HP StorageWorks Fabric OS 5.3.0 Release Notes (AA-RWEYD-TE, July 2007)

Denial-of-Service condition affecting X.509 certi ficates verification
(NISCC #729 618) due to SSL vulnerability in OpenSSL. FOS 5.3.0
includes new version of OpenSSL that resolves this.
Fixed per Fabric OS 5.3.0
Incorrect time
in Web Tools Switch Health report.
Fixed per Fabri
c OS 5.3.0
IncorrectF_PortbehaviorwhenRXsideofthecableisdisconnected,
while the TX side is still inserted.
Fixed per Fabric OS 5.3.0
Installation of P KI certificate is delayed on any switch on which
installation is attempted due to timing of the startup function.
Fixed per Fabric OS 5.3.0
The last chara
cter of config uploaded Banner (via “bannerset” CLI
command) will disappear when performing a configupload
followed by c
onfigdownload.
Fixed per Fabric OS 5.3.0
When connected to i10k Director in open mode, an RSCN received
from the i10 k was not immediately forwarded.
Fixed per Fabric OS 5.3.0
When upgrading 4/256 to Fabric OS 5.2.0b from 5.2.0a, both ISL
trunk connections to an edge switch connected to FC4-16IP were lost.
Found in test lab and due to “lab mode” setting, not accessible to
customers.
Fixed per Fabric OS 5.3.0
Counter Ad
dress_err counting inappropriate data.
Fixed per F
abric OS 5.3.0
When assigning IP address to a GE port with no cable connection,
the FC 4-16IP blade incorrectly reports ba ck to iSCSI initiator that
port is valid.
Fixed per Fabric OS 5.3.0
The 4/8 and 4/16 SAN Switches would display “Fan x is not faulty”
messages on boot up after upgrade to Fabric OS 5.2.0x, even
though fans were ok.
Fixed per Fabric OS 5.3.0
Disconn
ecting Rx end of cable on an L_port and leaving the Tx end
unchang
ed results in unexpected behavior.
Fixed per Fabric OS 5.3.0
Access Gateway should handle an IPv6 address in a GMAL payload
IP address in “ag – show” truncated to 16 characters (size of I Pv4
address) depending on size of IP address string for edge switch to
which N_Port attached.
Fixed per Fabric OS 5.3.0
Switchdisable and switchenable on switch that directly
connects to storage will cause the storage to see GLIEN reject error
message.
Fixed per Fabric OS 5.3.0
F_Port count is incorrect in agshow on the 4/32 SAN switch.
Fixe
d per Fabric OS 5.3.0
In CLI, iscsicfg –show/delete ddset –n xxx complains “requested
object doesn’t exist” even though it does exist, due to DD/DDSETs
received from Microsoft iSNS server being in uppercase.
Fixed per Fabric OS 5.3.0
During iSCSI 1024 session stress testing, one port lost multiple
sessions. Even though switchshow –iscsi s howed less than 64
sessions, iSCSI initiator wasn’t able to l og in to the target (out of
resources error).
Fixed per Fabric OS 5.3.0
Incorrect GID_FT response from N ameServer. NameServer assumes
device’s FC4 type is FCP when GID_FT request is sent to the switch
asking for PIDs of type FCP. PID of the sending device is i n correctly
included in the reply list.
Fi
xed per Fabric OS 5.3.0
Unable to merge an upgraded switch with a 4/256 with FC4-48
blade when using domain/port zoning of the upper 32 ports of the
blade. When creating D,P zoning definition using these upper 32
ports on FC4-48 connected to another switch running 5.1.0, the two
switches correctly segment due to zoning conflict. After upgrading
to 5.2.0, switches remain segmented, but segmentation should be
removed.
Fixed per Fabric OS 5.3.0
HP StorageW orks Fabric OS 5.3.0 release notes
23