3Com Router 3000 ADSL2+ Family Getting Started Guide Router 3040 (3C13640) Router 3041 (3C13641) Router 3040E (3CR13640-75) Router 3041E (3CR13641-75) www.3Com.com Part Number: 10014947 Rev.
3Com Router 3000 ADSL2+ Family Getting Started Guide Table of Contents 1. Introduction .....................................................................................................1 About the 3Com Router 3040 ......................................................................................................1 System Specifications ................................................................................................................1 LEDs .................................................
Com Router 3000 ADSL2+ Family Getting Started Guide 1. Introduction The 3Com Router 3000 ADSL2+ Family are ADSL access routers designed for smalloffice/home-office (SOHO) subscribers . They provides an uplink ADSL2+ interface and four downlink layer 2 (L2) switched 10/100 Ethernet interfaces that can be isolated.
3Com Router 3000 ADSL2+ Family Getting Started Guide LEDs LED Description LAN0/LAN1/LAN2/LAN3/WAN SYS PWR OFF means no link is present. ON means a link is present. Blinking means data is being sent or/and received on the AUX port. Blinking means the system is operating normally. Steady ON or OFF means the system is improperly operating. OFF means no power is being supplied. ON means power is being supplied.
3Com Router 3000 ADSL2+ Family Getting Started Guide About the 3Com Router 3041 (1) Ethernet LED (LAN4) (3) Ethernet LED (LAN2) (5) ADSL2+ link LED (DSL LNK) (7) ISDN link LED (ISDN LNK) (9) System LED (SYS) (2) Ethernet LED (LAN3) (4) Ethernet LED (LAN1) (6) ADSL2+ activity LED (DSL ACT) (8) ISDN activity LED (ISDN ACT) (10) Power LED (PWR) Front view of the 3Com Router 3041 (1) Power switch (3) Console port (CONSOLE) (5) Ethernet port 2(LAN2) (7) Ethernet port 4 (LAN4) (2) Power socket (4) Ethernet
3Com Router 3000 ADSL2+ Family Getting Started Guide LEDs LED Description LAN1/LAN2/LAN3/LAN4 DSL LNK DSL ACT ISDN LNK ISDN ACT SYS PWR OFF means no link is present. Steady ON means a link is present. Blinking means the interface is sending and/or receiving data. OFF means no ADSL/ADSL2/ADSL2+ line is activated. Steady ON means the ADSL/ADSL2/ADSL2+ line is activated. Blinking means the connected two parties are negotiating parameters. OFF means no data is being sent or received.
3Com Router 3000 ADSL2+ Family Getting Started Guide 2. Installing the Router You can place your router on a sturdy tabletop or workbench or mount it on a vertical surface. Placing the Router on a Tabletop/Workbench When placing the router on a tabletop or workbench, • Make sure that the tabletop or workbench is clean, flat, and sturdy. • Allow 10 cm (3.9 in.) of clearance around the sides of the chassis. • Do not stack multiple routers together.
3Com Router 3000 ADSL2+ Family Getting Started Guide Connecting the Ground Wire Caution: Properly connect the ground wire before connecting other cables and shorten it as much as possible to prevent the router and the connected device from getting damaged during periods of lightning activities. The grounding screw of the chassis PGND is located on the rear panel. Connect this screw to the earth ground using a ground wire. The grounding resistance must not be greater than 5-ohm.
3Com Router 3000 ADSL2+ Family Getting Started Guide Connecting the Router to a Console Terminal Console cable The console cable has an RJ45 connector at one end and a DB9 (socket) connector at the other end. A A Console cable assembly Connecting the console cable Follow these steps to connect the router to a console terminal: Step 1: Select a console terminal. The console terminal can be either a standard ASCII terminal with an RS-232 serial interface or more commonly, a PC.
3Com Router 3000 ADSL2+ Family Getting Started Guide 3. Safety Information You must read the following safety information before carrying out any installation or removal of components, or any maintenance procedures on the product. WARNING: Warnings contain directions that you must follow for your personal safety. Follow all directions carefully. You must read the following safety information carefully before operation, installation or removal of the unit.
3Com Router 3000 ADSL2+ Family Getting Started Guide Important Safety Information WARNING: Installation and removal of Router 3000 units must be carried out by qualified personnel only. WARNING: The unit must be connected to an earthed power supply to ensure compliance with safety standards. WARNING: Power Cord Set: This must be approved for the country where it is used. U.S.A. and The cord set must be UL-approved and CSA certified. Canada The minimum specification for the flexible cord is: No.
3Com Router 3000 ADSL2+ Family Getting Started Guide L'information de Sécurité Importante AVERTISSEMENT: L'installation et la dépose des unités Router 5000 et 6000 Series doivent être confiées à un personnel qualifié. AVERTISSEMENT: Brancher l'unité à une source de courant mise à la terre pour assurer la conformité aux normes de sécurité.
3Com Router 3000 ADSL2+ Family Getting Started Guide Wichtige Sicherheitsinformationen VORSICHT: Einheiten der Router-Serie 5000 und 6000 dürfen nur von qualifiziertem Fachpersonal installiert bzw. deinstalliert werden. VORSICHT: Das Gerät muß an eine geerdete Steckdose angeschlossen werden, die europäischen Sicherheitsnormen erfüllt. VORSICHT: Der Anschlußkabelsatz muß mit den Bestimmungen des Landes übereinstimmen, in dem er verwendet werden soll.
3Com Router 3000 ADSL2+ Family Getting Started Guide Información de Seguridad Importante ADVERTENCIA: La instalación y retirada de las unidades del Router serie 5000 y 6000 sólo debe llevarla a cabo personal cualificado. ADVERTENCIA: Conecte la unidad a una fuente de alimentación con toma de tierra para garantizar el cumplimiento de las normas de seguridad. ADVERTENCIA: Conjunto de cables eléctricos: Debe estar homologado para el pa's donde se utilice: EE.UU.
3Com Router 3000 ADSL2+ Family Getting Started Guide Importanti Informazioni di Sicurezza AVVERTENZA: Le operazioni di installazione e rimozione delle unità Router 5000 e 6000 Series devono essere eseguite esclusivamente da personale qualificato. AVVERTENZA: Per rispettare gli standard di sicurezza, è necessario collegare l'unità a una fonte di alimentazione dotata di messa a terra.
3Com Router 3000 ADSL2+ Family Getting Started Guide Ważne informacje o zabezpieczeniach OSTRZEŻENIE: Instalacja i demontaż urządzenia Router 5000 series i 6000 series mogą być wykonywane tylko przez wykwalifikowany personel. OSTRZEŻENIE: Urządzenie musi być uziemione lub musi być podłączone do uziemionego źródła zasilania w celu zapewnienia zgodności z wymogami bezpieczeństwa.
3Com Router 3000 ADSL2+ Family Getting Started Guide 15
