HP LaserJet Managed MFP E72425, E72430, E72725, E72730 - Engine Install Guide

ManualsBrandsHP ManualsDesktopsHP LaserJet Managed MFP E72425a

support.hp.com

57.7 kg - 63.0 kg

127.2 lb - 138.9 lb

Engine Install Guide

WARNING: Make sure the work area is free of debris

and the  oor is not slippery or wet.

CAUTION: The printer assembly is heavy.

Fourpeople must lift and install it on the dual

cassette feeder (DCF) (Y1F97A), or the cabinet

stand (Y1G17A).

Note: The picture of this guide may di er from your

machine depending on your model.

HP recommends reviewing

the video before performing

the installation.

1.1 1.2

Unpack and acclimate the printer.

CAUTION: Before the printer is powered on, make sure that the room and equipment are at least 15°C (59°F).

NOTE: Leave the printer on the shipping pallet until it is ready to install on a DCF, or the cabinet stand.

Remove the printer, imaging drum, toner collection unit (TCU), and associated hardware from

the box. After unpacking the printer and supplies, allow them to acclimate for four hours.

NOTE: If the printer and hardware were stored below 0°C (32°F), it may take them longer

to acclimate.

CAUTION: Do not remove the shipping tape or protective packing materials until after the

printer is installed on a DCF, or the cabinet stand.

NOTE: Imaging drum is stored in the output bin area below the automatic document feeder.

Pull the protective clear plastic down to the base of the printer to

allow access to lifting points.

https://www.hp.com/videos/A3install

HP LaserJet Managed MFP E72725, E72730

HP LaserJet Managed MFP E72425, E72430

Summary of content (8 pages)

PAGE 1
HP LaserJet Managed MFP E72725, E72730 HP LaserJet Managed MFP E72425, E72430 57.7 kg - 63.0 kg 127.2 lb - 138.9 lb Engine Install Guide support.hp.com https://www.hp.com/videos/A3install 1 HP recommends reviewing the video before performing the installation. WARNING: Make sure the work area is free of debris and the floor is not slippery or wet. CAUTION: The printer assembly is heavy. Four people must lift and install it on the dual cassette feeder (DCF) (Y1F97A), or the cabinet stand (Y1G17A).
PAGE 2
Prepare the DCF, or the cabinet stand for installation. CAUTION: Use care when lifting. Use proper safe lifting practices. IMPORTANT: Retain two thumbscrews for securing the cabinet stand. 2.2 Position the DCF, or the cabinet stand near the printer. WARNING: Make sure the work area is free of debris and the floor is not slippery or wet. NOTE: If desired, lower the stabilizers to prevent the printer from moving. 2.1 Follow the in-box directions to unpack the DCF, or the cabinet stand.
PAGE 3
4.4 4.5 4.6 Remove the foam packaging material. Carefully remove the strapping tape at the rear of the transfer unit. Open Tray 1 on the right side of the printer, and then remove the foam near the pickup roller. 4.7 4.8 Open Tray 2-3 and remove all tape and foam packaging material. Remove the scanner lock screw and red sticker on the left side of the printer. WARNING: The scanner lock screw must be removed prior to powering on the printer. 5 Install the toner cartridge. 5.1 5.2 5.
PAGE 4
6 Install the imaging unit. CAUTION: Do not open the imaging unit package until it is ready to install. Prolonged exposure to bright light can damage the imaging drum and cause image quality problems. 6.1 6.2 Ensure that the front and right doors are open. The right door retracts the interlock lever allowing the imaging unit to be installed. Remove the imaging unit from the foam packaging and plastic bag. 6.3 6.4 6.5 Remove white protective cover. Do not touch surface of the drum.
PAGE 5
7 Install the toner collection unit (TCU). 7.1 8 Load paper in Tray 2. NOTE: Paper is used to print configuration sheets as needed (Letter or A4). 8.1 8.2 Push down on the blue tab in the back of the tray. At the same time, pinch or squeeze the blue tab in the front of the tray and slide to adjust to the proper paper length. Both tabs are spring-loaded and will lock, once released. 8.3 8.4 Squeeze the sides of the tab, and then slide to adjust the paper width. Load the paper.
PAGE 6
10 Late point differentiation configuration (LPDC) checklist (automatic). CAUTION: The LPDC procedure must be performed by a trained person during the device install, staging or, setup process. NOTE: If no internet connection is available, or the LPDC process is not possible via the network connection, the speed license can be downloaded to a USB flash drive and manually installed. Go to Step 11. NOTE: Wait 24-48 hours from the time the unit is shipped to when the license becomes available in the cloud.
PAGE 7
11 Late point differentiation configuration (LPDC) checklist (manually using USB flash drive). • Make sure that the network cable is disconnected from the printer. • Turn on the main power switch (near the power cord), and then press the power button on the front of the printer to turn the power on. • With an internet-connected PC, open a browser and go to the HP Jet Advantage Management (JAM) Activation site: https://activation.jamanagement.hp.com. • Select the country/region.
PAGE 8
12 Install the model nameplate and barcode label. NOTE: The model nameplates are included in the large box that contained the power cord, tray labels, and other items. 12.1 13 13.1 12.2 12.3 Find the bar code that matches the model nameplate and then install the new bar code label on the inside of the front cover of the printer. Install the nameplate. Install the stabilization blocks. 13.2 © Copyright 2020 HP Development Company, L.P. www.hp.