Release Notes for Cisco Catalyst Blade Switch 3120 for HP, Cisco IOS Release 12.2(53)SE and Later
Table Of Contents
- Release Notes for Cisco Catalyst Blade Switch 3120 for HP, Cisco IOS Release 12.2(53)SE and Later
- Contents
- System Requirements
- Upgrading the Switch Software
- Installation Notes
- New Features
- Minimum Cisco IOS Release for Major Features
- Limitations and Restrictions
- Important Notes
- Open Caveats
- Resolved Caveats
- Documentation Updates
- Updates to the Software Documentation
- Update to the “Configuring IP Unicast Routing” Chapter
- User Interface for VRF-Aware RADIUS
- Update to the “Configuring IEEE 802.1x Port-Based Authentication” Chapter
- Update to the “Configuring IEEE 802.1x Port-Based Authentication” Chapter
- Update to the “Configuring Embedded Event Manager” Chapter
- Update to the “Configuring MSTP” Chapter
- Updates to the Switch Getting Started Guide
- Updates for the System Message Guide
- Updates to the Software Documentation
- Related Documentation
- Obtaining Documentation and Submitting a Service Request
![](/manual/hp/cisco-catalyst-1-10gbe-3120x-blade-switch/release-notes-for-cisco-catalyst-blade-switch-3120-for-hp-cisco-ios-release-12253se-and-later/images/img-32.png)
32
Release Notes for Cisco Catalyst Blade Switch 3120 for HP, Cisco IOS Release 12.2(53)SE and Later
OL-21144-02
Documentation Updates
Error Message DOT1X_SWITCH-5-ERR_VLAN_NOT_FOUND: Attempt to assign non-existent or
shutdown VLAN [dec] to 802.1x port [chars]
Explanation
An attempt was made to assign a VLAN to an IEEE 802.1x port, but the VLAN was not
found in the VLAN Trunking Protocol (VTP) database. [dec] is the VLAN, and [chars] is the port.
Recommended Action Make sure that the VLAN exists and is not shut down, or use another VLAN.
Error Message DOT1X_SWITCH-5-ERR_VLAN_ON_ROUTED_PORT: Dot1x cannot assign a VLAN
[dec] to a routed port [chars]
Explanation
An attempt was made to assign a VLAN to a supplicant on a routed port, which is not
allowed. [dec] is the VLAN ID and [chars] is the port.
Recommended Action Either disable the VLAN assignment, or change the port type to a nonrouted
port.
Error Message DOT1X_SWITCH-5-ERR_VLAN_PROMISC_PORT: Attempt to assign VLAN [dec] to
promiscuous 802.1x port [chars]
Explanation
An attempt was made to assign a VLAN to a promiscuous IEEE 802.1x port, which is
not allowed. [dec] is the VLAN, and [chars] is the port.
Recommended Action Change the port mode so that it is no longer a promiscuous port, or change the
configuration so that no VLAN is assigned.
Error Message DOT1X_SWITCH-5-ERR_VLAN_RESERVED: Attempt to assign reserved VLAN
[dec] to 802.1x port [chars]
Explanation
An attempt was made to assign an invalid VLAN to an IEEE 802.1x port. The VLAN
specified is a reserved VLAN and cannot be assigned to this port. [dec] is the VLAN, and [chars] is
the port.
Recommended Action Assign a different VLAN.
Error Message DOT1X_SWITCH-5-ERR_VLAN_RSPAN: Attempt to assign RSPAN VLAN [dec] to
802.1x port [chars]. 802.1x is incompatible with RSPAN
Explanation
This message means that remote SPAN should not be enabled on a VLAN with
IEEE 802.1x-enabled. [dec] is the VLAN, and [chars] is the port.
Recommended Action Either disable remote SPAN configuration on the VLAN, or disable
IEEE 802.1x on all the ports in this VLAN.