Cisco MDS 9200 Series Hardware Installation Guide April 2008 Americas Headquarters Cisco Systems, Inc. 170 West Tasman Drive San Jose, CA 95134-1706 USA http://www.cisco.
THE SPECIFICATIONS AND INFORMATION REGARDING THE PRODUCTS IN THIS MANUAL ARE SUBJECT TO CHANGE WITHOUT NOTICE. ALL STATEMENTS, INFORMATION, AND RECOMMENDATIONS IN THIS MANUAL ARE BELIEVED TO BE ACCURATE BUT ARE PRESENTED WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED. USERS MUST TAKE FULL RESPONSIBILITY FOR THEIR APPLICATION OF ANY PRODUCTS.
Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o .
Contents 18/4-Port Multiservice Module 1-19 18/4-Port Multiservice Federal Information Processing Standards Module LEDs on the 18/4-Port Multiservice Module 1-20 14/2-Port Multiprotocol Services Module 1-21 LEDs on the 14/2-Port Multiprotocol Services Module 1-22 IP Storage Services Modules 1-23 LEDs on IP Storage Services Module 1-24 32-Port Fibre Channel Storage Services Module 1-25 LEDs on the Storage Services Module 1-26 32-Port Fibre Channel Advanced Services Module 1-27 LEDs on the Fibre Channel Adva
Contents Grounding the Chassis 2-24 Starting Up the Switch 2-26 Removing and Installing Components 2-28 Removing and Installing Switching and Services Modules 2-28 Removing a Caching Services Module 2-31 Removing Other Switching or Services Modules 2-32 Installing a Switching or Services Module, Including Caching Services Modules Verifying Installation of a Switching or Services Module 2-34 Maintaining a Caching Services Module 2-35 Maintaining the Batteries on the Caching Services Module 2-35 Maintain
Contents Requirements Specific to Perforated Cabinets A-2 Requirements Specific to Solid-Walled Cabinets A-3 Requirements Specific to Standard Open Racks A-3 Requirements Specific to telco Racks A-3 Cisco MDS 9000 Family telco and EIA Shelf Bracket A-4 Rack-Mounting Guidelines A-4 Before Installing the Shelf Brackets A-5 Required Equipment A-5 Installing the Shelf Bracket Kit into a Two-Post telco Rack A-6 Installing the Shelf Bracket Kit into a Four-Post EIA Rack A-7 Installing the Switch on the Shelf Bra
Contents Environmental and Power Requirement Specifications for Cisco Fibre Channel/Gigabit Ethernet SFP Transceivers B-14 Cisco CWDM SFP Transceivers B-15 Environmental and Optical Specifications for Cisco 2-Gbps CWDM SFP Transceivers B-16 Environmental and Optical Specifications for Cisco 4-Gbps CWDM SFP Transceivers B-18 Cisco CWDM OADMs B-19 Cisco CWDM OADM Comparison B-19 Environmental and Power Requirement Specifications for Cisco CWDM OADMs B-20 Cisco Gigabit Ethernet Transceivers B-20 General Speci
Contents Cisco MDS 9200 Series Hardware Installation Guide viii OL-16188-01
Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m New and Changed Information The Cisco MDS 9200 Series Hardware Installation Guide applies to Cisco MDS SAN-OS Release 3.3 (1a) or later. Table 1 lists the new and changed features available with each supported Cisco MDS SAN-OS release for the Cisco MDS 9200 Series, with the latest release first.
New and Changed Information Table 1 Documented Features for the Cisco MDS 9200 Series (continued) Feature Description Cisco MDS 9222i Mutiservice Modular Switch Added the new 18/4 Fibre Channel port and 4 Gigabit Ethernet IP services port Multiservice Modular Switch. Changed in Release 3.
New and Changed Information Table 1 Documented Features for the Cisco MDS 9200 Series (continued) Changed in Release Feature Description 12-port 4-Gbps Fibre Channel switching module 3.0(1) Added 12-port 4-Gbps Fibre Channel switching module. The switching module can be used in any of the Cisco MDS 9500 Series chassis and in the Cisco MDS 9216i and 9216A Switches. The “12-port 4-Gbps Fibre Channel Switching Module” section on page 1-14 and the “Technical Specifications” section on page B-1.
New and Changed Information Cisco MDS 9200 Series Hardware Installation Guide xii OL-16188-01
Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Preface This preface describes the audience, organization, and conventions of the Cisco MDS 9200 Series Hardware Installation Guide. It also provides information on how to obtain related documentation. Audience To use this installation guide, you must be familiar with electronic circuitry and wiring practices and preferably be an electronic or electromechanical technician.
Preface Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Conventions This document uses the following conventions for notes, cautions, and safety warnings. Notes and Cautions contain important information that you should be aware of. Note Means reader take note. Notes contain helpful suggestions or references to material that are not covered in the publication. Caution Means reader be careful.
Preface Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Warnung Dieses Warnsymbol bedeutet Gefahr. Sie befinden sich in einer Situation, die zu einer Körperverletzung führen könnte. Bevor Sie mit der Arbeit an irgendeinem Gerät beginnen, seien Sie sich der mit elektrischen Stromkreisen verbundenen Gefahren und der Standardpraktiken zur Vermeidung von Unfällen bewußt.
Preface Related Documentation Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Related Documentation The documentation set for the Cisco MDS 9000 Family includes the following documents. The documentation set for the Cisco MDS 9000 Family includes the following documents. To find a document online, use the Cisco MDS SAN-OS Documentation Locator at: http://www.cisco.com/en/US/products/ps5989/products_documentation_roadmap09186a00804500c1.html .
Preface Related Documentation Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o .
Preface Obtaining Documentation, Obtaining Support, and Security Guidelines Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Obtaining Documentation, Obtaining Support, and Security Guidelines For information on obtaining documentation, submitting a service request, and gathering additional information, see the monthly What’s New in Cisco Product Documentation, which also lists all new and revised Cisco technical documentation, at: http://www.cisco.
Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m CH A P T E R 1 Product Overview The Cisco MDS 9200 Series of multilayer modular fabric switches supports storage area network (SAN) applications. The Cisco MDS 9200 Series switches provide scalability, multitransport capability, security, and manageability to enterprise SANs.
Chapter 1 Product Overview Chassis Note The Cisco MDS 9200 Series requires Cisco MDS SAN-OS Release 2.0(x) or later. The Cisco MDS 9222i Switch requires MDS SAN-OS Release 3.
Chapter 1 Product Overview Chassis The Cisco MDS 9216A (see Figure 1-3) has a nonremovable supervisor module (in slot 1) with an integrated 16-port Fibre Channel switching module. See the “Cisco MDS 9216A Integrated Supervisor Module” section on page 1-7.
Chapter 1 Product Overview Chassis Figure 1-2 Cisco MDS 9216i Chassis 3 MD 1 S 92 2 3 2 116888 1 16 i 4 5 6 7 8 9 10 11 12 13 14 LIN K GE 4 1 LIN K GE 2 1 Fan module 3 Supervisor module with integrated 14-port Fibre Channel and 2-port Gigabit Ethernet switching module 2 Switching module or Services module (such as the IPS module) 4 Interface module Figure 1-3 Cisco MDS 9216A Chassis 1 4 3 240805 2 1 Fan module 3 Supervisor module with integrated 16-port Fibre Chann
Chapter 1 Product Overview Cisco MDS Fibre Channel Bladeswitch for IBM Blade Center The Cisco MDS 9200 Series supports the following additional modules: • The nonremovable interface module (located above the integrated supervisor module), provides the console port (COM1 port) and the MGMT 10/100 Ethernet port for the integrated supervisor module. See the “Interface Modules” section on page 1-10. • An optional module in the open slot (slot 2).
Chapter 1 Product Overview Integrated Supervisor Modules Cisco MDS 9222i Integrated Supervisor Module The nonremovable Cisco MDS 9222i integrated supervisor module provides the control and management functions of the Cisco MDS 9222i Switch, and it includes an integrated 18-port Fibre Channel switching and 4-port Gigabit Ethernet IP services module. The Cisco MDS 9222i integrated supervisor module provides multiple communication and control paths to avoid a single point of failure.
Chapter 1 Product Overview Integrated Supervisor Modules Figure 1-5 shows the Cisco MDS 9216i integrated supervisor module with an integrated 14-port Fibre Channel and 2-port Gigabit Ethernet module.
Chapter 1 Product Overview Integrated Supervisor Modules Figure 1-6 shows the Cisco MDS 9216A supervisor module with an integrated 16-port Switching module.
Chapter 1 Product Overview Integrated Supervisor Modules LEDs on the Cisco MDS 9200 Series Integrated Supervisor Modules Table 1-1 describes the LEDs for the Cisco MDS 9200 Series integrated supervisor modules. Table 1-1 LEDs for the Cisco MDS 9200 Series Integrated Supervisor Modules LED Status Description Status Green All diagnostics pass. The module is operational (normal initialization sequence).
Chapter 1 Product Overview Interface Modules Interface Modules The nonremovable interface module is located above slot 1 (see Figure 1-7) and is identical for all Cisco MDS 9200 Series switches. It provides the following local and remote management interfaces: • RS-232 (EIA/TIA-232) console port with an RJ-45 connection that you can use to: – Configure the switch from the CLI. – Monitor network statistics and errors. – Configure SNMP agent parameters.
Chapter 1 Product Overview Interface Modules LEDs on the Interface Module Table 1-2 describes the LEDs for the Cisco MDS 9200 Series interface module. Table 1-2 LEDs on the Cisco MDS 9200 Series Interface Module LED Status Description Status Green All diagnostics pass. The module is operational (normal initialization sequence). Orange One of the following occurs or occurred: Red System Green • The module is booting or running diagnostics (normal initialization sequence).
Chapter 1 Product Overview Cisco MDS 9000 Family Module Compatibility Cisco MDS 9000 Family Module Compatibility Table 1-3 lists the hardware modules available and the chassis compatibility associated with them.
Chapter 1 Product Overview Switching Modules The Fibre Channel switching modules provide system-wide power management and autonegotiation, which allows ports to negotiate for speed at the other end of the link. Each module has temperature sensors and an EEPROM that stores serial number and model number information. The Fibre Channel port interfaces support hot-swappable Fibre Channel SFP transceivers that can be short wavelength (SWL) or long wavelength (LWL).
Chapter 1 Product Overview Switching Modules 24-port 4-Gbps Fibre Channel Switching Module The 24-port 4-Gbps Fibre Channel switching module offers 24 autosensing 1-, 2-, and 4-Gbps Fibre Channel ports and can be used in any of the Cisco MDS 9500 Series chassis and in the Cisco MDS 9216i and 9216A Switches. The 24-port switching module can be configured in one of two operational modes: shared bandwidth mode (default) and dedicated bandwidth mode.
Chapter 1 Product Overview Switching Modules 4-port 10-Gbps Fibre Channel Switching Module The 4-port 10-Gbps Fibre Channel switching module offers four dedicated bandwidth Fibre Channel ports running at 10 Gbps with no oversubscription. This module can be used in any of the Cisco MDS 9500 Series chassis and in the Cisco MDS 9216i and 9216A Switches.
Chapter 1 Product Overview Switching Modules LEDs on the Generation 2 Switching Modules Table 1-4 describes the LEDs for the 48-port, 24-port, and 12-port 4-Gbps Fibre Channel Switching Modules and the 4-port 10-Gbps Fibre Channel Switching Module. Table 1-4 LED LEDs for the Cisco MDS 9000 Family Generation 2 Fibre Channel Switching Modules Status Status Green Orange Red Link Solid green Description All diagnostics pass. The module is operational (normal initialization sequence).
Chapter 1 Product Overview Switching Modules Tip For a full 2-Gbps bandwidth between two hosts, connect one host to the first port group and the second host to the second port group.
Chapter 1 Product Overview Switching Modules Switching Module Features Each switching module draws its power from the 42 V supplied on the backplane with local DC/DC power converters and regulators. The control processor on the switching module provides power-on, offline, and online diagnostics. The control processor can be used to configure devices on the switching module and to gather statistical data from each port.
Chapter 1 Product Overview Switching Modules LEDs on the Generation 1 Switching Module Table 1-5 describes the LEDs for the 16-port and 32-port switching modules. Table 1-5 LED LEDs for the Cisco MDS 9000 Family Generation 1 Fibre Channel Switching Modules Status Status Green Orange Red Description All diagnostics pass. The module is operational (normal initialization sequence). One of the following occurs or occurred: • The module is booting or running diagnostics (normal initialization sequence).
Chapter 1 Product Overview Services Modules Services Modules The Cisco MDS 9200 Series supports the following hot-swappable services modules: • 1 8/4-Port Multiservice Module • 18/4-Port Multiservice Federal Information Processing Standards Module • 14/2-Port Multiprotocol Services Module • IP Storage Services Modules • 32-Port Fibre Channel Storage Services Module • 32-Port Fibre Channel Advanced Services Module • Caching Services Module The Cisco MDS 9200 Series supports one hot-swappable
Chapter 1 Product Overview Services Modules 18/4-Port Multiservice Federal Information Processing Standards Module The Cisco MDS 9000 Family 18/4-port Multiservice Federal Information Processing Standards (MSFM-18/4) module is a FIPS 140-2 Level 3-compliant version of the MSM-18/4 module.
Chapter 1 Product Overview Services Modules LEDs on the 18/4-Port Multiservice Module Table 1-6 describes the LEDs for the Cisco MDS 9000 Family 18/4-port Multiservice module. Table 1-6 LED LEDs for the Cisco MDS 9000 Family 18/4-Port Multiservice Modules Status Status Green Orange Red Link Description All diagnostics pass. The module is operational (normal initialization sequence).
Chapter 1 Product Overview Services Modules The MPS-14/2 modules support FCIP compression to maximize the effective WAN bandwidth of SAN extension solutions. It achieves up to a 30-to-1 compression ratio, with typical ratios of 2-to-1 over a wide variety of data sources. With the addition of hardware-based compression, the MPS-14/2 module is able to provide optimal levels of compressed throughput for implementations across low to high-bandwidth links.
Chapter 1 Product Overview Services Modules LEDs on the 14/2-Port Multiprotocol Services Module Table 1-7 describes the LEDs for the MPS-14/2 modules. Table 1-7 LED LEDs for the Cisco MDS 9000 Family MPS-14/2 Modules Status Status Green Orange Red Description All diagnostics pass. The module is operational (normal initialization sequence). One of the following occurs or occurred: • The module is booting or running diagnostics (normal initialization sequence).
Chapter 1 Product Overview Services Modules The Fibre Channel port interfaces support hot-swappable Fibre Channel SFP transceivers, which can be short wavelength (SWL) for connectivity up to 1640 feet (500 meters), or long wavelength (LWL) for connectivity up to 6.2 miles (10 km). The port interfaces also support coarse wavelength-division multiplexing (CWDM) SFP transceivers, which can be used for extended long wavelength (ELWL) transmission or for CWDM.
Chapter 1 Product Overview Services Modules LEDs on IP Storage Services Module Table 1-8 describes the LEDs for the IPS module. Table 1-8 LEDs for the Cisco MDS 9000 Family IPS Modules LED Status Description Status Green All diagnostics pass. The module is operational (normal initialization sequence). Orange One of the following occurs or occurred: Red • The module is booting or running diagnostics (normal initialization sequence).
Chapter 1 Product Overview Services Modules The Fibre Channel ports support hot-swappable Fibre Channel SFP transceivers, which can be short wavelength (SWL) for connectivity up to 1050 feet (500 m), or long wavelength (LWL) for connectivity up to 6.2 miles (10 km). All interfaces are autosensing 1-Gbps or 2-Gbps compatible. The ports also support coarse wavelength-division multiplexing (CWDM) SFP transceivers, which can be used for extended long wavelength (EWL) transmission or for CWDM.
Chapter 1 Product Overview Services Modules LEDs on the Storage Services Module Table 1-9 describes the LEDs for the Cisco MDS 9000 Family Storage Services Module. Table 1-9 LEDs for the Cisco MDS 9000 Family Storage Services Module LED Status Description Status Green All diagnostics pass. The module is operational (normal initialization sequence). Orange One of the following occurs or occurred: Red Speed Link • The module is booting or running diagnostics (normal initialization sequence).
Chapter 1 Product Overview Services Modules The Fibre Channel port interfaces support hot-swappable Fibre Channel SFP transceivers, which can be SWL for connectivity up to 1640 feet (500 meters), or LWL for connectivity up to 6.2 miles (10 km). All interfaces are autosensing 1-Gbps or 2-Gbps compatible. The port interfaces also support CWDM SFP transceivers, which can be used for extended long wavelength (ELWL) transmission or for CWDM. See the “Supported Transceivers” section on page 1-35.
Chapter 1 Product Overview Services Modules LEDs on the Fibre Channel Advanced Services Module Table 1-10 describes the LEDs for the Cisco MDS 9000 Family ASM. Table 1-10 LEDs for the Cisco MDS 9000 Family ASM LED Status Description Status Green All diagnostics pass and the module is operational (normal initialization sequence). Orange One of the following occurs or occurred: Red Speed Link • The module is booting or running diagnostics (normal initialization sequence).
Chapter 1 Product Overview Services Modules The CSM shuts down if the software failure or an external power failure occurs, or if the module is separated from the backplane while it is still powered on. The CSM automatically backs up the data in memory to the disk drives and then shuts down. The CSM batteries provide adequate power to back up data without external power. Figure 1-21 shows the Cisco MDS 9000 Family CSM.
Chapter 1 Product Overview Services Modules Figure 1-22 Cisco MDS 9000 Family CSM (Internal View) 4 2 3 94038 1 1 Disk drive 2 3 Battery 2 2 Disk drive 1 4 Battery 1 See the “Removing and Installing Switching and Services Modules” section on page 2-28 for information about removing and installing the CSM and maintaining the CSM batteries.
Chapter 1 Product Overview Services Modules LEDs on the Caching Services Module Table 1-11 describes the LEDs for the CSM. Table 1-11 LEDs for the Cisco MDS 9000 Family CSM LED Status Description Status Green All diagnostics pass, and the module is operational (normal initialization sequence). Orange One of the following occurs or occurred: Red Node • The module is booting or running diagnostics (normal initialization sequence).
Chapter 1 Product Overview Power Supplies Power Supplies The Cisco MDS 9200 Series supports dual hot-swappable 845-W AC power supplies, each of which can supply sufficient power to the entire chassis should one power supply fail. The power supplies monitor their output voltage and provide status to the supervisor module. To prevent the unexpected shutdown of an optional module, power management software only allows a module to power up if adequate power is available.
Chapter 1 Product Overview Fan Module Fan Module The Cisco MDS 9200 Series supports a hot-swappable fan module with four fans. The fan module provides 80 cfm (cubic feet per minute) of cooling per slot, allowing 400 W of power dissipation per slot. Sensors on the supervisor module monitor the internal air temperature. If the air temperature exceeds a preset lower-level threshold, the environmental monitor displays warning messages.
Chapter 1 Product Overview Supported Transceivers For more information about the X2 transceiver, see the “X2 Transceiver Specifications” section on page B-6. For more information about a specific Cisco SFP transceiver, see the “SFP Transceiver Specifications” section on page B-9. SFP transceivers can be ordered separately or with the Cisco MDS 9200 Series. Note Use only Cisco transceivers in the Cisco MDS 9200 Series.
Chapter 1 Product Overview Supported Transceivers CWDM Combination Fibre Channel/Gigabit Ethernet SFP Transceivers All Fibre Channel and Gigabit Ethernet ports in the Cisco MDS 9200 Series support 1-Gbps/2-Gbps CWDM SFP transceivers. In addition, the Fibre Channel ports on Cisco MDS 9222i also support 4-Gbps CWDM SFP transceivers. The Cisco CWDM SFP transceivers have LC connectors and support both Gigabit Ethernet and Fibre Channel (1-Gbps/2-Gbps).
Chapter 1 Product Overview Supported Transceivers Cisco MDS 9200 Series Hardware Installation Guide 1-38 OL-16188-01
Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o .
Chapter 2 Installing the Cisco MDS 9200 Series Preinstallation Warning A readily accessible two-poled disconnect device must be incorporated in the fixed wiring. Statement 1022 Note Each new switch requires a license. For information on licensing, see the Cisco MDS 9000 Family CLI Configuration Guide or the Cisco MDS 9000 Family Fabric Manager Configuration Guide.
Chapter 2 Installing the Cisco MDS 9200 Series Preinstallation Installation Guidelines Follow these guidelines when installing the Cisco MDS 9200 Series: • Plan your site configuration and prepare the site before installing the chassis. Appendix D, “Site Planning and Maintenance Records,” lists the recommended site planning tasks. • Record the information listed in Appendix D, “Site Planning and Maintenance Records,” as you install and configure the switch.
Chapter 2 Installing the Cisco MDS 9200 Series Preinstallation Required Equipment Before beginning the installation, ensure that the following items are ready: • Number 1 and number 2 Phillips screwdrivers with torque capability • 3/16-in.
Chapter 2 Installing the Cisco MDS 9200 Series Installing the Chassis in a Cabinet or Rack Step 2 • Cables and connectors • Any optional items ordered Check for damage and report any discrepancies or damage to your customer service representative.
Chapter 2 Installing the Cisco MDS 9200 Series Installing the Chassis in a Cabinet or Rack Table 2-1 Contents of Cisco MDS 9200 Series Rack-Mount Kit (continued) Quantity Part Description 2 C brackets 6 12-24 x 3/4-inch Phillips binder-head screws 6 10-32 x 3/4-inch Phillips binder-head screws 4 M4 x 6-mm, Phillips countersunk screws To install the switch in a cabinet or rack using the rack-mount kit provided with the switch, follow these steps: Step 1 Install the front rack-mount brackets a
Chapter 2 Installing the Cisco MDS 9200 Series Installing the Chassis in a Cabinet or Rack Step 2 Install the C brackets on the switch as follows: Position one of the C brackets against the side of the switch and align the screw holes as shown in Figure 2-2 and Figure 2-3. Then attach the bracket to the switch with two of the flat-head M4 screws. a.
Chapter 2 Installing the Cisco MDS 9200 Series Installing the Chassis in a Cabinet or Rack C Brackets for the Cisco MDS 9200 Series (Close-Up View) 94297 Figure 2-3 Cisco MDS 9200 Series Hardware Installation Guide 2-8 OL-16188-01
Chapter 2 Installing the Cisco MDS 9200 Series Installing the Chassis in a Cabinet or Rack Step 3 Position the chassis in the rack, inserting the rear of the chassis between the front mounting rails (see Figure 2-4). Use the 12-24 x 3/4-in. or 10-32 x 3/4-in. screws (depending on the type of rack) to attach the front rack-mount brackets to the mounting rails (three per side).
Chapter 2 Installing the Cisco MDS 9200 Series Installing the Chassis in a Cabinet or Rack Inserting and Installing Slider Rails (Back View) 3 99001 Figure 2-5 2 1 1 Screws, 12-24 or 10-32 2 Slider rail 3 C bracket Cisco MDS 9200 Series Hardware Installation Guide 2-10 OL-16188-01
Chapter 2 Installing the Cisco MDS 9200 Series Installing the Switch in a Cabinet with Insufficient Front Clearance Figure 2-6 shows the Cisco MDS 9200 Series completely installed in a rack.
Chapter 2 Installing the Cisco MDS 9200 Series Installing the Switch in a Cabinet with Insufficient Front Clearance The rack-mount kit provided with the switch contains the items listed in Table 2-1. If you do not find all of the parts listed in Table 2-1, you may have an older version of the rack-mount kit, which only included the front rack-mount brackets.
Chapter 2 Installing the Cisco MDS 9200 Series Installing the Switch in a Cabinet with Insufficient Front Clearance Step 2 Install the C brackets on the switch as follows: a. Position one of the C brackets against the side of the switch and align the screw holes as shown in Figure 2-8 and Figure 2-9. Then attach the bracket to the switch with two of the flat-head M4 screws.
Chapter 2 Installing the Cisco MDS 9200 Series Installing the Switch in a Cabinet with Insufficient Front Clearance C Brackets for the Cisco MDS 9200 Series (Close-Up View) 94297 Figure 2-9 Note b. Ensure the C bracket is oriented so that it blocks the fewest airflow holes on the chassis; the holes should be slightly closer to the bottom of the brackets and the text on the back of the bracket should be right side up. Repeat with the other C bracket on the other side of the switch.
Chapter 2 Installing the Cisco MDS 9200 Series Installing the Switch in a Cabinet with Insufficient Front Clearance Figure 2-10 Front Rack-Mount Brackets (Rotated) Installed on the Cisco MDS 9200 Series MDS 9216i 1 2 3 4 5 6 7 8 GE1 9 11 GE2 LINK12 13 14 LINK- 116895 10 b. Step 2 Repeat with the other front rack-mount bracket on the other side of the switch. Install the C brackets on the switch as follows: a.
Chapter 2 Installing the Cisco MDS 9200 Series Installing the Switch in a Cabinet with Insufficient Front Clearance C Brackets for the Cisco MDS 9200 Series (Close-Up View) 94297 Figure 2-12 Note b. Ensure the C bracket is oriented so that it blocks the fewest airflow holes on the chassis; the holes should be slightly closer to the bottom of the brackets and the text on the back of the bracket should be right side up. Repeat with the other C bracket on the other side of the switch.
Chapter 2 Installing the Cisco MDS 9200 Series Installing the Switch in a Cabinet with Insufficient Front Clearance Note Figure 2-13 shows the front rack-mount brackets as rotated. Your chassis may have these brackets installed in the normal position.
Chapter 2 Installing the Cisco MDS 9200 Series Installing the Switch in a Cabinet with Insufficient Front Clearance Figure 2-14 Inserting and Installing Slider Rails (Front View) Rear cabinet mounting rails Front cabinet mounting rails 3 113444 2 1 1 Screws, 12-24 or 10-32 2 Slider rail 3 C bracket Figure 2-15 shows the Cisco MDS 9200 Series completely installed in a rack. Note Figure 2-15 shows the front rack-mount brackets as rotated.
Chapter 2 Installing the Cisco MDS 9200 Series System Grounding Figure 2-15 Cisco MDS 9200 Series Installed in the Rack (Back View) Front cabinet mounting rails Rear cabinet mounting rails MD 1 S 92 2 16 3 i 4 5 6 7 8 9 10 11 12 13 14 LIN K GE 1 K GE 2 116898 LIN System Grounding This section describes the need for system grounding and explains how to prevent damage from electrostatic discharge.
Chapter 2 Installing the Cisco MDS 9200 Series System Grounding Table 2-2 Grounding Best Practices Environment Commercial building is subjected to direct lightning strikes. Electromagnetic Noise Severity Level High All lightning protection devices must be installed in strict accordance with manufacturer recommendations. Conductors carrying lightning current should be spaced away from power and data lines in accordance with applicable recommendations and codes.
Chapter 2 Installing the Cisco MDS 9200 Series System Grounding Note In all situations, grounding practices must comply with local National Electric Code (NEC) requirements or local laws and regulations. Note Always ensure that all of the modules are completely installed and that the captive installation screws are fully tightened. In addition, ensure that all I/O cables and power cords are properly seated. These practices are normal installation practices and must be followed in all installations.
Chapter 2 Installing the Cisco MDS 9200 Series System Grounding Step 2 Grasp the spring or alligator clip on the ESD wrist strap and momentarily touch the clip to a bare metal spot (unpainted surface) on the rack. Cisco recommends that you touch the clip to an unpainted rack rail so that any built-up static charge is then safely dissipated to the entire rack. Step 3 Attach either the spring clip or the alligator clip to the ground lug screw as follows (See Figure 2-16.): a. Note b.
Chapter 2 Installing the Cisco MDS 9200 Series System Grounding In addition, follow these guidelines when handling modules: Caution • Handle carriers by available handles or edges only; avoid touching the printed circuit boards or connectors. • Place a removed component board-side-up on an antistatic surface or in a static shielding container. If you plan to return the component to the factory, immediately place it in a static shielding container.
Chapter 2 Installing the Cisco MDS 9200 Series Grounding the Chassis • Crimping tool to crimp the grounding wire to the grounding lug. • Wire-stripping tool to remove the insulation from the grounding wire. Grounding the Chassis The chassis has a grounding pad with two threaded M4 holes for attaching a grounding lug. Figure 2-17 shows the system ground location on the Cisco MDS 9200 Series.
Chapter 2 Installing the Cisco MDS 9200 Series Grounding the Chassis Figure 2-17 Location of System Ground on the Cisco MDS 9200 Series MD S 1 92 16 i 2 3 4 5 6 7 8 9 10 11 12 13 14 LIN K GE 1 LIN K 1 GE 2 2 3 6 116899 5 4 Warning Caution 1 ESD socket (on switch) 4 Screws, M4, with square cone washers 2 ESD plug 5 NRTL listed grounding lug 3 Grounding cable 6 Close-up of grounding pad on switch When installing or replacing the unit, the ground connection must always
Chapter 2 Installing the Cisco MDS 9200 Series Starting Up the Switch To attach the grounding lug and cable to the chassis, follow these steps: Step 1 Use a wire-stripping tool to remove approximately 0.75 in. (19 mm) of the covering from the end of the grounding cable. Step 2 Insert the stripped end of the grounding cable into the open end of the grounding lug. Step 3 Use the crimping tool to secure the grounding cable in the grounding lug.
Chapter 2 Installing the Cisco MDS 9200 Series Starting Up the Switch Step 2 Verify that both power supplies and the fan module are installed. Step 3 Verify that the power switches on both power supplies are off, and then plug the power cables into the power supplies and tighten the screws on the power cable retainers to ensure the cables cannot be pulled out.
Chapter 2 Installing the Cisco MDS 9200 Series Removing and Installing Components Note If you purchased this product through a Cisco reseller, contact the reseller directly for technical support. If you purchased this product directly from Cisco, contact Cisco Technical Support at this URL: http://www.cisco.com/warp/public/687/Directory/DirTAC.shtml. Step 10 Verify that the system software has booted and the switch has initialized without error messages.
Chapter 2 Installing the Cisco MDS 9200 Series Removing and Installing Components Warning Use of controls, adjustments, or performing procedures other than those specified may result in hazardous radiation exposure. Statement 1057 Warning Hazardous voltage or energy is present on the backplane when the system is operating. Use caution when servicing. Statement 1034 Caution To prevent ESD damage, wear grounding wrist straps during these procedures and handle modules by the carrier edges only.
Chapter 2 Installing the Cisco MDS 9200 Series Removing and Installing Components Figure 2-18 Positioning the Module in the Chassis Insert module between slot guides EMI gasket 3 4 1 2 6 MD S 1 92 16 i 2 3 4 5 6 7 8 9 10 11 12 13 14 LIN K GE 1 LIN K GE 2 EMI gasket DS-X9032 STATUS Ejector lever fully extended 117000 1/2 G FC Module Cisco MDS 9200 Series Hardware Installation Guide 2-30 OL-16188-01
Chapter 2 Installing the Cisco MDS 9200 Series Removing and Installing Components Figure 2-19 1 Clearing the EMI Gasket Amount of gap between the 1mm module EMI gasket and the module above it STATUS 2 Press down Press down MD S 1 92 16 i 2 3 4 5 6 7 8 9 10 11 12 13 14 LIN K GE 1 LIN GE 2 122001 K Removing a Caching Services Module Note A minimum of two CSMs in each fabric are required for redundancy and data backup.
Chapter 2 Installing the Cisco MDS 9200 Series Removing and Installing Components To remove a CSM module from the chassis, follow these steps: Step 1 Power off the module from the CLI. For information about the correct command to use, see the Cisco MDS 9000 Family CLI Configuration Guide. Step 2 Ensure that the backup process has completed by verifying that all LEDs on the module have turned off. This requires up to 10 minutes. Step 3 Loosen the two captive screws on the module.
Chapter 2 Installing the Cisco MDS 9200 Series Removing and Installing Components Warning Blank faceplates and cover panels serve three important functions: they prevent exposure to hazardous voltages and currents inside the chassis; they contain electromagnetic interference (EMI) that might disrupt other equipment; and they direct the flow of cooling air through the chassis. Do not operate the system unless all cards, faceplates, front covers, and rear covers are in place.
Chapter 2 Installing the Cisco MDS 9200 Series Removing and Installing Components MDS 9216i SY ST EM STA TU S Closing the Ejector Levers RE SE T Figure 2-20 CONSOLE MGMT 10/100 GE1 GE2 LINK- LINK- 1 1 2 3 4 5 6 7 8 9 10 11 12 13 COM1 14 STATUS LINK— —SPEED LINK— —SPEED LINK— —SPEED FAN STATUS 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 122003 2 FAN-MOD-2 Ejector levers flush with module faceplate Caution d. Note e.
Chapter 2 Installing the Cisco MDS 9200 Series Removing and Installing Components Maintaining a Caching Services Module Caution Note Maintenance should only be performed by qualified service personnel. A minimum of two CSMs in each fabric are required for redundancy and data backup.
Chapter 2 Installing the Cisco MDS 9200 Series Removing and Installing Components Removing and Installing Power Supplies The Cisco MDS 9200 Series supports dual 845-W AC power supplies that monitor output voltage and provide status to the supervisor module. This section includes the following topics: • Removing a Power Supply, page 2-36 • Installing a Power Supply, page 2-36 A flat-blade or Phillips screwdriver is required to perform these procedures.
Chapter 2 Installing the Cisco MDS 9200 Series Removing and Installing Components Figure 2-21 845-W AC Power Supply Front Panel 2 3 PWR-845-AC INPUT OK 1 FAN OK OUTPUT FAIL 5 94976 100-240V 12-5A 50/60 Hz ALL FASTENERS MUST BE FULLY ENGAGED PRIOR TO OPERATING OF POWER SUPPLY 4 Step 4 1 Power switch 4 AC power connection 2 Power cable retainer 5 Captive screw 3 Power supply LEDs Hold the power supply by the handle and orient it as shown in Figure 2-22, and then slide it into the power
Chapter 2 Installing the Cisco MDS 9200 Series Removing and Installing Components Caution In a system with dual power supplies, connect each power supply to a separate power source. In case of a power source failure, the second source will most likely still be available. Step 8 Turn the power switch to the on (|) position on the power supply. Step 9 Verify power supply operation by checking that the power supply LEDs are in the following states: • Input Ok LED is green. • Fan Ok LED is green.
Chapter 2 Installing the Cisco MDS 9200 Series Removing and Installing Components Figure 2-23 shows a fan module partially installed in the Cisco MDS 9200 Series. Figure 2-23 Fan Module MDS 9216i 1 2 3 4 5 6 7 8 GE1 9 10 1 2 3 GE2 LINK- 11 12 13 LINK- 14 4 5 6 7 8 9 10 11 12 14 15 16 122002 13 Removing a Fan Module Warning When removing the fan tray, keep your hands and fingers away from the spinning fan blades.
Chapter 2 Installing the Cisco MDS 9200 Series Removing and Installing Components Step 3 Listen for the fans if the switch is powered on. You should immediately hear them operating. If you do not hear them, ensure that the fan module is inserted completely in the chassis and the faceplate is flush with the outside surface of the chassis. Step 4 Verify that the Fan Status LED is green. If the LED is not green, one or more fans are faulty.
Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m CH A P T E R 3 Connecting the Cisco MDS 9200 Series The Cisco MDS 9200 Series provides the following types of ports: Caution • Console port (interface module)—An RS-232 port that you can use to create a local management connection. • COM1 port (interface module)—An RS-232 port that you can use to connect to an external serial communication device such as a modem.
Chapter 3 Connecting the Cisco MDS 9200 Series Preparing for Network Connections Preparing for Network Connections When preparing your site for network connections to the Cisco MDS 9200 Series, consider the following for each type of interface, and gather all the required equipment before connecting the ports: • Cabling required for each interface type • Distance limitations for each signal type • Additional interface equipment required Connecting to the Console Port The console port (labeled Conso
Chapter 3 Connecting the Cisco MDS 9200 Series Connecting to the Console Port Note To connect the console port to a computer terminal, the computer must support VT100 terminal emulation. The terminal emulation software—frequently an application such as HyperTerminal or Procomm Plus—makes communication between the Cisco MDS 9200 Series and a computer possible during setup and configuration.
Chapter 3 Connecting the Cisco MDS 9200 Series Connecting to the COM1 Port Connecting to the COM1 Port Note The COM1 port is not supported for connection to a console. The COM1 port (labeled COM1) is an RS-232 port with a DB-9 interface. (See Figure 3-2.) You can use this port to connect to an external serial communication device such as a modem.
Chapter 3 Connecting the Cisco MDS 9200 Series Connecting to the MGMT 10/100 Ethernet Port The default COM1 settings are as follows: line Aux: Speed: 9600 bauds Databits: 8 bits per byte Stopbits: 1 bit(s) Parity: none Modem In: Enable Modem Init-String default : ATE0Q1&D2&C1S0=1\015 Statistics: tx:17 rx:0 Register Bits:RTS|DTR Connecting to the MGMT 10/100 Ethernet Port Caution To prevent an IP address conflict, do not connect the MGMT 10/100 Ethernet port to the network until the initial configuration
Chapter 3 Connecting the Cisco MDS 9200 Series Connecting to a Fibre Channel Port Connecting to a Fibre Channel Port The Fibre Channel ports on the switch modules are compatible with LC-type fiber-optic SFP transceivers and cables. You can use the Fibre Channel ports to connect to the SAN or for in-band management. For information about configuring the switch for in-band management, see the Cisco MDS 9000 Family CLI Configuration Guide or the Cisco MDS 9000 Family Fabric Manager Configuration Guide.
Chapter 3 Connecting the Cisco MDS 9200 Series Connecting to a Fibre Channel Port The Cisco MDS 9000 Family supports X2 transceivers with SC connectors. (See Figure 3-4.
Chapter 3 Connecting the Cisco MDS 9200 Series Connecting to a Fibre Channel Port Installing an X2 Transceiver To install an X2 transceiver, follow these steps: Step 1 Attach an ESD-preventive wrist strap and follow its instructions for use. Caution If the transceiver does not install easily, ensure that it is correctly oriented before continuing. Step 2 Remove the dust cover from the port end of the transceiver. Step 3 Insert the transceiver into the port. ensure the transceiver is fully seated.
Chapter 3 Connecting the Cisco MDS 9200 Series Connecting to a Fibre Channel Port Note Use only Cisco SFP transceivers on the Cisco MDS 9200 Series. Each Cisco SFP transceiver is encoded with model information that enables the switch to verify that the SFP transceiver meets the requirements for the switch. For instructions specific to the transceiver type, see the “SFP Transceiver Specifications” section on page B-9.
Chapter 3 Connecting the Cisco MDS 9200 Series Connecting to a Fibre Channel Port If you cannot install the cable into the transceiver, insert or leave the dust plug in the cable end of the transceiver. Note Removing an SFP Transceiver To remove an SFP transceiver, follow these steps: Step 1 Attach an ESD-preventive wrist strap and follow its instructions for use. Step 2 If a cable is installed in the transceiver: a. Record the cable and port connections for later reference. b.
Chapter 3 Connecting the Cisco MDS 9200 Series Connecting to a Fibre Channel Port Alternate Removal Method for Bale Clasp SFP Transceivers 115237 Figure 3-7 Step 4 Insert a dust cover into the port end of the transceiver and place the transceiver on an antistatic mat or into a static shielding bag if you plan to return it to the factory. Step 5 If another transceiver is not being installed, protect the optical cage by inserting a clean cover.
Chapter 3 Connecting the Cisco MDS 9200 Series Connecting to a Fibre Channel Port Figure 3-8 Connecting the LC-Type Cable to a Fibre Channel Port LC plug 91681 SFP module Caution If the cable does not install easily, ensure that it is correctly oriented before continuing. For instructions on verifying connectivity, see the Cisco MDS 9000 Family CLI Configuration Guide or the Cisco MDS 9000 Family Fabric Manager Configuration Guide.
Chapter 3 Connecting the Cisco MDS 9200 Series Connecting to a Fibre Channel Port Maintaining SFP Transceivers and Fiber-Optic Cables SFP transceivers and fiber-optic cables must be kept clean and dust-free to maintain high signal accuracy and prevent damage to the connectors. Attenuation (Loss of Light) is increased by contamination and should be below 0.35 dB. Consider the following maintenance guidelines: • SFP transceivers are static sensitive.
Chapter 3 Connecting the Cisco MDS 9200 Series Connecting to a Fibre Channel Port Cisco MDS 9200 Series Hardware Installation Guide 3-14 OL-16188-01
Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o .
Appendix A Cabinet and Rack Installation Cabinet and Rack Requirements The cabinet or rack must also meet the following requirements: • The minimum vertical rack space per chassis must be three RU (rack units), equal to 5.25 in. (13.3 cm). • The width between the rack-mounting rails must be at least 17.75 in. (45.1 cm) if the rear of the switch is not attached to the rack. For four-post EIA racks, this is the distance between the two front rails.
Appendix A Cabinet and Rack Installation Cabinet and Rack Requirements Requirements Specific to Solid-Walled Cabinets A solid-walled cabinet is defined here as a cabinet with solid front and rear doors and solid side walls.
Appendix A Cabinet and Rack Installation Cisco MDS 9000 Family telco and EIA Shelf Bracket Cisco MDS 9000 Family telco and EIA Shelf Bracket The optional telco and EIA Shelf Bracket Kit (part number DS-SHELF=) can temporarily or permanently support the Cisco MDS 9200 Series during installation. Once the front rack-mount brackets are securely attached to the rack-mounting rails, the shelf bracket can be removed.
Appendix A Cabinet and Rack Installation Cisco MDS 9000 Family telco and EIA Shelf Bracket • The rack has sufficient vertical clearance for the chassis plus 2 RU for the shelf brackets, and any desired clearance for the installation process. • The rack meets the minimum rack load ratings per rack unit listed in the following table: Rack Type MDS 9513 MDS 9509 MDS 9506 MDS 9222i MDS 9216i MDS 9216A EIA (4-Post) 45 lb (20.41 kg) 45 lb (20.41 kg) 30 lb (13.61 kg) 15 lb (6.8 kg) 7.5 lb (3.
Appendix A Cabinet and Rack Installation Cisco MDS 9000 Family telco and EIA Shelf Bracket Installing the Shelf Bracket Kit into a Two-Post telco Rack Figure A-1 shows the installation of the shelf bracket kit into a two-post telco rack.
Appendix A Cabinet and Rack Installation Cisco MDS 9000 Family telco and EIA Shelf Bracket Installing the Shelf Bracket Kit into a Four-Post EIA Rack Figure A-2 shows the installation of the shelf bracket kit into a four-post EIA rack.
Appendix A Cabinet and Rack Installation Cisco MDS 9000 Family telco and EIA Shelf Bracket Step 4 Attach the crossbar to the shelf brackets as shown in Figure A-2, using the 10-32 screws. Step 5 Insert the slider rails into the shelf brackets as shown in Figure A-2. Then, attach them to the rear rack-mounting rails using a minimum of four 12-24 or 10-24 screws.
Appendix A Cabinet and Rack Installation Cisco MDS 9000 Family telco and EIA Shelf Bracket Removing the Shelf Bracket Kit (Optional) The shelf bracket kit can be removed once the Cisco MDS 9200 Series has been installed in a two-post telco or four-post EIA rack, and the front rack-mount brackets are securely attached to the rack-mounting rails. For additional support in an EIA rack, ensure that the C brackets on the Cisco MDS 9200 Series are attached to the rear rack-mounting rails.
Appendix A Cabinet and Rack Installation Cisco MDS 9000 Family telco and EIA Shelf Bracket Cisco MDS 9200 Series Hardware Installation Guide A-10 OL-16188-01
Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m A P P E N D I X B Technical Specifications This appendix includes the following sections: Note • Switch Specifications, page B-1 • Module Specifications, page B-2 • Power Specifications, page B-4 • X2 Transceiver Specifications, page B-6 • SFP Transceiver Specifications, page B-9 Specifications for cables and connectors are provided in Appendix C, “Cable and Port Specifications.
Appendix B Technical Specifications Module Specifications Table B-2 lists the physical specifications for the Cisco MDS 9200 Series. Table B-2 Physical Specifications for the Cisco MDS 9200 Series Description Specification Dimensions (HxWxD) 5.25 x 17.5 x 22.75 in. (13.3 x 44.5 x 57.8 cm) Chassis requires 3 RU1. Chassis depth including cable guide is 27.75 in. (70.3 cm). Weight Chassis only: 31 lb (14.1 kg). Chassis configured with one supervisor module, fan module, and two power supplies: 53.
Appendix B Technical Specifications Module Specifications Table B-3 Cisco MDS 9200 Series Module Specifications (continued) Description Specification Altitude, designed and tested for operation -200 to 10000 ft (-60 to 3000 m) Physical Characteristics Dimensions 1.75 x15.5 x16.5 in. (4.4 x 39.4 x 41.9 cm) Note Weight These are the maximum dimensions of faceplate and board, and include connectors on board. 8 to 11.5 lb (1.4 to 5.
Appendix B Technical Specifications Power Specifications Table B-5 Weight of Modules in the Cisco MDS 9000 Family (continued) Module Weight CSM 11.5 lb (5.2 kg) ASM 11 lb (5 kg) IPS-8 10 lb (4.5 kg) IPS-4 9 lb (4.1 kg) MSM-18/4 8.5 lb (3.86 kg) MSFM-18/4 8.5 lb (3.86 kg) MPS-14/2 10 lb (4.5 kg) Supervisor-2 for MDS 9500 Series 7.25 lb (kg) Supervisor-1 for MDS 9500 Series 9 lb (4.1 kg) Supervisor for MDS 9200 Series 9 lb (4.1 kg) Module blank panels 0.50 lb (0.
Appendix B Technical Specifications Power Specifications Component Power Requirements and Heat Dissipation Specifications Consider heat dissipation when sizing the air-conditioning requirements for an installation.
Appendix B Technical Specifications X2 Transceiver Specifications Table B-7 Power Requirements and Heat Dissipation for the 845-W Power Supply (continued) SAN-OS Release Input Current Power Heat Required Dissipation 90 VAC 120 VAC (watts) (BTU/hr) (amps) (amps) 180 VAC (amps) 240 VAC (amps) 32-port 1-Gbps/2-Gbps Fibre Channel module, DS-X9032 3.x 191 816 2.65 1.99 1.33 0.99 2.x and 1.x 200 855 2.78 2.08 1.39 1.04 16-port 1-Gbps/2-Gbps Fibre Channel module, DS-X9016 3.x 210 897 2.
Appendix B Technical Specifications General Specification for Cisco 10-Gbps Fibre Channel X2 Transceivers Cisco 10-Gbps Fibre Channel X2 Transceivers Table B-8 lists the Cisco10-Gbps Fibre Channel X2 transceivers.
Appendix B Technical Specifications General Specification for Cisco 10-Gbps Fibre Channel X2 Transceivers Note DS-X2-FC10G-CX4 is not an optical module; therefore, it is not listed in Table B-10. Table B-11 provides the environmental specifications for the Cisco 10-Gbps Fibre Channel X2 transceivers.
Appendix B Technical Specifications SFP Transceiver Specifications Environmental and Power Requirements Specifications for Cisco 10-Gbps Ethernet X2 Transceiver Table B-14 provides the power requirement specifications for the Cisco 10-Gbps Ethernet X2 transceiver. Table B-14 Power Requirement Specification for Cisco 10-Gbps Ethernet X2 Transceivers Average Transmit Power (dBm) Average Receive Power (dBm) Fiber Loss Budget (dBm) X2 Maximum Minimum Maximum Minimum DS-X2-E10G-SR -1.2 -7.3 -1.
Appendix B Technical Specifications SFP Transceiver Specifications Cisco Fibre Channel SFP Transceivers Table B-16 lists the Cisco 2-Gbps and 4-Gbps Fibre Channel SFP transceivers.
Appendix B Technical Specifications SFP Transceiver Specifications Environmental and Power Requirement for Cisco 4-Gbps Fibre Channel SFP Transceivers Table B-18 provides the power specification for the Cisco 4-Gbps Fibre Channel SFP transceivers. Table B-18 Power Requirement Specification for Cisco 4-Gbps Fibre Channel SFP Transceivers Average Transmit Power (dBm) Average Receive Power (dBm) Maximum Minimum Maximum Minimum DS-SFP-FC4G-SW -1.2 -9 0 – 1.78 (62.5 micron), 2.
Appendix B Technical Specifications SFP Transceiver Specifications General Specifications for Cisco 2-Gbps Fibre Channel SFP Transceivers Table B-20 provides general specification for the 4-Gbps Fibre Channel SFP transceiver. Table B-20 General Specifications for Cisco 4-Gbps Fibre Channel SFP Transceivers SFP Wavelength (nanometer) Fibre Type Core Size (micon) Baud Rate (GBd) Cable Distance (meter) DS-SFP-FC-2G-SW 850 62.5 1.0625 300 m (984 ft) 62.5 2.125 150 m (492 ft) 50.0 (OM2) 1.
Appendix B Technical Specifications SFP Transceiver Specifications Maximum Environmental and Electrical Ratings for Cisco Fibre Channel SFP Transceivers Table B-23 provides the maximum environmental and electrical ratings for Cisco Fibre Channel SFP transceivers. Table B-23 Maximum Environmental and Electrical Ratings for Cisco Fibre Channel SFP Transceivers Parameter1 Symbol Min. Max.
Appendix B Technical Specifications SFP Transceiver Specifications General Specifications for Cisco Fibre Channel/Gigabit Ethernet SFP Transceivers Table B-25 provides general specification for Cisco Fibre Channel/Gigabit Ethernet SFP transceiver. Table B-25 General Specifications for Cisco Fibre Channel/Gigabit Ethernet SFP Transceivers SFP Wavelength (nanometer) Fibre Type Core Size (micon) Baud Rate (GBd) Cable Distance (meter) DS-SFP-FCGE-SW 850 62.5 1.0625 300 m (984 ft) 62.5 2.
Appendix B Technical Specifications SFP Transceiver Specifications Table B-27 provides the environmental specification for Cisco Fibre Channel/Gigabit Ethernet SFP transceivers.
Appendix B Technical Specifications SFP Transceiver Specifications Table B-29 lists the Cisco 4-Gbps CWDM SFP transceivers available through Cisco.
Appendix B Technical Specifications SFP Transceiver Specifications Table B-31 provides the optical specifications for the Cisco 2-Gbps CWDM SFP transceivers.
Appendix B Technical Specifications SFP Transceiver Specifications Environmental and Optical Specifications for Cisco 4-Gbps CWDM SFP Transceivers Table B-32 provides the environmental specifications for the Cisco 4-Gbps CWDM SFP transceivers.
Appendix B Technical Specifications SFP Transceiver Specifications • When interoperating a Cisco 4-Gbps CWDM SFP transceiver with a Cisco 1/2-Gbps CWDM transceiver, the speed of ports on the Cisco 4-Gbps CWDM SFP transceiver must be manually configured to 1-Gbps or 2-Gbps. For information about safety, regulatory, and standards compliance, refer to the Regulatory Compliance and Safety Information for the Cisco MDS 9000 Family.
Appendix B Technical Specifications SFP Transceiver Specifications DWDM Fibre Channel SFP Transceivers Fibre Channel ports on the Cisco MDS 9222i support 2-Gbps DWDM SFP transceivers. Table B-37 lists the DWDM Fibre Channel transceivers supported on the Cisco MDS 9200 Series. Note A maximum of eight 2-Gbps DWDM SFPs are supported in a single MDS switching module.
Appendix B Technical Specifications SFP Transceiver Specifications Table B-37 Supported DWDM Fibre Channel SFP Transceivers for Cisco MDS 9200 Series Part Number Product Name DWDM-SFP-3190 Cisco 3190 nm; DWDM 1/2-Gbps Fibre Channel SFP DWDM-SFP-3112 Cisco 3112 nm; DWDM 1/2-Gbps Fibre Channel SF DWDM-SFP-3033 Cisco 3033 nm; DWDM 1/2-Gbps Fibre Channel SF Cisco MDS 9200 Series Hardware Installation Guide OL-16188-01 B-21
Appendix B Technical Specifications SFP Transceiver Specifications Cisco MDS 9200 Series Hardware Installation Guide B-22 OL-16188-01
Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o .
Appendix C Cable and Port Specifications Console Port Console Port The console port is an asynchronous RS-232 serial port with an RJ-45 connector. You can use the RJ-45 rollover cable and the RJ-45/DSUB F/F adapter or the DB-9F/RJ-45F PC terminal adapter to connect the console port to a computer running terminal emulation software. Console Port Pinouts Table C-1 lists the pinouts for the console port on the Cisco MDS 9500 Series.
Appendix C Cable and Port Specifications COM1 Port Connecting the Console Port to a Computer Using the DB-9 Adapter You can use the RJ-45 rollover cable and DB-9F/RJ-45F PC terminal (labeled “Terminal”) to connect the console port to a computer running terminal emulation software. Table C-3 lists the pinouts for the console port, the RJ-45 rollover cable, and the DB-9F/RJ-45F PC terminal.
Appendix C Cable and Port Specifications COM1 Port COM1 Port Pinouts Table C-4 lists the pinouts for the COM1 port on the Cisco MDS 9500 Series. Note Additional cables and adapters can be ordered from your customer service representative.
Appendix C Cable and Port Specifications MGMT 10/100/1000 Ethernet Port Table C-5 lists the pinouts for the COM1 port, the DB-9F/RJ-45F PC terminal, RJ-45 rollover cable, and the RJ-45/DSUB R/P adapter.
Appendix C Cable and Port Specifications MGMT 10/100 Ethernet Port Table C-6 10/100/1000BASE-T Management Port Cable Pinout (MDI) (continued) Pin Signal 3 RD+ 6 RD– 4 Not used 5 Not used 7 Not used 8 Not used Figure C-2 shows a schematic of the 10/100/1000BASE-T cable required to connect the management port to a switch or hub (not provided with the switch).
Appendix C Cable and Port Specifications MGMT 10/100 Ethernet Port Figure C-7 lists the connector pinouts and signal names for a 10/100BASE-T management port (MDI) cable. Table C-7 Note 10/100BASE-T Management Port Cable Pinout (MDI) Pin Signal 1 TD+ 2 TD- 3 RD+ 6 RD– 4 Not used 5 Not used 7 Not used 8 Not used The RJ-45 interface only uses pins 1, 2, 3, and 6.
Appendix C Cable and Port Specifications Supported Power Cords and Plugs Supported Power Cords and Plugs Each power supply has a separate power cord. Standard power cords or jumper power cords are available for connection to a power distribution unit having IEC 60320 C19 outlet receptacles. The jumper power cords, for use in cabinets, are available as an optional alternative to the standard power cords. Power Cords The standard power cords have an IEC C19 connector on the end that plugs into the switch.
Appendix C Cable and Port Specifications Supported Power Cords and Plugs Supported Plugs for 6000-W AC, 2500-W AC, and 1900-W AC Power Supplies Figure C-5 shows the supported plugs for the 6000-W AC, 3000-W AC, 2500-W AC, and 1900-W AC power supplies.
Appendix C Cable and Port Specifications Supported Power Cords and Plugs Figure C-6 shows an additional plug that is supported for the 1900-W AC power supply only. Additional Power Supply Plug Supported for 1900-W Only 113147 Figure C-6 1 United Kingdom BS89/13, BS 1363/A (13 A; replaceable fuse) Figure C-7 shows an additional plug that is supported for the 3000-W and 2500-W power supply, using 110 VAC. Note Using the plug in Figure C-7 at 110 VAC results in 1300 W available to the system.
Appendix C Cable and Port Specifications Supported Power Cords and Plugs Supported Plugs for the 4000-W AC Power Supply Figure C-8 shows the supported plugs for the 4000-W AC power supply. The power cable on the 4000 W power supply is nondetachable.
Appendix C Cable and Port Specifications Supported Power Cords and Plugs Cisco MDS 9200 Series Hardware Installation Guide C-12 OL-16188-01
Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o .
Appendix D Site Planning and Maintenance Records Site Preparation Checklist Table D-1 Site Planning Checklist Task No.
Appendix D Site Planning and Maintenance Records Contact and Site Information 3. EMI = electromagnetic interference. 4. RFI = radio frequency interference. Contact and Site Information Use the following worksheet (Table D-2) to record contact and site information.
Appendix D Site Planning and Maintenance Records Chassis and Module Information Chassis and Module Information Use the following worksheets (Table D-3 and Table D-4) to record information about the chassis and modules.
Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m .
Index Caching Services Module.
Index F I fan modules installing description figure equipment required 1-34 2-39 installing (procedure) LEDs 2-39 rack-mount (front-facing) 2-7 rack-mount (rear-facing) 2-16 rack-mount (rotated brackets) 1-34 removing (procedure) Fiber Connectivity 2-39 1-20 fiber optic cables 2-9 rack-mount rear-facing (figure) 2-17 3-11 SFP transceivers (note) 3-13 Fibre Channel/Gigabit Ethernet SFP transceivers Fibre Channel ports X2 transceivers 1-35 2-14 rack-mount front-facing (figure) S
Index ports M COM1 maintaining 3-4 console 3-2 fiber optic cables 3-13 Fibre Channel SFP transceivers 3-13 MGMT 10/100 maintenance records D-1 potting MGMT 10/100/1000 Ethernet port 3-5 3-5 1-20 power cord, jumper C-12 cabling C-5 power cords, length C-8 pinouts C-5 power-on MGMT 10/100 Ethernet port cabling C-6 3-5 connecting (procedure) description 3-5 figure C-6 1-33 1-33 installing (procedure) MPS-14/2 figure LED (table) 1-23 LEDs (table) 1-27 power supplies con
Index removing SFP transceivers chassis from rack 2-40 SFP transceiver cables SFP transceivers X2 transceivers 3-12 cabling 3-11, 3-12 CWDM 1-36, B-15 description 3-10 1-35, 1-36, 3-8, B-9 Fibre Channel 3-8 1-35 Fibre Channel/Gigabit Ethernet 1-35 Fibre Channel/Gigabit Ethernet supported S Fibre Channel specifications Fibre Channel supported self-test passed front panel LEDs Gigabit Ethernet 1-27 installing self-test running front panel LEDs 1-27 services modules ASM downloading
Index SSM T description figure 1-26 Table 1-26 starting up the switch telco racks (requirements) 2-26 Cisco MDS 9216A Cisco MDS 9216i 1-7 1-7 W 2-28 LEDs (table) weight of modules (table) 1-9 power and heat specification removing B-3 B-5 2-31, 2-32 specifications A-4 transceivers, supported SFPs.
