hp LaserJet 4100 mfp prepare for setup you will need the following addresses to set up the product: 1) IP address (network) 2) SMTP gateway (e-mail server) 3) LDAP gateway (directory services) – optional start 1) IP 2) SMTP 3) LDAP
© Copyright Hewlett-Packard Company 2001 Warranty All Rights Reserved. The information contained in this document is subject to change without notice. Except as allowed by copyright laws or herein, reproduction, adaptation, or translation without prior written permission is prohibited.
2 1 1040 mm (41 inches) HP LaserJet 4100 mfp 415 mm (16.4 inches) HP LaserJet 4100 mfp 540 mm (21.25 inches) Regulate the environment. Do not place in direct sunlight or near chemicals. Make sure that the environment is free from abrupt temperature or humidity changes. • Temperature: 50° to 91° F (10° to 32.5° C) • Relative humidity: 20% to 80% !" #$%& '( )*+,-./ 012 345 6 )7 89:;< )*=>>?@>ABCDCAA?@AE?C F G)7 H?IJ?CKLM" N OPQRSD9TUVW X3 #$Y Z [\D]\^_`ab
2 5 1 6 3 10 1 9 2 8 7 11 4 4 10 3 5 9 6 5 6 8 English 7 Identify parts (front view). 1) Automatic document feeder (ADF) cover 2) ADF 3) Flatbed cover 4) Top cover (access to serial and model numbers) 5) Power switch 6) Tray 2 7) Tray 1 8) Toner cartridge access (under top cover) 9) Control panel 10) Front output bin Identify parts (back view).
9 1 3 2 4 3 3) Pull the sealing tab tape from the end of the toner cartridge to remove the entire length of tape. Avoid touching any black toner on the tape. 4) Slide the cartridge into the product as far as it can go. Install accessories. Use the separate installation instructions to install any accessories that you have purchased with the product.
11 1 4 2 English 5 4) Squeeze the blue tab on the right side of the tray and move it to the correct position based on the media size. 5) Slide the tray back into the product. (Repeat these steps for optional trays.) Connect the power cord. 1) Locate the power switch on the right side of the product. Make sure that the power is turned off. 2) Connect the jumper cord to the product, and then connect the power cord to the jumper cord.
13 14 Turn the product on. Turn the power on and wait for the product to warm up. After the product warms up, the product prompts you to set the control panel language. Set the control panel language. Choose the language from the available options. After the language is set, READY reappears on the display. DEFGH >? ÂN)* aÊOP QÈ" QÈéÊ R _ò5íS TU" I JKLMNO ¡µ -Vâ-WTU" S TUéÊ 5 _.XxYCÚF»¼Z-[\M" 16 15 1 2 Set the IP Address. To configure the mfp, first set the IP/network address.
17 18 1 English 2 Set the e-mail gateway addresses manually. 1) Select SMTP GATEWAY, in the I/O menu and enter the gateway address. 2) Select LDAP GATEWAY, in the I/O menu and enter the gateway address. (Note: The SMTP gateway address is required, but the LDAP gateway address is optional.) Select TEST SEND GATEWAYS to check the addresses have been configured correctly. Test the digital sending function.
copyright © 2001 Hewlett-Packard Company http://www.hp.
