Upgrade and Service Guide

ManualsBrandsHP ManualsDesktop PCsHP All-in-One 200-5100t CTO Desktop PC

599977-001 i

Printed in

Upgrading and Servicing Guide

Removing the Stand for Wall Mounting ...........2

Before You Begin................................................. 2

Computer Preparation .......................................... 2

Removing the Stand ............................................. 3

Removing and Replacing a CD/DVD Drive .......6

Before You Begin................................................. 6

Computer Preparation .......................................... 6

Removing the CD/DVD Drive................................ 7

Installing a New CD/DVD Drive............................ 8

Removing and Replacing a Hard Disk Drive ..12

Before You Begin............................................... 12

Computer Preparation ........................................ 12

Removing the Hard Disk Drive............................. 13

Installing a New Hard Disk Drive ........................ 14

Upgrading or Replacing Memory ..................18

Before You Begin............................................... 18

Computer Preparation ........................................ 18

Removing the Memory........................................ 19

Installing a New Memory Card............................ 20

Troubleshooting ................................................. 21

Removing and Replacing a Computer Stand ..24

Before You Begin............................................... 24

Computer Preparation ........................................ 24

Removing the Stand ........................................... 25

Installing a New Stand ....................................... 26

Summary of content (28 pages)

PAGE 1
Printed in Upgrading and Servicing Guide Removing the Stand for Wall Mounting ...........2 Before You Begin................................................. 2 Computer Preparation .......................................... 2 Removing the Stand ............................................. 3 Removing and Replacing a CD/DVD Drive .......6 Before You Begin................................................. 6 Computer Preparation .......................................... 6 Removing the CD/DVD Drive ...........
PAGE 2
ii 599977-001
PAGE 3
Removing the Stand for Wall Mounting
PAGE 4
Removing the Stand for Wall Mounting 5-10 minutes The computer can be mounted on a wall by attaching a wall-mounting device (sold separately) to the back of the computer. The four mounting holes on the back of the computer are compliant with the VESA 100 mm spacing standard for mounting compatible devices. Before you can install the wall-mounting device, you need to remove the stand. 2 Press the power button to turn off the computer.
PAGE 5
Lay the computer down on a flat surface, covered with a soft cloth to protect the screen from scratches or other damage. 8 Use a screwdriver to remove the four screws holding the stand. Removing the Stand 9 Slide the stand assembly forward slightly, toward the top of the computer. 6 Remove the back cover above the stand at the back of the computer. Insert a flathead screwdriver or other object with a flat tip into the slot to pry it off.
PAGE 6
11 Use a flathead screwdriver to remove the plastic tabs covering the two screw holes on the back cover. 14 There are four holes for screws to be used to attach the wall mounting device to the computer. 12 Use a flathead screwdriver to remove the plastic tabs covering the two screw holes below the back cover. 15 Follow the wall-mounting hardware manufacturer’s instructions on how to wall-mount the computer. 13 Replace the back cover on to the computer.
PAGE 7
Removing and Replacing a CD/DVD Drive
PAGE 8
Removing and Replacing a CD/DVD Drive 10 - 15 minutes Before You Begin 2 Press the power button to turn off the computer. Observe the following requirements before removing and replacing the hard disk drive. Tools Needed  Flathead screwdriver  Phillips screwdriver #1 CAUTION: Static electricity can damage the electronic components inside the computer. Discharge static electricity by touching the metal cage of the computer before touching any internal parts or electronic components.
PAGE 9
5 Lay the computer down on a flat surface, covered with a soft cloth to protect the screen from scratches or other damage. Removing the CD/DVD Drive 8 Slide the side cover off the computer in the direction indicated by the arrow. 9 Markings on the CD/DVD drive cover indicate the location of the screw. 6 Remove the back cover above the stand at the back of the computer. Insert a flathead screwdriver or other object with a flat tip into the slot to pry it off. 10 Remove the screw for the CD/DVD drive.
PAGE 10
11 Insert a finger, or a screwdriver, in the slot and push the CD/DVD drive out. Installing a New CD/DVD Drive NOTE: The replacement CD/DVD drive may not look exactly the same as the original drive due to different manufacturers or models. Hewlett-Packard always provides quality parts that meet or exceed your original computer specifications. 1 Slide the replacement CD/DVD drive into the computer, placing the notched edge toward the top of the computer. 12 Slide the CD/DVD drive out of the computer.
PAGE 11
4 Replace the side cover. 8 Reconnect all the cables. 5 Replace the back cover above the stand. 6 Place the computer in an upright position. 7 Plug in the power cord.
PAGE 12
10 599977-001 — Removing and Replacing a CD/DVD Drive
PAGE 13
Removing and Replacing a Hard Disk Drive
PAGE 14
Removing and Replacing a Hard Disk Drive 10 - 15 minutes Before You Begin 2 Press the power button to turn off the computer. Observe the following requirements before removing and replacing the hard disk drive. IMPORTANT: A hard disk drive is extremely sensitive to shock impact. Do not bang or drop it. Do not touch the circuit board. Static electricity can damage the drive.
PAGE 15
5 Lay the computer down on a flat surface, covered with a soft cloth to protect the screen from scratches or other damage. Removing the Hard Disk Drive 8 Slide the side cover off the computer in the direction indicated by the arrow. 9 Markings on the lower portion of the computer indicate the location of the screw for the hard disk drive. 6 Remove the back cover above the stand at the back of the computer. Insert a flathead screwdriver or other object with a flat tip into the slot to pry it off.
PAGE 16
11 Grasp the metal handle on the hard disk drive cage to slide the cage in the direction indicated by the arrow on the cage. 14 Slide the hard disk drive out of the cage. 12 Lift out the hard disk drive. Installing a New Hard Disk Drive NOTE: The replacement hard drive may not look exactly the same as the original drive due to different manufacturers or models. Hewlett-Packard always provides quality parts that meet or exceed your original computer specifications.
PAGE 17
2 Slide the replacement hard disk drive into the cage. 5 Tighten the screw. 3 Replace the four screws on the hard disk drive cage. 6 Replace the side cover. 4 Grasp the cage by the handle and slide the hard disk drive back into the hard disk drive bay until it stops. 7 Replace the back cover above the stand. 8 Place the computer in an upright position.
PAGE 18
9 Plug the power cord. 10 Reconnect all the cables.
PAGE 19
Upgrading or Replacing Memory
PAGE 20
Upgrading or Replacing Memory 10 - 15 minutes Before You Begin 2 Press the power button to turn off the computer. Observe the following requirements before removing and replacing memory cards. Tools Needed  Flathead screwdriver CAUTION: Static electricity can damage the electronic components inside the computer. Discharge static electricity by touching the metal cage of the computer before touching any internal parts or electronic components.
PAGE 21
5 Lay the computer down on a flat surface, covered with a soft cloth to protect the screen from scratches or other damage. Removing the Memory 6 Remove the back cover above the stand at the back of the computer. Insert a screwdriver or other object with a flat tip into the slot to pry it off. 8 Slide the cover off the compute in the direction indicated by the arrow. IMPORTANT: If you are removing both cards, you must remove the upper one before removing the lower one.
PAGE 22
Installing a New Memory Card 4 Replace the side cover. NOTE: The replacement memory card may not look exactly the same as the original drive due to different manufacturers or models. Hewlett-Packard always provides quality parts that meet or exceed your original computer specifications. 1 Orient the new memory card so that the notch on the edge of the card faces forward and is on the right. 5 Replace the back cover above the stand. 2 Holding the card by its edges, slide it all the way into the slot.
PAGE 23
8 Reconnect all the cables. Troubleshooting If the computer displays a memory error after you have turned it back on, check the following: 9 Return the computer to the upright position and turn on the computer.  Turn the computer off and unplug the power cord, then open up the memory compartment and make sure the memory card is firmly seated. To install it correctly, make sure it inserted all the way into the compartment and then push down on it to snap it into place.
PAGE 24
22 599977-001 — Upgrading or Replacing Memory
PAGE 25
Removing and Replacing a Computer Stand
PAGE 26
Removing and Replacing a Computer Stand 5-10 minutes Before You Begin 2 Press the power button to turn off the computer. Observe the following requirements before removing and replacing the computer stand. Tools Needed  Flathead screwdriver  Phillips screwdriver #2 CAUTION: Static electricity can damage the electronic components inside the computer. Discharge static electricity by touching the metal cage of the computer before touching any internal parts or electronic components.
PAGE 27
5 Lay the computer down on a flat surface, covered with a soft cloth to protect the screen from scratches or other damage. 8 Use a screwdriver to remove the four screws holding the stand. Removing the Stand 9 Slide the stand assembly forward slightly, toward the top of the computer. 6 Remove the back cover above the stand at the back of the computer. Insert a flathead screwdriver or other object with a flat tip into the slot to pry it off.
PAGE 28
Installing a New Stand 4 Place the computer in an upright position. 5 Plug in the power cord. 1 Align the slot in the new stand assembly with the tab on the computer. Slide the stand in until it aligns with the four screw holes. 6 Reconnect all the cables. 2 Replace the four screws. 3 Replace the back cover above the stand. Copyright © 2010 Hewlett-Packard Development Company, L.P. The information contained herein is subject to change without notice. Version: 1.