HP Color LaserJet Enterprise M855 and Flow MFP M880 - Hole Punch Kit Installation Guide

ManualsBrandsHP ManualsDesktopsHP Color LaserJet Enterprise M855xh Printer

AZW84-67902 2/3 Hole Punch Kit

CZ999-67902 2/4 Hole Punch Kit

$:

&=



ZZZKSFRPVXSSRUWFRORUOM0

ZZZKSFRPVXSSRUWFRORUOMƮRZ0)30

/HDHVWRSULPHUR



1 2

Turn the product o, and then disconnect the nishing accessory

from the product.

On the nishing accessory, remove four screws from the latch

lower covers.

NOTE: The booklet maker with hole punch accessory is shown

in these photos, however the procedure is correct for all of the

nishing accessories.

CAUTION

: Exposed sheet metal can have sharp

edges. Be careful when working around

exposed sheet metal.

Lea esto primero

www.hp.com/support/colorljM855

www.hp.com/support/colorljowMFPM880

Summary of content (12 pages)

PAGE 1
AZW84-67902 2/3 Hole Punch Kit CZ999-67902 2/4 Hole Punch Kit $ : &= ZZZ KS FRP VXSSRUW FRORUOM0 ZZZ KS FRP VXSSRUW FRORUOMƮRZ0)30 /HD HVWR SULPHUR www.hp.com/support/colorljM855 www.hp.com/support/colorljflowMFPM880 Lea esto primero CAUTION: Exposed sheet metal can have sharp edges. Be careful when working around exposed sheet metal. 1 2 Turn the product off, and then disconnect the finishing accessory from the product.
PAGE 2
3 4 Before proceeding, take note of the two locator pins on the back side of each cover. These pins must be correctly installed to assure proper alignment of the covers when they are reinstalled. Remove the covers (callout 1) by moving the top of the cover outward to release the positioning pins (callout 2). TIP: As the cover is removed, you might need to reach behind the cover to release the two locator pins on the back side of the cover. 6 5 Remove four screws from the latch assembly.
PAGE 3
10 9 Slightly lift up on the cover to release it, and then remove the cover. 11 Remove one screw from the punch rear cover assembly. 12 Slightly lift up on the cover to release it, and then remove the cover. Open the punch door. 14 13 Pull the punch waste box straight out of the punch assembly to remove it. Raise the punch upper cover, and then open the front door.
PAGE 4
16 15 Remove one screw. Close the punch door, and then remove two screws. 17 18 Remove the cover. Close the punch upper cover. 19 20 Remove two screws. Remove one screw.
PAGE 5
22 21 Slightly raise the front edge of the cover, and then slide the cover towards the rear of the accessory to release it. 23 Remove the cover. 24 Disconnect three connectors (callout 1) on the controller PCA, and then release the wire harnesses from one retainer (callout 2). 25 Remove two screws. TIP: These screws fasten the rear sheet-metal support bracket to the punch assembly. Use the hole provided in the chassis next to the punch controller PCA to gain access to these screws.
PAGE 6
28 27 Remove one screw. Slightly lift up on the punch hole assembly (callout 1), and then disengage the sheet-metal support bracket (callout 2). NOTE: The punch hole assembly is still fastened to the accessory chassis, but you should be able to disengage the support bracket. 30 29 Remove one screw. Lift the assembly up to release it, and then remove the assembly.
PAGE 7
Special installation instructions 2 1 5HDU VLGH 3DSHU IHHG GLUHFWLRQ Reconnect the finishing accessory to the product. Turn the power on. After the product has initialized, send a hole punch print job to the accessory. Check the printed page and verify that the holes are punched in the correct page location. )URQW VLGH Punch adjustment is required when the punch holes are misaligned. If the holes are not aligned, identify in which direction the punched hole adjustment is required.
PAGE 8
5 6 Set the punch hole assembly type. Two types of punch hole assemblies are available: the 2/3 punch hole assembly (part number A2W94-67901), or the 2/4 punch hole assembly (part number CZ999-67902). Refer to the part number on the replacement part to determine the type of assembly you are installing. Follow the steps below to set the punch hole assembly type. Turn the product off. 7 8 2 1 3 ON 4 1 2 3 4 5 Set SW601 to the settings above.
PAGE 9
10 LED601 LED602 Blinking one time Not applicable Blinking two times 2/3 punch hole assembly selected Blinking three times 2/4 punch hole assembly selected Blinking four times Waiting for type setting completion Not lit Type setting completed Blinking steadily 11 LED blinking pattern explanation Turn the product off. Follow these steps to set the punch hole assembly type. a. Press SW602 and observe the blinking pattern of LED601 and LED602.
PAGE 10
13 Set the sensor adjustment values. Follow the steps below to adjust the sensors on the punch controller PCA. 14 Make sure that the product power is off. 15 16 2 1 3 ON 4 1 2 3 4 5 Set SW601 to the settings above. Locate the switches and LEDs on the punch controller PCA. • • • • • SW601 (callout 1) LED602 (callout 2) LED601 (callout 3) SW602 (callout 4) SW603 (callout 5) NOTE: SW601 has four electronic switches that can be configure in the ON or OFF position.
PAGE 11
18 LED601 LED602 LED blinking pattern explanation Solidly lit Blinking steadily Adjusting sensors Blinking alternately Waiting for adjustment completion Not lit Sensor adjustment completed Blinking steadily 19 Turn the product off. Follow these steps to adjust the sensors on the punch controller PCA. a. Press SW602 and observe the blinking pattern of LED601 and LED602. The table above explains the different blinking patterns. b.