (UID) LED 2 Disk drive Online/Activity LED 5 Fault ID LED 3 Disk drive Fault/UID LED 6 Heartbeat LED 6 HP 2000sa G2 Modular Smart Array User Guide 17
Disk drive bay numbers 2312sa G2 1 4 7 10 2 5 8 11 3 6 9 12 MSA2000 2324sa G2 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 Rear panel components 2312sa G2 and 2324sa G2 1 2 3 LINK 45 6 1 2 LINK SAS 3 SAS 4 SAS 1 SAS 2 ACT ACT LINK LINK ACT ACT LINK LINK SAS 3 SAS 4 SAS 1 SAS 2 ACT ACT LINK LINK ACT ACT 8 9 - 18 7 1 AC Power supplies 6 Service port (used by service personnel only) 2 AC Power switches 7 Expansion port 3 Host
MSA2000 3.5" 12-drive enclosure 1 2 3 4 5 0 1 2 0 6 1 Power supplies 4 Service port (used by service personnel only) 2 Power switches 5 SAS Out port (connects to another drive enclosure) 3 SAS In port (connects to a controller enclosure) 6 Optional I/O module MSA70 2.5” 25-drive enclosure The 2324sa G2 can also be attached to an MSA70 that is running firmware version 2.18 or later.
CAUTION: To preserve the existing data stored in the CompactFlash, you must transport the CompactfFlash from the failed controller to the replacement controller using a procedure outlined in the HP StorageWorks 2312sa/2324sa G2 controller replacement instructions, shipped with the replacement controller. Failure to use this procedure will result in the loss of data stored in the cache module. The CompactFlash must stay with the same enclosure.
3 Installing the enclosures Installation checklist The following table outlines the steps required to install the enclosures and initially configure the system. To ensure a successful installation, perform the tasks in the order they are presented. Table 2 Installation checklist Step Task Where to find procedure 1. Install the controller enclosure and optional drive enclosures in the rack, and attach ear caps. See the racking instructions poster. 2.
Connecting controller and drive enclosures Connecting controller and MSA2000 3.5" 12-drive enclosures You can connect up to four MSA2000 3.5" 12-drive enclosures to a 2312sa G2 and up to three MSA2000 3.5" 12-drive enclosures to a 2324sa G2. The cabling diagrams shown in this section show the recommended fault-tolerant cabling patterns. Connecting an MSA2000 3.5" 12-drive enclosure to a 2312sa G2 or 2324sa G2 requires mini-SAS to SAS cables.
Table 3 SAS cable requirements Item MSA2000 G2 controller MSA70 I/O module MSA2000 3.5” 12-drive I/O module MSA2000 G2 controller N/A mini-SAS to mini-SAS mini-SAS to SAS MSA70 I/O module mini-SAS to mini-SAS mini-SAS to mini-SAS mini-SAS to SAS MSA2000 3.5” 12-drive I/O module mini-SAS to SAS mini-SAS to SAS SAS to SAS Mini-SAS to SAS cables must be purchased separately. 0.5m cables are recommended for mini-SAS to SAS connections and mini-SAS to mini-SAS connections, respectively.
Controller A 1A Controller B 1B Out 2A In Out 2B Out 3A In In 3B Out In Out 4A In Out 4B In Figure 3 Cabling connections between a dual-controller enclosure and three MSA2000 3.
Controller A 0A Controller B 0B 1A In Out 2A In Out 3A In Out 1B In Out 2B In Out 3B In Out Figure 5 Cabling connections between a dual-controller enclosure and three MSA70 drive enclosures HP 2000sa G2 Modular Smart Array User Guide 25
Controller A Controller B 1A In Out 0A 0B 1B In Out In Out 2A In Out 2B 3A In Out 3B In Out In Out 4A In Out 4B Figure 6 Cabling connections between a dual-controller enclosure and mixed drive enclosures. TIP: For comprehensive configuration options and associated illustrations, see the HP StorageWorks 2000 G2 Modular Smart Array Cable Configuration Guide. Testing enclosure connections 1. Press the power switches at the back of each drive enclosure to On.
Obtaining IP values NOTE: For help with configuring your MSA2000 G2 product, also see the MSA2000 Software Support/Documentation CD shipped with your product. Setting management port IP addresses using DHCP 1. Look in the DHCP server’s pool of leased addresses for two IP addresses assigned to “HP StorageWorks MSA Storage.” 2. Use the MSA Device Discovery Tool to discover “HP StorageWorks MSA2300sa” storage devices on the local LAN through SNMP.
2. Use the provided micro-DB9 serial cable to connect controller A to a serial port on a host computer. SAS SAS 3 1 SAS 4 SAS 2 Serv CLI ice DIRT SAS Y CACH ACTIV E 1 ITY LINK CLI Connect serial cable to CLI port on controller faceplate Your package contents include a micro-DB9-to-DB9 serial cable. If necessary, use a DB9-to-DB25 adapter (not included) for connecting the serial cable to a DB25 serial port on the host computer. 3.
# set network-parameters ip 192.168.0.11 netmask 255.255.255.0 gateway 193.168.0.10 controller b 7. Type the following command to verify the new IP addresses: show network-parameters Network parameters, including the IP address, subnet mask, and gateway address are displayed for each controller. 8. Use the ping command to verify network connectivity. For example: # ping 192.168.0.10 (gateway) Info: Pinging 192.168.0.10 with 4 packets. Success: Command completed successfully.
Installing the enclosures
4 Connecting hosts Host system requirements Data hosts connected to 2312sa G2 and 2324sa G2 arrays must meet the following requirements: • Depending on your system configuration, data host operating systems may require that multi-pathing is supported. TIP: See the HP StorageWorks MSA2000 Family VDS and VSS Hardware Providers Installation Guide and HP StorageWorks MSA2000 Family MPIO DSM Installation Guide to aid in planning and implementing your MPIO DSM installation.
The 2312sa Modular Smart Array and 2324sa Modular Smart Array use Unified LUN Presentation (ULP) — a controller firmware feature enabling hosts to access mapped volumes via host ports — without the need for internal or external switches. Connecting direct attach configurations The 2312sa G2 and 2324sa G2 support up to eight direct-connect server connections, four per controller. Connect appropriate cables from the servers’ HBAs to the controller host ports as shown in the following illustrations.
Connecting switch attach configurations IMPORTANT: • Any number or combination of LUNs can be shared among a maximum of 32 single-density blade servers, or 16 dual-density blade servers, provided the total does not exceed 512 LUNs per MSA2000sa G2. • Single-density configurations support two 3Gb SAS BL Switches per blade enclosure. • Dual-density configurations support four 3Gb SAS BL Switches per blade enclosure. • Only use supported mini-SAS 4x cables with 3Gb connectors.
Blade enclosure configuration Blade servers/two 3Gb SAS BL switches 29 29 28 28 27 27 26 26 25 25 24 24 23 23 22 22 21 21 20 20 19 19 OK 18 18 OK 17 17 16 16 15 15 14 14 13 13 12 12 11 11 10 10 09 09 08 08 07 07 Connecting remote management hosts The management host directly manages systems out-of-band over an Ethernet network. 1. Connect an Ethernet cable to the network port on each controller. 2.
5 Basic operation Powering on/powering off Before powering on the enclosure for the first time: • Install all disk drives in the enclosure so the controller can identify and configure them at power-up. • Connect the cables and power cords to the enclosure as explained in the installation poster.
For software and firmware updates, go to http://www.hp.com/go/msa. Select MSA SAN Arrays, select your product, and go to Support. For detailed steps on updating the firmware, see the reference guide or the CLI reference guide. For information on logging into SMU, see Configuring a system for the first time on page 45.
6 LED descriptions Front panel LEDs Right ear Left ear MSA2000 4 1 2 5 3 6 Right ear Left ear MSA2000 4 1 2 5 3 6 LED Description Definition 1 Enclosure ID Green — On Enables you to correlate the enclosure with logical views presented by management software. Sequential enclosure ID numbering of controller enclosures begins with the integer 1. The enclosure ID for an attached drive enclosure is nonzero. 2 Disk drive Online/Activity See Table 6 on page 38, Disk drive LED combinations.
Disk drive LEDs 3.5” LFF disk drive 2 1 2.5” SFF disk drive 2 LED Description 1 Fault/UID (amber/blue) 2 Online/Activity (green) Table 6 38 1 Disk drive LED combinations Online/Activity (green) Fault/UID (amber/blue) Description On Off Normal operation. The drive is online, but it is not currently active. Blinking irregularly Off The drive is active and operating normally. Off Amber; blinking regularly (1 Hz) Offline; the drive is not being accessed.
Table 6 Disk drive LED combinations (continued) Online/Activity (green) Fault/UID (amber/blue) Blinking regularly (1 Hz) Off Description CAUTION: Do not remove the drive. Removing a drive may terminate the current operation and cause data loss. The drive is rebuilding. Off Off Either there is no power, the drive is offline, or the drive is not configured. 1. This Fault/UID state can indicate that the disk is a leftover. The fault may involve metadata on the disk, rather than the disk itself.
Rear panel LEDs 2312sa G2 and 2324sa G2 1 4 LINK SAS 4 SAS 1 SAS 2 ACT LINK ACT ACT LINK LINK SAS 3 SAS 4 SAS 1 SAS 2 ACT ACT LINK LINK ACT 40 1 LINK SAS 3 ACT LINK 2 5 6 7 ACT 3 89 : ; w LED Description Definition 1 Power supply LEDs See Power supply LEDs on page 43. 2 Host 3Gb SAS Link Status (ports 1-4) Green — The port is connected and the link is up. Off — The port is empty or the link is down.
LED Description Definition 10 Cache Status Green — Cache is dirty (contains unwritten data) and operation is normal. The unwritten information can be log or debug data that remains in the cache, so a Green cache status LED does not, by itself, indicate that any user data is at risk or that any action is necessary. Off — In a working controller, cache is clean (contains no unwritten data). Blinking green — A CompactFlash flush or cache self-refresh is in progress.
MSA2000 3.5" 12-drive enclosure 1 2 1 0 0 3 4 5 6 7 LED Description Definition 1 Power supply LEDs See Power supply LEDs on page 43. 2 Unit Locator Off — Normal operation. Blinking white— Physically identifies the expansion module. 3 SAS In Port Status Green — Port link is up and connected. Off — Port is empty or link is dow.n 4 OK to Remove Not implemented. 5 Fault/Service Required Amber — A fault has been detected or a service action is required.
Power supply LEDs Power redundancy is achieved through two independent load-sharing power supplies. In the event of a power supply failure, or the failure of the power source, the storage system can operate continuously on a single power supply. Greater redundancy can be achieved by connecting the power supplies to separate circuits. AC model 1 1 2 2 DC model LED Description Definition 1 Input Source Power good Green — Power is on and input voltage is normal.
LED descriptions
7 Configuring a system for the first time Configuring your web browser for SMU Before using SMU to perform remaining steps, ensure that your web browser is properly configured according to the following guidelines: • Your browser must be Mozilla Firefox 1.5 or Microsoft Internet Explorer 6, or later. For better performance, use Firefox or Internet Explorer 7 or later. NOTE: Check the QuickSpecs for currently supported browsers. QuickSpecs can be found from your HP MSA products page at http://www.hp.
• The System Status panel shows how many events of each severity have occurred in the system. To view event details, click a severity icon. • Do not use the browser's Back, Forward, Reload, or Refresh buttons. SMU is essentially a single page that is automatically updated to show current data. You do not need to refresh it, and if you click Back, you may exit the application. • An asterisk (*) identifies a required setting. • Many tables can be sorted by a specific column.
To obtain the date and time from an NTP server 1. In the Configuration View panel, right-click the system and select Configuration > System Settings > Date, Time. The date and time options appear. 2. Set the options: • NTP. Select Enabled. • NTP Time Zone Offset. Optional. If the system timestamps should use the NTP server's time zone instead of the local time zone, enter the time zone offset. • NTP Server Address. Optional.
Using the Configuration Wizard The Configuration Wizard helps you initially configure the system or change system configuration settings. The wizard has several steps, which are highlighted at the bottom of the panel as you complete them. The last step prompts you to confirm changes before applying them. If you cancel the wizard, no changes are made.
Using the Provisioning Wizard The Provisioning Wizard helps you create a vdisk with volumes, and to map the volumes to hosts. The wizard has several steps, which are highlighted at the bottom of the panel as you complete them. The last step prompts you to confirm changes before applying them. If you cancel the wizard, no changes are made.
Configuring a system for the first time
8 Troubleshooting Fault isolation methodology The 2000sa G2 Modular Smart Array storage system provides many ways to isolate faults within the system. This section presents the basic methodology used to locate faults and the associated FRUs (Field Replaceable Units).
Correcting enclosure IDs When installing a system with drive enclosures attached, the enclosure IDs might not agree with the physical cabling order. This is because the controller might have been previously attached to some of the same enclosures during factory testing and it attempts to preserve the previous enclosure IDs if possible. To correct this condition, make sure that both controllers are up, and perform a rescan using SMU or the CLI.
Are both drive module LEDs off (Online/Activity and Fault/UID)? Answer Possible Reasons Actions Yes • There is no power. • Check that the drive is fully inserted and latched in place, and that the enclosure is powered on. • The drive is offline. • The drive is not configured. Is the drive module Fault/UID LED blinking amber? Answer Possible Reasons Actions No, but the The drive is rebuilding. Online/Activity LED is blinking. No action required. Yes, and the The drive is offline.
Is a connected port’s Expansion Port Status LED off? Answer Possible Reasons Actions No System functioning properly. No action required. Yes The link is down. • Check cable connections and reseat if necessary. • Inspect cable for damage. • Swap cables to determine if fault is caused by a defective cable. Replace cable if necessary. • In SMU, review event logs for indicators of a specific fault in a host data path component. • Contact an authorized service provider for assistance.
Is the drive enclosure Fault/Service Required LED amber? Answer Possible Reasons Actions No System functioning properly. No action required. Yes (blinking) One of the following errors occurred: • Check the event log for specific information regarding the fault. • Hardware-controlled power-up error • Isolate the fault. • Cache flush error • Replace if necessary. • Contact an authorized service provider for assistance. • Cache self-refresh error Yes A fault occurred.
Controller failure in a single-controller configuration Cache memory is flushed to CompactFlash in the case of a controller failure or power loss. During the write to CompactFlash process only the components needed to write the cache to the CompactFlash are powered by the super-capacitor. This process typically takes 60 seconds per 1 Gbyte of cache. After the cache is copied to CompactFlash, the remaining power left in the super-capacitor is used to refresh the cache memory.
Isolating a host-side connection fault During normal operation, when a controller module host port is connected to a data host, the port’s host link status LED and host link activity LED are green. If there is I/O activity, the host activity LED blinks green. If data hosts are having trouble accessing the storage system, and you cannot locate a specific fault or cannot access the event logs, use the following procedure. This procedure requires scheduled downtime.
Isolating a controller module expansion port connection fault During normal operation, when a controller module’s expansion port is connected to a drive enclosure, the expansion port status LED is green. If the connected port’s expansion port LED is off, the link is down. Use the following procedure to isolate the fault. This procedure requires scheduled downtime. NOTE: Do not perform more than one step at a time. Changing more than one variable at a time can complicate the troubleshooting process. 1.
Sensor locations The storage system monitors conditions at different points within each enclosure to alert you to problems. Power, cooling fan, temperature, and voltage sensors are located at key points in the enclosure. In each controller module and expansion module, the enclosure management processor (EMP) monitors the status of these sensors to perform SCSI enclosure services (SES) functions. The following sections describe each element and its sensors.
Table 9 Controller module temperature sensors (continued) Description Normal operating Warning range operating range Critical operating range Shutdown values Onboard temperature 2 0–70°C None None None Onboard temperature 3 (Capacitor temperature) 0–70°C None None None CM temperature 5–50°C <=5°C, >= 50°C <=0°C, >= 55°C None When a power supply sensor goes out of range, the Fault/ID LED illuminates amber and an event is logged to the event log.
A Environmental requirements and specifications Safety requirements Install the system in accordance with the local safety codes and regulations at the facility site. Follow all cautions and instructions marked on the equipment. Site requirements and guidelines The following sections provide requirements and guidelines that you must address when preparing your site for the installation.
Weight and placement guidelines Refer to Physical requirements on page 63 for detailed size and weight specifications. • The weight of an enclosure depends on the number and type of modules installed. • Ideally, use two people to lift an enclosure. However, one person can safely lift an enclosure if its weight is reduced by removing the power and cooling modules and drive modules. • Do not place enclosures in a vertical position. Always install and operate the enclosures in a horizontal orientation.
NOTE: Connections to this device must be made with shielded cables with metallic RFI/EMI connector hoods in order to maintain compliance with FCC Rules and Regulations. Physical requirements The floor space at the installation site must be strong enough to support the combined weight of the rack, controller enclosures, expansion enclosures, and any additional equipment.
Electrical requirements Site wiring and power requirements Each enclosure has two power and cooling modules for redundancy. If full redundancy is required, use a separate power source for each module. The AC power supply unit in each power and cooling module is auto-ranging and is automatically configured to an input voltage range from 88–264 VAC with an input frequency of 47–63 Hz. The power and cooling modules meet standard voltage requirements for both U.S. and international operation.
B Electrostatic discharge Preventing electrostatic discharge To prevent damaging the system, be aware of the precautions you need to follow when setting up the system or handling parts. A discharge of static electricity from a finger or other conductor may damage system boards or other static-sensitive devices. This type of damage may reduce the life expectancy of the device. To prevent electrostatic damage: • Avoid hand contact by transporting and storing products in static-safe containers.
Electrostatic discharge
C Regulatory compliance and safety Regulatory compliance Federal Communications Commission notice Part 15 of the Federal Communications Commission (FCC) Rules and Regulations has established Radio Frequency (RF) emission limits to provide an interference-free radio frequency spectrum. Many electronic devices, including computers, generate RF energy incidental to their intended function and are, therefore, covered by these rules.
• 1-281-514-3333 To identify this product, refer to the part, Regulatory Model Number, or product number found on the product. Modifications The FCC requires the user to be notified that any changes or modifications made to this device that are not expressly approved by Hewlett-Packard Company may void the user's authority to operate the equipment.
Laser product label The optional label in Figure 6-1 or equivalent may be located on the surface of the HP supplied laser device. This optional label indicates that the product is classified as a CLASS 1 LASER PRODUCT. This label may appear on the laser device installed in your product.
BSMI notice Japanese notice Korean notices Safety Battery replacement notice Your computer is equipped with a lithium manganese dioxide, a vanadium pentoxide, or an alkaline internal battery or battery pack. There is a danger of explosion and risk of personal injury if the battery is incorrectly replaced or mistreated. Replacement is to be done by an HP authorized service provider using the HP spare part designated for this product.
WARNING! Your computer contains an internal lithium manganese dioxide, a vanadium pentoxide, or an alkaline battery pack. There is risk of fire and burns if the battery pack is not properly handled. To reduce the risk of personal injury: • Do not attempt to recharge the battery. • Do not expose to temperatures higher than 60°C. • Do not disassemble, crush, puncture, short external contacts, or dispose of in fire or water. • Replace only with the HP spare part designated for this product.
• Keep electrostatic-sensitive parts in their containers until they arrive at static-free workstations. • Place parts on a grounded surface before removing them from their containers. • Avoid touching pins, leads, or circuitry. • Always be properly grounded when touching a static-sensitive component or assembly (see “Grounding methods” on page 72). Grounding methods There are several methods for grounding.
Index A accessing the CLI 27 accessing the SMU 45 accumulators 71 audience 11 Avis Canadien, regulatory compliance notice 69 B batteries recycling or disposal 71 replacement notice 70 Taiwan EPA recycling and disposal 71 boot straps, using 72 BSMI, regulatory compliance notice 70 C cables FCC compliance statement 34, 63, 68 shielded 34, 63, 68 cabling connecting controller enclosures to drive enclosures 22 connecting enclosure to data hosts 31 routing requirements 62 cache 19 self-refresh mode 41 status 4
F L faults isolating a host-side connection 57 expansion port connection fault 58 methodology 51 FCC (Federal Communications Commission) Class A Equipment, compliance notice 67 Class B Equipment, compliance notice 67 declaration of conformity 67 modifications 68 notice 67 Federal Communications Commission See FCC firmware checking versions 35 updates 35 when to update 35 floor mats, dissipating 72 found new hardware wizard 31 label, laser 69 language field 45 laser international certification and classif
power cord compliance notice 71 current rating 71 replacement 71 set 71 voltage rating 71 power cord requirements 64 power supply LEDs 40 sensors 59 wiring requirements 61 powering on/powering off 35 prerequisite knowledge 11 preventing electrostatic damage 71 Provisioning Wizard 49 R rack stability, warning 13 recycling, battery 71 recycling, Taiwan EPA battery 71 regulatory compliance information number 68 notices BSMI 70 Canada 69 Class A 67 Class B 67 European Union 69 HP series number 68 IEC EMC state
web sites HP documentation 11 HP storage 14 HP Subscriber’s choice 13 web-browser configuration 45 work mat, static-dissipating 72 wrist straps specifications 72 using 72 76
