Technical data

Index 5
H
hardware checkout procedures, 4-60 to 4-77
hardware initialization support (HP-UX), 4-38
HP 330/660 MB disk controller board (Model 400s),
removal and replacement procedure, 5-38
HP A1096A, VRX Monochrome graphics control-
ler board, 3-19
HP A1416A, VRX color video board, 3-18
HP A1442A Winchester disk drives, jumper set-
tings, A-10
HP A1443A Winchester disk drives, jumper set-
tings, A-10
HP A1444A Micropolis hard disk drive, jumper set
-
tings, A-11
HP A1447A DAT tape drive, jumper settings, A-14
HP A1448A CD ROM disk drive, A-13
HP A1449A 60 MB tape drive, jumper settings,
A-12
HP parallel interface configuration (HP-UX), C-23
to C-24
HP-HIL, theory of operation, 3-11
HP-IB bus interface, 3-10
HP-IB configuration (HP-UX), C-18
HP-IB controller, 3-17
HP-IB interface, 3-14
removal and replacement
Model 400s, 5-50
Model 400t and 400dl, 5-9
HP-UX systems
auto system select mode, C-25 to C-30
boot mode selection, C-9 to C-12
boot ROM
displayed status messages, 4-46
functions, 4-32 to 4-37
messages, 4-46 to 4-49
failure messages, 4-48
self tests, 4-38 to 4-52
booting over the LAN, 4-36 to 4-37
ce.utilities, checkout procedure, 4-74 to 4-76
configuration control mode, C-7 to C-12
configuring internal interfaces, C-24 to C-25
configuring the EEPROM, C-1 to C-30
continuous self tests, 4-53
display types, 4-32
EEPROM configurations, C-3 to C-7
entering I/O configuration mode, C-12 to
C-15
extended SCSI test messages, 4-51, 4-52
extended self tests, 4-54
FRU self test support, 4-38 to 4-40
hardware initialization support, 4-38
HP parallel interface configuration, C-23,
C-24
HP-IB configuration, C-18
human interfaces, 4-34 to 4-36
I/O configuration mode, C-12 to C-25
input devices, 4-35 to 4-36
interface menu, C-15 to C-17
keyboard as system console, setting with
EEPROM configuration, C-3 to C-4
LAN boot error messages, 4-37
LAN configuration, C-22 to C-23
monitor as system console, setting with
EEPROM configuration, C-3 to C-4
new system initial power-on
boot mode LED patterns, C-7 to C-8
configuration control mode, C-7 to C-19
power-up display, C-8
output devices, 4-34 to 4-35
power-up, 4-33 to 4-34
reconfiguring RS-232 interface to remote
mode, C-5
remote human interface, 4-36
RS-232 configuration, C-19 to C-20
running self tests, 4-59
SCSI
configuration, C-21 to C-22
bus address, C-22
interrupt level, C-21
parity mode, C-21 to C-22
select code, C-21
interface ID, 4-52
testing, 4-50 to 4-52
self test control menu, 4-53 to 4-59
self test diagnostics
failure indications, 4-40 to 4-41
FRU support, 4-38 to 4-40
general description of failure codes, 4-41
to 4-43
state and failure LED codes, 4-44 to 4-45
terminal as system console, setting with
EEPROM configuration, C-4 to C-5
terminal as system console with monitor, set-
ting with EEPROM configuration, C-6 to
C-7
terminal escape sequences, 4-36
test mode, 4-52 to 4-60
testing memory 4-54 to 4-59
troubleshooting, 4-2,4-28 to 4-59
flowcharts, 4-28 to 4-31