Maintenance and Service Guide
Table Of Contents
- Product description
- Components
- Illustrated parts catalog
- Removal and replacement procedures preliminary requirements
- Removal and replacement procedures for Customer Self-Repair parts
- Removal and replacement procedures for authorized service provider parts
- Interpreting system validation diagnostic front panel LEDs and audible codes
- Troubleshooting guide
- Resources
- General troubleshooting steps
- Identify the issue
- Analyze the issue
- Resolve the issue
- Verify solution
- Helpful Hints
- Common issues and possible solutions
- Additional information
- Acronyms
- Blinking lights and boot error codes
- Processor not executing code
- BIOS recovery code unable to find valid BIOS recovery image
- Memory module error
- Graphics Controller Error (No Controller)
- Failure - System Board Error
- Intel Trusted Execution Technology (TXT) Error
- Sure Start unable to find valid BIOS Boot Block image
- Sure Start has identified a problem (Manual Recovery Policy Set)
- POST error messages and user actions
- Routine maintenance for performance improvement
- Common blue screen error messages
- Use Windows Debugging Tool
- Display issue: pixel anomalies
- Cable management
- Connector types
- Computer Setup (BIOS), TPM, and HP Sure Start
- Using HP PC Hardware Diagnostics
- Backing up, restoring, and recovering
- Specifications
- Power cord set requirements
- Statement of memory volatility
- Recycling
- Index
Display issue: pixel anomalies
All HP notebook displays adhere to strict quality and reliability specications. A small percentage of display
panels may have minor cosmetic manufacturing anomalies or irregularities such as bright or dark dots in the
viewable area. These cosmetic imperfections are common to all display panel types and are not specic to
any HP model or product line.
All display panel defects should be examined at the highest possible resolution using both the brightest and
darkest possible backgrounds, because some sub-pixel failures may not be readily visible under certain
conditions.
● Type 1: Bright dot on a dark background = Always On
● Type 2: Dark dot on a bright background = Always O
● Combination = in any combination and any color that are always on or o
Use the HP PC Hardware Diagnostics (UEFI) tool to determine numbers of pixels and their distance. HP uses
the following set of criteria when damaged displays are submitted for warranty coverage.
Source: http://support.hp.com/us-en/document/c00035844
Table 8-59 Electrical defect criteria
Panel resolution Accept Reject
Sub-pixel faults
VGA, SVGA, SD, WSVGA, XGA, 720p, SD+, WXGA, HD N ≤ 2 Type 1
N ≤ 2 Type 2
N ≥ 3 Type 1
WXGA+, SXGA+, HD+, SXGA+ N ≤ 3 Type 1
N ≤ 3 Type 2
N ≥ 4 Type 1
WSXGA+, UXGA, FHD, WUXGA N ≤ 4 Type 1
N ≤ 4 Type 2
N ≥ 5 Type 1
QHD, QHD+, WQXGA, UD N ≤ 5 Type 1
N ≤ 5 Type 2
N ≥ 6 Type 1
Electrical defect clusters (defects within a 5x5 pixel block)
Minimum distance between ANY allowable defects (unless otherwise specied) S ≥ 25 mm S < 25 mm
Cluster with 2 or more sub-pixels with sub-pixel faults Not allowed
Dim lines Not allowed
Cross line(s) on/o Not allowed
Horizontal line(s) on/o Not allowed
Vertical line(s) on/o Not allowed
NOTE: All LCD panel defects should be examined at the highest possible resolution using both the brightest
and darkest possible backgrounds, as some sub-pixel failures may not be readily visible under certain
conditions.
NOTE: Contact support for assistance if issues are not listed.
146 Chapter 8 Troubleshooting guide