HP LaserJet 3200 Product - Parameter Settings Introduction 프린터의 파라미터 값들을 변경하기 위해서 * 키와 #키를 동시에 누른 후 ENTER 키를 눌러 Developer’ s 메뉴로 들어간다. 프린터의 디스플레이 창에 “ Developer’ s menu/r/w parameter 라는 메시지가 나타나면 ENTER 키를 눌러 이 메뉴안으로 이동한다. 프린터에 설치된 펌웨어의 버전에 따라 디스플레이창 맨아래 줄에 “ LIU ID” 또는 “ param ver code” 등이 나타난다. 아래의 테이블을 참조하여 필요한 파라미터를 찾는다. 그리고 변경할 파라미터의 숫자를 입력한다. 디스플레이 창은 입력한 숫자에 따라 파라미터의 이름이 나타난다. Enter 키를 누르면 현재 설정되어있는 값이 나타난다. 이 기능을 취소하기 위해서 파라미터값이 나타났을 때 STOP/CLEAR 키를 누른다.
MENU: Data store DEVELOPER'S MENU R/W PARAMETER SET: Select parameter R/W PARAMETER >[PARAMETER NAME] SET: Parameter value [PARAMETER NAME] >###### ACK: Parameter setting [PARAMETER NAME] >###### Line interface identification Parameter Description Units 1 u16bit parameter version code. The default value is 1. N/A 2 LIU ID interface code. This value is set by the firmware. The value depends upon which LIU is installed in the unit. N/A Country Default U.S.
LIU COUNTRY is the country code that determines appropriate country specific telecom parameters. This is the country in which the unit is intended to operate.
Ring detection and auto answering Default Parameter Description Units 4 Auto answer enable. Modified by the user through the fax receive setup menu answer mode. If TRUE, the device will automatically answer and attempt to receive a fax after the set number of rings to answer. The default value is true for all countries. 0 = False 1 = True 5 Auto answer ring cadences. Determines the types of rings that are counted.
9 Ring envelope minimum ON time. Minimum time an entire ring signal must be present to be counted as 1 ring. The entire ring signal may consist of several ring bursts separated by periods of silence.
10 Ring envelope maximum ON time. Maximum time an entire ring signal can be present to be counted as 1 ring. The entire ring signal may consist of several ring bursts separated by periods of silence. 1 ms (50 ms to 10000 ms) All countries 8000 11 Ring envelope minimum OFF time. Minimum time between ring envelops, where each ring envelope may consist of a single or multiple rings. Once this time has expired the ring count is incremented.
15 Minimum number of rings. This is the minimum ring count the user can enter. This is used for data entry validation only.
16 Maximum number of rings. This is the maximum ring count that the user can enter. This is used for data entry validation only.
Eavesdrop detection and auto answering Parameter Description Units Country Default 17 Silent detect enable. Incoming faxes are detected through the presence of CNG tone or a sufficient period of silence. If TRUE then silent detection is attempted. Selected by the user from the fax receive setup menu, silence detection. 0 = False 1 = True All countries 0 18 Parallel detect enable. If TRUE, eavesdrop detection is attempted when either a parallel or downstream telephone (or TAM) answers.
27 CNG filter bandwidth. Tone filter bandwidth used for CNG tone detection. 20 = 20 Hz 40 = 40 Hz 60 = 60 Hz 80 = 80 Hz All countries 60 28 CNG sidetone frequencies. Indicates the frequency combination that is used to identify CNG sidetones. 1=1 2=2 3 = 1 and 2 5 = 1 or 2 All countries 3 29 CNG sidetone frequency 1. The presence of sidetones may indicate that the current signal is not a valid CNG signal. 1 Hz (300 Hz to 2100 Hz) All countries 1000 30 CNG sidetone frequency 2.
37 DTMF code third char. Third digit of the DTMF start sequence used to start a fax receive.
38 Off hook delay time. Specifies the minimum time between the completion of an outgoing or incoming call and the automatic dialing of the next outgoing call.
39 Pre OFF hook shunt. Defines the time the LIU shunt will be active. The shunt is activated just as the device goes OFF hook. Not supported by all LIUs.
40 Modem loop current test enable. Controls if a modem loop current test is performed after the LaserJet 3200 has connected to the external line and before automatic dialing is started. If TRUE, the 3200 will test for the presence of loop current after going OFF hook prior to dialing. If loop current is not detected, the fax session is aborted. 0 = False 1 = True All countries 0 41 Modem loop current detection time minimum.
47 48 Obsolete PSTN pre dial pause mode. Specifies what type of pause the LaserJet 3200 will perform before dialing when configured for PSTN operation. If BLIND WAIT, the unit will look for a dial tone and dial immediately if detected, or will dial after the blind dial delay time has elapsed. If CHECK FOR TONE, a PSTN dial tone must be detected before dialing. The value 2 is no longer used. 0 = Blind Wait France 1 1 = Check for tone Hungary 1 All other countries 0 PBX pre dial pause mode.
49 PSTN blind dial wait time. Delay from OFF hook to the start of dialing when blind dialing, no dial tone is detected, and the unit is configured for PSTN operation.
50 Obsolete PBX blind dial wait time. The delay from OFF hook to the start of dialing when blind dialing, no dial tone is detected, and the unit is configured for PBX operation.
51 52 Time of each pause. Duration of the delay when pause characters in a dial string are interpreted as delays. Number of user entered pauses allowed. Maximum number of pauses that a user can enter in a dial string.
53 PSTN dial tone evaluation time. Maximum total time that the LaserJet 3200 will wait for PSTN dial tone.
54 55 PSTN dial tone detect frequencies. Indicates the frequency combination that is used to identify a PSTN dial tone. PSTN dial tone detection time minimum. Indicates the total time a PSTN dial tone sequence must be present for a PSTN dial tone to be detected.
60 PSTN dial tone detect threshold. Sets the detection threshold for a PSTN dial tone. If below this level, the PSTN tone will not be detected. -0.1 dBm (260 to 510 which is -26.0 to 51.
61 62 63 PSTN dial tone frequency 1. The center frequency for the first component of the PSTN dial tone. PSTN dial tone frequency 2. Center frequency for the second component of the PSTN dial tone. PSTN dial tone frequency 3. Center frequency for the third component of the PSTN dial tone.
68 Obsolete 69 Obsolete Special dial tone detect. Indicates the frequency combination that is used to identify a special dial tone. Special dial tone detection time minimum. The total time a special dial tone sequence must be present for a special dial tone to be detected. 0 = no freq. 1=1 2=2 3=1 and 2 5=1 or 2 6=1 or 2 or 3 Ireland 1 U.K. 1 All other countries 0 1 ms (0 ms to 15000 ms) Ireland 1000 U.K. 1000 All other countries 0 70 Obsolete Special dial tone minimum on time.
77 Obsolete Special dial tone frequency 3. Center frequency for the third component of the special dial tone. 1 Hz (0 Hz to 700 Hz) Ireland 80 U.K. 80 All other countries 0 78 Obsolete SPCL dial tone frequency 1 bandwidth. Tone filter bandwidth used for special dial tone detection. 20 = 20 Hz 40 = 40 Hz All countries 0 79 Obsolete SPCL dial tone frequency 2 bandwidth. Tone filter bandwidth used for special dial tone detection.
82 Pre dial shunt. The duration that the dial shunt relay is activated prior to pulse dialing the first digit in a dial string. Not present on all LIUs.
83 Post dial shunt. The duration that the dial shunt relay remains active after the pulse dialing the last digit in a dial string. Not present on all LIUs.
84 Dial pulse break time. The duration that the dial pulse relay will be opened to cause a break of loop current during pulse dialing.
85 Dial pulse make time. The duration that the dial pulse relay will be closed to cause a make of loop current during pulse dialing.
86 Dial pulse inter-digit time. The duration between digits when pulse dialing, measured from the end of the last make to the start of the first break of the next digit.
87 DTMF duration and interdigit time. Duration of each DTMF signal and the duration of the interdigit silence.
88 Open flash time. Controls the duration of the open flash when the LaserJet 3200 is configured to produce this flash type.
89 Phone inactivity abort timer. Specifies the time from end of dialing until the unit disconnects if no response is detected from the answering machine. (Note: This parameter is active when the T30 inactivity abort timer, parameter 131, is active. Change parameter 131 also when this parameter is changed.
Call progress Parameter Description Units Country Default 90 Busy tone detect enable. If TRUE, busy tone detection is enabled at the completion of dialing. If FALSE, no busy tone will be detected and the call will either connect or fail due to no answer. 0 = False 1 = True All countries 1 91 Busy tone frequencies. Indicates the frequency combination that is used to identify the call progress tone.
92 Busy tone minimum on time. Minimum duration a call progress tone must be present for a cadenced sequence to be valid.
93 Busy tone maximum on time. Maximum duration a call progress tone can be present for a cadenced sequence to be valid.
94 Busy tone minimum off time. Minimum period of silence that must exist between cadenced call progress tones if the tone sequence is to be valid.
95 Busy tone maximum off time. Maximum period of silence that can exist between cadenced call progress tones if the tone sequence is to be valid.
96 Complex impedance enable. Enables complex impedance mode when off hook. 0 = False 1 = True Argentina 0 Australia 1 Austria 1 Belgium 1 Canada 0 China 0 Denmark 1 Finland 1 France 1 Germany 1 Greece 1 Hong Kong 0 Hungary 0 Ireland 1 Israel 0 Italy 1 Korea 0 Malaysia 0 Mexico 0 Netherlands 1 New Zealand 1 Norway 1 Poland 0 Portugal 1 Russia 0 Singapore 0 Spain 1 Sweden 1 Switzerland 1 Taiwan 0 Ukraine 0 U.K. 1 U.S.
97 Busy tone frequency 1. The center frequency for the first component of the call progress tone.
98 Busy tone frequency 2. The center frequency for the second component of the call progress tone.
99 100 101 102 103 Busy tone frequency 1 bandwidth. Tone filter bandwidth used for busy tone detection. Busy tone frequency 2 bandwidth. Tone filter bandwidth used for busy tone detection. 20 = 20 Hz 40 = 40 Hz 60 = 60 Hz 80 = 80 Hz 100 = 100 Hz 200 = 200 Hz Units: Same as parameter 99. Argentina 200 Canada 200 China 200 Israel 200 Korea 200 Mexico 200 U.S. 200 All other countries 100 Argentina 200 Canada 200 China 200 Israel 200 Korea 200 Mexico 200 U.S.
104 105 Pulse dial disable. Removes the dialing mode menu item from the fax send setup user menu, so the user cannot select pulse dial mode. The LaserJet 3200 does not meet pulse dialing regulatory requirements in Australia and New Zealand. 0 = False Australia 1 1 = True New Zealand 1 All other countries 0 Spare 105. N/A All countries 0 Modem configuration Parameter Description Units Country Default 106 Equalizer. Used to select the transmission compromise equalizer.
107 LIU receive loss. Specifies the LIU receive loss. The receive loss is introduced between the modem and the external telephone line interface jack. It is used to correctly adjust the internal modem receive level so that the receive level at the telephone line interface jack is as specified by MODEM MINIMUM CARRIER DETECTION LEVEL. -0.
108 LIU transmit loss. Specifies the LIU transmit loss. This transmission loss is introduced between the modem and the telephone line interface jack. It is used to correctly adjust the modem and DTMF transmit levels so that the level at the telephone line interface jack is as specified by the MODEM TRANSMIT LEVEL. -0.
109 DTMF transmit level high group. The DTMF transmit level for the high group of frequencies in the DTMF tone pair. -0.
110 DTMF transmit delta low group. The relative transmit level (“twist”) of the low group of frequencies in the DTMF tone pair. -0.1 dB (0 to 40) Russia Ukraine All other countries 111 Modem minimum carrier detection level. Specifies the minimum modem receive level that is presented from the PSTN at the external telephone interface jack. -0.1 dBm (350 to 510) Russia Ukraine All other countries 30 (-3.0 dB) 30 (-3.0 dB) 20 (-2.0 dB) 430 (43.0 dBm) 430 (43.0 dBm) 440 (44.
112 Tone transmit level. Specifies the CNG and CED tone level that is presented to the PSTN at the external telephone line interface jack. -0.
113 Data transmit level. Specifies the data transmit level that is presented to the PSTN at the external telephone line interface jack. The default value is 100 (0.1 dBm) for all countries. -0.1 dBm (0 to 255) Norway 110 Poland 80 All other countries 100 114 V17 14400 EQM threshold. The Eye Quality Monitor measures the received signal quality. When the EQM exceeds the threshold set here during training (TCF), the modem drops to a lower speed.
125 Echo protect mode. Enables transmission of an echo protect tone prior to the transmission of the training sequence. 0 = Echo protect all modulations except V.29 All countries 0 1 = Enable on all modulations 2 = Disable on all modulations 126 Percent of contiguous 0s during training (TCF) required. The value 0 disables this check. Percentage (0 to 95) All countries 80 127 No carrier timer. If carrier is lost for this duration during high speed receive, the session fails with result code 283.
130 Answer inactivity abort timer. Specifies the time from going OFF hook and waiting for an incoming fax handshake, until the LaserJet 3200 disconnects because no incoming fax activity is detected.
131 Originate inactivity abort timer. Specifies the time from starting t.30 until the LaserJet 3200 disconnects because no fax is detected. (Note: This timer is active when the phone inactivity timer, parameter 89, is active. Change parameter 89 also when this parameter is changed.
132 T5 timer. Determines the maximum time that a transmitting machine will wait for a receiving machine to stop sending RNR.
133 134 DTS Compliance Enable. German DTS compliance requires a slightly different T30 implementation. The differences are primarily concerned with handling voice interrupts. If the value = 1 (True), the T30 operation will comply with the DTS requirement. If 0 (False), the T30 operation will comply with the CCITT requirement. (This parameter may also be known as "BZT compliance", since BZT is the testing organization.) 0 = False 1 = True Manual dial abort timer.
140 141 Obsolete Number of call attempts timer 2. Specifies the number if repeat calls that are attempted using parameter 138 as the interval between call attempts. Blacklist enable. If TRUE, creates a list of numbers which have failed on all re-dial attempts.
147 User interface time format. 0 = AM/PM 1 = 24 hr Argentina 0 Australia 0 Austria 1 Belgium 1 Canada 0 China 0 Denmark 1 Finland 1 France 1 Germany 1 Greece 1 Hong Kong 0 Hungary 1 Ireland 1 Israel 1 Italy 1 Korea 0 Malaysia 0 Mexico 0 Netherlands 1 New Zealand 0 Norway 1 Poland 1 Portugal 1 Russia 1 Singapore 0 Spain 1 Sweden 1 Switzerland 1 Taiwan 0 Ukraine 1 U.K. 1 U.S.
148 User interface date format. 149 User interface language invalid – not sure how, or if, this is used in the LaserJet 3200. NOTE: 0 = mmddyy 1 = ddmmyy 2 = yymmdd N/A Canada 0 China 0 U.S. 0 All other countries 1 All countries 0 All parameters above 149 are not country specific. Transmission/reception settings/T30 Parameter Descriptions Units 150 Maximum DIS FIF size. Some older fax machines may not understand the longer DIS sent when the LaserJet 3200 answers.
153 Transmit data rate maximum. The default value is 26. 0 = V.17 14400 1 = V.17 12000 2 = V.17 9600 3 = V.17 7200 4 = V.33 14400 5 = V.33 12000 6 = V.29 9600 7 = V.29 7200 8 = V.29 4800 9 = V.27 4800 10 = V.27 2400 11 = V.21 300 12 = V.34 1200 13 = V.34 2400 14 = V.34 4800 15 = V.34 7200 16 = V.34 9600 17 = V.34 12000 18 = V.34 14400 19 = V.34 16800 20 = V.34 19200 21 = V.34 21600 22 = V.34 24000 23 = V.34 26400 24 = V.34 28800 25 = V.34 31200 26 = V.34 33600 154 Transmit ECM enable.
162 Receive minimum scan line time. This parameter defines how long the sender must take to send each line when the session is non-ECM. The default value is 0. (5/5 means 5 ms for std and 5 ms for fine. 20/10 means 20 ms for std and 10 ms for fine.) 0 1 2 3 4 5 6 7 = 0/0 ms = 5/5 ms = 10/10 ms = 20/20 ms = 40/40 ms = 10/5 ms = 20/10 ms = 40/20 ms 163 Ignore first DIS. If an international connection has a lot of echo, ignoring the first DIS may help the line stabilize. The default value is 0.
173 Ring volume. Speaker volume for the phone ring. Modified by the user from the volume settings menu. The default value is 1. 0 = Off 1 = Soft 2 = Medium 3 = Loud 174 Key press (beep) volume. Speaker volume for key press beeps. Modified by the user from the volume settings menu. The default value is 1. 0 = Off 1 = Soft 2 = Medium 3 = Loud 175 Monitor volume. Speaker volume when monitoring the phone line during dialing. Modified by the user via the front panel volume key. The default value is 96.
186 TTI (transmit terminal identification) control. If TRUE, the header information will be included on each fax page sent by the LaserJet 3200. The default value is 1. 0 = False 1 = True Image adjustments and miscellaneous Parameter Descriptions Units 187 Maximum auto reduction. Limits the amount of scaling on auto reduction. Scaling down too far results in unreadable faxes. This tends to occur when the sending fax jams or double feeds a document. The default value is 60.
199 Ciocb register (in codec) default value for Rare liu. This value is written to a modem control register and should not be changed without a detailed understanding of the consequences. 200 Ciocb register (in codec) eavesdrop value for Rare liu. This value is written to a modem control register and should not be changed without a detailed understanding of the consequences. 201 Fax receive disposition.
