Getting Started HP Notebook
© Copyright 2011 Hewlett-Packard Development Company, L.P. Bluetooth is a trademark owned by its proprietor and used by Hewlett-Packard Company under license. Microsoft and Windows are U.S. registered trademarks of Microsoft Corporation. SD Logo is a trademark of its proprietor. The information contained herein is subject to change without notice. The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services.
Safety warning notice WARNING! To reduce the possibility of heat-related injuries or of overheating the computer, do not place the computer directly on your lap or obstruct the computer air vents. Use the computer only on a hard, flat surface. Do not allow another hard surface, such as an adjoining optional printer, or a soft surface, such as pillows or rugs or clothing, to block airflow.
iv Safety warning notice
Table of contents 1 Welcome .......................................................................................................................................................... 1 Finding information ............................................................................................................................... 2 2 Getting to know your computer ..................................................................................................................... 4 Top ....................
Using keypads ................................................................................................................... 25 Using the integrated numeric keypad ................................................................ 25 Using an optional external numeric keypad ...................................................... 26 Using pointing devices .......................................................................................................................
Using a Windows 7 operating system DVD (purchased separately) ................. 56 Windows Vista .................................................................................................................................... 57 Backing up your information .............................................................................................. 57 Performing a recovery .......................................................................................................
viii
1 Welcome ● Finding information After you set up and register the computer, it is important to take the following steps: ● Connect to the Internet—Set up your wired or wireless network so that you can connect to the Internet. For more information, refer to Networking on page 17. ● Update your antivirus software—Protect your computer from damage caused by viruses. The software is preinstalled on the computer and includes a limited subscription for free updates.
Finding information The computer comes with several resources to help you perform various tasks. Resources For information about Setup Instructions poster ● How to set up the computer ● Help to identify computer components Getting Started ● Computer features To access this guide: ● How to connect to a wireless network Select Start > Help and Support > User Guides.
Resources For information about Safety & Comfort Guide ● Proper workstation setup, posture, health, and work habits To access this guide: ● Electrical and mechanical safety information Select Start > Help and Support > User Guides. – or – Select Start >All Programs > HP > HP Documentation. – or – Go to http://www.hp.com/ergo. Worldwide Telephone Numbers booklet HP support telephone numbers This booklet is provided with your computer.
2 Getting to know your computer ● Top ● Front ● Right ● Left ● Display ● Rear ● Bottom Top TouchPad Component (1) 4 Description Left pointing stick button Chapter 2 Getting to know your computer Can be used with the pointing stick and functions like the left button on an external mouse.
Component Description (2) Center pointing stick button Can be used with the pointing stick and functions like the center button on an external mouse. (3) Pointing stick Moves the pointer and selects or activates items on the screen. (4) Right pointing stick button Can be used with the pointing stick and functions like the right button on an external mouse. (5) Right TouchPad button Functions like the right button on an external mouse.
Component (5) (6) (7) Description Wireless light Mute light QuickWeb light ● White: An integrated wireless device, such as a wireless local area network (WLAN) device and/or a Bluetooth® device, is on. ● Amber: All wireless devices are off. ● Amber: Computer sound is off. ● White: Computer sound is on. ● On: The computer is on. ● Off: The computer is off or in Hibernation. NOTE: For more information, refer to “HP QuickWeb” in this guide and to the HP QuickWeb software Help.
Buttons and fingerprint reader Component Description (1) TouchPad on/off button Turns the TouchPad on and off. (2) Power button ● When the computer is off, press the button to turn on the computer. ● When the computer is on, press the button briefly to initiate Sleep. ● When the computer is in the Sleep state, press the button briefly to exit Sleep. ● When the computer is in Hibernation, press the button briefly to exit Hibernation.
Component (5) Description QuickWeb button ● When the computer is off or in Hibernation, press the button to open HP QuickWeb. ● When the computer is in Microsoft Windows, press the button to open the default Web browser. ● When the computer is in HP QuickWeb, press the button to open the default Web browser. NOTE: For more information, refer to “HP QuickWeb” in this guide and to the HP QuickWeb software Help.
Keys Component Description (1) esc key Displays system information when pressed in combination with the fn key. (2) Function keys Execute frequently used system functions when pressed in combination with the fn key. (3) fn key Executes frequently used system functions when pressed in combination with a function key or the esc key. (4) Windows logo key Displays the Windows Start menu. (5) Windows applications key Displays a shortcut menu for items beneath the pointer.
Front Component Description (1) Supports the following digital card formats: Media Card reader ● Secure Digital (SD) Card ● Secure Digital HC (SDHC) Card ● Secure Digital XC (SDXC) Card ● MultiMediaCard (MMC) ● MultiMediaCardplus (MMC+) (2) Display release latch Opens the computer. (3) Wireless light ● White: An integrated wireless device, such as a wireless local area network (WLAN) device and/or a Bluetooth® device, is on. ● Amber: All wireless devices are off.
Right Component (1) Description Audio-out (headphone) jack Produces sound when connected to optional powered stereo speakers, headphones, ear buds, a headset, or television audio. WARNING! To reduce the risk of personal injury, adjust the volume before putting on headphones, earbuds, or a headset. For additional safety information, refer to the Regulatory, Safety and Environmental Notices. NOTE: When a device is connected to the headphone jack, the computer speakers are disabled.
Left Component (1) Description Security cable slot Attaches an optional security cable to the computer. NOTE: The security cable is designed to act as a deterrent, but it may not prevent the computer from being mishandled or stolen. (2) USB 3.0 ports (2) Connects optional USB devices. (3) 1394 port Connects an optional IEEE 1394 or 1394a device, such as a camcorder. (4) Vents (2) Enable airflow to cool internal components.
Display Component Description (1) Turns off the display and initiates Sleep if the display is closed while the power is on. Internal display switch NOTE: The display switch is not visible from the outside of the computer. (2) WLAN antennas (3)* Send and receive wireless signals to communicate with wireless local area networks (WLAN). (3) WWAN antennas (2)* Send and receive wireless signals to communicate with wireless wide-area networks (WWAN). (4) Internal microphones (2) Record sound.
Rear Component Description (1) RJ-11 (modem) jack (select models only) Connects a modem cable. (2) Vents (2) Enable airflow to cool internal components. NOTE: The computer fan starts up automatically to cool internal components and prevent overheating. It is normal for the internal fan to cycle on and off during routine operation. (3) 14 Power connector Chapter 2 Getting to know your computer Connects an AC adapter.
Bottom Component Description (1) Battery bay Holds the battery. (2) SIM slot Supports a wireless subscriber identity module (SIM). The SIM slot is located inside the battery bay. (3) Battery release latch Releases the battery from the battery bay. (4) Accessory battery connector Connects an optional accessory battery. (5) Docking connector Connects an optional docking device. (6) Bottom cover release latch Releases or locks the bottom cover.
Component (9) Description Speakers (2) Produce sound. NOTE: To use the SRS Premium Sound software, select Start > All Programs > SRS Premium Sound. (10) Wireless and memory module compartments and hard drive bay Holds an HP Mobile Broadband Module, HP WLAN Module, the memory modules, and the hard drive.
3 Networking ● Using an Internet service provider (ISP) ● Connecting to a wireless network NOTE: Internet hardware and software features vary depending on computer model and your location. Your computer may support one or both of the following types of Internet access: ● Wireless—For mobile Internet access, you can use a wireless connection. Refer to Connecting to an existing WLAN on page 18 or Setting up a new WLAN network on page 19.
Using an Internet service provider (ISP) Before you can connect to the Internet, you must establish an ISP account. Contact a local ISP to purchase Internet service and a modem. The ISP will help set up the modem, install a network cable to connect your wireless computer to the modem, and test the Internet service. NOTE: Your ISP will give you a user ID and password to access the Internet. Record this information and store it in a safe place.
3. Click the network icon in the notification area, at the far right of the taskbar. 4. Select a network to connect to. 5. Click Connect. 6. If required, enter the security key. Setting up a new WLAN network Required equipment: ● A broadband modem (either DSL or cable) (1) and high-speed Internet service purchased from an Internet service provider (ISP) ● A wireless router (purchased separately) (2) ● Your new wireless computer (3) NOTE: Some modems have a built-in wireless router.
Configuring a wireless router For help in setting up a WLAN, refer to the information provided by your router manufacturer or your ISP. The Windows operating system also provides tools to help you set up a new wireless network. To use the Windows tools to set up your network: ● Windows 7—Select Start > Control Panel > Network and Internet > Network and Sharing Center > Set up a new connection or network > Set up a network. Then follow the on-screen instructions.
4 HP QuickWeb Getting started The HP QuickWeb environment provides a fun and engaging way to perform many of your favorite activities. Your computer is ready to go within seconds of starting QuickWeb, allowing you to rapidly access the Internet, widgets, and communication programs. Simply press the QuickWeb button on your computer, and then start browsing the Internet, communicating with Skype, and exploring other HP QuickWeb programs.
Starting HP QuickWeb ● To start HP QuickWeb, press the QuickWeb button when the computer is off or in Hibernation. The following table explains the different behaviors of the QuickWeb button. Button Bahavior QuickWeb button ● When the computer is off or in Hibernation, opens HP QuickWeb. ● When the computer is in Microsoft Windows, opens the default Web browser. ● When the computer is in HP QuickWeb, opens the default Web browser.
5 Keyboard and pointing devices ● Using the keyboard ● Using pointing devices 23
Using the keyboard Identifying the hotkeys A hotkey is a combination of the fn key (1) and either the esc key (2) or one of the function keys (3). To use a hotkey: ▲ Briefly press the fn key, and then briefly press the second key of the hotkey combination. Hotkey combination Description fn+esc Displays system information. fn+f3 Initiates Sleep, which saves your information in system. The display and other system components turn off and power is conserved.
Hotkey combination Description fn+f8 Displays charge information for all installed batteries. The display indicates which batteries are charging and reports the amount of charge remaining in each battery. fn+f9 Decreases the screen brightness level. fn+f10 Increases the screen brightness level. fn+f11 Activates and deactivates the ambient light sensor. When activated, the ambient light sensor automatically adjusts the display brightness based on the lighting conditions in your environment.
Component Description (2) Integrated numeric keypad Can be used like an external numeric keypad. (3) Num lock light ● On: The keypad function is numeric. ● Off: The keypad function is navigational. Using an optional external numeric keypad Keys on most external numeric keypads function differently according to whether num lock is on or off. (Num lock is turned off at the factory.) For example: ● When num lock is on, most keypad keys type numbers.
Turning the TouchPad off and on To turn the TouchPad off and on, quickly double-tap the TouchPad on/off button/light. NOTE: The TouchPad on/off light is off when the TouchPad is on. Navigating To move the pointer, slide one finger across the TouchPad in the direction you want the pointer to go.
Selecting Use the left and right TouchPad buttons like the corresponding buttons on an external mouse. Using TouchPad gestures The TouchPad supports a variety of gestures. To use TouchPad gestures, place two fingers on the TouchPad at the same time. NOTE: TouchPad gestures are not supported in all programs. To view the demonstration of a gesture: 1. Click the Show hidden icons icon in the notification area, at the far right of the taskbar. 2. Click the Synaptics icon 3.
Scrolling Scrolling is useful for moving up, down, or sideways on a page or image. To scroll, place two fingers slightly apart on the TouchPad, and then drag them across the TouchPad in an up, down, left, or right motion. NOTE: Scrolling speed is controlled by finger speed. NOTE: Two-finger scrolling is enabled at the factory. Pinching/Zooming Pinching allows you to zoom in or out on images or text. ● Zoom in by placing two fingers together on the TouchPad, and then moving them apart.
Rotating Rotating allows you to rotate items such as photos. To rotate, anchor your left forefinger in the TouchPad zone. Move the right forefinger around the anchored finger in a sweeping motion, moving from 12 o’clock to 3 o’clock. To reverse the rotation, move your right forefinger from 3 o’clock to 12 o’clock. NOTE: Rotating must be done within the TouchPad zone. NOTE: Rotating is disabled at the factory. Flicking Flicking allows you to navigate through screens or quickly scroll through documents.
6 Maintenance ● Inserting or removing the battery ● Removing or replacing the bottom cover ● Replacing or upgrading the hard drive ● Replacing a drive in the upgrade bay ● Adding or replacing memory modules ● Using the DreamColor display (select models only) ● Updating programs and drivers Inserting or removing the battery NOTE: For additional information on using the battery, refer to the HP Notebook Reference Guide. To insert the battery: 1.
To remove the battery: CAUTION: Removing a battery that is the sole power source for the computer can cause loss of information. To prevent loss of information, save your work and initiate Hibernation or shut down the computer through Windows before removing the battery. 32 1. Turn the computer upside down on a flat surface, with the battery bay away from you. 2. Slide the battery release latch (1) to release the battery. 3.
Removing or replacing the bottom cover CAUTION: To prevent information loss or an unresponsive system: Save your work and shut down the computer before adding or replacing a memory module or hard drive. If you are not sure whether the computer is off or in Hibernation, turn the computer on by pressing the power button. Then shut down the computer through the operating system.
Replacing the bottom cover Replace the bottom cover after accessing the memory module slot, hard drive, regulatory label, and other components. To replace the bottom cover: 1. Tilt down the bottom cover to align the front edge of the bottom cover near the front edge of the computer (1). 2. Insert the alignment tabs (2) on the rear edge of the bottom cover with the notches on the computer. 3. Slide the bottom cover towards the battery bay until the bottom cover snaps into place. 4.
Replacing or upgrading the hard drive CAUTION: To prevent information loss or an unresponsive system: Shut down the computer before removing the hard drive from the hard drive bay. Do not remove the hard drive while the computer is on, in the Sleep state, or in Hibernation. If you are not sure whether the computer is off or in Hibernation, turn the computer on by pressing the power button. Then shut down the computer through the operating system.
10. Use the plastic tab to lift the hard drive (3) and remove it from the computer. Removing the secondary hard drive To remove the secondary hard drive: 36 1. Save your work and shut down the computer. 2. Disconnect AC power and external devices connected to the computer. 3. Turn the computer upside down on a flat surface, with the secondary hard drive bay toward you. 4. Remove the battery (see Inserting or removing the battery on page 31). 5.
8. Use the plastic tab to lift the hard drive (3) and remove it from the computer. Installing the primary hard drive To install the primary hard drive: 1. Turn the computer upside down on a flat surface, with the primary hard drive bay toward you. 2. Insert the hard drive into the primary hard drive bay at an angle, and then lay the hard drive flat in the hard drive bay (1). 3. Pull the plastic tab (2) towards the center of the computer to engage the hard drive with the connector. 4.
6. Tighten the smart card holder screw (2). 7. Replace the bottom cover (see Replacing the bottom cover on page 34). 8. Insert the battery (see Inserting or removing the battery on page 31). 9. Connect AC power and external devices to the computer. 10. Turn on the computer. Installing the secondary hard drive To install the secondary hard drive: 38 1. Turn the computer upside down on a flat surface, with the secondary hard drive bay toward you. 2.
4. Tighten the hard drive screws (3). 5. Replace the bottom cover (see Replacing the bottom cover on page 34). 6. Insert the battery (see Inserting or removing the battery on page 31). 7. Connect AC power and external devices to the computer. 8. Turn on the computer. Replacing a drive in the upgrade bay The upgrade bay can hold either a hard drive or an optical drive.
7. Remove the bottom cover (see Removing the bottom cover on page 33). 8. Remove the hard drive screws from the upgrade bay. 9. Loosen the upgrade bay screw (1). 10. Using a flat-bladed screwdriver, gently push the tab to release the hard drive (2). 11. Remove the hard drive from the upgrade bay (3). To install a hard drive in the upgrade bay: 1. 40 Turn the computer upside down on a flat surface, with the upgrade bay toward you.
2. Insert the hard drive (1) into the upgrade bay, and then tighten the upgrade bay screw (2). 3. Replace the hard drive screws. 4. Replace the bottom cover (see Replacing the bottom cover on page 34). 5. Insert the battery (see Inserting or removing the battery on page 31). 6. Turn the computer right-side up, and then reconnect AC power and external devices to the computer. 7. Turn on the computer.
Replacing an optical drive CAUTION: To prevent information loss or an unresponsive system: Shut down the computer before removing the optical drive from the upgrade bay. Do not remove the optical drive while the computer is on, in the Sleep state, or in Hibernation. If you are not sure whether the computer is off or in Hibernation, turn the computer on by pressing the power button. Then shut down the computer through the operating system. To remove an optical drive from the upgrade bay: 1. Save your work.
3. Tighten the upgrade bay screw (2). 4. Replace the bottom cover (see Replacing the bottom cover on page 34). 5. Insert the battery (see Inserting or removing the battery on page 31). 6. Turn the computer right-side up, and then reconnect AC power and external devices to the computer. 7. Turn on the computer.
Adding or replacing memory modules The computer has two memory module compartments. One memory module compartment is located underneath the keyboard (primary) and the other is located underneath the bottom cover (expansion). The capacity of the computer can be upgraded by: adding a memory module to the vacant primary memory module slot; adding a memory module to the vacant expansion memory module slot; or by upgrading the existing memory module in the primary memory module slot.
b. Grasp the edge of the memory module (2), and then gently pull the memory module out of the memory module slot. CAUTION: To prevent damage to the memory module, hold the memory module by the edges only. Do not touch the components on the memory module. To protect a memory module after removal, place it in an electrostatic-safe container. 7. Insert a new memory module: CAUTION: To prevent damage to the memory module, hold the memory module by the edges only.
c. Gently press the memory module (3) down, applying pressure to both the left and right edges of the memory module, until the retention clips snap into place. CAUTION: To prevent damage to the memory module, be sure that you do not bend the memory module. 8. Replace the bottom cover (see Replacing the bottom cover on page 34). 9. Insert the battery (see Inserting or removing the battery on page 31). 10. Connect AC power and external devices to the computer. 11. Turn on the computer.
6. Remove the keyboard: a. With the computer upside down, open the display and loosen the keyboard screws (1) on the bottom of the computer. b. Release the keyboard by pressing down on the back of the keyboard in the fan area (2). CAUTION: To prevent damaging the fan and keyboard, do not use excessive force when pressing on the keyboard and avoid contact with the fan blades. Also, be sure and use a screwdriver that will fit comfortably between the fan blades when performing this procedure. c.
7. If you are replacing a memory module, remove the existing memory module: a. Pull away the retention clips (1) on each side of the memory module. The memory module tilts up. b. Grasp the edge of the memory module (2), and then gently pull the memory module out of the memory module slot. CAUTION: To prevent damage to the memory module, hold the memory module by the edges only. Do not touch the components on the memory module.
c. Gently press the memory module (3) down, applying pressure to both the left and right edges of the memory module, until the retention clips snap into place. CAUTION: To prevent damage to the memory module, be sure that you do not bend the memory module. 9. Replace the keyboard: a. Lift up the keyboard and flip it over (1), resting it on the base enclosure. b. Slide the keyboard tabs (2) into the base enclosure slots.
c. Press gently on the keyboard (3) so that it snaps in place. d. Turn the computer upside down, open the display and then tighten the keyboard screws (4) to lock the keyboard into place. 10. Replace the bottom cover (see Replacing the bottom cover on page 34). 11. Insert the battery (see Inserting or removing the battery on page 31). 12. Connect AC power and external devices to the computer. 13. Turn on the computer.
Using the DreamColor display (select models only) Computer models with the HP DreamColor display include the preinstalled HP Mobile Display Assistant software. You can use this program to adjust display color settings such as preset color space, white point/color temperature, and luminance/brightness. ▲ To access Mobile Display Assistant, click the Mobile Display Assistant icon in the notification area, at the far right of the taskbar, or select Start > All Programs > HP > Mobile Display Assistant.
Updating programs and drivers HP recommends that you update your programs and drivers on a regular basis with the latest versions. Go to http://www.hp.com/support to download the latest versions. You can also register to receive automatic update notifications when they become available.
7 Backup and recovery Windows 7 ● Backing up your information ● Performing a system recovery To protect your information, use Windows Backup and Restore to back up individual files and folders, back up your entire hard drive (select models only), create system repair discs (select models only) by using the installed optical drive (select models only) or an optional external optical drive, or create system restore points.
new software and data files, you should continue to back up your system on a regular basis to maintain a reasonably current backup. The system repair discs (select models only) are used to start up (boot) the computer and repair the operating system in case of system instability or failure. Your initial and subsequent backups allow you to restore your data and settings if a failure occurs. You can back up your information to an optional external hard drive, a network drive, or discs.
Using the Windows recovery tools To recover information you previously backed up: 1. Select Start > All Programs > Maintenance > Backup and Restore. 2. Follow the on-screen instructions to recover your system settings, your computer (select models only), or your files. To recover your information using Startup Repair, follow these steps: CAUTION: Using Startup Repair completely erases hard drive contents and reformats the hard drive.
3. If the HP Recovery partition is listed, restart the computer, and then press esc while the “Press the ESC key for Startup Menu” message is displayed at the bottom of the screen. 4. Press f11 while the “Press for recovery” message is displayed on the screen. 5. Follow the on-screen instructions. Using a Windows 7 operating system DVD (purchased separately) To order a Windows 7 operating system DVD, go to http://www.hp.
Windows Vista To protect your information, use the Backup and Restore Center to back up individual files and folders, back up your entire hard drive (select models only), or create system restore points. In case of system failure, you can use the backup files to restore the contents of your computer.
To create a backup using Backup and Restore Center: NOTE: Be sure that the computer is connected to AC power before you start the backup process. NOTE: The backup process may take over an hour, depending on file size and the speed of the computer. 1. Select Start > All Programs > Maintenance > Backup and Restore Center. 2. Follow the on-screen instructions to back up your entire computer (select models only) or your files.
4. Select Repair your computer. 5. Follow the on-screen instructions. NOTE: For additional information on recovering information using the Windows tools, perform a search for these topics in Help and Support. Using f11 recovery tools CAUTION: Using f11 completely erases hard drive contents and reformats the hard drive. All files you have created and any software installed on the computer are permanently removed.
NOTE: 60 This process takes several minutes. 1. If possible, back up all personal files. 2. Restart the computer, and then insert the Windows Vista operating system DVD into the optical drive before the Windows operating system loads. 3. When prompted, press any keyboard key. 4. Follow the on-screen instructions. 5. Click Next. 6. Select Repair your computer. 7. Follow the on-screen instructions.
8 Customer support ● Contacting customer support ● Labels 61
Contacting customer support If the information provided in this user guide, in the HP Notebook Reference Guide, or in Help and Support does not address your questions, you can contact HP Customer Support at: http://www.hp.com/go/contactHP NOTE: For worldwide support, click Contact HP worldwide on the left side of the page, or go to http://welcome.hp.com/country/us/en/wwcontact_us.html. Here you can: ● Chat online with an HP technician.
Labels The labels affixed to the computer provide information you may need when you troubleshoot system problems or travel internationally with the computer: ● Serial number label—Provides important information, including the following: Component (1) Product name (2) Serial number (s/n) (3) Part number/Product number (p/n) (4) Warranty period (5) Model description Have this information available when you contact technical support. The serial number label is affixed inside the battery bay.
9 64 Specifications ● Input power ● Operating environment Chapter 9 Specifications
Input power The power information in this section may be helpful if you plan to travel internationally with the computer. The computer operates on DC power, which can be supplied by an AC or a DC power source. The AC power source must be rated at 100–240 V, 50–60 Hz. Although the computer can be powered from a standalone DC power source, it should be powered only with an AC adapter or a DC power source supplied and approved by HP for use with this computer.
Operating environment Factor Metric U.S.
Index Symbols/Numerics 1394 port, identifying 12 A accessory battery connector, identifying 15 ambient light sensor 13 ambient light sensor, identifying 13 ambient light, hotkey 25 audio-in (microphone) jack 11 audio-out (headphone) jack 11 B Backup and Restore 54 Backup and Restore Center 57, 58 battery bay 15, 63 battery light 10 battery release latch 15 battery, replacing 31 Bluetooth compartment, identifying 15 Bluetooth label 63 Bottom cover release latch, identifying 15 bottom cover, removing or re
K keyboard backlight, hotkey 25 keyboard hotkeys, identifying 24 keypad, external num lock 26 using 26 keypad, integrated numeric 9 keypads, identifying 25 keys esc 9 fn 9 function 9 num lk 9 Windows applications 9 Windows logo 9 memory module compartment, identifying 16 Microsoft Certificate of Authenticity label 63 Mobile Broadband Module, identifying 16 mouse, external setting preferences 26 mute light, identifying 6 L labels Bluetooth 63 HP Mobile Broadband Module 63 Microsoft Certificate of Authentic
V vents, identifying 12, 14, 15 volume keys, identifying 24 volume mute button, identifying 7 W webcam 13 webcam light, identifying 13 webcam, identifying 13 Windows 7 operating system DVD 56 Windows applications key, identifying 9 Windows Backup and Restore 53 Windows logo key, identifying 9 Windows Vista operating system DVD 59 wireless antennas, identifying 13 wireless button, identifying 7 wireless certification label 63 wireless lights 6, 10 wireless network (WLAN), equipment needed 19 wireless netwo
