Model C160 / C180 / C200 / C240 Owner’s Guide HP Part No. A4200-90033 Edition E0997 Printed in U.S.A.
Hewlett-Packard Co. 1997 Printing History First Printing: September 1997 UNIX is a registered trademark in the United States and other countries, licensed exclusively through X/Open Company Limited. NOTICE The information contained in this document is subject to change without notice. HEWLETT-PACKARD MAKES NO WARRANTY OF ANY KIND WITH REGARD TO THIS MATERIAL INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
Contents Preface xi Audience xii Safety and Regulatory Statements xii Release Document(s) xii Related Manuals xiii Revision History xiii Documentation Conventions xiv Problems, Questions, and Suggestions xv 1 Product Information Product Description 3 System Unit Front Panel Controls 5 System Power Switch 5 Power LED 6 System LEDs 6 Audio Controls 7 Storage Device Controls and Features CD-ROM Drive 8 DDS Tape Drive 10 Floppy Disk Drive 12 8 System Unit Rear Panel Connectors 13 Pullout Card 14 Security Loo
Contents SCSI Connectors 19 TOC Button 19 Power Cord Connector 19 Monitors 20 Keyboard 21 Pointing Devices 21 Operating System Overview 22 2 Using Your CD-ROM Drive CD-ROM Drive and CD-ROM Media Descriptions 25 CD-ROM Drive 25 Controls and Features 26 CD-ROM Media 28 Caring for CD-ROM Discs 28 Operating the CD-ROM Drive 29 Loading and Unloading a CD-ROM in the Disc Tray 29 Disc Tray Description 29 Loading a CD-ROM Disc in a Horizontally Mounted Drive 30 Unloading a CD-ROM Disc in a Horizontally Mounte
Contents 3 Using Your Digital Data Storage (DDS) Tape Drive DDS Tape Drive and Data Cassette Descriptions 45 DDS Drive 45 Storage Capacities 45 Controls and Indicators 46 LEDs 47 LED Warning Conditions 48 Data Cassettes 49 Media Life 49 Cleaning the Tape Heads 50 Media Restrictions 50 Setting the Write-Protect Tab on a Data Cassette 51 Operating the DDS Tape Drive 52 Loading and Unloading a Data Cassette 52 Verifying the DDS Tape Drive Operation 53 Using Device Files 54 Archiving Data 55 Writing to a Dat
Contents Using Device Files 64 Formatting a New Diskette 65 Transferring Data To and From a Floppy Diskette 66 Saving Files to a Floppy Diskette 66 Restoring Files from a Floppy Diskette to Your System Listing the Files on a Floppy Diskette 67 For More Information 68 Configuring the Floppy Driver 69 66 Troubleshooting 70 Ordering Information 70 5 Solving Problems Common Problems and Solutions 73 Problems with Powering Up the System 73 Problems Loading and Booting the Operating System Problems with the 8
Contents Declaration of Conformity 3 91 Special Video Configuration Statements 92 For EN55022 or CISPR 22 Applications: For FCC Applications: 92 92 Emissions Regulations 93 Federal Communications Commission (FCC) VCCI Class 2 ITE 94 94 93 Emissions Regulations Compliance 94 Acoustics 94 Regulation On Noise Declaration For Machines -3. GSGV 94 Electrostatic Discharge (ESD) Precautions 95 Safety Statement 96 Laser Safety Statement (U.S.A.
Contents Installing a CD-ROM or a DDS-Format Tape Drive 109 Installing a Floppy Drive 111 Installing a Hard Disk Drive in Position 1 113 Installing a Hard Disk Drive in Position 3 or Position 4 115 Replacing the Storage Tray 118 Configuring a Hard Disk Drive 120 Removing the Main Tray Assembly 122 Replacing the Main Tray Assembly 124 Installing Additional memory 126 Installing the EGRAM (Enhanced Graphics RAM) Module (C160/C180) 130 Installing an EISA, PCI, or GSC Option Board 136 Graphics Adapter Conside
Contents Narrow, Single-ended SCSI Bus Configuration Constraints 159 Fast, Wide, Differential SCSI Bus Configuration Constraints 160 Ultra, Wide-SE SCSI Bus Configuration Constraints 160 Determining SCSI Bus Length 161 Narrow, Single-Ended SCSI Bus Length 161 Fast, Wide Differential SCSI Bus Length 163 Ultra, Wide, Single-Ended SCSI Bus Length 165 Assigning SCSI Device IDs 167 Narrow Single-Ended SCSI Device IDs Ultra, Wide SCSI IDs 170 168 Connecting to the SCSI Ports 172 System SCSI Port Connection
Contents Memory Information Sample 1 Memory Information Sample 2 196 197 Displaying the Status of the System I/O 198 Setting the Auto Boot and Auto Search Flags 199 Displaying and Setting the Security Mode 201 Displaying and Setting the Fastboot Mode 202 Displaying the LAN Station Address 203 Configure and Display LAN Settings 204 Displaying System Information 206 Displaying PIM Information 207 x
Preface This owner’s guide describes how to use your HP 9000 C Class workstation. This manual assumes that you have installed your workstation as described in the C Class Hardware Installation Card.
Audience This guide is intended for HP 9000 Model C160/C180/C200/C240 workstation users. Safety and Regulatory Statements See Appendix A in the back of this manual for safety and regulatory statements that apply to this workstation. Release Document(s) Please refer to the Release Document(s) you received with your system or system software for additional information that we may not have been able to include in this guide at the time of its publication.
Related Manuals Refer to the following manuals for more information: • C Class Hardware Installation Card (A4200-90012) • Using Your HP Workstation (A2615-90003) • Installing and Updating HP-UX (B2355-90050) • Configuring HP-UX for Peripherals (B2355-90053) • HP Visual User Environment User’s Guide (B1171-90079) • Managing Clusters of HP 9000 Computers: Sharing the HP-UX File System (B2355-90038) To order manuals, please contact your local sales office.
Documentation Conventions Unless otherwise noted in the text, this guide uses the following symbolic conventions. user-supplied values Italic words or characters in formats and command descriptions represent values that you must supply. sample user input In examples, information that the user enters appears in color. output Information that the system displays appears in this typeface.
Problems, Questions, and Suggestions If you have any problems, questions, or suggestions with our hardware, software, or documentation, please call 1-800-633-3600 (US & Canada) or contact the HP Response Center for your country.
xvi
1 Product Information 1
Product Information This chapter introduces the HP 9000 Model C160/C180/C200/C240 workstations, including their controls and indicators.
Product Information Product Description Product Description The Model C160/C180/C200/C240 workstations contain the following key features: • Processor Performance 160 MHz (Model C160) 180 MHz (Model C180) 200 MHz (Model C200) 236 MHz (Model C240) • Operating System: Native HP-UX HP-UX 10.20 (Model C160) HP-UX 10.20 (Model C180) HP-UX 10.20 with Additional Core Enhancements (ACE) (Models C200/ C240) • User Interface HP VUE version 3.
Product Information Product Description • Internal Storage Devices Fast, Wide Differential SCSI Hard Disk Drives (C160/C180) or Ultra, Wide Single-Ended (C200/C240) 1-inch Low Profile Drive (up to two) 1.6-inch Full Height Drive (one) Single-Ended SCSI Removable Media CD-ROM Drive or 2.0/4.0 GB, 4-mm DDS Tape Drive 4/8 GB, DDS2 DAT Drive (C200/C240) 12/24 GB, DDS3 DAT Drive (C200/C240) 3.5-inch Floppy Disk Drive (not a SCSI Device) • Standard Network Ethernet IEEE 802.
Product Information System Unit Front Panel Controls System Unit Front Panel Controls Figure 1 shows the location of the system unit front panel controls. Removable Storage Devices Power Switch Power LED System LEDs Mute Volume Headset Mic Figure 1 System Unit Front Panel Controls System Power Switch Use the power switch to power the system unit on and off. NOTICE: There is no need to manually shut down the HP-UX operating system on your workstation before powering it off.
Product Information System Unit Front Panel Controls Power LED The power LED is located on the left side of the front panel on the disk tray. It lights when the system unit power is on and flashes until the OS is booted. Once the OS is booted, the LED remains on without flashing, indicating that a soft shutdown is enabled. System LEDs The Model C160/C180/C200 workstations have four diagnostic LEDs located next to the system power LED.
Product Information System Unit Front Panel Controls Audio Controls Next to the system LEDs are the following audio controls: Headset Jack Accommodates mini-headphones with a 3.5 mm diameter miniature stereo plug. Volume Control Adjusts the audio output volume to the headset or lineout. Mic Jack Accommodates microphones with a 3.5 mm diameter miniature stereo plug. Mute Button Turns off the audio output to line out and speaker only.
Product Information System Unit Front Panel Controls Storage Device Controls and Features The Model C160/C180/C200/C240 workstations allow up to two of the following internal storage devices: CD-ROM drive, DDS tape drive, or floppy drive. The following sections describe the controls and features of these devices. NOTICES: You may not have two of the same type of device. For example, you can have a CD-ROM device and a floppy device, but not two CD-ROMs.
Product Information System Unit Front Panel Controls Table 1 CD-ROM Drive Controls and Features Control/Feature Purpose Busy Indicator Lights during a data access operation and blinks during a data transfer. The indicator blinks initially and then stays lit when there is one of the following: • A defective disc • A disc insertion error (for example, an upside-down disc) • No disc present Eject Button Press to open the disc tray and insert or remove a disc.
Product Information System Unit Front Panel Controls DDS Tape Drive Your DDS tape drive is either a DDS-DC (early or later model) or a DDS-2 tape drive with a 3.5-inch form factor, data compression, and a single-ended SCSI interface. Both drives incorporate data compression capability and are high-capacity, high transfer-rate devices for data storage on tape.
Product Information System Unit Front Panel Controls Tape Clean Tape LED Figure 5 Table 2 Clean/Attention LED Eject Button DDS-2 Drive Controls and Indicators DDS Tape Drive Controls and Features Control/Feature Purpose Eject Button Push the eject button to remove tape cassettes from the drive. Drive LEDs The DDS drive LEDs light and flash to indicate drive status and error conditions.
Product Information System Unit Front Panel Controls Floppy Disk Drive Figure 6 shows the operating controls and features of the floppy drive, and Table 3 describes them. Drive LED Eject Button Figure 6 Floppy Drive Controls and Features Table 3 Floppy Drive Controls and Features Control/Feature Purpose Eject Button Push the eject button to remove floppy diskettes from the drive. Drive LED The floppy drive LED flashes to indicate the drive is in use.
Product Information System Unit Rear Panel Connectors System Unit Rear Panel Connectors This section describes the following connectors on the system unit’s rear panel: NOTICE: • Security loop • Audio connectors • Keyboard and mouse connectors • HP parallel (Centronics) I/O connector • 802.
Product Information System Unit Rear Panel Connectors Power Monitor (C180, C200) TOC LAN-AUI LAN-TP Serial 1 Serial 2 PS/2 Mouse PS/2 Keyboard Monitor (C160/C180) HP Parallel Single-Ended SCSI Fast, Wide SCSI (Ultra Wide Single-Ended C200/C240) Audio Line Out Audio Line In Security Loop Pullout Card Figure 7 System Unit Rear Panel Connectors Pullout Card The pullout card contains serial and model number information along with regulatory agency information.
Product Information System Unit Rear Panel Connectors Audio Connectors The Model C160/C180/C200/C240 workstations have audio input and output capability through external input and output connectors on the rear panel and through an internal speaker. The rear panel contains the Line IN (Stereo line-in) and Line OUT (Stereo line-out) connectors. NOTICE: To maintain compliance with FCC/CISPR B you must use fully shielded, unbalanced audio cables and plugs.
Product Information System Unit Rear Panel Connectors Built-in mono speaker • Audio CODEC Crystal CS4215 Table 4 summarizes the audio electrical specifications for the Model C160/ C180/C200/C240 workstations. Table 4 Audio Electrical Specifications Frequency Response 25-20,000Hz Input Sensitivity/Impedance Line Out 2.0Vpk/47k ohm Microphone 22mVpk/1k ohm Max Output Level/Impedance Line Out 2.8Vpp/47k ohm Headphone 2.75Vpp/50 ohm Speaker 5.
Product Information System Unit Rear Panel Connectors PS/2 Keyboard and Mouse Connectors The PS/2 connectors provide an interface to the system for the keyboard, mouse, and a variety of other pointing devices, such as trackballs. Consult the documentation that accompanies each input device for specific information concerning its use. HP Parallel I/O Connector The 25-pin HP Parallel I/O interface uses Centronics interface protocols to support peripheral devices such as printers and plotters.
Product Information System Unit Rear Panel Connectors Serial Input/Output Connectors There are a variety of pointing devices (mouse or trackball) or peripheral devices that can attach to the Serial Input/Output (SIO) ports on the workstation. Peripheral devices include printers, plotters, modems, and scanners. Consult the documentation that accompanies each peripheral device for specific information concerning its use.
Product Information System Unit Rear Panel Connectors SCSI Connectors Use the SCSI connectors to connect external SCSI devices such as DDS-format tape drives and CD-ROM drives. Consult the documentation that accompanies each SCSI device for specific information concerning its use. Refer to Appendix C of this manual for information about connecting SCSI devices to your workstation. NOTICE: There must ALWAYS be a terminator at both ends of a SCSI bus.
Product Information Monitors Monitors The Model C160/C180 workstations have a graphics controller built-in on the I/O board. The Model C180/C200/C240 workstations have a high-performance graphics card installed in an option slot. The following HP monitors are supported: • 17-inch, 1280x1024 color monitor (A4330) • 20-inch, 1280x1024 color monitor (A4331) Before using your monitor you should become familiar with its controls, connectors, and indicators.
Product Information Keyboard Keyboard The C160/C180/C200/C240 systems use a PS/2 keyboard which connects to the PS/2 interface connector on the rear of your workstation. Pointing Devices The PS/2 connector, the HIL port, or the Serial ports support using an HP three-button mouse, a trackball, or other options as pointing devices. For instructions on using a particular device, see the manual that accompanies the device.
Product Information Operating System Overview Operating System Overview The Model C160/C180 workstations use version 10.20 or later of the HP-UX operating system. The Model C200/C240 workstations require the Workstation Additional Core Enhancements (ACE) for 10.20 HP-UX. Instant Ignition systems (systems with preloaded software) have X-windows and the Hewlett-Packard HP VUE 3.0 graphical user interface installed and configured. Refer to Using Your HP Workstation for more information on Instant Ignition.
2 Using Your CD-ROM Drive 23
Using Your CD-ROM Drive This chapter describes how to use your CD-ROM drive. It is divided into the following sections: NOTICE • CD-ROM drive and CD-ROM media descriptions • Operating the CD-ROM Drive • Mounting and unmounting a CD-ROM disc • Troubleshooting Be sure you read and understand the information on mounting and unmounting CD-ROM discs before you begin using your CD-ROM disc drive.
Using Your CD-ROM Drive CD-ROM Drive and CD-ROM Media Descriptions CD-ROM Drive and CD-ROM Media Descriptions This section describes basic information needed for using the CD-ROM drive and CD-ROM discs. CD-ROM Drive The CD-ROM drive is a random access read-only mass storage device that uses removable CD-ROM discs. The drive supports the ISO 9660 and High Sierra format standards. You can access information from the drive like any other disk drive, except that you cannot write to the drive.
Using Your CD-ROM Drive CD-ROM Drive and CD-ROM Media Descriptions Controls and Features Figure 8 shows and Table 6 describes the operating controls and features of the CD-ROM drives.
Using Your CD-ROM Drive CD-ROM Drive and CD-ROM Media Descriptions Table 6 CD-ROM Drive Operating Controls and Features Control/Feature Purpose Headset Jack You can plug mini-headphones with a 3.5-mm diameter miniature stereo plug into this jack. Volume Control Use the volume control to adjust the audio output volume to the headset jack. Busy Indicator The Busy Indicator lights during a data access operation and blinks during a data transfer.
Using Your CD-ROM Drive CD-ROM Drive and CD-ROM Media Descriptions CD-ROM Media CD-ROM discs are 120 mm (4.7 in.) in diameter, and use one data surface with a capacity of approximately 600 megabytes. The data surface contains pits and flat spots arranged in a continuous spiral track, which is read at a constant speed. You may access files and data stored on a CD-ROM disc, but you may not write files or data to a CD-ROM disc.
Using Your CD-ROM Drive Operating the CD-ROM Drive Operating the CD-ROM Drive This section describes how to perform tasks with your CD-ROM drive. Loading and Unloading a CD-ROM in the Disc Tray This subsection describes how to load or unload a CD-ROM disc in the CDROM drive. Disc Tray Description This CD-ROM is designed to be used in either the horizontal or vertical position, depending on whether your system unit is horizontal or vertical (in the floor stand).
Using Your CD-ROM Drive Operating the CD-ROM Drive Loading a CD-ROM Disc in a Horizontally Mounted Drive This CD-ROM drive has an automatic loading/ejecting feature. To load a disc in the CD-ROM drive, follow these steps: Figure 10 Placing a CD-ROM Disc in a Horizontally Mounted Drive 1 Check that the workstation is powered on. 2 To open the disc tray, press and release the load/eject button on the CD-ROM drive. 3 Be sure the disc holders are held away from the disc by the disc holder retainers.
Using Your CD-ROM Drive Operating the CD-ROM Drive Unloading a CD-ROM Disc in a Horizontally Mounted Drive Perform the following steps to unload a disc from the CD-ROM drive: Figure 11 Removing a CD-ROM Disc From a Horizontally Mounted Drive 1 NOTICE: Press the eject button to eject the disc tray from the drive. If the drive is in use, you must press the eject button for more than one second to eject the disc tray. You must unmount the disc before you eject it from the drive.
Using Your CD-ROM Drive Operating the CD-ROM Drive Loading a CD-ROM Disc in a Vertically Mounted Drive To load a disc in the CD-ROM drive, follow these steps: Disc Holder D Disc Holder C Disc Holder A Disc Holder B Figure 12 Releasing the Disc Holder Retainers 1 32 Make sure the four disc holders are disengaged from the disc holder retainers, as shown in Figure 12.
Using Your CD-ROM Drive Operating the CD-ROM Drive 2 Figure 13 Hold the disc with the label side away from the tray and place the edge of the disc onto disc holders A and B as shown in Figure 13. Placing a CD-ROM Disc in a Vertically Mounted Drive 3 Press down gently against the spring tension of disc holders A and B, and swing the top of the disc in until it is held by disc holders C and D. 4 To close the disc tray, push the front of the disc tray gently towards the drive until it closes by itself.
Using Your CD-ROM Drive Operating the CD-ROM Drive Unloading a CD-ROM Disc in a Vertically Mounted Drive Perform the following steps to unload a disc from the CD-ROM drive: Figure 14 Removing a CD-ROM Disc From a Vertically Mounted Drive 1 NOTICE: Press the eject button to eject the disc tray from the drive. If the drive is in use, you must press the eject button for more than one second to eject the disc tray. You must unmount the disc before you eject it from the drive.
Using Your CD-ROM Drive Operating the CD-ROM Drive Verifying the CD-ROM Drive Operation To verify that your workstation can communicate with the CD-ROM drive, follow these steps: 1 In a terminal window, enter the following command: /usr/sbin/ioscan -d sdisk RETURN After a few moments the ioscan utility lists all of the SCSI I/O devices it could find. The list appears similar to the following: H/W Path Class Description ============================================ bc 8 bc 8/12 ext_bus 8/12.
Using Your CD-ROM Drive Mounting and Unmounting a CD-ROM Disc Mounting and Unmounting a CD-ROM Disc To access information on a CD-ROM disc, you must first mount the disc. This applies to file system information only. If you wish to load a music CD, for example, you would not need to mount the disc. Mounting a disc with file system information on it gives the disc a pathname that allows your workstation to communicate electronically with it.
Using Your CD-ROM Drive Mounting and Unmounting a CD-ROM Disc 4 The System Administration Manager window opens. Double-click on Peripheral Devices ->. 5 The Peripheral Devices window opens. Double-click on Disks and File Systems ->. 6 The Disks and File Systems window opens. Double-click on CD-ROM, Floppy, and Hard Disks. The following screen message appears: Scanning the system’s hardware...
Using Your CD-ROM Drive Mounting and Unmounting a CD-ROM Disc Unmounting a CD-ROM Disc Using SAM Use the following procedure to unmount a CD-ROM disc: NOTICE: Before you unmount a CD-ROM disc, make sure that your working directory (the directory in which a relative path name search begins) is set to some directory other than the one under which the disc was mounted. CAUTION: If you wish to use a CD-ROM disc as a mounted file system, you must mount the CD-ROM disc every time you load it into the drive.
Using Your CD-ROM Drive Mounting and Unmounting a CD-ROM Disc 7 A window with the following message opens: Do you want to remove the disk? Click on Yes. 8 Press the eject button on the CD-ROM drive and remove the CD-ROM disc from the disc tray. Reading the Busy Light The CD-ROM busy light shows the status of the drive during the self test and during activity with the host system. The CD-ROM drive performs the self test when one of the following happens: • You load a disc and close the Disc Tray.
Using Your CD-ROM Drive Mounting and Unmounting a CD-ROM Disc The busy light stays on after the self test when one of the following conditions exist: • A defective disc • A disc insertion error (for example, an upside-down disc) • No disc present The busy light goes off when one of the following conditions exist: • A CD-ROM drive power failure exists. • The drive is idle on the SCSI bus. The busy light flashes during normal activity with the system.
Using Your CD-ROM Drive Troubleshooting Troubleshooting If you have trouble with any of these procedures for using your CD-ROM drive, see Chapter 5 of this book, “Solving Problems.
Using Your CD-ROM Drive Troubleshooting 42
3 Using Your Digital Data Storage (DDS) Tape Drive 43
Using Your Digital Data Storage (DDS) Tape Drive This chapter describes how to use the optional Digital Data Storage (DDS) tape drive. It also describes how to maintain and care for the drive. This chapter provides information on the following: CAUTION: • DDS tape drive and data cassette descriptions • Operating the DDS tape drive • Ordering information Use only data cassettes labeled DDS (Digital Data Storage). Never use audio cassettes labeled DAT (Digital Audio Tape) in your DDS-format drive.
Using Your Digital Data Storage (DDS) Tape Drive DDS Tape Drive and Data Cassette Descriptions DDS Tape Drive and Data Cassette Descriptions This section describes basic information needed for using your DDS tape drive and data cassettes. DDS Drive Your DDS tape drive is either a DDS-DC (early or later model) or a DDS-2 tape drive with a 3.5-inch form factor, data compression, and a narrow single-ended SCSI interface.
Using Your Digital Data Storage (DDS) Tape Drive DDS Tape Drive and Data Cassette Descriptions Controls and Indicators Figure 15, Figure 16, and Figure 17 show the LEDs, and eject button of the DDS-format tape drives.
Using Your Digital Data Storage (DDS) Tape Drive DDS Tape Drive and Data Cassette Descriptions LEDs This section describes the LED codes that are displayed. The two LEDs on the front panels of the DDS drives indicate different activities or problems that occur. Figure 18 lists the LED codes and their meanings for the DDS-DC early model drive. Figure 19 lists the LED codes and their meanings for the DDSDC later model and DDS-2 drives.
Using Your Digital Data Storage (DDS) Tape Drive DDS Tape Drive and Data Cassette Descriptions Tape Clean/ Attention Meaning Key OFF Activity — load or unload Steady Green Steady Amber Activity — read or write Flashing Green Cartridge loaded Figure 19 Any Cleaning needed Any Fault 1/2 sec on, 1/2 sec off Pulsing Amber Fast Flash Green 1/4 sec on 1/4 sec off DDS-DC (Later Model) and DDS-2 Tape Drive LED Display Codes LED Warning Conditions The following sections describe actions to take if th
Using Your Digital Data Storage (DDS) Tape Drive DDS Tape Drive and Data Cassette Descriptions If the LED indicators on your DDS-format drive display the Media Wear (Caution) condition, follow this procedure: 1 Check the system console for any tape error messages. A hard error during a read or write operation may have occurred. 2 Clean the heads with a cleaning cassette (HP92283K) as described in “Cleaning the Tape Heads,” later in this chapter.
Using Your Digital Data Storage (DDS) Tape Drive DDS Tape Drive and Data Cassette Descriptions Cleaning the Tape Heads Clean the heads of your tape drive after every 25 hours of tape drive use or if the Media Wear (Caution) signal is displayed on the LED. NOTICE: Only use HP Cleaning Cassettes (HP92283K) to clean the tape heads. Do not use swabs or other means of cleaning the tape heads. Follow this procedure to clean the tape heads: 1 Insert the cleaning cassette into the drive.
Using Your Digital Data Storage (DDS) Tape Drive DDS Tape Drive and Data Cassette Descriptions Setting the Write-Protect Tab on a Data Cassette You can only store or change information on a data cassette when the writeprotect tab is in the write position. So, before trying to write to the data cassette, make sure that the write-protect tab is in the write position, as shown in Figure 20. Push tab right for write. Push tab left for write-protect.
Using Your Digital Data Storage (DDS) Tape Drive Operating the DDS Tape Drive Operating the DDS Tape Drive This section describes how to perform tasks with your DDS tape drive. Loading and Unloading a Data Cassette Follow these steps to load and unload a data cassette from the DDS tape drive: 1 Insert the data cassette into the drive, as shown in Figure 21. Eject Button Figure 21 Loading and Unloading a Data Cassette 2 Push the data cassette about three quarters of the way into the drive.
Using Your Digital Data Storage (DDS) Tape Drive Operating the DDS Tape Drive Verifying the DDS Tape Drive Operation To verify that your workstation can communicate with the DDS-format tape drive, enter the following: /usr/sbin/ioscan -d stape After a few moments the ioscan utility returns a message similar to the following: H/W Path Class Description ============================================ bc 8 bc I/O Adapter 8/16 ba Core I/O Adapter 8/16/5 ext_bus Built-in SCSI 8/16/5.3 target 8/16/5.
Using Your Digital Data Storage (DDS) Tape Drive Operating the DDS Tape Drive Using Device Files Device files are special files that tell your system which system hardware pathway to use when communicating with a specific device, and what kind of device it is. To determine what device files are available for use with your tape drive, use the following procedure: 1 In a terminal window, enter the following command: sam RETURN 2 The System Administration Manager window opens.
Using Your Digital Data Storage (DDS) Tape Drive Operating the DDS Tape Drive Archiving Data This section describes how to transfer data to and from a DDS-format data cassette (saving and restoring) using the HP-UX tar command and your tape drive’s device file. The tar command allows you to save files to a data cassette, restore files from a data cassette to your system, or list the files on your data cassette.
Using Your Digital Data Storage (DDS) Tape Drive Operating the DDS Tape Drive Restoring Files from a Data Cassette to Your System Use the following instructions to restore files from a data cassette to your system: 1 Load the data cassette into the tape drive. 2 In a terminal window, use cd to change to the directory you want the files to reside in.
Using Your Digital Data Storage (DDS) Tape Drive Operating the DDS Tape Drive Further Command Information For additional information on using tar and a complete list of the command arguments, refer to the tar man page by typing the following: man tar The man utility looks up man pages on the system. You may also communicate with the tape drive with the cpio, ftio, mt, and fbackup commands.
Using Your Digital Data Storage (DDS) Tape Drive Troubleshooting Troubleshooting If you have trouble with any of these procedures for using your DDS tape drive, see Chapter 5 of this book, “Solving Problems.
4 Using Your 3.
Using Your 3.5-Inch Floppy Disk Drive This chapter describes how to perform tasks that allow you to archive to or transfer data from the optional 3.5-inch floppy disk drive. The information is organized into the following sections: NOTICE: • Using the floppy diskette • Operating the floppy drive • Ordering information Some procedures in this chapter require you to log in as root. If you cannot log in as root, contact your system administrator.
Using Your 3.5-Inch Floppy Disk Drive Using the Floppy Diskette Using the Floppy Diskette This section describes basic information needed for using your floppy diskettes. Setting the Write-Protect Tab on a Diskette You can only store or change information on a diskette when the write-protect tab is in the write position. So, before trying to write to the diskette, make sure that the write-protect tab is in the write position, as shown in Figure 22. Push tab up for write. Push tab down for write-protect.
Using Your 3.5-Inch Floppy Disk Drive Using the Floppy Diskette Inserting and Removing a Diskette Follow these steps to insert and remove a diskette from the floppy disk drive: 1 Insert the diskette into the drive, as shown in Figure 23. Eject Button Figure 23 Inserting and Removing a Floppy Diskette 2 Push the diskette into the floppy drive until it clicks into place. 3 To remove the diskette, push the eject button, as shown in Figure 23. Then remove the diskette.
Using Your 3.5-Inch Floppy Disk Drive Operating the Floppy Drive Operating the Floppy Drive This section describes how to perform tasks with your 3.5-inch floppy disk drive. Verifying the Floppy Drive Configuration To verify that your workstation can communicate with the floppy drive, use the ioscan command to see which devices are currently in use on your system.
Using Your 3.5-Inch Floppy Disk Drive Operating the Floppy Drive Using Device Files Device files are special files that tell your system which system hardware pathway to use when communicating with a specific device and what kind of device it is. To determine what device files are available for use with your floppy drive, use the following procedure: 1 In a terminal window, enter the following command: sam RETURN 2 The System Administration Manager window opens. Double-click on Disks and File Systems->.
Using Your 3.5-Inch Floppy Disk Drive Operating the Floppy Drive Formatting a New Diskette You must always format a new floppy diskette with the mediainit utility before using it. To format a new floppy diskette follow these steps: 1 Log in as root. 2 Make sure that the write-protect tab on the floppy diskette is in the write position, as shown in Figure 22. 3 Insert the diskette into the floppy disk drive.
Using Your 3.5-Inch Floppy Disk Drive Operating the Floppy Drive Transferring Data To and From a Floppy Diskette This section describes how to transfer data to and from your floppy diskette (saving and restoring) using the HP-UX tar command with your floppy drive’s device file. The tar command saves files to a floppy diskette, restores files from a floppy diskette, or lists files on a floppy diskette. You need to set the write protect tab to the write position to transfer data to the diskette.
Using Your 3.5-Inch Floppy Disk Drive Operating the Floppy Drive 3 Enter the following command line: tar -xvf devicefile pathname where devicefile is the device file as listed by sam and pathname is the pathname of the file or directory containing files that you want to restore from the diskette. If you don’t specify pathname, everything on the floppy diskette is restored.
Using Your 3.5-Inch Floppy Disk Drive Operating the Floppy Drive For More Information For more information on using tar and a complete list of the command arguments, refer to the tar man page by typing the following in a terminal window: man tar The man utility looks up man pages on the system. You can mount the floppy drive as a file system using the SAM utility. Be sure to unmount the drive before removing it as a file system.
Using Your 3.5-Inch Floppy Disk Drive Operating the Floppy Drive Configuring the Floppy Driver If you reload software or rebuild the Instant Ignition system on your workstation, you need to reconfigure the HP-UX Kernel to add the floppy driver. Use the SAM utility to add the flexible disk driver and build a new HP-UX kernel.
Using Your 3.5-Inch Floppy Disk Drive Troubleshooting Troubleshooting If you have trouble with any of these procedures for using your floppy disk drive, see Chapter 5 of this book, “Solving Problems.” Ordering Information To order Hewlett-Packard micro flexible diskettes for use in your 3.5-inch floppy disk drive, use the following order number: HP-92192X 70 High-Density Micro Flexible Disks (1.
5 Solving Problems 71
Solving Problems This chapter contains information to help you determine what’s wrong with your system when you have problems. If you have a problem that isn’t listed in this chapter, or if your problem persists, contact your designated service representative. When calling for service, always have your system’s model number and serial number ready.
Solving Problems Common Problems and Solutions Common Problems and Solutions The tables in this section list common problems you may encounter with your workstation. The tables also tell you what to do to help solve the problems. Problems with Powering Up the System Table 9 describes possible problems you may encounter when powering up the system and offers solutions. Table 9 Power -up Problems Problem The power LED does not light.
Solving Problems Common Problems and Solutions Problems Loading and Booting the Operating System Table 10 describes possible problems you may encounter when loading and booting the operating system and offers solutions. Table 10 Problems Loading and Booting the Operating System Problem Solution The power LED is lit, and text appears on the screen, but more than two minutes have passed with no sign of system activity. Make sure that all SCSI devices are set to the proper SCSI ID.
Solving Problems Common Problems and Solutions Problems with the 802.3 Network Table 11 describes possible problems you may encounter with the 802.3 network and offers solutions. Table 11 Problems with the 802.3 Network Problem Solution Cannot reach other systems on the network. Applications that rely on the network will not run. Check the network connector on the back of the system unit. Make sure that the network cable or transceiver is fastened securely to the connector.
Solving Problems Common Problems and Solutions Problems Using a Hard Disk Drive Table 12 describes possible problems you may encounter using the hard disk drive and offers solutions. Table 12 Problems Using a Hard Disk Drive Problem The disk drive is not accessible or does not respond. Solution Make sure that all the SCSI devices are set to the proper SCSI ID. (See Appendix C for default SCSI ID settings.) Check that all SCSI devices are correctly cabled. Check that the SCSI bus is correctly terminated.
Solving Problems Common Problems and Solutions Problems Using the CD-ROM Drive Table 13 describes a possible problem you may encounter when you use the CD-ROM drive and offers a solution. Table 13 Problems Using the CD-ROM Drive Problem Solution The CD-ROM drive does not respond to commands. Re-enter the commands and make sure that you have typed them correctly. Make sure that the system can communicate with the drive as described in “Checking the SCSI IDs” in Appendix B.
Solving Problems Common Problems and Solutions Problems Using the DDS Tape Drive Table 14 describes a possible problem you may encounter using the DDS tape drive and offers solutions. Table 14 Problems Using the DDS Tape Drive Problem Solution The DDS tape drive does not respond to commands. Re-enter the commands and make sure that you have typed them correctly. Make sure that you specified the correct device file name for commands that require a device file name.
Solving Problems Common Problems and Solutions Problems Using the Floppy Disk Drive Table 15 describes a possible problem you may encounter using the floppy disk drive and offers a solution. Table 15 Problems Using the Floppy Disk Drive Problem Solution The floppy drive does not respond to commands. Re-enter the commands and make sure that you have typed them correctly. Make sure that you specified the correct device file for commands that require a device file name.
Solving Problems LED Error Codes LED Error Codes This section contains information about the error codes displayed by the LEDs on the system’s front panel. If an error occurs during the power-up diagnostics tests, the diagnostics use the front panel LEDs to display a code for the failing component. Figure 24 shows the location of the system unit’s front panel LEDs. The four amber LEDs indicate system status and error codes. Table 16 shows the LED error codes as they appear on the front panel LEDs.
Solving Problems LED Error Codes Table 16 LED Error Codes LED Value RS-232 Chassis Code Range Description N/A Reserved 7500 No memory found FAULT Likely cause: SIMMs or processor board N/A Reserved FLT 7000-7FFF Memory Error Fault Likely Cause: Memory SIMMs System console will indicate which SIMM pair fault occurred on FLT 1020-4099 Processor board FAULT (includes PDH which could be on I/O board.
Solving Problems LED Error Codes Table 16 LED Error Codes LED Value 82 RS-232 Chassis Code Range Description FLT A088 - A0FF No console/IPL error FAULT N/A Reserved N/A Reserved N/A Reserved N/A Power on value. Indicates processor board fault when this value remains for more than a second following power up.
Solving Problems Dealing with a Boot Failure Dealing with a Boot Failure If your usual boot device (typically a disk) is not responding as it should, you must try to boot from the disk (or another boot device) by selecting it manually. To boot a device manually, follow these steps: 1 NOTICE: Follow the directions in “Accessing the Boot Console Interface,” in Appendix D of this book. Your workstation automatically shuts down the operating system before it terminates the power.
Solving Problems Running System Verification Tests Running System Verification Tests HP-UX uses an online diagnostics product called the Support Tools Manager that allows system operation verfications. Three interfaces are available with the Support Tools Manager: a command line interface (accessed through the cstm command), a menu-driven interface (accessed through the mstm command), and the graphical user interface (accessed through the xstm command).
Solving Problems Running System Verification Tests To access the Support Tools Manager, perform the following steps: 1 At a command line prompt, enter the following: cstm The following message appears: Support Tool Manager Version A.01.00 Type ‘help’ for a list of available commands. CSTM> 2 At the CSTM> prompt, you can enter several commands. To see what commands are available, type the help command.
Solving Problems Running System Verification Tests 86
A Safety and Regulatory Statements 87
Safety and Regulatory Statements This appendix contains safety and regulatory statements pertaining to your C Class workstation.
Safety and Regulatory Statements Declaration of Conformity 1 Declaration of Conformity 1 89
Safety and Regulatory Statements Declaration of Conformity 2 Declaration of Conformity 2 90
Safety and Regulatory Statements Declaration of Conformity 3 Declaration of Conformity 3 91
Safety and Regulatory Statements Special Video Configuration Statements Special Video Configuration Statements The following statements apply only to those applications which include a cable connected to the S-Video connector on the A4248A card. No modification to the regulatory statements is necessary for applications which include cables connected to other connectors on the card but not to the SVideo connector. For EN55022 or CISPR 22 Applications: WARNING: This is a Class A product.
Safety and Regulatory Statements Emissions Regulations Emissions Regulations Federal Communications Commission (FCC) This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules and the Canadian Department of Communications. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Safety and Regulatory Statements Emissions Regulations Compliance VCCI Class 2 ITE Emissions Regulations Compliance Any third-party I/O device installed in HP system(s) must be in accordance with the requirements set forth in the preceding Emissions Regulations statements. In the event that a third-party noncompliant I/O device is installed, the customer assumes all responsibility and liability arising therefrom. Acoustics Regulation On Noise Declaration For Machines -3.
Safety and Regulatory Statements Electrostatic Discharge (ESD) Precautions Electrostatic Discharge (ESD) Precautions Electrostatic charges can damage the integrated circuits on printed circuit boards. To prevent such damage from occurring, observe the following precautions during board unpacking and installation: • Stand on a static-free mat. • Wear a static strap to ensure that any accumulated electrostatic charge is discharged from your body to ground.
Safety and Regulatory Statements Safety Statement Safety Statement This equipment conforms to the following safety standards: • UL 1950 • CSA 950 • IEC 950 • EN 60950 96
Safety and Regulatory Statements Laser Safety Statement (U.S.A. Only) Laser Safety Statement (U.S.A. Only) The CD ROM mass-storage system is certified as a Class-1 laser product under the U.S. Department of Health and Human Services (DHHS) Radiation Performance Standard according to the Radiation Control for Health and Safety Act of 1968. This means that the mass-storage system does not produce hazardous laser radiation.
Safety and Regulatory Statements Warnings and Cautions Warnings and Cautions 98
B Changing Your Workstation’s Hardware Configuration 99
Changing Your Workstation’s Hardware Configuration This appendix describes the procedures to change your workstation’s hardware configuration.
Changing Your Workstation’s Hardware Configuration Checking the SCSI IDs Checking the SCSI IDs To determine which SCSI IDs are currently in use on your system, use the ioscan command in a terminal window: 1 At a command line prompt, enter the following at the prompt: /usr/sbin/ioscan -f After a few moments the ioscan utility lists all of the SCSI I/O devices it could find.
Changing Your Workstation’s Hardware Configuration Checking the SCSI IDs 2 NOTICE: You can find out the SCSI IDs currently in use by looking under the H/W Path heading. The listing 8/16/5 scsi is the built-in SCSI bus controller. For devices connected to the built-in SCSI bus, such as disks, the fourth number is the SCSI ID for that device. For example, the listing 8/16/5.4.0 in the sample device list tells you that there is a SCSI device (a disk) currently using ID 4 on the SCSI bus.
Changing Your Workstation’s Hardware Configuration Preparing Your Workstation Preparing Your Workstation This section describes how to prepare your workstation for changing its configuration. Use the following procedure to prepare your workstation: 1 Power off your workstation by pressing the power button on the front panel. When you press the power button, the workstation automatically shuts down the operating system before it powers off the system.
Changing Your Workstation’s Hardware Configuration Preparing Your Workstation Figure 25 Removing the Floor Stand 6 Lay the system unit on a flat surface, such as a table top. 7 Attach a static-grounding wrist strap to bare metal on the back of the system unit.
Changing Your Workstation’s Hardware Configuration Installing Storage Devices Installing Storage Devices This section describes how to install storage devices in your workstation. Before installing a new storage device, perform the following procedures as described earlier in this appendix: • Checking the SCSI IDs • Preparing your workstation CAUTION: All storage devices are susceptible to mechanical and electrostatic shock.
Changing Your Workstation’s Hardware Configuration Installing Storage Devices Preparing to Install Your Storage Device This section describes information that you need to consider and procedures that you need to perform before installing any storage device. Configuring your Storage Device Table 17 lists the recommended SCSI IDs for internal storage devices. If an existing device already uses one of the suggested IDs, select an alternate ID.
Changing Your Workstation’s Hardware Configuration Installing Storage Devices Figure 26 Storage Tstorage trayray Positions Table 18 Storage Configurations Storage Tray Position 1 Supported Devices Conditions Floppy Drive 1-inch Low Profile Disk Drive 2 CD-ROM DDS-Tape 3 1-inch Low Profile Disk Drive This is the only supported position for a 1.6-inch full height disk drive. 1.
Changing Your Workstation’s Hardware Configuration Installing Storage Devices Storage Device Cable Routing When you install your storage device, be aware of the suggested cable routing paths as indicated in the cable routing label that is affixed to the top of the storage tray. Removing the Storage Tray Perform the following procedure to remove the storage tray from the system unit: NOTE: To prevent injury, remove monitor from system unit before removing storage tray.
Changing Your Workstation’s Hardware Configuration Installing Storage Devices CAUTION: Be sure to support the storage tray from underneath while sliding it out of the system unit.
Changing Your Workstation’s Hardware Configuration Installing Storage Devices 2 From the rear of the storage tray, line up the disk slides on the CD-ROM or DDS tape drive with the position 1slots in the storage tray chassis, and slide it into place, as shown in Figure 29. CD-ROM or DDS Tape Drive Cable Routing Label Figure 29 Installing a CD-ROM or DDS Tape 3 Push the storage device in until the locking tabs snap into place.
Changing Your Workstation’s Hardware Configuration Installing Storage Devices Installing a Floppy Drive Perform the following procedure to install a floppy drive in the storage tray: 1 Figure 30 Remove the disk filler panel from the bottom location of the bezel by using a coin or other flat, blunt object to pry it from the front, as shown in Figure 30. Removing a Disk Filler Panel 2 Reach into the storage bay and locate the power and data cables for the floppy drive.
Changing Your Workstation’s Hardware Configuration Installing Storage Devices 4 From the front of the storage tray, line up the disk slides on the floppy drive with the position 2 slots in the storage tray chassis and slide it into place, as shown in Figure 31. Cable Routing Label Figure 31 Installing a Floppy Drive 5 Push the floppy drive in until the locking tabs snap into place. 6 Proceed to the section entitled Replacing the Storage Tray.
Changing Your Workstation’s Hardware Configuration Installing Storage Devices Installing a Hard Disk Drive in Position 1 Perform the following procedure to install a hard disk drive: 1 Figure 32 Remove the disk filler panel from the bottom location of the bezel by using a coin or other flat, blunt object to pry it from the front, as shown in Figure 32. Removing a Disk Filler Panel 2 Reach into the storage bay and locate the power and data cables for the disk drive.
Changing Your Workstation’s Hardware Configuration Installing Storage Devices Cable Routing Label Figure 33 Installing a Hard Disk Drive in Position 1 5 Push the drive in until the locking tabs snap into place. 6 Snap the disk filler panel into the lower bezel position. 7 Proceed to the section entitled Replacing the Storage Tray.
Changing Your Workstation’s Hardware Configuration Installing Storage Devices Installing a Hard Disk Drive in Position 3 or Position 4 Perform the following procedure to install a hard disk drive in positions 3 or 4 of the storage tray: Figure 34 1 Remove the two retaining screws from the disk interconnect board, as shown in Figure 34. 2 Remove the fan bracket and disconnect the fan cable. Removing the Disk Interconnect Board 3 Disconnect any cables from the disk interconnect board.
Changing Your Workstation’s Hardware Configuration Installing Storage Devices 5 From the rear of the storage tray, line up the disk slides on the hard disk drive with the position 3 or position 4 slots in the storage tray chassis and slide it into place, as shown in Figure 35. Cable Routing Label Figure 35 Installing a Hard Disk Drive 6 Push the storage device in until the locking tabs snap into place. 7 Connect the SCSI data cable and the power cable to the drive.
Changing Your Workstation’s Hardware Configuration Installing Storage Devices 8 Figure 36 Slide the disk interconnect board into the storage tray, as shown in Figure 36. Installing the Disk Interconnect Board 9 Reconnect the user interface cable, fan cable, and the disk drive data and power cables to the disk interconnect board. 10 Replace the fan bracket. 11 Replace the disk interconnect board retaining screws and tighten them firmly, as shown in Figure 36.
Changing Your Workstation’s Hardware Configuration Installing Storage Devices Replacing the Storage Tray 1 Slide the storage tray assembly into the system unit chassis, as shown in Figure 37. Retaining Screw Figure 37 Installing the Storage Tray Assembly 2 Tighten the storage tray retaining screw, as shown in Figure 37. 3 Reconnect the power cords to the system unit, the monitor, and any peripherals. Connect the power cords to the ac wall outlets.
Changing Your Workstation’s Hardware Configuration Installing Storage Devices If you installed a new hard disk drive, proceed to the section entitled “Configuring a Hard Disk Drive.” If you installed a new removable media device, refer to the following chapters for information on using the device: • Chapter 2 - Using Your CD-ROM Drive • Chapter 3 - Using Your Digital Data Storage (DDS) Tape Drive • Chapter 4 - Using Your 3.
Changing Your Workstation’s Hardware Configuration Installing Storage Devices Configuring a Hard Disk Drive This section describes how to add a hard disk drive to your system as a file system using SAM. If you installed a new hard disk drive, follow these instructions to make your new disk usable as a file system. For more information about configuring a hard disk drive, refer to the System Administration Tasks manual. This procedure requires you to log in as root.
Changing Your Workstation’s Hardware Configuration Installing Storage Devices 9 The Set Disk Usage and Options window opens. Select File System and click on OK. 10 The following screen messages appear: Task started. Creating the device file... Modifying “/etc/checklist”... Task completed. Click on OK.
Changing Your Workstation’s Hardware Configuration Removing the Main Tray Assembly Removing the Main Tray Assembly Perform the following steps to remove the main tray assembly: 1 NOTICE: Power off the system, the monitor, and any peripheral devices. Unplug the system unit power cord and the power cord of any peripheral devices from ac wall outlets. Disconnect the power cord from the system unit. There is no need to manually shut down the HP-UX operating system on your workstation before powering it off.
Changing Your Workstation’s Hardware Configuration Removing the Main Tray Assembly 5 Place one hand on the top of the system unit and push, while pulling the handle on the rear panel with your other hand. See Figure 38. 6 Slide the main tray assembly out of the chassis.
Changing Your Workstation’s Hardware Configuration Replacing the Main Tray Assembly Replacing the Main Tray Assembly Perform the following steps to replace the main tray assembly: 1 Align the main tray assembly with the chassis and slide it into place, as shown in Figure 39. Thumb Screws Thumb Screws Figure 39 NOTICE: Replacing the Main Tray Assembly 2 Slide the main tray in until you feel it make contact with the internal connectors.
Changing Your Workstation’s Hardware Configuration Replacing the Main Tray Assembly 5 Reconnect the power cables and any other cables that you disconnected when opening the workstation. 6 Power on the monitor, any peripheral devices, and the system unit.
Changing Your Workstation’s Hardware Configuration Installing Additional Memory Installing Additional Memory Take a moment to read over the following important notes about installing memory. • Before you attempt to install additional memory modules in your C160/C180/ C200 workstation, use the procedure described in Appendix D, “The Boot Console Interface,” to determine the current memory configuration for this workstation. • Read over the steps involved in installing memory modules before you begin.
Changing Your Workstation’s Hardware Configuration Installing Additional Memory Perform the following steps to add memory modules to your workstation. 1 Remove the main tray assembly according to the directions in “Removing the Main Tray Assembly” earlier in this appendix. 2 Use Figure 40 to locate the memory modules on the CPU Assembly.
Changing Your Workstation’s Hardware Configuration Installing Additional Memory 3 Close the ejector tabs on each side of the memory connector to lessen the force needed to seat the memory module. See Figure 41. White Ejector Tab Figure 41 Installing Memory Modules 4 Place the memory module in the connector, lining it up with the guides. Make sure to put the notched end toward the white ejector tab, as shown in Figure 41. 5 Press firmly and evenly on the memory module to ensure that it seats properly.
Changing Your Workstation’s Hardware Configuration Installing Additional Memory 6 Replace the main tray assembly as described in “Replacing the Main Tray Assembly,” earlier in this appendix. To verify that this installation was successful, follow the steps in Appendix D, “The Boot Console Interface,” on displaying memory information. If you have only replaced a faulty memory module, you must issue the pdt clear command in the service menu of the Boot Console Interface.
Changing Your Workstation’s Hardware Configuration Installing the EGRAM (Enhanced Graphics RAM) Module (C160/C180) Installing the EGRAM (Enhanced Graphics RAM) Module (C160/C180) Before installing the EGRAM module, perform the procedure in Removing the Main Tray Assembly on page 122. Perform the following steps to add the EGRAM module to your workstation: 1 Figure 42 Press the release clip and rotate the EISA fan, as shown in Figure 42.
Changing Your Workstation’s Hardware Configuration Installing the EGRAM (Enhanced Graphics RAM) Module (C160/C180) 2 Slide the EISA slider to the side to remove it, as shown in Figure 43. 3 Remove the screw from the EISA retainer and remove it, as shown in Figure 43. EISA Slider EISA Retainer Figure 43 Removing the EISA Slider and Retainer 4 Grasp the option board by the edge with both hands and pull it straight out.
Changing Your Workstation’s Hardware Configuration Installing the EGRAM (Enhanced Graphics RAM) Module (C160/C180) Figure 44 5 Install the standoffs into the EGRAM module, as shown in Figure 44. Push the standoffs into the holes on the module until the clips fully emgage with the board. 6 Align the connector on the EGRAM module with the connector on the I/O board, while aligning the standoffs with the holes in the I/O board. See Figure 44.
Changing Your Workstation’s Hardware Configuration Installing the EGRAM (Enhanced Graphics RAM) Module (C160/C180) 8 Figure 45 Rotating the EISA Fan 9 Figure 46 Make sure that the EISA fan is fully rotated, as shown in Figure 45. Slide the option boards into the slots that they came out of, as shown in Figure 46. Make sure that the hole in each board’s handle aligns with the pin on the back panel.
Changing Your Workstation’s Hardware Configuration Installing the EGRAM (Enhanced Graphics RAM) Module (C160/C180) 10 Press in firmly on both ends of the option board at the same time to make sure that it is firmly seated in the backplane connector. 11 Replace the EISA retainer and its screw, as shown in Figure 47. 12 Replace the EISA slider, as shown in Figure 47.
Changing Your Workstation’s Hardware Configuration Installing the EGRAM (Enhanced Graphics RAM) Module (C160/C180) 13 Rotate the fan back into place, as shown in Figure 48. Push it into the rear panel firmly until the clip snaps into place. Figure 48 Securing the Fan 14 Replace the main tray assembly as described in Replacing the Main Tray Assembly on page 124.
Changing Your Workstation’s Hardware Configuration Installing an EISA, PCI, or GSC Option Board Installing an EISA, PCI, or GSC Option Board Your workstation has 4 option slots, as shown in Figure 49. On C160/C180 workstations, slots 1 and 2 each support either GSC or EISA boards. Slot 3 supports a GSC, EISA, or PCI board. Slot 4 supports a GSC or PCI board. On C200 workstations, slots 1, 2, 3 and 4 each support either GSC or PCI boards. Slot 1 supports a GSC, EISA, or PCI board.
Changing Your Workstation’s Hardware Configuration Installing an EISA, PCI, or GSC Option Board Graphics Adapter Considerations If you are installing a graphics option, read the information in this section first. Special Video Configuration Statements The following statements apply only to those applications which include a cable connected to the S-Video connector on the A4248A card.
Changing Your Workstation’s Hardware Configuration Installing an EISA, PCI, or GSC Option Board Graphics Paths graphics(0) is the built-in 8-plane graphics adapter (C160/C180 only). graphics(1) through graphics(4) are graphics adapters installed in option slots 1 through 4.
Changing Your Workstation’s Hardware Configuration Installing an EISA, PCI, or GSC Option Board Graphics Configuration Restrictions This subsection describes restrictions on the installation and support of graphics adapters. Graphics Displays The system supports only four graphics displays at a time. A “display” is a video output port or connector. For example, the Dual Visualize Enhanced Graphics Card (A4451A) is a dual display card.
Changing Your Workstation’s Hardware Configuration Installing an EISA, PCI, or GSC Option Board Upgrading a C160/180 With an HP VISUALIZE-FX Graphics Adapter When you upgrade a Model C160/180 to use the HP VISUALIZE-FX Graphics Adaptor you also need to upgrade the Model C160/180 power supply. When you upgrade with the HP VISUALIZE-FX A4452A Graphics Adapter you must use the HP VISUALIZE Upgrade Kit, partnumber A4450A.
Changing Your Workstation’s Hardware Configuration Installing an EISA, PCI, or GSC Option Board Installing the Option Board Follow these steps to install a GSC, EISA, or PCI board into your workstation: Figure 50 1 Remove the main tray assembly as described in “Removing the Main Tray Assembly” earlier in this appendix. 2 Press the fan release clip and rotate the fan, as shown in Figure 50.
Changing Your Workstation’s Hardware Configuration Installing an EISA, PCI, or GSC Option Board 4 Remove the EISA slider, as shown in Figure 52. 5 In the desired EISA slot, turn the blank plate’s locking knob counter-clockwise to unlock the plate, as shown in Figure 52. Locking Knob Blank Plate EISA Slider Figure 52 Removing the EISA Slider and Blank Plate 6 Remove the blank plate from the slot, as shown in Figure 52.
Changing Your Workstation’s Hardware Configuration Installing an EISA, PCI, or GSC Option Board 7 Figure 53 Slide the board into the slot, as shown in Figure 53. Make sure that the hole in the board’s handle aligns with the pin on the back panel. Installing an Option Board 8 Press in firmly on both ends of the option board at the same time to make sure that it is firmly seated in the backplane connector.
Changing Your Workstation’s Hardware Configuration Installing an EISA, PCI, or GSC Option Board 9 Figure 54 Replace the EISA retainer and its screw, as shown in Figure 54. Installing the EISA Retainer and EISA Slider 10 Replace the EISA slider, as shown in Figure 54.
Changing Your Workstation’s Hardware Configuration Installing an EISA, PCI, or GSC Option Board 11 Rotate the fan back into place, as shown in Figure 55. Push it into the rear panel firmly until the clip snaps into place. Figure 55 Securing the Fan 12 Replace the main tray assembly as described in “Replacing the Main Tray Assembly” earlier in this appendix.
Changing Your Workstation’s Hardware Configuration Replacing the Battery Replacing the Battery Figure 56 1 Remove the main tray as described in “Removing the Main Tray Assembly” earlier in this chapter. 2 Note the orientation of the battery. Make sure that you put the new battery in place with the positive (+) side facing in the same direction. 3 Lift the clip and slip the battery out of its holder, as shown in Figure 42.
Changing Your Workstation’s Hardware Configuration Replacing the Battery 4 Insert the new battery in the same orientation as the old one. (Use only HP part number 1420-0314 or equivalent.) NOTICE: If you cannot gain access to the battery, you may need to remove an option board. Refer to “Installing an EISA, PCI, or GSC Option Board” earlier in this appendix for information on accessing the option boards. CAUTION: Danger of explosion if battery is incorrectly replaced.
Changing Your Workstation’s Hardware Configuration Changing Your Monitor Type Changing Your Monitor Type Your system ships from the factory preset to use a monitor with a specific resolution and frequency. If you replace your monitor with a different type, you must reconfigure your workstation to support it.
Changing Your Workstation’s Hardware Configuration Changing Your Monitor Type Changing the Console to External Terminal In the event that your console stops displaying to your graphics device, use the following procedure to display to console to an external terminal: 1 Turn system power off. 2 Disconnect the PC keyboard connector from the system rear panel. 3 Connect a serial terminal to the Serial 1 connector (the top serial connector) on the system rear panel. 4 Power on the system.
Changing Your Workstation’s Hardware Configuration Changing Your Monitor Type 150
C SCSI Connections 151
SCSI Connections This appendix provides information about connecting Small Computer System Interface (SCSI) devices to an HP 9000 C160/C180/C200/C240 workstation. It presents the information in the following sections: • SCSI bus differences • SCSI restrictions • Determining SCSI bus length • Assigning SCSI device IDs • Connecting to the SCSI ports The instructions in this chapter assume you are using HP-UX version 9.05 or later operating system with HP VUE version 3.0 or later interface.
SCSI Connections SCSI Bus Differences SCSI Bus Differences A Small Computer Systems Interface (SCSI) bus is an IEEE standard bus for connecting your workstation to internal and external devices (SCSI devices) running at different speeds, singly or in combination. Examples of these SCSI devices are 4-mm DDS-format tape drives, CD-ROM drives, and Winchester hard disk drives.
SCSI Connections SCSI Bus Differences Table 19 Transfer Rate Ultra Wide-SE (C200/C240 only) SCSI Bus Differences Data Bus Width 16 bits Maximum Addresses* 16 Maximum Cable Length 3 meters (9.84 feet) Up to 40 Mbytes per second * Address 7 is reserved for host controller use on all buses.
SCSI Connections SCSI Bus Differences Table 20 SCSI Bus Addresses, ID Numbers, and Arbitration Priorities SCSI ID Number 15 . . . . . . 8 7... ...0 Priority . . . . . . . . 1 . . . . . . . 1 6 . . . . . . . . . 1 . . . . . . 2 5 . . . . . . . . . . 1 . . . . . 3 4 . . . . . . . . . . . 1 . . . . 4 3 . . . . . . . . . . . . 1 . . . 5 2 . . . . . . . . . . . . . 1 . . 6 1 . . . . . . . . . . . . . . 1 . 7 0 . . . . . . . . . . . . . . . 1 8 15 1 . . . . . . . . . . . . .
SCSI Connections SCSI Restrictions SCSI Restrictions This section describes the SCSI restrictions that apply to your workstation in the following areas: • Cables • Connectors and Terminator • SCSI configuration constraints Cables All SCSI devices ship without cables. Only SCSI cables approved by HP can be used to connect your workstation and any SCSI devices. HP offers the following SCSI cables for narrow, single-ended SCSI devices: • K2296 cable with 0.
SCSI Connections SCSI Restrictions CAUTION: SCSI cables approved by HP are designed to function within the SCSI tolerances for HP devices. Use of other cables can result in significant problems with system operation. The narrow, singled-ended SCSI implemented on C160/C180/C200/C240 workstations limits the total cable length of narrow SE SCSI cables to 6 meters (19.6 feet). The fast, wide, differential SCSI definition limits the total cable length of FW SCSI cables to 25 meters (82 feet).
SCSI Connections SCSI Restrictions Connectors and Terminators Any narrow, SE SCSI device connecting to the system must use a 50-pin high-density thumb screw connector on the end connecting to the system board. Any fast, wide differential or ultra, wide-SE SCSI device connecting to the system must use a 68-pin high-density thumb screw connector on both ends.
SCSI Connections SCSI Restrictions SCSI Configuration Constraints You are limited to the number of same-type SCSI devices per system. Before adding another SCSI device, determine if the system can support the additional device.
SCSI Connections SCSI Restrictions CAUTION: Do not mix narrow, single-ended SCSI, fast, wide differential SCSI, or ultra, wideSE SCSI peripherals on the same SCSI bus. Fast, Wide, Differential SCSI Bus Configuration Constraints FWD SCSI does not work with either SE SCSI. Table 22 shows the configuration constraints for each FWD SCSI device type.
SCSI Connections Determining SCSI Bus Length Determining SCSI Bus Length This section helps you to determine the total length of the narrow, singleended SCSI bus, the fast, wide differential SCSI bus and ultra, wide singleended SCSI bus.
SCSI Connections Determining SCSI Bus Length If you have problems, call your designated service representative. Table 24 Bus Length Worksheet for Narrow Single-Ended SCSI Bus SCSI Device Internal SCSI Bus Length meters (feet) System Unit 1.3 (4.3) A2655A 0.3 (1.0) C1520B 0.2 (0.7) C1521B 0.2 (0.7) C1700C 1.1 (3.6) C1701C 0.3 (1.0) C1704C 0.0 (0.0) C1705C 0.0 (0.0) C2213A 1.5 (4.9) C2217T 1.3 (4.3) Device Internal Length meters (feet) 1.3 (4.
SCSI Connections Determining SCSI Bus Length Fast, Wide Differential SCSI Bus Length Follow these instructions to calculate your total bus length for the fast, wide differential SCSI bus on your system, using Table 25. NOTICE: 1 List all of your internal fast, wide differential SCSI devices in the first column. 2 In the third column, write the lengths of the internal fast, wide differential SCSI bus that correspond to your devices.
SCSI Connections Determining SCSI Bus Length If you have problems, call your designated service representative. Table 25 Fast, Wide Differential Device System Unit Fast, Wide Differential SCSI Bus Length Worksheet Internal Fast, Wide Differential SCSI Bus Length meters(feet) Device Internal Length meters(feet) 1.5 (4.9) [1.1 (3.61) C200/C240 only] C3034T 1.0 (3.3) C3035T 1.0 (3.3) C3036T 1.0 (3.
SCSI Connections Determining SCSI Bus Length Ultra, Wide, Single-Ended SCSI Bus Length Follow these instructions to calculate your total bus length for the ultra, wide, single-ended SCSI bus on your system, using Table 26. NOTICE: 1 List all of your internal Ultra, Wide SCSI devices in the first column. 2 In the third column, write the lengths of the internal Ultra, Wide SCSI bus that correspond to your devices.
SCSI Connections Determining SCSI Bus Length If you have problems, call your designated service representative. Table 26 Ultra, Wide SE Device Ultra, Wide Single-Ended SCSI Bus Length Worksheet Internal Ultra, Wide SE SCSI Bus Length meters(feet) System Unit 1.1 (3.61) Device _______ 1.0 (3.3) Device _______ 1.0 (3.3) Device _______ 1.0 (3.
SCSI Connections Assigning SCSI Device IDs Assigning SCSI Device IDs Before assigning a SCSI device ID to your drive, you need to check your existing SCSI device IDs. To determine which SCSI device IDs are available for your device, use the ioscan command in a terminal window: 1 At a command line prompt, enter the following: /usr/sbin/ioscan -f After a few moments, the ioscan utility lists all of the SCSI I/O devices it could find.
SCSI Connections Assigning SCSI Device IDs 2 You can tell which SCSI IDs are currently in use by looking under the H/W Path heading. The listing 8/16/5 scsi is the built-in SCSI bus controller. For devices connected to the built-in SCSI bus, such as disks, the fourth number is the SCSI ID for that device. For example, the listing 8/16/5.4.0 in the sample device list tells you that there is a SCSI device (a disk) currently using ID 4 on the SCSI bus.
SCSI Connections Assigning SCSI Device IDs CAUTION: Do not use SCSI device ID 7 for any device. It is reserved for the built-in SCSI bus controller. Table 27 Narrow Single-Ended SCSI Device IDs SCSI Device Drives Device ID (Address) Number (Only 0 through 6 Available) Internal External Internal System Drives: CD-ROM Drive (if present, uses ID No.2) __________ N/A 4-mm DDS Tape Drive (if present, uses ID No.
SCSI Connections Assigning SCSI Device IDs Fast, Wide Differential SCSI IDs (C160/C180/C200 Upgrades) Before assigning a SCSI device ID to your drive, you need to check your SCSI device IDs. To check which SCSI device IDs are available and assign an ID to your device, follow these instructions which use Table 28. 1 Write in the type of each device currently connected to your system under the heading “Fast, Wide Differential SCSI Device Drives” and each drive’s SCSI device ID under the heading “Device ID.
SCSI Connections Assigning SCSI Device IDs 1 Write in the type of each device currently connected to your system under the heading “Ultra, Wide SE SCSI Device Drives” and each drive’s SCSI device ID under the heading “Device ID.” 2 Add your new drive to the table. 3 Check to see what SCSI device IDs are not used. You may use ID numbers 0 through 6 and 8 through 15 if they are not already in use. If the default ID on your drive does not conflict with any existing drive IDs, use that ID.
SCSI Connections Connecting to the SCSI Ports Connecting to the SCSI Ports This section describes how to connect to the system SCSI ports (narrow single-ended and fast, wide differential or ultra, wide single-ended). System SCSI Port Connection The system contains two (2) SCSI connectors: • System Narrow, Single-Ended SCSI Connector • System Fast, Wide Differential SCSI Connector (C160/C180/C200 upgrade) or Ultra, Wide Single-Ended SCSI Connector (C200/C240) Figure 57 shows the two SCSI connectors.
SCSI Connections Connecting to the SCSI Ports NOTICE: It is necessary to put a terminator on empty SCSI connectors on the backpanel, or the last device connected to the SCSI bus. Terminators are shipped with the system. Do mix Fast, Wide and Ultra, Wide-SE terminators.
SCSI Connections Connecting to the SCSI Ports 174
D The Boot Console Interface 175
The Boot Console Interface This appendix describes the different features of the boot console interface and how to use them.
The Boot Console Interface Boot Console Interface Features Boot Console Interface Features There are times when you want to interact directly with the hardware of your workstation before it boots the operating system. Your workstation provides a menu-driven boot console interface that allows you to perform special tasks, display information, and set certain system parameters, even if the operating system is unavailable.
The Boot Console Interface Boot Console Interface Features ------ Main Menu ----------------------------------------------------Command Description ------- ----------- BOot [PRI|ALT|] Boot from specified path PAth [PRI|ALT|CON|KEY][]Display or modify a path SEArch [DIsplay|IPL] [] Search for boot devices COnfiguration [] Access Configuration menu/commands INformation [] Access Information menu/commands SERvice [] Access Service menu/commands DIsplay
The Boot Console Interface Boot Console Interface Features ------ Configuration Menu -------------------------------------------Command Description ------- ----------- AUto [BOot|SEArch] [ON|OFF] Display or set specified auto flag BootID [] [] Display or modify processor boot ID BootINfo Display boot-related information BootTimer [0 - 200] Seconds allowed for boot attempt CPUconfig {] [ON|OFF] Config/deconfig processor DEfault Set the system to predefined values FastBoo
The Boot Console Interface Boot Console Interface Features ------ Information Menu ---------------------------------------------Command Description ----------- ----------- ALL Display all system information BootINfo Display boot-related information CAche Display cache information ChipRevisions Display revisions of VLSI and firmware COprocessor Display coprocessor information FwrVersion Display firmware version IO Dispay I/O interface information LanAddress Display built-in system LAN add
The Boot Console Interface Boot Console Interface Features ------ Service Menu -------------------------------------------------Command Description ------- ----------- ChassisCodes [] Display chassis codes CLEARPIM Clear (zero) the contents of PIM EepromRead [] {] Read EEPROM locations MemRead [] [a] Read memory locations PDT [CLEAR] Display or clear the Page Deallocation Table PIM [ [HPMC|LPMC|TOC]] Display PIM information BOot [PRI|ALT|] Boot from
The Boot Console Interface Accessing the Boot Console Interface Accessing the Boot Console Interface To access the boot console interface, follow these steps: NOTICE: NOTICES: This procedure should be done by a system administrator. 1 Close any files and applications on your workstation. 2 Press the power switch on the front panel of the system unit. There is no need to manually shut down the HP-UX operating system on your workstation before powering it off.
The Boot Console Interface Booting Your Workstation Booting Your Workstation Usually, you start your workstation by turning it on and waiting for HP-UX to boot automatically. However, you may not always want the usual sequence to occur. For example, you may want to start your workstation from an operating system that is stored on a device that is different from your usual boot device.
The Boot Console Interface Booting Your Workstation Answering yes (y) causes the ISL to be loaded from the specified device. After a short time, the following prompt appears on your screen: ISL> ISL is the program that actually controls the loading of the operating system. By interacting with ISL, you can choose to load an alternate version of the HP-UX operating system. If you do not want ISL to be loaded, you must enter n. For example, if the usual kernel (/stand/vmunix) on your root disk (fwscsi.6.
The Boot Console Interface Searching for Bootable Media Searching for Bootable Media To list devices that contain bootable media, follow the directions in “Accessing the Boot Console Interface” earlier in this appendix, and then type the following at the prompt: Main Menu: Enter command > search ipl The search command searches all buses. The search may turn up more devices than there are lines on your display.
The Boot Console Interface Resetting Your Workstation Resetting Your Workstation To reset your workstation, follow the directions in “Accessing the Boot Console Interface” earlier in this appendix, and then type the following at the prompt: Main Menu: Enter command > reset To reset your workstation to its predefined values, follow the directions in "Accessing the Boot Console Interface" earlier in this appendix, and then type the following at the prompt to access the Configuration Menu: Main Menu: Enter c
The Boot Console Interface Displaying and Setting Paths Displaying and Setting Paths A path is the hardware address of a device that is attached to the I/O system of your workstation. The path command sets the system paths shown in Table 30. The path command sets and displays the hardware address of a specified device attached to the I/O bus of your workstation.
The Boot Console Interface Displaying and Setting Paths The paths are displayed in Mnemonic Style Notation, as shown in Table 31. Table 31 Mnemonic Style Notation I/O Type Specification Format Built-in UWSCSI fwsci.scsi_address.logical_unit_number Built-in FWSCSI fwsci.scsi_address.logical_unit_number Built-in SCSI sescsi.scsi_address.logical_unit_number Optional gscn.scsi_address.logical_unit_number Built-in LAN lan.server_address.init_timeout.
The Boot Console Interface Displaying and Setting the Monitor Type Displaying and Setting the Monitor Type Your system ships from the factory preset to use a monitor with a specific resolution and frequency. If you replace your workstation’s monitor with a different type of monitor, you must reconfigure your workstation to support the new monitor. The Monitor Command The monitor command lets you change your workstation’s graphics configuration.
The Boot Console Interface Displaying and Setting the Monitor Type When a dual display graphics adapter (an adapter which has two video output connectors) is installed, the video connector on the left (when looking at the system from the rear) is graphics(NA) and the video connector on the right is graphics(NB). Where N is the slot number in which the graphics adapter is installed.
The Boot Console Interface Displaying and Setting the Monitor Type Setting the Monitor Type You can set the monitor type for a graphics adapter by entering the following: Configuration Menu: Enter command > monitor graphics(n) tt Where n is the number of the graphics adapter and tt is the monitor type.
The Boot Console Interface Displaying and Setting the Monitor Type To set the monitor type for graphics(0) to monitor type 2, enter the following; Configuration Menu: Enter command > monitor graphics(0) 2 Configuration Menu: Enter command > monitor graphics(0) 2 This will take effect on the next reboot.
The Boot Console Interface Displaying and Setting the Monitor Type Setting the Monitor Type at Power On If you replace your workstation’s monitor with a different monitor type, and do not set the workstation’s graphics parameters by using the monitor command before doing so, you need to perform the following: If your keyboard connects to the PS/2 connector on your system, wait 2 seconds after the Num Lock light flashes near the end of the boot sequence, then press Tab to initiate the automatic monitor sele
The Boot Console Interface Displaying and Setting the Monitor Type Changing the Console to External Terminal In the event that your console stops displaying to your graphics device, use the following procedure to display to console to an external terminal: 1 Turn system power off. 2 Disconnect the PC keyboard connector from the system rear panel. 3 Connect a serial terminal to the Serial 1 connector (the top serial connector) on the system rear panel. 4 Power on the system.
The Boot Console Interface Displaying the Current Memory Configuration Displaying the Current Memory Configuration The following sample screen output using the memory command shows: first, a memory configuration table with properly-installed and configured memory (Sample Output 1); and second, output when a SIMM has been improperly installed (Sample Output 2).
The Boot Console Interface Displaying the Current Memory Configuration Memory Information Sample 1 The following sample shows the memory information when memory modules are properly installed and configured MEMORY INFORMATION MEMORY STATUS TABLE Slot ---0a/b 1a/b 2a/b TOTAL Size(a+b) --------64MB 32MB 128MB --------224MB Status -----Configured Configured Configured DETAILED MEMORY CONFIGURATION TABLE SPA --0x00000000 GROUP ----1 SMC --0 0 0 SMC Status ---------Configured Configured Configured 0x0c00
The Boot Console Interface Displaying the Current Memory Configuration Memory Information Sample 2 The following sample shows the memory information when memory modules are not properly installed and configured. In this sample the memory module in memory slot 1A is missing. MEMORY INFORMATION WARNING: Memory has been reconfigured due to a physical change or because the Page Deallocation Table (PDT) was cleared. This is for information only. No action is required.
The Boot Console Interface Displaying the Status of the System I/O Displaying the Status of the System I/O The IO command lets you identify all built-in I/O devices and optional I/O devices installed in the option slots. It is available in the Information Menu. To use the IO command from the Information Menu of the boot console interface, type: Information Menu: Enter command > IO Information about the built-in and optional I/O devices is displayed.
The Boot Console Interface Setting the Auto Boot and Auto Search Flags Setting the Auto Boot and Auto Search Flags auto boot and auto search are variables stored in your workstation’s nonvolatile memory. (Nonvolatile memory retains its contents even after power is turned off.) If you reset these flags to new value, the change takes effect the next time you reboot the workstation. auto boot boots the operating system whenever your workstation is turned on.
The Boot Console Interface Setting the Auto Boot and Auto Search Flags Autosearch searches for devices in the following order: Primary boot path Alternate boot path Built-in fast, wide SCSI devices (or ultra, wide SCSI on C200/C240) GSC card in slot 1 PCI card in slot 1 GSC card in slot 2 PCI card in slot 2 GSC card in slot 3 PCI card in slot 3 GSC card in slot 4 PCI card in slot 4 Built-in single-ended SCSI devices Built-in LAN bootp servers NOTICE: SCSI adapter option cards installed in the option slots
The Boot Console Interface Displaying and Setting the Security Mode Displaying and Setting the Security Mode The SECure flag is a variable stored in non-volatile memory. (Non-volatilmemory retains its contents even after power is turned off.) If you reset this flag to a new value, the change takes effect the next time you reboot the workstation. When the SECure flag is set to on, autoboot and autosearch are enabled and cannot be stopped.
The Boot Console Interface Displaying and Setting the Fastboot Mode Displaying and Setting the Fastboot Mode When fastboot is enabled (set to on), your workstation does a quick check of the memory and skips I/O interface testing, and processor and cache selftesting during its power-on self tests. This enables your workstation to complete its boot process quicker. The default factory setting is for fastboot to be enabled (on).
The Boot Console Interface Displaying the LAN Station Address Displaying the LAN Station Address It is sometimes necessary to supply a LAN station address of your workstation to other users. For example, if your workstation is to become a member of a cluster, the cluster administrator needs to know your LAN station address in order to add your workstation to the cluster.
The Boot Console Interface Configure and Display LAN Settings Configure and Display LAN Settings The LanConfig command configures and displays the current LAN settings. The C180, C200 and C240 systems support 10Base-T, 100Base-T and AUI standards. To automatically select the network speed (100 Mbits/sec or 10 Mbits/sec) and data transfer operation (full or half duplex), operating in compliance with IEEE 802.
The Boot Console Interface Configure and Display LAN Settings Configuration Menu: Enter command > LanConfig AUI NOTE: The LAN setting defaults to LAN-TP(RJ45). If that setting fails, the system tries the LAN-AUI setting. Also note that the new lan configuration settings take effect at the next BOot or SEArch command.
The Boot Console Interface Displaying System Information Displaying System Information The all command allows you to display the system’s processor revision and speed, cache size, memory size, flag settings, and the boot and console paths. To display system information from the Information Menu, type the following at the prompt: Information Menu: Enter command > all This information is paged to allow you to view it as necessary.
The Boot Console Interface Displaying PIM Information Displaying PIM Information The pim command allows you to display the most recent PIM information for the specified fault type.
The Boot Console Interface Displaying PIM Information 208
Glossary absolute pathname The full pathname of a file, including all the directories leading to it, starting with the root directory (“/”) and ending with the filename itself. See also file, filename, pathname. access permissions Settings that allow a user or group of users to read, write, or execute files. See also file access permissions. active window The window that is receiving input from the keyboard at the present time. If there is no active window, anything you type is lost.
Glossary and flat spots arranged in a continuous spiral track, which is read at a constant speed. CD-ROM drive A random-access, read-only, mass-storage device that uses removable CD-ROM discs. The drive contains a semiconductor laser for reading data optically and an embedded controller with a SCSI interface. Central Processing Unit (CPU) The part of a workstation that interprets and executes instructions. child directory See subdirectory. click To press and release a mouse button.
Glossary key while pressing another key. cpu See Central Processing Unit. CRX color graphics Expanded graphics capability offering 24-plane color, 24-plane Z-buffered color, or 48-plane Z-buffered color capability. current directory See current working directory. current session The work and processes that have been created since you logged into the system (and before you log out again). See also session.
Glossary stations. A diskless workstation boots from its partner workstation. See also disked workstation, node, partner node, workstation. ETHERNET The LAN developed jointly by Digital Equipment Corporation, Intel, and Xerox Corporation, upon which the IEEE 802.3 network is based. double click To press and release a mouse button twice in rapid succession.
Glossary file server A workstation whose primary task is to control the storage and retrieval of data from hard disks. Any number of other workstations can be linked to the file server in order to use it to access data. $HOME The environment variable representing the home directory. This is the directory in which you are placed after you log in. Typically, this is /users/ login, where login is your username. See also home directory. file system The organized set of files and directories on a hard disk.
Glossary iconize To turn a window or shell into an icon. See also icon. LAN station address See local area network station address. Initial System Loader The program that actually controls the loading of the operating system. link n. A special object that contains the name of another object. When you specify a link as a pathname or part of a pathname, the system substitutes the pathname that the link contains.
Glossary menu bar An area at the top or bottom of a window that contain the titles of the pull-down or pop-up menus for that application. minimize button In HP VUE, a push button on the window frame that turns a screen into an icon. See also icon, iconize. mouse pointer See pointer. name A character string associated with a file, directory, or link. A name can include various alphanumeric characters, but never a slash (/) or null character. See also pathname.
Glossary path The hardware address of a device that is attached to the I/O system of your workstation. pathname A series of names separated by slashes that describe the path of the operating system from some starting point in the network to a destination object. Pathnames begin with the name of the starting point, and include every directory name between the starting point and the destination object. A pathname ends with the name of the destination object. See also name, object.
Glossary give the system to execute a utility program or shell script. See also shell script, utility program. shell script A file that contains commands that the system can interpret and run in a shell. shutdown The process of taking the system from multi-user state to system administration state. SIMM See Single In-line Memory Module. single-ended standard SCSI An 8-bit wide SCSI bus with standard receivers and drivers, which limits total cable length to 6 meters.
Glossary non-client programs into believing they are running in their favorite terminal. When not running programs or executing operating system commands, terminal windows display the command-line prompt. See also HP Visual User Environment. recognizes as uniquely yours. Also known as your login name. The username is also the name that identifies you to the mail system and other software requiring secure entry.
Glossary eration of windows on the HP VUE Workspace. The Workspace Manager is a special Window Manager. See also Window Manager. workstation A compact, graphics-oriented computer having high speed and high memory capacity. A workstation usually includes a keyboard, a monitor, and a system unit. See also node, disked workstation, diskless workstation.
Glossary 220
Index Symbols $HOME,, 213 A absolute pathname,, 209 access permissions,, 209 active window,, 209 ANSI,, 209 archiving data listing files,, 56 restoring files,, 56 saving to a cassette,, 55 archiving data,, 55 argument,, 209 attachment unit interface (AUI),, 209 audio CODEC, 16 features, 15 headphone jack, 7 IN,, 14 input, 15 microphone jack, 7 mute button, 7 OUT,, 14 outpu, 15 volume control, 7 auto boot,, 199 auto boot, changing state,, 199 auto search,, 199 auto search, changing state,, 199 auto-negotiat
Index double click,, 212 drag,, 212 drive,, 212 drop,, 212 operating,, 63 verifying configuration,, 63 floppy drive,, 213 floppy driver configuring,, 69 E EISA option board installing,, 136 EISA slots displaying status,, 198 EISA,, 212 electrostatic discharge (ESD) precatuions,, 95 emissions regulations Federal Communications Commission (FCC),, 93 third party compliance,, 94 environment variables,, 212 environment,, 212 ETHERNET,, 212 F fast, differential SCSI,, 212 fastboot disabling,, 202 displaying st
Index data cassettes,, 58 diskettes,, 70 output device,, 215 output window,, 215 P parent directory,, 215 partner node,, 215 password,, 215 path displaying,, 187 setting,, 188 path,, 187, 216 pathname,, 216 permissions,, 216 PID,, 216 PIM information,displaying,, 207 pointer,, 216 pointing devices, 21 problems 802.
Index 224