Cisco Gigabit Ethernet Switch Module for HP p-Class BladeSystem Software Configuration Guide

27-50
Cisco Gigabit Ethernet Switch Module for HP p-Class BladeSystem Software Configuration Guide
380261-003
Chapter 27 Configuring QoS
Configuring Standard QoS
Switch(config-pmap-c)# police 1000000 8000 exceed-action policed-dscp-transmit
Switch(config-pmap-c)# exit
Switch(config-pmap)# exit
Switch(config)# interface gigabitethernet0/1
Switch(config-if)# service-policy input flow1t
This example shows how to create a Layer 2 MAC ACL with two permit statements and attach it to an
ingress port. The first permit statement allows traffic from the host with MAC address 0001.0000.0001
destined for the host with MAC address 0002.0000.0001. The second permit statement allows only
Ethertype XNS-IDP traffic from the host with MAC address 0001.0000.0002 destined for the host with
MAC address 0002.0000.0002.
Switch(config)# mac access-list extended maclist1
Switch(config-ext-mac)# permit 0001.0000.0001 0.0.0 0002.0000.0001 0.0.0
Switch(config-ext-mac)# permit 0001.0000.0002 0.0.0 0002.0000.0002 0.0.0 xns-idp
Switch(config-ext-mac)# exit
Switch(config)# mac access-list extended maclist2
Switch(config-ext-mac)# permit 0001.0000.0003 0.0.0 0002.0000.0003 0.0.0
Switch(config-ext-mac)# permit 0001.0000.0004 0.0.0 0002.0000.0004 0.0.0 aarp
Switch(config-ext-mac)# exit
Switch(config)# class-map macclass1
Switch(config-cmap)# match access-group maclist1
Switch(config-cmap)# exit
Switch(config)# policy-map macpolicy1
Switch(config-pmap)# class macclass1
Switch(config-pmap-c)# set dscp 63
Switch(config-pmap-c)# exit
Switch(config-pmap)# class macclass2 maclist2
Switch(config-pmap-c)# set dscp 45
Switch(config-pmap-c)# exit
Switch(config-pmap)# exit
Switch(config)# interface gigabitethernet0/1
Switch(config-if)# mls qos trust cos
Switch(config-if)# service-policy input macpolicy1
Classifying, Policing, and Marking Traffic on SVIs by Using Hierarchical Policy Maps
You can configure hierarchical policy maps on SVIs, but not on other types of interfaces. Hierarchical
policing combines the VLAN- and interface-level policy maps to create a single policy map.
On an SVI, the VLAN-level policy map specifies which traffic class to act on. Actions can include
trusting the CoS, DSCP, or IP precedence values or setting a specific DSCP or IP precedence value in
the traffic class. Use the interface-level policy map to specify the physical ports that are affected by
individual policers.
Follow these guidelines when configuring hierarchical policy maps:
• Before configuring a hierarchical policy map, you must enable VLAN-based QoS on the physical
ports that are to be specified at the interface level of the policy map.
• You can attach only one policy map per ingress port or SVI.
• A policy map can contain multiple class statements, each with different match criteria and actions.
• A separate policy-map class can exist for each type of traffic received on the SVI.
• A policy-map trust state and a port trust state are mutually exclusive, and whichever is configured
last takes affect.
• If you configure the IP-precedence-to-DSCP map by using the mls qos map ip-prec-dscp
dscp1...dscp8 global configuration command, the settings only affect packets on ingress interfaces
that are configured to trust the IP precedence value. In a policy map, if you set the packet IP