Release Notes for Cisco Catalyst Blade Switch 3120 for HP, Cisco IOS Release 12.2(53)SE and Later
Table Of Contents
- Release Notes for Cisco Catalyst Blade Switch 3120 for HP, Cisco IOS Release 12.2(53)SE and Later
- Contents
- System Requirements
- Upgrading the Switch Software
- Installation Notes
- New Features
- Minimum Cisco IOS Release for Major Features
- Limitations and Restrictions
- Important Notes
- Open Caveats
- Resolved Caveats
- Documentation Updates
- Updates to the Software Documentation
- Update to the “Configuring IP Unicast Routing” Chapter
- User Interface for VRF-Aware RADIUS
- Update to the “Configuring IEEE 802.1x Port-Based Authentication” Chapter
- Update to the “Configuring IEEE 802.1x Port-Based Authentication” Chapter
- Update to the “Configuring Embedded Event Manager” Chapter
- Update to the “Configuring MSTP” Chapter
- Updates to the Switch Getting Started Guide
- Updates for the System Message Guide
- Updates to the Software Documentation
- Related Documentation
- Obtaining Documentation and Submitting a Service Request
![](/manual/hp/cisco-catalyst-1-10gbe-3120x-blade-switch/release-notes-for-cisco-catalyst-blade-switch-3120-for-hp-cisco-ios-release-12253se-and-later/images/img-27.png)
27
Release Notes for Cisco Catalyst Blade Switch 3120 for HP, Cisco IOS Release 12.2(53)SE and Later
OL-21144-02
Documentation Updates
Error Message %DOT1X-5-RESULT_OVERRIDE: Authentication result overridden for client
([chars]) on Interface [chars] AuditSessionID [chars]
Recommended Action
The authentication result was overridden. The first [chars] is the client ID, the
second [chars] is the interface, and the third [chars] is the session ID.
Explanation No action is required.
Error Message DOT1X-5-SUCCESS: Authentication successful for client ([chars]) on
Interface [chars] AuditSessionID [chars]
Explanation
Authentication was successful. The first [chars] is the client ID, the second [chars] is
the interface, and the third [chars] is the session ID.
Recommended Action No action is required.
Error Message DOT1X_SWITCH-5-ERR_ADDING_ADDRESS: Unable to add address [enet] on
[chars] AuditSessionID [chars]
Explanation
The client MAC address could not be added to the MAC address table because the
hardware memory is full or the address is a secure address on another port. This message might
appear if IEEE 802.1x is enabled. [enet] is the client MAC address, the first [chars] is the interface,
and the second [chars] is the session ID.
Recommended Action If the hardware memory is full, remove some of the dynamic MAC addresses.
If the client address is on another port, remove it from that port.
Error Message DOT1X_SWITCH-5-ERR_INVALID_PRIMARY_VLAN: Attempt to assign primary
VLAN [dec] to 802.1x port [chars] AuditSessionID [chars]
Explanation
An attempt was made to assign a primary VLAN to an IEEE 802.1x port, which is not
allowed. [dec] is the VLAN, the first [chars] is the port, and the second [chars] is the session ID.
Recommended Action Use a different VLAN.
Error Message DOT1X_SWITCH-5-ERR_INVALID_SEC_VLAN: Attempt to assign invalid
secondary VLAN [dec] to PVLAN host 802.1x port [chars] AuditSessionID [chars]
Explanation
An attempt was made to assign a nonsecondary VLAN to a private VLAN host
IEEE 802.1x port. [dec] is the VLAN, the first [chars] is the port, and the second [chars] is the
session ID.
Recommended Action Change the mode of the port so that it is no longer a PVLAN host port or use
a valid secondary VLAN.