Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Cisco MDS 9000 Family System Messages Reference Cisco MDS 9000 SAN-OS Release 3.3(1a) April 2008 Americas Headquarters Cisco Systems, Inc. 170 West Tasman Drive San Jose, CA 95134-1706 USA http://www.cisco.
Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m THE SPECIFICATIONS AND INFORMATION REGARDING THE PRODUCTS IN THIS MANUAL ARE SUBJECT TO CHANGE WITHOUT NOTICE. ALL STATEMENTS, INFORMATION, AND RECOMMENDATIONS IN THIS MANUAL ARE BELIEVED TO BE ACCURATE BUT ARE PRESENTED WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED. USERS MUST TAKE FULL RESPONSIBILITY FOR THEIR APPLICATION OF ANY PRODUCTS.
Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o .
Contents Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o .
Contents Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o .
Contents Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o .
Contents Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o .
Contents Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o .
Contents Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o .
Contents Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o .
Contents Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o .
Contents Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o .
Contents Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o .
Contents Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o .
Contents Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o .
Contents Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o .
Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m New and Changed Information Table 1 summarizes the new and changed features supported by messages described in this version of the Cisco MDS 9000 Family System Messages Reference. For more information about a specific feature, refer to the Cisco MDS 9000 Family CLI Configuration Guide and Cisco MDS 9000 Family Fabric Manager Configuration Guide.
New and Changed Information Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Table 1 New and Changed Features and Related System Messages Feature Description CFS, IPS, IVR, LICMGR Added messages for CFS, IP services, IVR, and the license Manager Changed in Release Where Documented 3.
New and Changed Information Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Table 1 New and Changed Features and Related System Messages Feature Description Changed in Release Where Documented DEVICE-ALIAS Supports DEVICE-ALIAS messages. 2.0(1b) “DEVICE-ALIAS Messages” section on page 2-37 Dynamic Port Supports DPVM messages. VSAN Membership (DPVM) 2.0(1b) “DPVM Messages” section on page 2-45 DSTATS Supports DSTATS messages. 2.
New and Changed Information Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o .
Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Preface This document lists and describes the system messages for the Cisco MDS 9000 Family of directors and multilayer fabric switches. The system software sends these messages to the console (and, optionally, to a logging server on another system) during operation. Not all messages indicate a problem with your system.
Preface Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Document Conventions This document uses the following conventions: Note Caution Means reader take note. Notes contain helpful suggestions or references to material not covered in the manual. Means reader be careful. In this situation, you might do something that could result in equipment damage or loss of data.
Preface Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m For information on IBM TotalStorage SAN Volume Controller Storage Software for the Cisco MDS 9000 Family, refer to the IBM TotalStorage Support website: http://www.ibm.
Preface Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o .
Preface Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m You can access the Cisco website at this URL: http://www.cisco.com You can access international Cisco websites at this URL: http://www.cisco.com/public/countries_languages.shtml Product Documentation DVD The Product Documentation DVD is a comprehensive library of technical product documentation on a portable medium.
Preface Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m http://www.cisco.com/en/US/products/products_security_vulnerability_policy.html From this site, you will find information about how to: Report security vulnerabilities in Cisco products. Obtain assistance with security incidents that involve Cisco products. Register to receive security information from Cisco.
Preface Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Obtaining Technical Assistance Cisco Technical Support provides 24-hour-a-day award-winning technical assistance. The Cisco Technical Support & Documentation website on Cisco.com features extensive online support resources. In addition, if you have a valid Cisco service contract, Cisco Technical Assistance Center (TAC) engineers provide telephone support.
Preface Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m For a complete list of Cisco TAC contacts, go to this URL: http://www.cisco.com/techsupport/contacts Definitions of Service Request Severity To ensure that all service requests are reported in a standard format, Cisco has established severity definitions. Severity 1 (S1)—An existing network is down, or there is a critical impact to your business operations.
Preface Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m • iQ Magazine is the quarterly publication from Cisco Systems designed to help growing companies learn how they can use technology to increase revenue, streamline their business, and expand services.
Preface Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o .
Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m CH A P T E R 1 Introduction to System Messages for the Cisco MDS 9000 Family This chapter describes system messages, as defined by the syslog protocol (RFC 3164). It describes how to understand the syslog message format and how to capture system messages for review.
Chapter 1 Introduction to System Messages for the Cisco MDS 9000 Family System Log Message Format Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o .
Chapter 1 Introduction to System Messages for the Cisco MDS 9000 Family System Log Message Format Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o .
Chapter 1 Introduction to System Messages for the Cisco MDS 9000 Family Capturing System Messages and History Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m System message SEVERITY codes range from 0 to 3 and reflect the severity of the condition. The lower the number, the more serious the situation. Table 1-4 lists the severity levels.
Chapter 1 Introduction to System Messages for the Cisco MDS 9000 Family Capturing System Messages and History Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Fabric Manager Configuration Guide). Only system messages that correspond to the configured logging level or higher severity messages are logged.
Chapter 1 Introduction to System Messages for the Cisco MDS 9000 Family Capturing System Messages and History Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o .
Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m CH A P T E R 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family This chapter lists messages according to the same system facility that produces the messages. Messages are listed in alphabetical order, by system facility. Within each system facility section, messages are listed alphabetically by severity and mnemonics.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o .
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o .
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o .
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Introduced Cisco MDS SAN-OS Release 1.3(1). AAA-2 Error Message [chars]. AAA-2-AAA_NVRAM_UPGRADE_FAILURE: upgrading of accounting log failed. The accounting log could not be upgraded because of a problem with NVRAM. The problem is described in the error message.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m ACL-2 Error Message [chars]. ACL-2-ACL_HA_FAILURE: Failed to do high availability operation: Explanation The high availability operation failed because of the reason shown in the error message. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.2(2a).
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message ACL-2-ACL_MTS_FAILURE: Failed to do MTS operation: [chars]. The messaging and transaction service (MTS) operation failed because of the reason shown in the error message. Explanation Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.2(2a).
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message ACL-2-ACL_TCAM_FAILURE: Failed to do TCAM operation: [chars]. The ternary content addressable memory (TCAM) operation failed because of the reason shown in the error message. Explanation Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.2(2a).
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message Explanation ACL-6-ACL_FCC_EVENT_STATUS: [chars] [chars]. This message reports the ACL Fibre Channel Congestion Control (FCC) event status. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.2(2a). Error Message ACL-6-ACL_LINECARD_EVENT_STATUS: [chars] [hex].
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Introduced Cisco MDS SAN-OS Release 1.2(2a). Error Message Explanation ACL-6-ACL_SPAN_SRC_CONFIG_STATUS: [chars] [chars]. This message reports the ACL SPAN source configuration event status. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.2(2a).
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message ACLTCAM-2-ACL_TCAM_INCONSISTENT_DATABASE: Database found inconsistent. Explanation The database is in an inconsistent state. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.2(2a). Error Message ACLTCAM-2-ACL_TCAM_INCONSISTENT_TCAM_CONTENTS: TCAM contents found inconsistent.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message ACLTCAM-2-ACL_TCAM_MTS_REGISTRATION_FAILED: MTS registration failed for opCode: [dec]. Explanation The messaging and transaction service (MTS) registration failed for the reason shown in the error message. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.2(2a).
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message ACLTCAM-2-ACL_TCAM_PSS_FAILURE: Failed to do PSS operation: [chars], reason: [hex]. Failed to do a persistent storage service (PSS) operation because of the reason shown in the error message. Explanation Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.3(1).
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m ASCII-CFG Messages This section contains the ASCII configuration (ASCII-CFG) messages. ASCII-CFG-2 Error Message ASCII-CFG-2-ACFG_CONFIGURATION_APPLY_ERROR: Error encountered while Ascii configuration was being applied. Explanation At least one command failed while ASCII configuration was being applied.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message BIOS_DAEMON-SLOT#-2-BIOS_DAEMON_LC_ERROR: BIOS Sector ([dec]) is write protected Explanation The BIOS on the module is write protected. If you purchased Cisco support through a Cisco reseller, contact the reseller directly. If you purchased support directly from Cisco Systems, contact Cisco Technical Support.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message Explanation BOOTVAR-2-CONFIG_ERROR: Failed to update boot configuration. An error has occurred during the update of the boot configuration files. Recommended Action Ensure that there is enough space on the flash.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message BOOTVAR-3-LOAD_VERIFY_LIB_FAILED: Fetching library [chars] failed, reason=[chars]. Explanation The boot variable verification library specified failed to load. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.2(2a).
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message BOOTVAR-5-AUTOCOPY_VERIFY_SEND_FAILED: Unable to ask standby to verify file [chars], error = [hex]. Explanation After copying the image to the standby supervisor, the active supervisor failed to verify the integrity of that image on the standby supervisor. Recommended Action Turn auto-copy off and back on.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Introduced Cisco MDS SAN-OS Release 1.3(4a). BOOTVAR-6 Error Message Explanation BOOTVAR-6-ALREADY_IN_SYNC: Image already in sync. No need to update the image on the standby supervisor. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.2(2a).
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message Explanation CALLHOME-2-PROGRAM_EXIT: callhome process ending: [chars]. Call Home process is exiting because of the reason shown in the error message. If you purchased Cisco support through a Cisco reseller, contact the reseller directly.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message CALLHOME-3-MESSAGE_SIZE_EXCEED: message size for callhome alert:[chars] exceeds maximum limit for destination profile:[chars]. Explanation The message size for the Call Home alert exceeds the maximum limit for the destination profile shown in the error message.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message CDP-3-GENERROR: [chars]. Explanation The Cisco Discovery Protocol daemon encountered a general error, one that does not fall in any of the above categories. The error message describes the error and its context. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.2(2a).
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message [chars]. CDP-3-SOCKBINDFAIL: Failed to bind to raw socket, interface [hex] - Explanation The Cisco Discovery Protocol failed to bind to a raw socket. The error message identifies the interface and the reason for this failure. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message CDP-6-PORTDOWN: A CDP enabled port [chars] went down. A Cisco Discovery Protocol enabled port became unoperational. The error message shows the Interface-ID string that identifies the port. Explanation Recommended Action This is an informational message. Introduced Cisco MDS SAN-OS Release 1.2(2a).
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message CERT_ENROLL-3-CERT_EN_FIPS_MODE_INIT_ERROR: Could not initialize FIPS mode : [chars]. Explanation FIPS mode initialization error. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 3.1(1). Error Message CERT_ENROLL-6-CERT_EN_MESSAGE: [chars].
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message CFS-2-GENERAL_ERROR: [chars]. Explanation The Cisco Fabric Services process has encountered a critical error. The description of error is shown in the error message. Recommended Action Refer to the listed error and take action as required. Introduced Cisco MDS SAN-OS Release 2.0(1b).
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m CFS-3 Error Message CFS-3-ALLOCFAIL: Heap Memory allocation failed: [chars]. Explanation The Cisco Fabric Services process is out of dynamic memory. The error message specifies the context where the failure occurred. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 2.0(1b).
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Introduced Cisco MDS SAN-OS Release 2.0(1b). Error Message CFS-3-GENERROR: [chars]. Explanation The Cisco Fabric Services encountered a general error, one that does not fall in any of the above categories. The error message describes the error and its context. Recommended Action No action is required.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Introduced Cisco MDS SAN-OS Release 2.0(1b). CFS-4 Error Message CFS-4-LICEXP: [chars]. Explanation The Cisco Fabric Services license is going to expire. The error message shows the expiration time. Recommended Action Install a license. Introduced Cisco MDS SAN-OS Release 2.0(1b).
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message CFS-6-FAILED_TO_SEND_HEARTBEAT: Failed to send heartbeat to system manager: Reason=[chars]. Explanation The Cisco Fabric Services failed to send a heartbeat message to the system manager. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 2.0(1b).
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message CFS-6-PSS_DESTROYED: [chars] PSS Destroyed. Explanation A persistent information database for Cisco Fabric Services has been deleted and will be recreated. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 2.0(1b).
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m CIMSRVPROV Messages This section contains the Common Information Model (CIM) server (CIMSRVPROV) messages. CIMSRVPROV-2 Error Message Explanation CIMSRVPROV-2-CIM_SYSLOG_EXIT: Message:[chars] errcode:[dec]. The CIM server exited because of a critical error. Recommended Action No action is required.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message CIMSRVPROV-3-CIM_SYSLOG_MTS_ERR: message [chars]. Explanation The CIM server experienced a messaging and transaction service (MTS) message handling error. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.3(1).
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m CLOUD-3 Error Message CLOUD-3-CLOUD_CFS_MERGE_OPERATION_FAILED: [chars]. CFS merge failed. Explanation Recommended Action Check the message for the reason for failure of the CFS operation and rectify the problem. Introduced Cisco MDS SAN-OS Release 3.0(1).
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message CLOUD-6-CLOUD_DISCOVERY_STARTED: Explanation [chars] discovery started. Cloud-discovery started. Get more information using the cloud-discovery status CLI command. You can alternatively use Fabric Manager and/or Device Manager instead of the command line method. Introduced Cisco MDS SAN-OS Release 3.0(1).
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Introduced Cisco MDS SAN-OS Release 3.0(1).
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m DEBUGPROXY Messages This section contains the debug proxy (DEBUGPROXY) messages. DEBUGPROXY-6 Error Message Explanation DEBUGPROXY-6-ILC_DEBUG_PROXY_COMMON: ilc debug proxy [chars] [dec]. General intelligent line card (ILC) debug proxy information. Recommended Action No action is required.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m DEVICE-ALIAS-3 Error Message DEVICE-ALIAS-3-CFS_OPER_FAILED: [chars]. Explanation An error occurred while performing a Cisco Fabric Services (CFS) operation. The error message indicates the CFS operation and the reason for failure. If you purchased Cisco support through a Cisco reseller, contact the reseller directly.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message DEVICE-ALIAS-3-LOCK_REJECTED: [chars]. Explanation Lock request received from a remote switch is rejected. The error message indicates the reason for the failure. If you purchased Cisco support through a Cisco reseller, contact the reseller directly.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message DEVICE-ALIAS-3-PSS_OPER_FAILED: [chars]. An error occurred during a persistent storage service (PSS) operation. The error message indicates the persistent storage service (PSS) operation and the reason for failure.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message DEVICE-ALIAS-6-IMPORT_DEFINITION_CONFLICT: Fcalias [chars] could not be imported due to definition conflict. Explanation The fcalias shown could not be imported because of a definition conflict.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message DEVICE-ALIAS-6-LOCK_FAILED_INFO: [chars]. Explanation An error occurred while acquiring the lock. The error message indicates the additional information regarding failure. If you purchased Cisco support through a Cisco reseller, contact the reseller directly.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m DMM-SLOT# Messages DMM-SLOT#-5 Error Message DMM-SLOT#-5-LOG_ERR_DMM_NEW_NPORT_SRVR_ZONE: Job Id:%Ld VSAN :[dec] New N-Port FCID :[hex] Server FCID:[hex] are in the same zone. ALERT!!. Explanation A new N port has come up, which is zoned in the same zone as the server. Recommended Action No action is required.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message DMM-SLOT#-5-LOG_EV_DMM_JOB_ERROR: Job Id:%Ld NumSession:[dec]. Explanation Event indicating the suspension of data migration job. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 3.2(1).
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message DMM-SLOT#-5-LOG_EV_DMM_JOB_VERIFY_START: Job Id:%Ld NumSession:[dec]. Explanation Event indicating the start of a data migration job verification. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 3.2(1).
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message Explanation DPVM-2-FEATURE_DISABLED: [chars]. The dynamic port VSAN membership feature is unavailable and disabled. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 2.0(1b). Deprecated Cisco MDS SAN-OS Release 2.0(2b). Error Message DPVM-2-FEATURE_ENABLED: [chars].
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message DPVM-3-MTS_ERR: [chars]. An error occurred in processing a messaging and transaction service (MTS) message. The error message indicates the error that occurred. Explanation If you purchased Cisco support through a Cisco reseller, contact the reseller directly.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message DPVM-6-INFO: [chars]. Explanation An event occurred that affects the dynamic port VSAN membership. The error message indicates the event. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 2.0(1b). DSTATS Messages This section contains the DSTATS messages.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Introduced Cisco MDS SAN-OS Release 2.0(1b). Error Message DSTATS-3-PSS_MAX_KEY_FAIL: pss set runtime max key failed due to error: [hex]. Explanation DSTATS failed to set the persistent storage service (PSS) runtime max key because of the reason shown in the error message.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message DSTATS-3-PSS_SNAPSHOT_DEBUG_FAIL: pss snapshot runtime debug to uri:[chars] failed due to error: [hex]. DSTATS failed to snapshot the persistent storage service (PSS) runtime debug to the URI because of the reason shown in the error message.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message switch. Explanation EPP-5-EPP_LOOPBACK: Interface [chars] is looped back to the same The interface is looped back to another interface on the same switch. Recommended Action Check the connectivity of this interface and ensure that it is connected to another switch. Introduced Cisco MDS SAN-OS Release 1.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message ETHPORT-5-IF_DOWN_CHANNEL_ADMIN_DOWN: Interface [chars] is down (Channel admin down). This interface belongs to a PortChannel and the PortChannel is configured to be administratively down.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message ETHPORT-5-IF_DOWN_DOMAIN_MAX_RETRANSMISSION_FAILURE: Interface [chars] is down (Isolation due to domain manager other side not responding). Explanation Remote end domain manager is not responding. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.2(2a).
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message disabled). Explanation ETHPORT-5-IF_DOWN_ERROR_DISABLED: Interface [chars] is down (Error The interface encountered an error during configuration. Collect more information about failed interface using show port internal all interface [char].
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message ETHPORT-5-IF_DOWN_FCOT_VENDOR_NOT_SUPPORTED: Interface [chars] is down (Error disabled - Fcot vendor not supported). Explanation The inserted small form-factor pluggable (SFP) device is not supported. Recommended Action Contact customer support for a list of authorized SFP vendors.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message ETHPORT-5-IF_DOWN_INCOMPATIBLE_ADMIN_SPEED: Interface [chars] is down (Error disabled - Incompatible admin port speed). Explanation The configured speed is not supported on this interface. Recommended Action Enter show port internal info to determine the range of speed supported on this interface.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message ETHPORT-5-IF_DOWN_LOOPBACK_ISOLATION: Interface [chars] is down (Isolation due to port loopback to same switch). Explanation The interface is looped back to another interface on the same switch. Recommended Action Check the connectivity of this interface and ensure that it is connected to another switch.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message ETHPORT-5-IF_DOWN_PEER_CLOSE: Interface [chars] is down(TCP conn. closed by peer). Explanation The FCIP peer connected to this interface closed the TCP connection. Enter show interface to find the IP address of this FCIP interface. Check to see why the peer closed the TCP connection.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message ETHPORT-5-IF_DOWN_SOFTWARE_FAILURE: Interface [chars] is down (Port software failure). Explanation The software servicing the data path on the port has failed. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.2(2a).
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message ETHPORT-5-IF_DOWN_SUSPENDED_BY_MODE: Interface [chars] is down (Suspended due to incompatible mode). This interface belongs to a PortChannel and the operational mode of the interface is different from that of the PortChannel.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message ETHPORT-5-IF_DOWN_TCP_MAX_RETRANSMIT: Interface [chars] is down(TCP conn. closed - retransmit failure). Explanation Interface is down due to a maximum retransmission failure. Recommended Action This may be due to loss of IP connectivity.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message ETHPORT-5-IF_DOWN_ZONE_REMOTE_NO_RESP_ISOLATION: Interface [chars] is down (Isolation due to remote zone server not responding). Explanation Isolated due to remote zone server not responding. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release1.2(2a). Error Message ([chars]).
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m FC-TUNNEL Messages This section contains the FC-TUNNEL messages. FC-TUNNEL-3 Error Message FC-TUNNEL-3-INTERNAL_ERROR: Internal error: [chars]. FC MPLS tunnel process encountered a general error, one that does not fall in any of the categories. [chars] describes the error and its context.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Introduced Cisco MDS SAN-OS Release 1.2(2a). Error Message FC-TUNNEL-3-PSS_CFG_RESTORE_ERROR: Configuration restoration for [chars] failed with error [hex]. FC MPLS tunnel read the saved configuration and encountered an error while rebuilding the runtime configuration.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message FC-TUNNEL-3-UNEXPECTED_MTS_MSG: Unexpected MTS message, opcode [dec], is received. FC MPLS tunnel process received unexpected messaging and transaction service (MTS) event. The error message shows the messaging and transaction service (MTS) opcode. Explanation Recommended Action No action is required.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m FCC-5 Error Message FCC-5-BAD_MSG: Received bad message: [chars]. Explanation The Fibre Channel Congestion Control process has received a malformed or unrecognized message. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.2(2a).
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Introduced Cisco MDS SAN-OS Release 1.3(4a). Error Message FCC-5-STARTING: FCC process started. Explanation The Fibre Channel Congestion Control process started successfully. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.2(2a).
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Introduced Cisco MDS SAN-OS Release 2.0(1b). Error Message FCC_LC-2-UNABLE_READ_DATA: Unable to read fcc data ([chars]). Explanation Fibre Channel Congestion Control is unable to read and process relevant FCC data. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 3.0(1).
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m FCC_LC-6 Error Message FCC_LC-6-PRIO_UPDATE: Updated enable priority to [dec]. Explanation The Fibre Channel Congestion Control line card process is active for packets with priority less than or equal to the threshold shown in the error message. Recommended Action No action is required.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m FCDD-SLOT#-4 Error Message Explanation FCDD-SLOT#-4-LOG_FCDD_WARNING: Warning!: [chars]. Serious errors that affect all normal operations occurred. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.2(2a). FCDD-SLOT#-5 Error Message Explanation FCDD-SLOT#-5-LOG_FCDD_GCONF_FSM: [chars].
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message Explanation FCDD-SLOT#-5-LOG_FCDD_VNO_FSM: [chars]. Illegal event received in VSAN normal operation finite state machine (FSM). Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.2(2a). FCDD-SLOT#-7 Error Message Explanation FCDD-SLOT#-7-LOG_FCDD_DEBUG: [chars].
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m FCDD_HELPER-SLOT#-5 Error Message Explanation FCDD_HELPER-SLOT#-5-LOG_FCDDH_DEBUG: Unexpected error: [chars]. Unexpected errors that affect some normal operations occurred. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.2(2a). Deprecated Cisco MDS SAN-OS Release 1.3(1).
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m FCDDH-SLOT#-5 Error Message Explanation FCDDH-SLOT#-5-LOG_FCDDH_DEBUG: Unexpected error: [chars]. Unexpected errors that affect some normal operations occurred. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.3(1). Error Message Explanation FCDDH-SLOT#-5-LOG_FCDDH_NOTICE: [chars].
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message [chars]). FCDOMAIN-2-EPORT_ISOLATED: Isolation of interface [chars] (reason: Explanation The domain manager has isolated the interface because of the reason shown in the error message. Enter show interface.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message FCDOMAIN-2-INITIALIZATION_FAILED: Initialization sequence failed. The domain manager has not been able to complete the initialization sequence. The domain manager depends on resources not available at the moment.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message FCDOMAIN-2-NON_VIRTUAL_DOMS_CONFLICTS: During VSAN merge detected conflict between two switches having the same non-virtual domain ID [dec] and the same WWN [chars]. Explanation Two switches have the same non-virtual domain ID and the same WWN.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message Explanation FCDOMAIN-2-SYSBIND_FAILED: Bind to System Manager service failed. The domain manager has not been able to contact the system manager. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.2(2a).
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Introduced Cisco MDS SAN-OS Release 3.0(1). Error Message failed). FCDOMAIN-3-MTSOPENTRX_FAILED: IPC failure (opening of a transaction Explanation The domain manager was not able to open a transaction for high availability purposes. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.2(2a).
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message Explanation FCDOMAIN-3-NVRAMFAILURE: NVRAM open failed. Reading the last assigned run time domain IDs from NVRAM failed. Recommended Action The domain manager is able to continue without using the NVRAM. Introduced Cisco MDS SAN-OS Release 1.2(2a).
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m FCDOMAIN-4 Error Message FCDOMAIN-4-DM_ALLOWED_DM_LIST_MOD_ON_SUBORDINATE: Allowed domain list for vsan [dec] modified on subordinate switch with fcdomain distribution enabled. Explanation The allowed domai list was modified on a non-principal switch while fcdomain distribution was enabled.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m FCDOMAIN-5 Error Message FCDOMAIN-5-DOMAIN_TYPE_IS_PREFERRED: The domain ID type is currently configured as preferred in all the existing VSANs. All the currently existing VSANs have the domain ID type configured as preferred.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Introduced Cisco MDS SAN-OS Release 1.2(2a). Deprecated Cisco MDS SAN-OS Release 1.3(4a). Error Message FCDOMAIN-5-UNKNOWNDOMAININCFSDATAREQUEST: Received CFS Data request from unknown domain [dec]. Explanation A CFS Data request from the unknown domain [dec] has been received. Recommended Action No action is required.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message FCDOMAIN-6-CANNOTFREESINGLEFCID: Impossible to free single FCIDs. Explanation It is not possible to free single FC IDs. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.2(2a). Error Message FCDOMAIN-6-CLEARLOCKNOTIFICATIONRECEIVED: Implict lock release.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message FCDOMAIN-6-EPORT_ALREADY_CREATED: Interface [chars] already created. Explanation The interface is already created. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.2(2a). Error Message FCDOMAIN-6-EPORT_ALREADY_DOWN: Interface [chars] is already down.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message Explanation FCDOMAIN-6-FABRICNAME_INVALID: Fabric name not available. Fabric name is not available. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.2(2a). Error Message Explanation FCDOMAIN-6-FABRICNAME_VALID: Fabric name [chars] available. Fabric name is available.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message FCDOMAIN-6-FCIDP_ENABLED_DOM_TYPE_PREFERRED: FCID persistency is enabled, but the domain ID type is configured as preferred. The FC ID persistency feature is enabled, but the domain ID type is configured as preferred.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message FCDOMAIN-6-INVALIDARG: Requested FCID of type 00.00.YY, but specifying an entire area. Explanation An FC ID was requested with type 00.00.YY, but specified an entire area. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.2(2a).
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message FCDOMAIN-6-NON_VIRTUAL_DOMS_CONFLICTS: During VSAN merge detected conflict between two switches having the same non-virtual domain ID [dec] and the same WWN [chars]. Explanation It has been detected that two switches have the same non-virtual domain ID [dec] and the same WWN [chars].
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message FCDOMAIN-6-REQSINGLEFCIDWITHINRESERVEDRANGE: Requested single FCIDs in area [dec] within the reserved range. Explanation Requested single FC IDs in an area within the reserved range. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.2(2a).
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message FCDOMAIN-6-VIRTUAL_IVR_DOMS_OVERLAPPING: During VSAN merge detected overlap with local virtual IVR domain ID [dec]. Explanation The VSAN merge detected an overlap between the IVR virtual domain ID on the local VSAN and the domain IDs on the remote VSAN. Recommended Action No action is required.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Introduced Cisco MDS SAN-OS Release 1.2(2a).
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message FCDOMAIN-7-FC2_RETRY: Retransmission of FC2 frame on interface [chars] (Cmd Code: [hex]). The domain manager is retrying an FC2 frame on the interface because of a loss/no response. The command code of the frame is shown in the error message. Explanation Recommended Action No action is required.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message FCDOMAIN-7-PREACTIONTYPE_UNKNOWN: fcdomain state machine has hit an unknown pre-action type. Explanation An undefined pre-action type has been used. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.2(2a).
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m FCFWD-4 Error Message Explanation FCFWD-4-WARNING: [chars]. FCFWD is generating a relevant notification. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.2(2a). FCFWD-6 Error Message Explanation FCFWD-6-INFO: [chars]. An FCFWD event happened. Recommended Action No action is required.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m FCMPLS-3 Error Message FCMPLS-3-INTERNAL_ERR: Internal err: [chars]. FC MPLS process encountered a general error, one that does not fall in any of the categories. The error message describes the error and its context. Explanation Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.2(2a).
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m FCMPLS-5 Error Message FCMPLS-5-LDP_SES_ESTABLISHED: LDP session with [chars] is established. Explanation A new LDP session is established. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.2(2a). Deprecated Cisco MDS SAN-OS Release 1.3(1).
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message FCMPLS-6-UNKNOWN_MSG_TYPE_RXED: Unknown LDP message type 0x[hex] is received from [chars]. LDP process received an unknown LDP message type is specified in hex.The error message describes the LDP peer. Explanation Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.2(2a).
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message FCNS-2-NO_RESPONSE: domain [dec]. Explanation No response in the VSAN from domain shown in the error message. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.2(2a). Error Message Explanation FCNS-2-PSS_VERSION_MISMATCH: : for [chars].
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message Explanation FCNS-3-DB_FAILURE: : [chars]. A failure occurred in the Fibre Channel name server database. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.2(2a). Error Message FCNS-3-MALLOC_FAILURE: : [chars]. Explanation Memory allocation failed.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m FCS Messages This section contains the Fabric Configuration Server (FCS) messages. FCS-2 Error Message Explanation FCS-2-ALLOC_FAILED: Memory allocation failed for size:[dec]. Memory allocation failed. Recommended Action Restart the process. Introduced Cisco MDS SAN-OS Release 1.2(2a). Error Message chunk.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m FCS-3 Error Message FCS-2-PSS_VER_FAIL: PSS file [chars] has version [dec].[dec].[dec], expected version [dec].[dec].[dec]. There was a mismatch in the persistent storage services (PSS) version.The error message indicates the PSS service, its current version number, and the expected version.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message FCS-3-NO_MTS_RESP: [chars]. Explanation There was no response to a messaging and transaction service (MTS) request. The error message indicates details of the messaging and transaction service (MTS) message. If you purchased Cisco support through a Cisco reseller, contact the reseller directly.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m FCS-4 Error Message FCS-4-BAD_CT_FRAME: Invalid FCS frame: [chars] received from [hex]. Explanation An invalid FCS FC-CT frame with [chars] received from FC-ID [hex]. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 3.2(1). FCS-5 Error Message FCS-5-API_FAIL: [chars]: [chars].
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m FCSP-MGR-2 Error Message FCSP-MGR-2-ASSERT_FAILED: Code path reached unexpected location: assert might have been activated: File [chars] Line [dec]. Explanation This is a deprecated message and should be ignored. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.2(2a).
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message FCSP-MGR-2-FCSP_AUTHENT_FAILURE: FC-SP Authentication failure on Port [chars] (FC-SP Failure Reason: [chars] [chars]). Fibre Channel authentication failed on the port.The error message shows the reason Explanation code detail.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Introduced Cisco MDS SAN-OS Release 1.2(2a). Error Message FCSP-MGR-2-PSS_INIT_FAILED: PSS Infrastructure Initialization failed ( [chars] ). Explanation The persistent storage services (PSS) infrastructure initialization failed. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.3(1).
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m FDMI-2 Error Message FDMI-2-MTS_ERROR: MTS message transmission failed with error [dec]. Explanation The Fabric-Device Management Interface (FDMI) process unsuccessfully tried to send a messaging and transaction service (MTS) message. MTS error number is specified in the error message.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message FDMI-3-INTERNAL_ERROR: Internal err: [chars]. Explanation The Fabric-Device Management Interface (FDMI) process encountered a general error, one that does not fall in any of the categories. The error message describes the error and its context. Recommended Action No action is required.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message FDMI-3-SW_REJ_RESPONSE: Reject response [chars] from switch whose domain id is [dec]. Explanation The Fabric-Device Management Interface (FDMI) process sent an inter-switch packet to a switch and has received the reject response with reason code in the error message. Recommended Action No action is required.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m FEATURE-MGR-2 Error Message Explanation FEATURE-MGR-2-MODULE_FM_DONE: feature manager completed. Feature manager completed. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.3(1). Error Message Explanation FEATURE-MGR-2-MODULE_FM_STARTED: feature manager started. Feature manager started.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m FICON-3 Error Message FICON-3-E_ASSIGN_BINDING_PN_FAIL: [chars]. Explanation Port number has FCIP or port channel binding that cannot be removed or changed. Recommended Action Remove port number binding of the logical interface first. Introduced Cisco MDS SAN-OS Release 3.0(1).
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message FICON-3-E_INVALID_PA_BRINGUP_FAIL: [chars]. Explanation This port either has an invalid port address assigned or has no port address assigned. Recommended Action Assign a valid FICON port number to the port. Introduced Cisco MDS SAN-OS Release 3.0(1).
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m FICON-6 Error Message FICON-6-PDCM_CHANGE: VSAN [dec] port-address [dec] prohibit mask set to [chars]. The FICON prohibit dynamic connectivity mask (PDCM) for this port has changed. The VSAN port address PDCM is now set to the value shown in the error message. Explanation Recommended Action No action is required.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Introduced Cisco MDS SAN-OS Release 1.3(4a). Error Message FLOGI-5-MSG_PORT_LOGGED_IN: [VSAN [dec], Interface [chars]] Nx Port [chars] with fcid [chars] logged IN. Explanation Nx port logged in with the specified information. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.2(2a).
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m FSPF-3 Error Message FSPF-3-BAD_FC2_PKT: Received bad FC2 packet on interface [chars] VSAN [dec] : [chars]. Explanation Fabric Shortest Path First (FSPF) received a bad FC2 packet on the interface and VSAN shown in the error message. The error description is shown in the error message.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message FSPF-3-HELLO_MISMATCH: Mismatch in [chars] in the Hello packet on interface [chars] in VSAN [dec]. Explanation There is a mismatch in the entry in the hello packet received on the interface and VSAN shown in the error message. The packet will be dropped.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message FSPF-3-RIB_ERR: Error in RIB : [chars]. Explanation Fabric Shortest Path First (FSPF) had an error in interacting with the routing information base (RIB). The error description is shown in the error message. Recommended Action Enter show processes to check if RIB application is running.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m FSPF-4 Error Message FSPF-4-FC2_DOWN_INTF: Received FC2 packet on DOWN interface [chars] in VSAN [dec]. Explanation Fabric Shortest Path First (FSPF) received a FC2 packet on inactive interface in the VSAN shown in the error message.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message FSPF-4-LSR_MIN_LS_ARRIVAL: Packet arrived before MIN_LS_ARRIVAL, Dropping LSR [dec] on interface [chars] in VSAN [dec]. An LSR packet is dropped as it arrived before MIN_LS_ARRIVAL.LSR belonged to the domain shown in the error message and was received on the interface and VSAN shown in the error message.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message Explanation FSPF-6-DELETE_LSR: LSR deleted for domain [dec] in VSAN [dec]. The LSR for the domain is deleted from the database for VSAN shown in the error message. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.2(2a).
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message FSPF-6-SELF_ORIGINATED: Received local LSR in VSAN [dec] with higher incarnation number. An LSR for the local domain was received in the VSAN shown in the error message with an incarnation number higher than the one in the database. This situation should only occur initially on a topology change.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m IKE Messages This section contains the Internet Key Exchange (IKE) messages. IKE-3 Error Message IKE-3-CRYPTO_INIT_ERROR: Explanation IKEv2 crypto init error: [chars]. Cryptographic initialization error. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 2.0(1b).
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message IKE-3-PHASE1_PROPOSAL_MISMATCH: found for peer [chars]. Explanation IKEv1: No matching phase 1 proposal There is an Internet Key Exchange (IKE) policy mismatch for the peer. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 2.0(1b).
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Introduced Cisco MDS SAN-OS Release 2.0(1b). Error Message [chars]. IKE-4-MESSAGE_ERROR: IKEv2 message (from [chars]) message error: Explanation Internet Key Exchange (IKE) received a malformed message that does not adhere to the IKE protocol. Recommended Action No action is required.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m ILC_HELPER Messages This section contains the intelligent line card helper messages. ILC_HELPER-2 Error Message ILC_HELPER-2-NO_LICENSE_REBOOT: Linecard [dec] will reboot now. Explanation The SSE license has expired; therefore, the line card will be rebooted.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m ILC-SPAN-3 Error Message ILC-SPAN-3-ERROR: [chars]. Explanation The intelligent line card SPAN manager encountered an error. If you purchased Cisco support through a Cisco reseller, contact the reseller directly. If you purchased support directly from Cisco Systems, contact Cisco Technical Support.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message IMAGE_DNLD-SLOT#-2-ADDON_IMG_DNLD_SUCCESSFUL: Module image download process. [chars]. Explanation The add-on image download and install successful. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.2(2a). Deprecated Cisco MDS SAN-OS Release 1.3(4a). Error Message [chars].
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message IMAGE_DNLD-SLOT#-2-IMG_DNLD_STARTED: Module image download process. [chars]. The image download started. The module image downloads are nondisruptive to module operation. Explanation Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.2(2a).
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m IMAGE_UPGRADE Messages This section contains the image upgrade (IMAGE_UPGRADE) messages. IMAGE_UPGRADE-SLOT#-2 Error Message Explanation IMAGE_UPGRADE-SLOT#-2-IMAGE_UPGRADE_ERROR: [chars]. An image upgrade error has occurred. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.2(2a).
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m IPACL-1 Error Message Explanation IPACL-1-ALERT: [chars]. The IP access control list caused failures in other services. If you purchased Cisco support through a Cisco reseller, contact the reseller directly. If you purchased support directly from Cisco Systems, contact Cisco Technical Support.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m IPACL-5 Error Message Explanation IPACL-5-NOTE: [chars]. The IP access control list does not support this operation. Recommended Action Enter debug ipacl all, then recreate the operation scenario to find out more details. Introduced Cisco MDS SAN-OS Release 1.2(2a). IPACL-6 Error Message IPACL-6-INFO: [chars].
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message IPCONF-3-INIT_FAILED: Initialization failed. Component [chars]. Explanation The service failed to start. The failure is initializing the component shown in the error message. Recommended Action Enter show process to check the status of the other processes. Debug the specified component.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message Explanation IPCONF-6-ROUTE_NOT_ACTIVE: The [chars] is not active. The specified route is successfully configured but currently is not active. Recommended Action Check that the route is correct and the outgoing interface is operationally up. Introduced Cisco MDS SAN-OS Release 1.2(2a).
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message Explanation IPFC-3-IOCTL_FAILED: IOCTL failed. An IOCTL to the character device failed. Enter show ipfc internal interface vsan for all the configured VSAN interfaces to check the internal status, and enter the show ipfc internal mip CLI command to check the internal status.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m IPS Messages This section contains the IP service (IPS) messages. IPS-2 Error Message IPS-2-ISCSI_IPS_INIT: Ips initialization of [chars] [chars]. Explanation The IP service (IPS) initialization failed. If you purchased Cisco support through a Cisco reseller, contact the reseller directly.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message IPS-3-FCIP_FTA_ERA_35: ERA [hex] presented to CH FCID: [hex] CHI: [hex] from FCIP CU FCID [hex] CUI: [hex] DA [hex] VSAN: [hex]. Explanation FCIP got an ERA 35. Recommended Action If you purchased Cisco support through a Cisco reseller, contact the reseller directly.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message IPS-3-IPS_FIPS_TEST_FAILED: IPS FIPS compliance test failed. Explanation IPS FIPS compliance test failed. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 3.1(1). Error Message IPS-3-IPS_HIFN_CRYPTO_ENGINE_POST_FAILED: Crypto engine in the IPS module [dec] has failed POST tests.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message IPS-3-ISLB_CFS_CONFIG_FAILED: [chars]; [chars]. Explanation An error occurred while distributing the CFS config data. The reason for the failure is listed in the message. Recommended Action If you purchased Cisco support through a Cisco reseller, contact the reseller directly.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message IPS-3-ISLB_CFS_MERGE_CONFIG_FAILED: [chars]; [chars]. An error occurred while distributing the CFS merge config data. The reason for the failure is listed in the message. Explanation Recommended Action If you purchased Cisco support through a Cisco reseller, contact the reseller directly.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message IPS-3-ISLB_CFS_MERGING_CONFIG_DB_FAILED: [chars]; [chars]. Explanation An error occurred while merging the config data. The reason for the failure is listed in the message. Recommended Action If you purchased Cisco support through a Cisco reseller, contact the reseller directly.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message IPS-3-ISLB_ZONE_ACTIVATION_FAILED: iSLB zoneset activation returned [hex] for VSAN [dec]. Explanation iSLB zone set activation failed. Recommended Action If you purchased Cisco support through a Cisco reseller, contact the reseller directly.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message IPS-4-FCIP_LICENSE_BIND_FAILED: Bind failed for [chars] due to [chars] for license failure; configuration accepted but bind failed. Explanation The FCIP configuration was accepted but the FCIP interface did not bind to a physical interface because the appropriate license was not available.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Introduced Cisco MDS SAN-OS Release 3.0(1). Error Message IPS-5-FCIP_FTA_DISBAND_GRP_CMD: Disband Group message processed PGID: [chars] CH FCID: [hex] CHI: [hex] CU FCID [hex] CUI: [hex] DA [hex] VSAN: [hex]. Explanation FCIP disbanded a group. Recommended Action No action is required.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Introduced Cisco MDS SAN-OS Release 3.0(1). Error Message IPS-5-FCIP_FTA_RESIGN_GRP_CMD: Resign group processed for PGID: [chars] CH FCID: [hex] CHI: [hex] CU FCID [hex] CUI: [hex] DA [hex] VSAN: [hex]. Explanation FCIP resigned a group. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 3.0(1).
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message IPS-5-FCIP_FTA_TURN_OFF_NONLAST_VSAN: FTA turned off for the Non-Last VSAN, [chars] VSAN: [hex]. Explanation FTA was turned off for the non-last Vsan. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 3.0(1).
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message IPS-5-FCIP_TA_CFG_MISMATCH: [chars]: Mismatch in FCIP Tape Acceleration configuration with peer. Explanation The FCIP tape acceleration configuration does not match the configuration on the peer. Recommended Action Adjust the FCIP tape acceleration configuration to be consistent with the peer.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Introduced Cisco MDS SAN-OS Release 3.0(1). Error Message IPS-5-ISCSI_CONN_DOWN_BATCH: [chars]: [dec] iSCSI sessions failed in last [chars], reason: [chars]. Explanation The listed number of iSCSI sessions were down during the last interval for the reason shown in the error message. Recommended Action No action is required.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message IPS-5-ISCSI_SESSION_REDIRECT_TIMEOUT: iSCSI Session initiator [chars] to [chars] redirected to [chars] timeout. Explanation iSCSI session redirect has timed out. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 3.0(1).
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message IPS-5-ISCSI_PORT_FAILOVER: [chars]: iSCSI Explanation The Fibre Channel session for the iSCSI session failed over to newly active port. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.3(2a).
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message IPS-5-SFRAME_FABRIC_WWN_MISMATCH: [chars]: special frame fabric wwn mismatch. A special frame was received, and the source or destination fabric WWN does not match the local destination or source fabric WWN. Explanation Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.2(2a).
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Introduced Cisco MDS SAN-OS Release 3.0(1). Error Message IPS-5-SFRAME_RESP_NOT_RECV: [chars]: special frame response was not received by active-side FCIP. Special frame response was not received by the active-side of the FCIP TCP tunnel within given time period. Explanation Recommended Action No action is required.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Introduced Cisco MDS SAN-OS Release 1.3(1). IPS_SB_MGR Messages This section contains the IP Storage services sibyte manager (IPS_SB_MGR) messages. IPS_SB_MGR-SLOT#-2 Error Message IPS_SB_MGR-SLOT#-2-NODE_CORE_NOT_RESPONDING: [Node [dec], Core [dec]]: Not responding to heartbeats, state=[hex].
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message IPS_SB_MGR-SLOT#-2-SB0_REIMAGE_PREPARE_FAIL:Sibyte0 reimage disk formatting failed. Explanation There was a problem during the partitioning of the disk and the creation of file systems during reimage. Recommended Action If you purchased Cisco support through a Cisco reseller, contact the reseller directly.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message IPS_SB_MGR-SLOT#-2-SIBYTE_NOT_RESPONDING:Sibyte is not responding to heartbeats. The code of either core-0 or core-1 is not incrementing heartbeats periodically or heartbeat responses from sibyte are not making through to the sibyte manager.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message IPS_SB_MGR-SLOT#-4-NODE_NOT_COMPAT_WITH_CURRENT: svc-node[dec] image is not compatible with current node image. Explanation The new SAN Volume Controller (SVC) image is not compatible with the SVC image currently running on the node.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Deprecated Cisco MDS SAN-OS Release 1.3(2a). Error Message IPS_SB_MGR-SLOT#-4-SB1_NOT_COMPAT_WITH_ADD_ON:Sibyte1 is not compatible with add on. Explanation The code of sibyte1 is not compatible with the add on image running on the line card.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message IPS_SB_MGR-SLOT#-6-SBMGR_SDWRAP:Sbmgr sdwrap: [chars]. Explanation This is for messages from the sibyte manager on the line card to the supervisor system messages log. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.3(1). Deprecated Cisco MDS SAN-OS Release 1.3(2a).
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m IPsec-3 Error Message IPSEC-3-14_2_MODULE_PACKETS_DROPPED: [chars]: packets were dropped in the module. Explanation The 14/2-port Multiprotocol Services (14/2-MPS) module dropped packets.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message IPSEC-5-IPSEC_DISABLED_LIC_EXPIRED: IPSec Disabled due to License Expiry. Explanation IPsec is disabled because the license expired. Recommended Action Install an updated, valid license to continue using this feature. Introduced Cisco MDS SAN-OS Release 2.1(1a).
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m IPsec-7 Error Message IPSEC-7-IPSEC_SA_CREATED: [chars]: IPSec SA created: local_ip: [chars], peer_ip: [chars], [chars] SPI: [dec] ([hex]). Explanation An IPsec security association (SA) was created. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 2.0(1b).
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Introduced Cisco MDS SAN-OS Release 1.2(2a). Error Message ISAPI-SLOT#-0-INVISTA_EMERG: [chars]. Explanation Isapi-invista software messages. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 3.2(1). Error Message ISAPI-SLOT#-0-NSP_EMERG: [chars]. Explanation Isapi-nsp software messages.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message ISAPI-SLOT#-1-NSP_ALERT: [chars]. Explanation Isapi-nsp software messages. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 3.2(1). Error Message ISAPI-SLOT#-1-SSM_ALERT: [chars]. Explanation This is an intelligent switch API alert software message.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message ISAPI-SLOT#-2-SSM_CRIT: [chars]. Explanation This is an intelligent switch API critical software message. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 2.1(1a). Error Message ISAPI-SLOT#-2-SSM_CRIT: [chars]. Explanation Isapi software messages.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message ISAPI-SLOT#-3-SSM_ERROR: [chars]. Explanation This is an intelligent switch API error software message. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 2.1(1a). ISAPI-SLOT#-4 Error Message ISAPI-SLOT#-4-ILC_WARN: [chars].
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m ISAPI-SLOT#-5 Error Message ISAPI-SLOT#-5-ILC_NOTICE: [chars]. Explanation This is an intelligent switch API notice software message. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.2(2a). Error Message ISAPI-SLOT#-5-INVISTA_NOTICE: [chars]. Explanation Isapi-invista software messages.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message ISAPI-SLOT#-6-INVISTA_INFO: [chars]. Explanation Isapi-invista software messages. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 3.2(1). Error Message ISAPI-SLOT#-6-NSP_INFO: [chars]. Explanation Isapi-nsp software messages. Recommended Action No action is required.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message ISAPI-SLOT#-7-SSM_DEBUG: [chars]. Explanation This is an intelligent switch API debug software message. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 2.1(1a). ISNS Messages This section contains the Internet Storage Name Service (ISNS) messages.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m of sync. with this peer. We recommend that you discard this CFS session using ivr abort command and then re-enter the configuration changes. You can alternatively use Fabric Manager and/or Device Manager instead of the command line method. Recommended Action No action is required.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message IVR-2-DEVICE_VSAN_REWRITE_FAILURE: Failure while programming VSAN rewrite entries for pWWN [chars] on incoming VSAN [dec]. Device may not be able to communicate with its peer devices. Explanation Device failed to program the VSAN rewrite entries, probably because the hardware ran out of VSAN rewrite entries.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message IVR-2-INTEROP_MODE_2_OR_3_RDI_FAILED: VSAN [dec], requested domain [chars], received domain [chars] sWWN [chars]. Return Code [chars]. Request domain identifier (RDI) failed to allocate virtual domain in the VSAN. Received another domain instead, as shown in the error message.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message seconds. IVR-2-NO_LICENSE_WARNING: Inter-VSAN Routing would shutdown in [dec] License required for continued IVR operation is not available. Unless the required license is installed, IVR will shut down in the number of seconds shown in the error message. IVR configurations will be lost.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m IVR-3 Error Message IVR-3-ACL_ERROR: ACL API, [chars], failed with error [hex]. Explanation IVR invoked the ACL API and received an error code. The error message describes the API and the error. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.3(1).
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message IVR-3-CLEAR_FAILED: [chars]. Explanation An error occurred while clearing the lock. The reason for the failure is shown in the error message. If you purchased Cisco support through a Cisco reseller, contact the reseller directly.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message IVR-3-DEVICE_NOT_PRESENT_IN_FB_DB_FICON: Device with port WWN [chars] could not be exported to VSANs [chars] because its native switch is not present in the current active fabric binding database of those VSANs.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message IVR-3-DOMAIN_DISALLOWED_IN_INTEROP: Device with port WWN [chars] and FCID [chars] may not be able to participate in Inter-VSAN zone since domain [dec] is disallowed in the interop mode for VSAN [dec]. VSAN interop modes place restrictions on what domain ranges are allowed.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message IVR-3-QOS_IOD_UNDROP_REQUEST_TO_ACL_FAILED: qos iod undrop request vsan [dec] did [chars] failed:[chars]. This happens either after IVR retried the request few times or ACL experienced error while processing the request. Explanation Recommended Action No action is required.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message IVR-3-MERGE_FAILED: [chars]. Explanation An error occurred while merging the configuration. The reason for the failure is shown in the error message. If you purchased Cisco support through a Cisco reseller, contact the reseller directly.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message IVR-3-PSS_RTDB_RESTORE_ERROR: Runtime database restoration for [chars] failed with error [hex]. IVR read the saved runtime database and encountered an error while rebuilding the runtime database. The error message describes the runtime database that the process tried to restore and shows the system error code.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message IVR-3-UNLOCK_FAILED: [chars]. An error occurred while releasing the lock. The reason for the failure is shown in the error message. Explanation If you purchased Cisco support through a Cisco reseller, contact the reseller directly.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m IVR-4 Error Message IVR-4-AUTO_TOPOLOGY_UPDATE_DISCARDED: [chars]. Explanation The auto-topology update is discarded because of conflicts. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 2.1(1a).
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message IVR-4-ROUTE_REQUEST_TO_ACL_FAILED_AND_RETRYING: route [chars] request vsan [dec] domain [dec] failed:[chars]. Retrying the request again. Explanation This happens when either line cards are being upgraded or the ACL experienced an error while processing the request. Recommended Action No action is required.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message IVR-5-IVZS_ACTIVATION_RETRYING: Inter-VSAN zoneset activation failed with error [hex] in VSAN [dec]. retrying after [dec] seconds. Inter-VSAN zone set activation failed with VSAN shown in the error message. This could be an intermittent regular zone set activation error.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message IVR-5-IVZ_CLEANUP_DONE_BY_TIMER: Inter-VSAN clean-up is not done after waiting for 5 minutes. Explanation Inter-VSAN related configuration might not be cleaned up before the IVR process is terminated. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.3(2a).
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Introduced Cisco MDS SAN-OS Release 2.0(1b). Error Message IVR-5-SERVICE_GROUP_ACTIVATED: Inter-VSAN Service Group has been activated. Explanation Inter-VSAN Service Group has been activated. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 3.1(1).
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message IVR-6-DRAV_CRITICAL_RETRY_EXCEED: [chars]. An attempt is being made to resend the DRAV FSM frames. The details are shown in Explanation the message. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 2.1(1a).
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m IVR-7 Error Message IVR-7-CFS_REQ_RCVD: [chars]. CFS request is received. The WWN of the switch that originated this request and the rr-token of the request are provided in the message. Explanation Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 3.0(1).
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m LC-SPAN Messages This section contains the line card switched port analyzer (LC-SPAN) messages. LC-SPAN-3 Error Message Explanation LC-SPAN-3-ERROR: [chars]. The line card switched port analyzer (LC-SPAN) manager encountered an error.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m LC_PORT_CHANNEL Messages This section contains the line card PortChannel (LC_PORT_CHANNEL) messages. LC_PORT_CHANNEL-SLOT#-0 Error Message LC_PORT_CHANNEL-SLOT#-0-HW_FAILURE: fatal error in configuring [chars]: [chars]. Explanation Fatal hardware error in the PortChannel configuration. Recommended Action Reset the module.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m LC_PORT_MGR Messages This section contains the line card port manager (LC_PORT_MGR) messages. LC_PORT_MGR-SLOT#-2 Error Message LC_PORT_MGR-SLOT#-2-LC_MTS_ERROR: An MTS error has occurred in ([chars]) with the following conditions: opc=[dec] ssap=[hex] dsap=[hex] syserr=[hex].
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message LC_RDL-3-SYSLOG_EXIT: : [chars]. Explanation The line card remote domain lookup (LC_RDL) exited on errors. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.3(4a). Error Message LC_RDL-3-SYSLOG_INIT_FAIL: : [chars] [chars].
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message LC_RDL-6-SYSLOG_INFO: : [chars]. Explanation The line card remote domain lookup (LC_RDL) debug logs. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.3(4a). Error Message LC_RDL-6-SYSLOG_RESP_RCVD: : [chars] [dec].
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m LICMGR-3 Error Message LICMGR-3-LOG_LICAPP_NO_LIC: Application [chars] running without [chars] license, shutdown in [dec] days. Explanation Application [chars1] has not been licensed.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message LICMGR-3-LOG_LIC_MESSAGE_ERROR: could not handle message: [chars] of type [dec] from addr [dec]:[dec]. Explanation Could not handle an interprocess communications (IPC) message, of the type shown in the error message, sent by a component running on the shown node and service access point (SAP).
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m LICMGR-6 Error Message LICMGR-6-LOG_LICAPP_EXPIRY_WARNING: license [chars] expiry in [dec] days. Application [chars] evaluation Explanation Application will exceed its evaluation time period days and will be shut down unless a permanent license for the feature is installed.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message Explanation LICMGR-6-LOG_LIC_LICENSE_CLEARED_ALL: Cleared all licenses. Cleared all license files. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.2(2a). Error Message LICMGR-6-LOG_LIC_LICENSE_EXPIRED: feature [chars].
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m MCAST Messages This section contains the multicast (MCAST) messages. MCAST-2 Error Message MCAST-2-SHUTDOWN: Process shutting down: [chars]. Explanation The multicast process is shutting down. The action depends on the situation.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m MODULE Messages This section contains the module messages. MODULE-2 Error Message MODULE-2-LCM_UPGRADE_DONE_GENERAL_FAIL: Upgrade ready message fails seq [dec]. Explanation Upgrade ready message failed. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 3.1(1).
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Introduced Cisco MDS SAN-OS Release 2.0(1b). Error Message Explanation MODULE-2-MOD_DNLD_FAIL: Image download failed for module [dec]. The module failed to download a new image from the supervisor module.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message MODULE-2-MOD_REGFAILED: Registration failed for module [dec]. Explanation The module sent the registration message notifying a failure. Recommended Action Collect module information by entering the show module internal all module CLI command or by using a similar Fabric Manager procedure.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message MODULE-2-XBAR_SOMEPORTS_FAILED: Xbar [dec] (serial: [chars]) reported failure on ports [dec]/[dec]-[dec]/[dec] ([chars]) due to [chars] in device [dec] (error [hex]). Explanation Xbar reported a failure in the runtime diagnostic because of failure in some of the ports.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message MODULE-4-XBAR_WARNING: Xbar [dec] (serial: [chars]) reported warnings on ports [dec]/[dec]-[dec]/[dec] ([chars]) due to [chars] in device [dec] (device error [hex]). Xbar reported a warning in the runtime diagnostic because of failure in some of the Explanation ports.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Deprecated Cisco MDS SAN-OS Release 2.0(1b). Error Message MODULE-5-MOD_OK: Module [dec] is online (serial: [chars]). Explanation Module named is ready to be configured and to switch traffic. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 3.0(1).
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Introduced Cisco MDS SAN-OS Release 1.2(2a). Deprecated Cisco MDS SAN-OS Release 2.0(1b). Error Message MODULE-5-MOD_STARTUP_CFG_MISMATCH: The startup configuration cannot be applied to a different module type for module [dec] (serial: [chars]). [chars] module is replacing [chars].
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m MODULE-6 Error Message MODULE-6-MOD_PURGE_CONFIG: Purging the configuration for module [dec]. Explanation Notification is sent to remove module configurations. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 3.1(1). Error Message MODULE-6-MOD_REG_OK: Registration succeeded for module [dec].
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message NASB-SLOT#-5-LOG_ERR_TPC_VT_DESTROYED: VSAN :[dec] Virtual Target : [chars] Deleted. Explanation The virtual target in the associated VSAN is being destroyed. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 2.1(1a). Error Message VSAN down.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m NPC-SLOT#-5 Error Message Explanation NPC-SLOT#-5-LOG_NPC_DEBUG: Unexpected error: [chars]. Unexpected errors occurred that affect some normal operations. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.2(2a). Error Message NPC-SLOT#-5-LOG_NPC_NVP_FSM: Illegal event received: [chars].
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Introduced Cisco MDS SAN-OS Release 3.2(1). NPV-3 Error Message NPV-3-ACL_UPDATE_FAILED Explanation ACL update request initiated by the NPV process has failed. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 3.2(1). Error Message NPV-3-F_RJT_SENT Explanation NPV Process sent a F_RJT frame.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message NPV-3-LS_RJT_RCVD: [chars]. Explanation NPV process received an LS_RJT frame. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 3.2(1). Error Message NPV-3-MALLOC_FAILED: [chars]. Explanation An assertion failed in NPV code. Recommended Action No action is required.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Introduced Cisco MDS SAN-OS Release 3.2(1). NPV-5 Following are notification-level NPV system log messages: Error Message NPV-5-ASSERTION_FAILED Explanation An assertion failed in NPV code. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 3.2(1).
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message NPV-6-FDISC_SENT Explanation NPV process sent an FDISC frame. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 3.2(1). Error Message NPV-6-FLOGI_RCVD Explanation NPV process received an FLOGI frame. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 3.2(1).
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Introduced Cisco MDS SAN-OS Release 3.2(1). Error Message NPV-6-MTS_REQ_RCVD Explanation NPV process received an MTS request. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 3.2(1). Error Message NPV-6-MTS_REQ_SENT Explanation NPV process received an MTS request.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message NPV-6-SERVER_PROXY_LOGO_SENT Explanation NPV process sent a LOGO frame to core switch. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 3.2(1). NTP Messages This section contains the Network Time Protocol (NTP) messages. NTP-2 Error Message NTP-2-NTP_SYSLOG_CRIT_ERR: : [chars].
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message NTP-3-NTP_SYSLOG_ERR: : [chars]. Explanation Network Time Protocol (NTP) syslog error. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.2(2a). Error Message NTP-3-NTP_SYSLOG_ERR_EXT: : [chars] [dec]. Explanation Network Time Protocol (NTP) syslog error exit.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m NVP Messages This section contains the virtual N port (NVP) messages. NVP-6 Error Message NVP-6-NVP_INFO: [chars]. Explanation virtual N port (NVP) daemon informational message. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 2.0(1b).
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m NVP-SLOT# Messages This section contains the virtual N port slot (NVP-SLOT#) messages. NVP-SLOT#-2 Error Message NVP-SLOT#-2-CPP_CATASTROPHIC_ERROR: ERROR: Component ([chars]) caused critical error please reboot ILC. Explanation The listed component caused a critical error. Recommended Action Restart the line card.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message Explanation PLATFORM-0-FAIL_REMOVED: Fan module removed before [dec] seconds. Fan module was removed. This could lead to temperature alarms. Recommended Action Replace the fan module immediately. Introduced Cisco MDS SAN-OS Release 1.2(2a). Error Message alarm.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message drivers. Explanation PLATFORM-0-SYS_LC_DRIVER_LOAD_FAILED: Failed to load linecard module Failed while trying to load drivers. Recommended Action Image is possibly corrupt. Load a different image. Introduced Cisco MDS SAN-OS Release 1.2(2a).
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Introduced Cisco MDS SAN-OS Release 1.2(2a). Error Message PLATFORM-0-XBAR_CARD_CLK_FAIL: Xbar card in slot:[dec] (Serial number [chars]) encountered clock failure. Explanation The xbar in the slot named encountered clock failure. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 3.0(1).
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message PLATFORM-1-MDS9124_FAN_FAIL: Less than 4 required fans operating. A fan module has failed leaving fewer than four total fans operating. This can lead to overheating and temperature alarms. Explanation The fan needs to be replaced. Use the show platform internal info CLI command to collect more information.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Introduced Cisco MDS SAN-OS Release 3.0(1). Error Message Explanation PLATFORM-2-CASA_FAN_OK: Fan module [dec] ok. Fan module indicated is ok. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 3.0(1).
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message PLATFORM-2-FANMOD_FAN_FAIL: Fan module [dec] ([chars] fan) Failed. Fan module has failed and needs to be replaced. This can lead to overheating and temperature alarms.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message PLATFORM-2-MOD_PWRIDPROMFAIL: Module [dec] failed to power up due to IDPROM read error. Explanation The module cannot be powered up because of IDPROM read error.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message [dec]. Explanation PLATFORM-2-PFM_LC_BOOT_DEV_ABSENT: No bootflash found in Module No bootflash found. Recommended Action Put bootflash in the module and try again. Introduced Cisco MDS SAN-OS Release 1.2(2a). Error Message PLATFORM-2-PFM_LC_BOOT_DEV_FAIL: Bootflash access error in Module [dec].
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message [dec]. Explanation PLATFORM-2-PFM_LC_REGISTRATION_FAIL: Could not register with Module Module registration failed. Recommended Action Replace the module. Introduced Cisco MDS SAN-OS Release 1.2(2a). Error Message PLATFORM-2-PFM_LOW_MEMORY_CONDITION: Module [dec] is running low on memory. %ld percent used.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message PLATFORM-2-PS_CAPACITY_DIFFER: Detected power supplies with differing capacity. It is recommended to have same capacity for both powersupplies otherwise it may cause service disruptions. Explanation Detected a power supply that has a different capacity than an the other power supply.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message PLATFORM-2-PS_OK: Power supply [dec] ok (Serial number [chars]). Explanation Power Supply is ok. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 3.0(1). Error Message PLATFORM-2-PS_MISMATCH: Detected power supply [chars].
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message PLATFORM-2-PS_UNSUPPORTED: Detected an unsupported power supply [dec] [chars] for CISCO MDS 9500/9200 Multilayer Switches (Serial number [chars]). Explanation This power supply is not supported for the Cisco MDS 9500 or 9200 series of switches.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message PLATFORM-3-MOD_PWRIDPROMFAIL: Module [dec] failed to power up due to idprom read error. Explanation The module cannot be powered up because of an IDPROM read error.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m PLATFORM-5 Error Message PLATFORM-5-CHASSIS_CLKMODOK: Chassis clock module [dec] ok. Explanation Clock module on chassis is functioning properly. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.2(2a). Error Message PLATFORM-5-CHASSIS_CLKSRC: Current chassis clock source is clock-[dec].
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Introduced Cisco MDS SAN-OS Release 1.2(2a). Error Message PLATFORM-5-MOD_REMOVE: Module [dec] removed (Serial No. [chars]). Explanation The module has been removed. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.2(2a).
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message Explanation PLATFORM-5-PS_FANOK: Fan in Power supply [dec] ok. Fan module in the named power supply is operating normally. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.3(1). Error Message Explanation PLATFORM-5-PS_OK: Power supply [dec] ok (Serial No. [chars]).
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message PLATFORM-5-XBAR_PWRUP: Xbar [dec] powered up (Serial number [chars]). Explanation The xbar in the slot named is powered up. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 3.0(1). Error Message PLATFORM-5-XBAR_REMOVE: Xbar [dec] removed (Serial number [chars]).
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m PLOG_SUP-4 Error Message PLOG_SUP-4-PLOG_SUP_EXIT: Persistent Logger encountered an error [dec]. Explanation Persistent Logger encountered an error. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 3.0(1). PORT Messages This section contains the port messages.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message PORT-5-IF_BRINGUP_NOT_ALLOWED_PORT_CONFIG_FAILURE: Interface [chars] is not allowed to be operational due to port config failure for reason: [chars] ([hex]). Explanation Check interface configuration.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message PORT-5-IF_DOWN_CHANNEL_ADMIN_DOWN: Interface [chars] is down (Channel admin down). This interface belongs to a PortChannel and the PortChannel is configured to be administratively down.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message PORT-5-IF_DOWN_DOMAIN_MANAGER_DISABLED: Interface [chars] is down (Isolation due to domain manager disabled). Explanation The interface is isolated because the domain manager is disabled. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.2(2a).
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message PORT-5-IF_DOWN_ELP_FAILURE_ISOLATION: Interface [chars] is down (Isolation due to ELP failure). Explanation Exchange link parameter (ELP) failed on the interface. Enter the show port internal info CLI command or use a similar Fabric Manager/Device Manager procedure to check the ELP failure reason field.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message PORT-5-IF_DOWN_ELP_FAILURE_ISOLATION_INVALID_SWITCH_NAME: Interface [chars] is down (Isolation due to ELP failure: invalid switch name). Explanation Exchange link parameter (ELP) failed on the interface because of an invalid switch name.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message PORT-5-IF_DOWN_ELP_FAILURE_ISOLATION_UNKNOWN_FLOW_CTL_CODE: Interface [chars] is down (Isolation due to ELP failure: invalid flow control code). Explanation Exchange link parameter (ELP) failed on the interface because of an invalid flow control code.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Introduced Cisco MDS SAN-OS Release 1.2(2a). Error Message PORT-5-IF_DOWN_ETH_IF_DOWN: Interface [chars] is down(Tunnel port src interface down). Explanation Ethernet link to which the FCIP interface is bound is down. Ensure that the Ethernet cable is connected and that the interface is administratively enabled.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message PORT-5-IF_DOWN_FCSP_AUTHENT_FAILURE: Interface [chars] is down (FC-SP authentication failure). Explanation The port failed Fibre Channel Security Protocol (FC-SP) authentication with its peer. Recommended Action Check the FC-SP configuration. Introduced Cisco MDS SAN-OS Release 1.3(1).
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message PORT-5-IF_DOWN_INCOMPATIBLE_ADMIN_MODE: Interface [chars] is down (Error disabled - Incompatible admin port mode). Explanation The configured mode is not supported on this interface.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message PORT-5-IF_DOWN_INTERFACE_REMOVED: Interface [chars] is down (Interface removed). Explanation Interface was removed. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.2(2a). Error Message PORT-5-IF_DOWN_INVALID_ATTACHMENT: Interface [chars] is down(Invalid attachment).
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Introduced Cisco MDS SAN-OS Release 3.0(1). Error Message PORT-5-IF_DOWN_LOOPBACK_DIAG_FAILURE: Interface [chars] is down (Diag failure). Explanation Diagnostics failed on the interface.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message PORT-5-IF_DOWN_NOS_RCVD: Interface [chars] is down (NOS received). Explanation The physical link has gone down. Recommended Action Ensure that the cable is connected and the remote end is not shut down. Introduced Cisco MDS SAN-OS Release 1.3(4a).
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message PORT-5-IF_DOWN_PEER_CLOSE: Interface [chars] is down(TCP conn. closed by peer). Explanation The FCIP peer connected to this interface closed the TCP connection. Recommended Action Enter the show interface command or use a similar Fabric Manager procedure to provide the peer IP address of this FCIP interface.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message PORT-5-IF_DOWN_PORT_CHANNEL_MEMBERS_DOWN: Interface [chars] is down (No operational members). Explanation This is a PortChannel interface and all its members are operationally down. Recommended Action Enable at least one of the PortChannel members. Introduced Cisco MDS SAN-OS Release 1.2(2a).
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message PORT-5-IF_DOWN_SRC_PORT_NOT_BOUND: Interface [chars] is down (Tunnel port src interface unbound). Explanation The FCIP link port source interface is not bound. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.2(2a).
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message PORT-5-IF_DOWN_SUSPENDED_BY_WWN: Interface [chars] is down (Suspended due to incompatible remote switch WWN). This interface belongs to a PortChannel and the remote switch WWN of the interface is different from that of the PortChannel.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message PORT-5-IF_DOWN_TOO_MANY_INVALID_FLOGIS: Interface [chars] is down(Suspended due to too many invalid flogis. Explanation The port is suspended because of receiving a large number of invalid FLOGIs.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Introduced Cisco MDS SAN-OS Release 1.2(2a). Error Message PORT-5-IF_DOWN_ZONE_REMOTE_NO_RESP_ISOLATION: Interface [chars] is down (Isolation due to remote zone server not responding). Explanation The interface was isolated because of a remote zone server not responding. Recommended Action No action is required.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message PORT-5-MODULE_BRINGUP_NOT_ALLOWED: Not allowing module [dec] to come up for reason: [chars] ([hex]). Explanation Module is not allowed to be operational due to the current system state. Recommended Action Check the global index allocation using the show port index-allocation CLI command.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m PORT-SECURITY Messages (Deprecated) This section contains the port security (PORT-SECURITY) messages. These messages were deprecated in Cisco MDS SAN-OS Release 1.3(4a). They were replaced by the “PORT_SECURITY Messages” section on page 2-263.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message PORT-SECURITY-3-BINDING_VIOLATION: [chars] in VSAN [dec]. Explanation A login occurred that violates the port security manager (PSM) binding configurations. The error message indicates the WWN of the login entity and the VSAN. Only entries in the activated database of PSM can log in.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message Explanation PORT-SECURITY-3-EFMD_MERGE_UNKNOWN_FORMAT: [chars]. Received a corrupted exchange fabric membership data (EFMD) request packet. If you purchased Cisco support through a Cisco reseller, contact the reseller directly.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message PORT-SECURITY-3-PSS_ERR: [chars]. An error occurred during a port security manager persistent storage service (PSS) operation. The error message indicates the persistent storage service (PSS) operation that caused the error.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m PORT_CHANNEL Messages This section contains the PortChannel (PORT_CHANNEL) messages. PORT_CHANNEL-1 Error Message [[chars]]. Explanation PORT_CHANNEL-1-LC_CFG_FAILURE: configuring module [dec] failed Module configuration failed. The module is automatically reset.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m PORT_CHANNEL-2 Error Message PORT_CHANNEL-2-RESET_MODULE: reset module [dec] for not responding or returning error. Explanation A module is reset for not responding or returning an error. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.2(2a).
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message PORT_CHANNEL-3-TIMEOUT: timed out after [dec] seconds [type [chars], state [chars]]. Explanation Some operation timed out. Recommended Action Execute the show port-channel consistency CLI command or use a similar Fabric Manager/Device Manager procedure to check all module connectivity and consistency.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message [chars]. Explanation PORT_CHANNEL-4-UNEXPECTED_RESPONSE: unexpected response [chars] from Received an unexpected response and discarded it. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.2(2a). PORT_CHANNEL-5 Error Message PORT_CHANNEL-5-AUTO_CREATE_FAILURE: [chars] [chars].
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message Explanation PORT_CHANNEL-5-PORT_ADDED: [chars] added to [chars]. Ports were added to a PortChannel. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.2(2a). Error Message Explanation PORT_CHANNEL-5-PORT_REMOVED: [chars] removed from [chars].
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message Explanation PORT_CHANNEL-7-GSYNC_REQ: requesting global synchronization. PortChannel manager requested a global synchronization from the active supervisor. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.2(2a).
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m PORT_SECURITY Messages This section contains the port security (PORT_SECURITY) messages. PORT_SECURITY-2 Error Message PORT_SECURITY-2-ALLOC_FAILED: Memory allocation failed for size:[dec] for [chars]. Explanation Memory allocation failed for the entity and size shown in the error message.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message PORT_SECURITY-3-DB_ERR: [chars]. An error occurred during a port security manager database operation. The error message indicates the reason for the error. Explanation If you purchased Cisco support through a Cisco reseller, contact the reseller directly.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message PORT_SECURITY-3-LEARNT_BINDING_CONFLICT: [chars] in VSAN [dec]. Explanation An already logged in device that is learned during activation is in conflict with the port security manager active binding configuration. The error message indicates the WWN of the login entity, interface, and VSAN.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message PORT_SECURITY-6-INFO: [chars]. Explanation An event happened that affects the port security manager. The error message indicates the event. Introduced Cisco MDS SAN-OS Release 1.3(4a). PROC_MGR Messages This section contains the process manager (PROC_MGR) messages.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message PROC_MGR-SLOT#-2-PROC_MGR_COMP_DEP_FAIL: ERROR: Dependency failure Component ([chars]) depends on ([chars]). Explanation Component dependency failure. Recommended Action Check whether the component exists. Introduced Cisco MDS SAN-OS Release 1.2(2a).
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message [chars]. Explanation PROC_MGR-SLOT#-2-PROC_MGR_QUIT: Process manager quitting because: Process manager is quitting. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.2(2a).
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message PROC_MGR-SLOT#-2-PROC_MGR_UT_SEM_GET_FAIL: ERROR:[chars] [dec]: Failed to get utaker semaphore: [dec]. Explanation Utaker semaphore get failed. Recommended Action Restart the line card. Introduced Cisco MDS SAN-OS Release 1.2(2a).
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m PSS Messages This section contains the persistent storage service (PSS )messages. PSS-0 Error Message Explanation PSS-0-PSS_NO_MORE_PAGES: [chars]: needs more working pages. Service needs more working page buffers. If you purchased Cisco support through a Cisco reseller, contact the reseller directly.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message PSS-0-PSS_WRITE_DATA_FAILURE: [chars]: failed to write data to [chars] block [dec]: [chars]. Explanation The persistent storage service cannot write data because of a file system or disk error. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.2(2a).
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message [chars]. PSS-1-PSS_VERSION_MISMATCH: [chars]: found version mismatch in Explanation The persistent storage service found a database whose format it cannot interpret because of a version mismatch. Recommended Action The image upgrade was not done properly.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message PSS-4-PSS_RECOVERY_ENDED: [chars]: recovered [chars] successfully. Explanation The persistent storage service recovery finished. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.2(2a).
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m QOS Messages This section contains the quality of service (QOS) messages. QOS-2 Error Message QOS-2-EXITING: Exit reason: [chars]. The QoS manager process has exited. The process has probably been restarted automatically. Explanation Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.2(2a).
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message QOS-2-STDOUT_ROTATE_FAILURE: Failed to rotate stdout file: [chars]. Explanation The QoS manager has failed to rotate its current standard output file with the file name shown in the error message. The file size could grow beyond its maximum limit. Recommended Action No action is required.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message QOS-3-GENERROR: [chars]. QoS manager encountered a general error, one that does not fall in any of the above categories. The error message describes the error and its context. Explanation Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.3(1).
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message QOS-3-UNKNOWN_MSG: Received from Node=[dec] SAP=[dec]. The QoS manager has received an unknown message from the node and sap shown in the error message.This information is for debugging only. Explanation Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.2(2a).
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message QOS-6-DISABLED_UP_MARKING: [chars]. Explanation The QoS manager has disabled marking of time-critical control traffic as high-priority traffic. Priority of such traffic is now not altered by QoS manager. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.2(2a).
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message QOS-6-MGRCREATED: QoS Manager created. Explanation QoS manager was created successfully and is up and running. This is an informational message. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.3(1).
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message Explanation QOS-6-UNKNOWNMTS: QoS Manager received an unexpected message. QoS Manager received an unexpected message. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.3(4a). RADIUS Messages This section contains the Remote Authentication Dial-In User Service (RADIUS) messages.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Introduced Cisco MDS SAN-OS Release 1.3(1). Error Message Explanation RADIUS-6-RADIUS_MESSAGE: [chars]. RADIUS message. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.3(1).
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m RDL Messages This section contains the remote domain lookup (RDL) messages. RDL-3 Error Message RDL-3-SYSLOG_ALLOC_FAIL: : [chars]. Explanation The remote domain lookup (RDL) memory allocation failed. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.2(2a).
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message RDL-3-SYSLOG_MTS_ERR: : [chars]. Explanation The remote domain lookup (RDL) messaging and transaction service (MTS) errors. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.2(2a). RDL-6 Error Message RDL-6-SYSLOG_DEBUG_1: : [chars] [hex].
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m RIB Messages This section contains the Routing Information Base (RIB) messages. RIB-0 Error Message RIB-0-EMERG: [chars]. Explanation The Routing Information Base (RIB) caused a system failure. If you purchased Cisco support through a Cisco reseller, contact the reseller directly.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message RIB-3-FIB_EXIT: fib exited. Explanation The Forwarding Information Base (FIB) had exited and may not continue operation. If you purchased Cisco support through a Cisco reseller, contact the reseller directly. If you purchased support directly from Cisco Systems, contact Cisco Technical Support.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message RIB-3-SEND_STANDBY: Cannot talk to standby rib. Lost a Routing Information Base (RIB) to Forwarding Information Base (FIB) transaction log due to an interprocess communications (IPC) failure. Explanation If you purchased Cisco support through a Cisco reseller, contact the reseller directly.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message RIB-4-WARN: [chars]. Explanation The Routing Information Base (RIB) ignored the unexpected condition. Recommended Action Enter the debug rib all command, or use a similar Fabric Manager procedure, then recreate the operation scenario to find out more details. Introduced Cisco MDS SAN-OS Release 1.2(2a).
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message RLIR-2-FC2_FAILED: RLIR FC2 operation failed: [chars]: [chars]. Explanation Registered Link Incident Record (RLIR) Fibre Channel Layer 2 (FC-2) operation failed: [chars] [chars]. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.3(1).
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m RLIR-6 Error Message RLIR-6-SYSLOG_INFO: RLIR Syslog info: [chars]. Explanation Registered Link Incident Record (RLIR) syslog info. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.3(1). Error Message RLIR-6-SYSLOG_STATUS: RLIR Syslog status: [chars]: [chars].
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m RM-SLOT#-2 Error Message RM-SLOT#-2-CPP_CATASTROPHIC_ERROR: ERROR: Component ([chars]) caused critical error SSM will be rebooted. Explanation The listed component caused a critical error. Recommended Action Restart the line card. Introduced Cisco MDS SAN-OS Release 2.1(1a).
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Introduced Cisco MDS SAN-OS Release 1.2(2a). Error Message RSCN-2-MALLOC_FAILED: RSCN Malloc failed: [chars]. Explanation The Registered State Change Notification (RSCN) memory allocation failed. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.2(2a).
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message RSCN-2-SWRSCN_REJECT: SW-RSCN rejected: [chars]: fcid [chars], Reason code-[chars], Reason code expl-[chars]. Explanation The Registered State Change Notification (RSCN) was rejected. The FC ID and reason code are shown in the error message. Recommended Action No action is required.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m SAN_EXT_TUNER-3 Error Message SAN_EXT_TUNER-3-SAN_EXT_TUNER_LICENSE_EXPIRED: SAN Extension Licence expired - Disabling SAN Extension Tuner. Explanation The SAN extension license expired or is not present. The SAN extension tuner will be disabled. Recommended Action No action is required.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message SCHEDULER-2-SCH_SYSLOG_SDWRAP_ERR: Debug infrastructure initialization failed: [chars]. Explanation Debug infrastructure failed to initialize. Recommended Action If you purchased Cisco support through a Cisco reseller, contact the reseller directly.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message SCHEDULER-3-SCH_SYSLOG_USER_ERR: Description: Failed to execute job for user id [chars] Error:[dec]. Explanation Error while attempting to execute job for user. The user maybe removed from the system. Recommended Action Ensure that the user exists. Make sure the user is not remotely authenticated.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m SCSI target Messages This section contains the SCSI target (SCSI target) messages. SCSI target-2 Error Message SCSI target-2-PROC_ADD_NPORT_FAIL: Failed to set local nport with SCSI target driver error: [hex]. SCSI target process added an N port with its peer kernel driver listed. No SCSI discovery can be performed.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message [hex]. SCSI target-2-PSS_INIT_FAIL: pss initialization failed due to error: Explanation SCSI target process persistent storage service (PSS) initialization failed due to the error listed. No SCSI discovery can be performed.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message SCSI target-3-PSS_MAX_KEY_FAIL: pss set runtime max key failed due to error: [hex]. Explanation SCSI target process persistent storage service (PSS) set runtime max key failed because of the error listed. No SCSI discovery can be performed.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message SCSI target-3-PSS_SNAPSHOT_FAIL: pss snapshot runtime to uri:[chars] failed due to error: [hex]. Explanation SCSI target process persistent storage service (PSS) snapshot of runtime to uri failed because of the error shown in the error message.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m SECURITYD Messages This section contains the security and accounting daemon (SECURITYD) messages. SECURITYD-2 Error Message SECURITYD-2-FIPS_BYPASS_SELF_TEST_STATUS: FIPS Bypass self-test status : [chars]. Explanation Status of the FIPS self-test. Recommended Action No action is required.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message SECURITYD-2-FIPS_POWERUP_SELF_TESTS_STATUS: FIPS power-up self-test status: [chars]. Explanation Status of the FIPS self-test. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 3.1(1). Error Message SECURITYD-2-FIPS_SELF_TEST_FAILED: FIPS self-test failure : [chars] : [chars].
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message Explanation SECURITYD-6-CHANGE_PASSWD: changing passwd for [chars]. Changing password for the entity listed in the error message. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.2(2a). Error Message SECURITYD-6-DELETE_STALE_USER_ACCOUNT: deleting expired user account:[chars].
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message [chars]. Explanation SENSOR-2-SNSM_SYSLOG_SHUTDOWN: Sensor Mgr process shutting down: Sensor Manager syslog message. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.2(2a). Error Message failed.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Introduced Cisco MDS SAN-OS Release 1.2(2a). Error Message SENSOR-3-SNSM_SYSLOG_BAD_MTS_MSG: Sensor Mgr Received bad MTS message: [dec]. Explanation Sensor manager syslog message. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.2(2a).
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message SENSOR_USD-2-SNSM_SYSLOG_SHUTDOWN: Sensor Mgr process shutting down: [chars]. Explanation This is an informational message indicating that the Sensor Manager is shutting down. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 3.1(1).
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message SENSOR_USD-3-SNSM_SYS_MTS_RECV_FAILURE: Sensor Mgr Error in receving MTS mesg: [dec], Error code = [dec]. Explanation This is an informational message indicating a receiving error from the messaging and transaction service (MTS). Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 3.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m SFC-3 Error Message Explanation SFC-3-ERROR: [chars]. SCSI flow client encountered the listed error. If you purchased Cisco support through a Cisco reseller, contact the reseller directly. If you purchased support directly from Cisco Systems, contact Cisco Technical Support.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m SME_CPP-2 Error Message SME_CPP-2-LOG_ERR_SME_LICENSE_EXPIRED: SME Licence expired - Disabling [chars]. Explanation Storage Media Encryption License expired or is not present. SME is disabled. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 3.2(2).
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message SME_CPP-3-LOG_ERR_SME_INTF_MISMATCH_CRYPTO_NODE_PARAMS: SME interface [chars] part of cluster [chars] with ID [chars] as a crypto node [chars], but the DPP is identified as [chars]. Explanation DPP has persistent state about a previous cluster membership on a different switch or module.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Introduced Cisco MDS SAN-OS Release 3.2(2). Error Message SME_CPP-5-SME_ENABLED: SME Enabled. Explanation SME service is enabled. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 3.2(2).
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m SKSD Message Error Message SKSD-5-SKSD_MKEY_INSTALL: smartcard(s). Explanation Installing a Master Key on the Installing a new Master Key on the smart card(s). Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 3.0(1).
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message SPAN-3-STATELESS_RESTART_ON_ACTIVE: Span is restarting as Span on active sup was restarted stateless. Because of an unrecoverable error, the switched port analyzer (SPAN) on the active supervisor was restarted stateless. The standby SPAN restarts to get in sync with the stateless SPAN on the active supervisor.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m SPAN-5 Error Message SPAN-5-ATL_VSAN_DEFAULT_ALL: Default to all VSANs for SPAN egress session. Explanation Generation 2 fabric switches support only one VSAN filter for an egress SPAN session. If a VSAN is specified, SPAN will default to use all VSANs for the egress SPAN session. Recommended Action No action is required.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message SPAN-5-STATELESS_RESTART_ON_ACTIVE: Span is restarting as Span on active sup was restarted stateless. Because of an unrecoverable error, the switched port analyzer (SPAN) on the active supervisor was restarted stateless.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m SPI_SLOT#-2 Error Message SPI-SLOT#-2-SPI_INFO: [chars] Explanation SPI Informational message. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 3.0(1). SVC Messages This section contains the SAN Volume Controller (SVC) messages. SVC-0 Error Message SVC-0-NODE_EMERG_MSG: [chars].
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message SVC-2-SVC_SYSLOG_INIT_FAILED: Initialization failed for SVC: [chars], Reason: [hex]. Explanation Initialization failed for the SAN Volume Controller (SVC). Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.3(4a).
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message [chars]. SVC-2-SVC_SYSLOG_URIFS_FAILURE: [chars] is unreachable for reason: Explanation The SAN Volume Controller (SVC) interface modflash is not accessible. Modflash is the name of the file system local to the SVC interface and is typically used for core dumps and temporary file transfers.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message SVC-3-NODE_ERR_MSG: (SVC [dec]/[dec] SS_EID_EC_ER_DUMP_RESTORE_FAILED ) Restore of hardened data failed [chars]. Explanation Restore of customer data failed. This error will be accompanied by other log entries. Recommended Action Examine the log for other error entries and follow the actions recommended.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message SVC-3-NODE_ERR_MSG: (SVC [dec]/[dec] SS_EID_IC_EV_NODE_DISENFRANCHISED ) Node missing [chars]. Explanation A node is missing from the cluster. 1. Check the status of the nodes and find the node with a status of offline. 2. Repair the failing node.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message SVC-3-NODE_ERR_MSG: (SVC [dec]/[dec] SS_EID_PL_ER_FC_ADAP_QUANTITY ) Logical Fibre Channel port missing [chars]. Explanation No active and functioning Fibre Channel port was detected by the software. Recommended Action Reload the node. If the problem persists, replace the Caching Services Module.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message SVC-3-NODE_ERR_MSG: (SVC [dec]/[dec] SS_EID_VG_ER_MED_ERRS_TOO_HIGH ) Media errors on back-end Managed Disk [chars]. Explanation Media errors on backend managed disk. 1. Repair the enclosure or disk controller. 2. Add the managed disk into the cluster. 3. Check the managed disk status.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message SVC-3-NODE_ERR_MSG: (SVC [dec]/[dec] SS_EID_VL_ER_DEVICE_RESOURCE_RAN_OUT ) Too many controllers were presented to the cluster [chars]. Explanation The configuration is not valid. Too many devices have been presented to the cluster or node. Recommended Action 1.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Introduced Cisco MDS SAN-OS Release 1.3(1). Error Message SVC-3-NODE_ERR_MSG: (SVC [dec]/[dec] SS_EID_VL_ER_IO_TIMEOUT_OVERALL ) Timeout due to excessive processing time [chars]. Explanation A managed disk has timed out. This error has been reported because a large number of disk timeout conditions have been detected.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message SVC-3-NODE_ERR_MSG: (SVC [dec]/[dec] SS_EID_VL_ER_MDISK_ACCESS_INVALID ) Access beyond end of disk, or Managed Disk missing [chars]. The error that is logged in the cluster error log indicates a software problem in the cluster, or in a disk enclosure or disk controller that is connected to the node.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message SVC-3-NODE_ERR_MSG: (SVC [dec]/[dec] SS_EID_VL_ER_MDISK_RESOURCE_RAN_OUT ) Too many Managed Disks were presented to the cluster [chars]. Explanation The configuration is not valid. Too many devices have been presented to the cluster or node. Recommended Action 1.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message SVC-3-NODE_ERR_MSG: (SVC [dec]/[dec] SS_ERR_CFG_ALL_SSH_KEYS_REMOVED ) Attempt to delete SSH keys (no effect) [chars]. Explanation The svctask rmallsshkeys command has been invoked. This command has no effect in SAN Volume Controller for Cisco MDS 9000, but is retained for compatibility.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message SVC-3-NODE_ERR_MSG: (SVC [dec]/[dec] SS_ERR_CFG_SSH_KEY_REMOVED ) Attempt to delete SSH key (no effect) [chars]. The svctask rmsshkey command has been invoked. This command has no effect in SAN Volume Controller for Cisco MDS 9000, but is retained for compatibility.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message SVC-3-NODE_ERR_MSG: (SVC [dec]/[dec] SS_NODERR_MEM_SIZE ) Memory size error [chars]. Explanation The detected memory size does not match the expected memory size for the cluster. Recommended Action A memory module on the Caching Services Module is probably faulty. Reload the node.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message SVC-3-NODE_ERR_MSG: (SVC [dec]/[dec] SS_NODERR_RESET_AND_REJECT ) Node data not found - node rejected from cluster [chars]. Explanation Node data was not found. The node has been rejected from the cluster.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m SVC-4 Error Message SVC-4-NODE_WARNING_MSG: (SVC [dec]/[dec] SS_EID_CA_EV_FIRST_DATA_PINNED ) Customer data pinned [chars]. There is pinned customer data. This warning is given when data is pinned and there were not already pinned data. Error log entries will exist for the underlying cause of the pinned data.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message SVC-4-NODE_WARNING_MSG: (SVC [dec]/[dec] SS_EID_EC_ER_DEACTIVATE_CLUSTER_IP_FAILED ) Deactivate cluster IP failed [chars]. Unable to deactivate the cluster IP for the config node. The cluster IP should be deactivated by other checks.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message SVC-4-NODE_WARNING_MSG: (SVC [dec]/[dec] SS_EID_EC_ER_FORK_FAILED ) Internal error - fork failed [chars]. Explanation The process cannot launch the I/O program. Node was rebooted because of this error. Recommended Action If this error is repeated continuously, follow these steps: 1.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message SVC-4-NODE_WARNING_MSG: (SVC [dec]/[dec] SS_EID_EC_ER_IOP_STOPPED_DUE_TO_SIGNAL ) Internal error - signal caused stop [chars]. Explanation The I/O process stopped because of a signal received. Node was warm started because of this error. 1. Ensure that the software is at the latest level on the cluster.2.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message SVC-4-NODE_WARNING_MSG: (SVC [dec]/[dec] SS_EID_EC_ER_UNKNOWN_MESSAGE_TYPE ) Internal error - message type [chars]. Node was rebooted because of an internal logic error. Explanation 1. Ensure that the software is at the latest level on the cluster. 2. Ask your customer support representative for assistance.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message SVC-4-NODE_WARNING_MSG: (SVC [dec]/[dec] SS_EID_FC_ER_PREPARE_FAILED ) FlashCopy prepare failed due to cache flush failure [chars]. Explanation A flash copy prepare task failed because a cache flush has failed. Recommended Action 1. Correct higher priority errors, and then retry the prepare tasks. 2.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message SVC-4-NODE_WARNING_MSG: (SVC [dec]/[dec] SS_EID_IC_ER_TRANSFER_FILE_FAILED ) Failed to transfer file from remote node [chars]. Explanation An attempt to retrieve a file from the dumps directory has failed. Recommended Action Determine if the remote node is still online.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message SVC-4-NODE_WARNING_MSG: (SVC [dec]/[dec] SS_EID_IC_EV_UPGRADE_PCK_DELIVERY_FAILED ) Software install package cannot be delivered to all nodes [chars]. Explanation An error occurred while sending the software package to the nodes. 1. Display the status of the nodes on the cluster. 2.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message SVC-4-NODE_WARNING_MSG: (SVC [dec]/[dec] SS_EID_VG_ER_COPIED_MEDIUM_ERROR ) I/O media error copied [chars]. Explanation During a copy or a migrate process, a media error was copied to the destination disk. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.3(1).
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message SVC-4-NODE_WARNING_MSG: (SVC [dec]/[dec] SS_EID_VL_ER_IO_MEDIUM_ERROR ) A media error has occurred during I/O to a Managed Disk [chars]. Explanation A disk I/O medium error has occurred. 1. Rewrite the bad data to the LBA block reported in the host systems SCSI sense data.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message SVC-4-NODE_WARNING_MSG: (SVC [dec]/[dec] SS_EID_VL_ER_MDISK_PORT_PREFERENCE_IGNORED ) Preferred port is not being used for Managed Disk access [chars]. Explanation The preferred port designated by the back end controller is not being used for managed disk access.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m SVC-5 Error Message Explanation SVC-5-NODE_NOTICE_MSG: [chars]. Syslog message from a SAN Volume Controller (SVC) interface node. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.3(1). Error Message SVC-5-SVC_SYSLOG_IF_CONFIG_DELETED: Interface [chars] configuration was deleted[chars].
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message SVC-6-NODE_INFO_MSG: (SVC [dec]/[dec] SS_EID_CA_EV_HWS_TO_ASYNCHRONOUS ) Pinned data reduced; cache can operate normally [chars]. Explanation Enough customer data has been unpinned that the cache is no longer required to operate in write through mode because of the pinned data.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message SVC-6-NODE_INFO_MSG: (SVC [dec]/[dec] SS_EID_FC_ER_PREPARE_COMPLETED ) Flash Copy Prepared [chars]. Explanation The flash copy mapping or consistency group has entered the prepared state. It is now possible to start or stop the mapping or group. Recommended Action No action is required.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message SVC-6-NODE_INFO_MSG: (SVC [dec]/[dec] SS_EID_RC_ER_COPY_COMP ) Remote Copy complete [chars]. Background copy complete. The standalone relationship or consistency group has transitioned from inconsistent copying to consistent synchronized. This will only be logged on the cluster of the primary virtual disk(s).
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message SVC-6-NODE_INFO_MSG: (SVC [dec]/[dec] SS_ERR_CFG_ADD_WWPN ) Port added to a Host [chars]. Explanation The svctask addhostport IBM CLI command has been invoked. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.3(1).
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message SVC-6-NODE_INFO_MSG: (SVC [dec]/[dec] SS_ERR_CFG_CLUSTER_MODIFY ) Cluster attributes modified [chars]. Explanation The svctask chcluster IBM CLI command has been invoked. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.3(1).
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message SVC-6-NODE_INFO_MSG: (SVC [dec]/[dec] SS_ERR_CFG_DELETE_MAPPING ) Virtual Disk to Host SCSI mapping deleted [chars]. Explanation The svctask rmvdiskhostmap IBM CLI command has been invoked. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.3(1).
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message SVC-6-NODE_INFO_MSG: (SVC [dec]/[dec] SS_ERR_CFG_ERRORLOG_DUMPLOG ) Error log dumped [chars]. Explanation The svctask dumperrlog IBM CLI command has been invoked. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.3(1).
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message SVC-6-NODE_INFO_MSG: (SVC [dec]/[dec] SS_ERR_CFG_FEATURISATION_CHANGED ) Licensed settings modified [chars]. Explanation The svctask chlicense IBM CLI command has been invoked. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.3(1).
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message SVC-6-NODE_INFO_MSG: (SVC [dec]/[dec] SS_ERR_CFG_HWS_SET_NAME ) IO Group name modified [chars]. Explanation The svctask chiogrp IBM CLI command has been invoked. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.3(1).
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message SVC-6-NODE_INFO_MSG: (SVC [dec]/[dec] SS_ERR_CFG_MDISK_GRP_SET_NAME ) Managed Disk Group attributes modified [chars]. Explanation The svctask chmdiskgrp IBM CLI command has been invoked. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.3(1).
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message SVC-6-NODE_INFO_MSG: (SVC [dec]/[dec] SS_ERR_CFG_NODE_CREATE_CLUSTER ) Cluster created [chars]. Explanation The cluster add IBM CLI command has been invoked. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.3(1).
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message SVC-6-NODE_INFO_MSG: (SVC [dec]/[dec] SS_ERR_CFG_NODE_UNPEND ) Node Unpend [chars]. Explanation The node has gone online. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.3(1).
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message SVC-6-NODE_INFO_MSG: (SVC [dec]/[dec] SS_ERR_CFG_REMOTE_DELETECONSTGRP ) Remote Copy consistency group deleted [chars]. Explanation The svctask rmconsistgrp IBM CLI command has been invoked. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.3(1).
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message SVC-6-NODE_INFO_MSG: (SVC [dec]/[dec] SS_ERR_CFG_REMOTE_STOP ) Remote Copy relationship stopped [chars]. Explanation The svctask stoprcrelationship IBM CLI command has been invoked. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.3(1).
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message SVC-6-NODE_INFO_MSG: (SVC [dec]/[dec] SS_ERR_CFG_TRIGGER_FC_MAPPING ) Flash Copy mapping started [chars]. Explanation The svctask startfcmap IBM CLI command has been invoked. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.3(1).
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message SVC-6-NODE_INFO_MSG: (SVC [dec]/[dec] SS_ERR_CFG_VDISK_DELETE ) Virtual Disk deleted [chars]. Explanation The svctask rmvdisk IBM CLI command has been invoked. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.3(1).
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message SVC-6-NODE_INFO_MSG: (SVC [dec]/[dec] SS_ERR_CFG_VDISK_MOVE_HWS ) Virtual Disk IO Group changed [chars]. Explanation The svctask chvdisk -iogrp IBM CLI command has been invoked. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.3(1).
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message SVC-6-SVC_SYSLOG_CL_UNJOIN: Node [chars] has left cluster [chars]. Explanation SAN Volume Controller (SVC) interface has left cluster. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.3(1).
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message present. Explanation SVC_BATTERY-SLOT#-2-BATTERY_NOT_PRESENT: Battery [dec] is not The module does not have a sufficient number of batteries. Two batteries are needed. Recommended Action If you purchased Cisco support through a Cisco reseller, contact the reseller directly.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message SVC_BATTERY-SLOT#-2-CONDITIONING_DISABLED: Temperature outside permitted range for battery conditioning (5C-40C). Explanation The temperature of the line card is not within the range to permit battery conditioning. Recommended Action Make sure the temperature of the line card is between 5 and 400C.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message SVC_BATTERY-SLOT#-6-CONDITIONING_COMPLETED: Conditioning of battery [dec] completed successfully. Explanation Conditioning process started for a battery is completed successfully. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.3(1).
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message Explanation SYSMGR-2-CFGSNAPSHOT_ABORTED: Configuration snapshot aborted. An attempt to save a snapshot of the startup configuration has failed. Recommended Action Use the other syslog messages to verify that the problem has been corrected, and then try again. Introduced Cisco MDS SAN-OS Release 1.2(2a).
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message SYSMGR-2-CFGWRITE_ABORTED_DIR: Unable to open the configuration directory. Aborting configuration copy. Explanation The destination location for the startup configuration could not be found.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message SYSMGR-2-CFGWRITE_ABORTED_LOG: Unable to open a log file for the new configuration: [chars] (error-id [hex]). Aborting configuration copy. Explanation An attempt to copy the running configuration to startup configuration has failed because a log file could not be created.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message SYSMGR-2-CONVERT_LIB_NOTFOUND: Conversion library not found for service "[chars]". Explanation The system could not find the conversion library for this service. If you purchased Cisco support through a Cisco reseller, contact the reseller directly.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message SYSMGR-2-FORMAT_FAILURE_SUP_RESET: Failure to format a partition successfully causing sup to reset. The partition used to store nonvolatile persistent storage service (PSS) files could not be formatted successfully. The supervisor will be reset. Explanation If the problem persists, contact customer support.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message Explanation SYSMGR-2-HASWITCHOVER_START: This supervisor is becoming active. A cold switchover has started.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message SYSMGR-2-ISSU_FAILED: The ISSU has failed: [chars] (error-id [hex]). Explanation The nondisruptive upgrade has failed. Recommended Action The switch needs to be rebooted. Introduced Cisco MDS SAN-OS Release 3.1(1).
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message SYSMGR-2-PARSEERR_DUPLICATEDDEPEND: [chars]: duplicated dependency from [chars] for service [chars]. Previous use in [chars]. The system image contains an inconsistent list of services. The initialization of the system cannot proceed further.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message SYSMGR-2-PARSEERR_INVALID_GLOBAL_SYNC: [chars]: mts unaware service may not request for a global sync. The system image contains an inconsistent list of services. The initialization of the system cannot proceed further.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Introduced Cisco MDS SAN-OS Release 1.2(2a). Error Message SYSMGR-2-PARSEERR_INVALIDIDENT: [chars]: [chars] "[chars]" not found for service "[chars]". The system image contains an inconsistent list of services. The initialization of the system cannot proceed further.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message SYSMGR-2-PARSEERR_INVALID_SHELLTREE: [chars]: invalid shell parser tree [chars] for service [chars]: [chars] ([dec]). The system image contains an inconsistent list of services. The initialization of the system cannot proceed further.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message SYSMGR-2-PARSEERR_MISSINGOPTION: [chars]: option [chars]-][chars] missing from service definition for service "[chars]". The system image contains an inconsistent list of services. The initialization of the system cannot proceed further.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message SYSMGR-2-PARSEERR_TOOMANYDEPENDS: [chars]: too many dependencies ([dec]) for service "[chars]". The system image contains an inconsistent list of services. The initialization of the system cannot proceed further.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message ([dec]). Explanation SYSMGR-2-REDSTATE_SETFAILED: Failed to set redundancy state: ret_val The local supervisor is unable to get the redundancy state. If you purchased Cisco support through a Cisco reseller, contact the reseller directly.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message SYSMGR-2-SAVE_RUNTIME_DB_FAILED: Saving of runtime database for fabric switch upgrade failed (error-id [hex]). This message indicates that the runtime database could not be saved for the fabric switch upgrade.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Introduced Cisco MDS SAN-OS Release 1.2(2a). Error Message SYSMGR-2-STARTUP_CONVERSION_FAILED: Startup config conversion failed during boot (error-id [hex]). Explanation The conversion of the startup configuration failed during boot.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message SYSMGR-2-VOLATILE_DB_FULL: System volatile database usage is unexpectedly high at [dec]% Explanation System volatile database space is almost full. Recommended Action Issue the system pss shrink CLI command. If this message continues, contact your technical support representative.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message SYSMGR-3-CFGSNAPSHOT_FAILED: Configuration snapshot failed (error-id [hex]). Explanation The requested configuration snapshot has failed. The error message shows the error ID representing the failure reason. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.2(2a).
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message Explanation SYSMGR-3-COPY_CORES_FAILED: Copying cores failed ([dec]). Copying cores to the destination failed because of an error specified in the log. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.2(2a).
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message SYSMGR-3-GSYNC_TIMEOUT_FAILED: Failed to set timeout for global sync for an application ([dec]). Failed to set the time-out for global synchronization for an application. Global synchronization may be stuck permanently if the application never completes global synchronization.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message SYSMGR-3-INVALID_UUID: Service [chars] is configured with UUID [hex], but uses UUID [hex]. Explanation The identity of a service is inconsistent in the image file. If you purchased Cisco support through a Cisco reseller, contact the reseller directly.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message SYSMGR-3-PARTIAL_CFGWRITE_FAILED: Partial configuration copy failed (error-id [hex]). The requested configuration copy has failed. The error message shows the error ID representing the failure reason. Explanation Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.2(2a).
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message SYSMGR-3-SERVICE_TERMINATED: Service [chars] (PID [dec]) has finished with error code [chars] ([dec]). A service has terminated its execution normally. Depending on the value of the error code and the high availability policies implemented for the service, the service might be restarted automatically.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message SYSMGR-3-UNACCEPTABLE_WAIT: Service [chars], no response from System Manager after [dec] seconds. Terminating. Explanation A spawned service could not handshake with the system manager and was terminated. If you purchased Cisco support through a Cisco reseller, contact the reseller directly.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message SYSMGR-4-ON_DEMAND_STOP_UID_KNOWN: On-demand service "[chars]" stopped by uid ([dec]). The service start type is specified as type on-demand in its configuration file and an external request asked to stop it. Explanation Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.2(2a).
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message Explanation SYSMGR-4-SRVSCOPE_COMPLETED: Completed execution for scope [chars]. Execution completed. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.2(2a). Error Message SYSMGR-4-SRVSCOPE_DELAYED: Waiting for redundancy state; termination delayed for scope [chars].
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message SYSMGR-5-CFGERASE_STARTED: Configuration erase started (PID [dec]). Explanation The requested configuration erase has started. The error message shows the process ID of the process servicing the request. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.2(2a).
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message SYSMGR-5-CFGWRITE_STARTED: Configuration copy started (PID [dec]). Explanation On the active supervisor, this message indicates that the system has started to service a copy running-config startup-config CLI command requested by the user.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message SYSMGR-5-HANDSHAKE_VERIFYING_DONE: Handshake verification done from service "[chars]". Explanation Handshake verified for the listed service. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.3(1).
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Introduced Cisco MDS SAN-OS Release 1.3(1). Error Message SYSMGR-5-PARTIAL_CFGWRITE_DONE: Partial configuration copy successful. Explanation The requested configuration copy has completed successfully. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.2(2a).
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message SYSMGR-5-RUNTIME_DB_SAVE_STARTED: Runtime database save has started (PID [dec]). The system has started to save the runtime database. This happens during the nondisruptive fabric switch upgrade. Explanation Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 2.1(1a).
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message SYSMGR-5-SUBPROC_KILLED: "[chars]" (PID [dec]) hasn’t caught signal [dec][chars]. Explanation This is an internal debugging message. This is not a problem or malfunction. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.3(1). Deprecated Cisco MDS SAN-OS Release 3.0(1).
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Introduced Cisco MDS SAN-OS Release 1.2(2a). SYSMGR-7 Error Message SYSMGR-7-CFGWRITE_UNEXPECTEDRSP: Discarding unexpected response from service "[chars]". Explanation The system manager discarded an unexpected response from a service. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.2(2a).
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message SYSMGR-7-SWITCHOVER_SRVSUCCEDED: Service "[chars]" completed its switchover actions. Explanation The service has completed switchover. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.2(2a).
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m SYSTEMHEALTH Messages This section contains the system health (SYSTEMHEALTH) messages. SYSTEMHEALTH-2 Error Message SYSTEMHEALTH-2-OHMS_BATTERY_FAILED: Battery [dec] failed for module [dec]. Reason: [chars]. Explanation Battery failed. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.3(1).
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message SYSTEMHEALTH-2-OHMS_CACHE_DISK_FAILED: Cache disk [dec] failed for module [dec]. Explanation Cache disk failed. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.3(1). Error Message [dec].
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message SYSTEMHEALTH-2-OHMS_LC_CF_INIT_ERRORS: Compact Flash firmware CRC checksum procedure encountered an error during initialization on module [dec] Reason: [chars]. Explanation Compact Flash CRC checksum initializations failed. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 3.3(1a).
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message SYSTEMHEALTH-2-OHMS_SUP_CF_REFLASH_FAILED: Compact Flash firmware refresh procedure failed, replace the compact flash on module [dec]. Reason: [char]. Explanation Compact Flash firmware corrupted. Recommended Action Schedule a downtime and replace the compact flash on the affected module.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message SYSTEMHEALTH-2-OHMS_TCAM_PARITY_OFLOW: Too many TCAM parity errors detected on module [dec]. Explanation More parity errors than that can be corrected were detected on the affected module. Recommended Action Schedule a downtime and reload the compact flash on the affected module.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message SYSTEMHEALTH-4-OHMS_BOOTFLASH_FAILING: Bootflash starting to fail on module [dec]. Explanation System Health bootflash failing. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.3(4a). Deprecated Cisco MDS SAN-OS Release 1.3(4b).
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message SYSTEMHEALTH-4-OHMS_CDISK_FAILING: Cache disk [dec] starting to fail on module [dec]. Explanation System Health cache disk failing. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.3(4a). Deprecated Cisco MDS SAN-OS Release 1.3(4b).
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message SYSTEMHEALTH-4-OHMS_EOBC_FAILING: EOBC starting to fail on module [dec]. Explanation System Health Ethernet out-of-band channel failing. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.3(4a). Deprecated Cisco MDS SAN-OS Release 1.3(4b).
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message SYSTEMHEALTH-4-OHMS_INBAND_TEST_ERRORS: Too many errors while running the inband test. Explanation Inband test has had too many errors while running. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.3(1).
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message SYSTEMHEALTH-4-OHMS_NVRAM_ERRORS: Too many errors on module [dec] while running the Nvram test. Explanation NVRAM test has had too many errors while running. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 3.0(1).
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message SYSTEMHEALTH-4-OHMS_SUP_CF_CRC_INIT_ERRORS: Compact Flash firmware CRC checksum procedure encountered an error during initialization on module [dec] Reason: [chars]. Explanation Compact Flash CRC checksum initializations failed.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message SYSTEMHEALTH-4-OHMS_SVC_DAEMON_FAILED: System Health process running on module [dec] SVC node [dec] exited due to errors. Explanation Online system health San Volume Controller (OHMS SVC) daemon exited. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.3(4a).
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message SYSTEMHEALTH-4-STB_ARB_MAX_FAIL: Standby Arbiter test MAX failures reached. Explanation Standby arbiter test maximum failures reached. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.2(2a). Deprecated Cisco MDS SAN-OS Release 1.3(1). Error Message reached.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message SYSTEMHEALTH-5-OHMS_EMGMT_FAILING: Management port on module [dec] starting to show signs of failures. Explanation System Health Ethernet management failing. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.3(4b). Error Message [dec].
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message SYSTEMHEALTH-5-OHMS_TCAM_PARITY_CLEARED: Failing conditions for TCAM on module [dec] have been cleared. Explanation System Health TCAM failures cleared. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 3.3(1a).
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message SYSTEMHEALTH-6-OHMS_BOOTFLASH_CLEARED: Failing conditions for bootflash on module [dec] have been cleared. Explanation System Health bootflash failures cleared. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.3(4a).
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message SYSTEMHEALTH-6-OHMS_INBAND_DROP: Inband Dropping frames from module [dec] due to unknown reasons. Explanation System Health inband non-timeout drop. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.3(4a).
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m TACACS Messages This section contains the Terminal Access Controller Access Control System Plus (TACACS+) messages. TACACS-2 Error Message TACACS-2-TACACS_PROGRAM_EXIT: TACACS+ daemon exiting: [chars]. Explanation Terminal Access Controller Access Control System Plus (TACACS+) daemon is exiting.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m TACACS-3 Error Message TACACS-3-TACACS_ERROR_MESSAGE: [chars]. Explanation Terminal Access Controller Access Control System Plus (TACACS+) error message. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.3(1). TACACS-6 Error Message Explanation TACACS-6-TACACS_ACCOUNTING_MESSAGE: [chars].
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m TCAP Messages This section contains the terminal capture (TCAP) messages. TCAP-2 Error Message Explanation TCAP-2-MEM_FULL: Memory allocation failed. Terminal capture process has failed to allocate memory.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m TLPORT Messages This section contains the translation port (TLPORT) messages. TLPORT-2 Error Message Explanation TLPORT-2-INITFAIL: TL Port Manager Initialization failed: [chars]. TL port manager initialization failed. The error message explains the reason for the failure. Recommended Action No action is required.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message TLPORT-3-MTSERROR: [chars]. TL port manager encountered a messaging and transaction service (MTS) error. The error message specifies the context where the error occurred. Explanation Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.2(2a).
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message TLPORT-6-PORTDOWN: Translation Port [chars] DOWN. Explanation A port configured as a TL port is down and out of operation. The error message shows the Interface-ID string that identifies the TL port. This is an informational message. Recommended Action No action is required.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message TPC-SLOT#-5-LOG_ERR_TPC_VT_DESTROYED: VSAN :[dec] Virtual Target : [chars] Deleted. Explanation The virtual target in the associated VSAN is being destroyed. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 3.0(1). Error Message VSAN down.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m TTYD-3 Error Message Explanation TTYD-3-TTYD_MISC_ERROR: Error [chars] with error [chars]([hex]). Miscellaneous TTY daemon (TTYD) problems. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.2(2a). TTYD-6 Error Message Explanation TTYD-6-TTYD_MISC: TTYD [chars].
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message VEC-SLOT#-3-LOG_ERR_DISK: VSAN [chars] SENSE_KEY([chars] ASC([chars]. Explanation An error occurred. SENSE_KEY and ASC refer to the ANSI T10 SP3 SCSI specification at http://www.t10.org Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.2(2a). Deprecated Cisco MDS SAN-OS Release 1.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message VEC-SLOT#-5-LOG_ERR_VEC_DPRLI_FSM: Illegal Event [chars] in State [chars] FSM [chars]. Explanation An event is received for a state in the virtual enclosure client (VEC) distributed process login (DPRLI) finite state machine (FSM) that should not have occurred. Recommended Action No action is required.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message VEC-SLOT#-5-LOG_ERR_VEC_HOST_XP_FSM: Illegal Event [chars] in State [chars] Host VSAN :[dec] Host pWWN :[chars] VEP pWWN :[chars]. An event is received for a state in the virtual enclosure client (VEC) HOST XP finite state machine (FSM) that should not have occurred.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message VEC-SLOT#-5-LOG_ERR_VEC_TP_FSM: Illegal Event [chars] in State [chars] Host VSAN :[dec] TP nWWN :[chars] TP pWWN :[chars]. An event is received for a state in the virtual enclosure client (VEC) TP finite state machine (FSM) that should not have occurred. Explanation Recommended Action No action is required.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message VEC-SLOT#-5-LOG_ERR_VEC_VSAN_FSM: Illegal Event [chars] in State [chars] VSAN [dec]. Explanation An event is received for a state in the virtual enclosure client (VEC) VSAN finite state machine (FSM) that should not have occurred. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m VEDB_MGR Messages This section contains the virtual enclosure database (VEDB_MGR) messages. VEDB_MGR-2 Error Message Explanation VEDB_MGR-2-MALLOC_ERROR: Size [dec] bytes. The virtual enclosure database (VEDB) library could not allocate memory.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m VES Messages This section contains the virtual enclosure server (VES) messages. VES-SLOT#-4 Error Message VES-SLOT#-4-LOG_WARNING_VES_CONFIG_TOO_BIG: Volume [chars] configuration too large to virtualize. Explanation The VES maximum volume configuration was exceeded.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message VES-SLOT#-5-LOG_ERR_VES_VSAN_XCHG_FSM: Illegal Event [chars] in State [chars] VEC IP Addr [chars]. An event is received for a state in the virtual enclosure server (VES)VSAN XCHG finite state machine (FSM) that should not have occurred. Explanation Recommended Action No action is required.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message Explanation VFC-6-STARTING: deamon started. The virtual Fibre Channel (VFC) daemon successfully started. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 2.0(1b). VHBAD Messages This section contains the virtual host bus adapter daemon (VHBAD) messages.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message VHBAD-2-PROC_WWNM_GET_WWN_FAIL: Failed to get local controller pwwn from WWN Manager error: [hex] response: [hex]. Explanation SCSI target process used the wwnm_bwt_get_local_controller_wwn() API for the port WWN and it failed because of the error and response code shown in the error message.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message VHBAD-3-PSS_DELETE_FAIL: pss delete runtime entry key:[hex] failed due to error: [hex]. SCSI target process persistent storage service (PSS) delete runtime entry key failed because of the error shown in the error message.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message VHBAD-3-PSS_SNAPSHOT_DEBUG_FAIL: pss snapshot runtime debug to uri:[chars] failed due to error: [hex]. Explanation SCSI target process persistent storage service (PSS) snapshot of runtime debug to URI failed because of the error shown in the error message.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m VNI Messages This section contains the virtual network interface (VNI) messages. VNI-2 Error Message Explanation VNI-2-ALLOC_MEMORY: Memory allocation failed. The service failed to allocate a block of dynamic memory. Recommended Action Check the system memory. If system memory is low, reset the switch.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message VNI-6-VSAN_DELETED: VSAN [dec] has been deleted. Explanation The specified VSAN has been deleted. The service deleted all the configuration on that VSAN. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.2(2a). VOMD-SLOT Messages This section contains the VOMD-SLOT messages.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message VPM-2-PSS_ERROR: [chars]. Explanation The virtual port manager encountered an error while operating on a persistent storage database. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.2(2a). Error Message Explanation VPM-2-VPMON_CRIT: [chars] [dec].
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message VPM-3-SEND_TO_ILC_FAILED: [chars]. The virtual port manager could not send to the intelligent line card.(ILC for DG=%s, at slot=%d processor=%d and SAP=%d). Explanation If you purchased Cisco support through a Cisco reseller, contact the reseller directly.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m VPM-6 Error Message VPM-6-BECAME_ACTIVE: Became ACTIVE from standby mode. The virtual port manager on the standby supervisor became active and it is ready to serve client requests. Explanation Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.2(2a).
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message VPM-6-FAILED_TO_SEND_HEARTBEAT: Failed to send heartbeat to system manager: Reason=[chars]. Explanation The virtual port manager was unable to send a heartbeat to the system manager. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.2(2a).
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message Explanation VPM-6-VPMON_INFO: [chars]. A virtual port manager informational message. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 2.0(1b). Error Message Explanation VPM-6-VPMON_STARTING: deamon started. The virtual port manager daemon successfully started.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m VPM-SLOT# Messages This section contains the virtual port manager slot (VPM-SLOT) messages. VPM-SLOT#-2 Error Message VPM-SLOT#-2-CPP_CATASTROPHIC_ERROR: ERROR: Component ([chars]) caused critical error please reboot ILC. Explanation The listed component caused a critical error. Recommended Action Restart the line card.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m VRRP_CFG-5 Error Message VRRP_CFG-5-STARTING: VRRP Manager service started. Explanation The service successfully started. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 3.0(1). Error Message VRRP_CFG-5-VR_ADMIN_DOWN: VR [chars]group [dec] on interface [chars] is administratively down.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m VRRP_CFG-6 Error Message Explanation VRRP_CFG-6-STARTING: VRRP Manager service started. The service successfully started. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.2(2a). Error Message VRRP_CFG-6-VR_CREATED: VR group [dec] created on interface [chars].
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message VRRP_ENG-2-INVALID_CONFIG: Cannot start the VR [dec] on the interface [chars]. Invalid IP configuration. Reason: [chars]. The specified virtual router on the interface is enabled, but the IP configuration is not valid because of the error shown in the error message.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m VRRP_ENG-5 Error Message VRRP_ENG-5-INTERFACE_DOWN: Cannot start the VR[chars] [dec] since the interface [chars] is down. Explanation The specified VR is enabled but cannot change state from init. The specified interface is down or does not have a primary IP address configured. Recommended Action No action is required.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message VRRP_ENG-6-INTERFACE_DOWN: Cannot start the VR [dec] since the interface [chars] is down. The specified virtual router is enabled but cannot change state from initializing. The specified interface is down or does not have a primary IP address configured. Explanation Recommended Action No action is required.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m VSAN Messages This section contains the virtual SAN (VSAN) messages. VSAN-2 Error Message VSAN-2-PROGRAM_EXIT: process exiting with reason: [chars]. Explanation The Virtual SAN (VSAN) manager process is exiting with the reason shown in the error message.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m VSAN-6 Error Message Explanation VSAN-6-ACTIVATED: VSAN:[dec] changing from suspended to active. Making VSAN (with ID shown in the error message) active from suspended state. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.2(2a).
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message VSAN-6-TRUNKING_MEMBERSHIP_UPDATE: trunking membership updated for interface:[chars] with VSAN bitmap:[chars]. Explanation Updated trunking membership for the interface with the allowed VSAN list. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.2(2a).
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message Explanation VSHD-3-VSHD_SYSLOG_MTS_ERR: message [chars]. Messaging and transaction service (MTS) message handling error. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.2(2a). Error Message Explanation VSHD-3-VSHD_SYSLOG_PARSE_TREE_ERR: [chars].
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message VSHD-4-VSHD_ROLE_DATABASE_VERSION_NOT_UNDERSTOOD: This switch does not understand the version of role configuration database received during merge. Explanation This is probably occurring due to different versions of system image on switches in the fabric.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m WWN Messages This section contains the World Wide Name (WWN) messages. WWN-1 Error Message WWN-1-TYPE1_ALERT: [dec] (< [dec] %) Remain. Explanation The WWN manager has run out of WWNs. No new dynamically allocated WWNs are available.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message WWN-2-GENERAL_ERROR: [chars]. Explanation The WWN manager has encountered a critical error. The description of error is shown in the error message. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.2(2a). Error Message Explanation WWN-2-MALLOC_ERROR: Size [dec] bytes.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message WWN-2-TYPE1_CRIT: [dec] (< [dec] %) Remain. Explanation The WWN manager has only the shown percent or less of WWNs remaining. Recommended Action Add additional WWNs by programming a new secondary MAC address and its range. Introduced Cisco MDS SAN-OS Release 1.2(2a).
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message WWN-3-STARTUP_COPY_TO_RUNNING_FAILED: [chars]. Explanation Could not snapshot Startup-Config PSS to Running-Config. The description of error is [str.]. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message WWN-4-PSS_VERSION_MISMATCH: PSS [dec] Code [dec]. There was a version mismatch between the WWN manager and one of its persistent storage databases. The persistent information has been translated to the new format. Explanation Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message WWN-6-BECAME_ACTIVE: Became ACTIVE from standby mode. Explanation The WWN manager on the standby supervisor module became active and it is ready to serve client requests for WWNs. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.2(2a).
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message Explanation WWN-6-PSS_DESTROYED: [chars] PSS Destroyed. One of the persistent information databases has been intentionally destroyed and was recreated. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.2(2a). Error Message Explanation WWN-6-RELEASED_BLOCK: Block number [dec].
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m XBAR Messages This section contains the crossbar (XBAR) messages. XBAR-3 Error Message Explanation XBAR-3-MEM_FULL: Memory allocation failed. Memory allocation failed. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.2(2a).
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message XBAR-5-MOD_CONNECTION_REATTEMPT: Re-attempting Xbar connection with module [dec]. Explanation The module has experienced a setup failure on connecting the module to the fabric.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message XBAR-5-XBAR_PORT_DISABLE_FAIL: Xbar [[dec].[dec]] reported failure to disable port [dec] return_code [hex] ([chars]). Explanation The supervisor has experienced an xbar setup failure. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 3.0(1).
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message XBAR-5-XBAR_SET_ACCESS_FAIL: Slot [dec] reported failure acquiring [chars] xbar access return_code [hex] ([chars]). Explanation The supervisor has experienced an xbar access failure. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 3.0(1).
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message Explanation XBAR_CLIENT-2-PROC_DN: Process is shutting down: [chars]. The crossbar client process is exiting. Enter the show xbar-client event-history command or use a similar Fabric Manager/Device manager procedure to collect more information. Recommended Action Introduced Cisco MDS SAN-OS Release 1.2(2a).
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m ZONE Messages This section contains the zone messages. ZONE-2 Error Message [chars]. ZONE-2-LZ_EXITING: LUN/Read-only Zoning Process exited. Reason: Explanation The LUN read-only zoning process has exited because of the reason shown in the error message . The process restarted automatically.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message ZONE-2-ZS_ALIAS_LIMIT_EXCEEDED: The limit for maximum number of aliases exceeded. The number of aliases configured has exceeded the maximum number of aliases allowed per VSAN. Because of this, a distribution or merge operation may fail.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message ZONE-2-ZS_CHANGE_ACTIVATION_FAILED_RESN_DOM: Activation failed : reason [chars] domain [dec]. Explanation The zone server cannot activate because of reason shown in the error message on the domain. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.2(2a).
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message Explanation ZONE-2-ZS_CHANGE_SFC_FAILED: SFC failed : [chars]. The zone server cannot stage the zone configuration. Recommended Action Verify the interoperability mode on all the switches. Introduced Cisco MDS SAN-OS Release 1.2(2a).
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message ZONE-2-ZS_CHANGE_STAGE_DISTRIBUTE_ZS_DB_FAILED: Stage distribute zoneset database failed on VSAN [dec]. Explanation The zone server cannot stage distribute zone set database on the VSAN. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 2.0(1b).
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message ZONE-2-ZS_FIPS_COMPLIANCE_FAILURE: FIPS compliance error: consecutively same random numbers. Explanation FIPS compliance error identifying the same random numbers. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 3.1(1). Error Message ZONE-2-ZS_INIT_FAILED: [chars].
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message ZONE-2-ZS_LUN_MEMBER_LIMIT_EXCEEDED: The limit for maximum number of lun members exceeded. Explanation The number of LUN members configured has exceeded the maximum number of LUN members allowed across all VSANs. Because of this, distribution or merge operation may fail.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message ZONE-2-ZS_MERGE_FULL_DATABASE_MISMATCH: Zone merge full database mismatch on interface [chars]. Explanation Full zoning databases are inconsistent between two switches connected by an interface. Databases are not merged. Recommended Action Compare full zoning database with the adjacent switch.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message ZONE-2-ZS_PSS_VER_MISMATCH: PSS version mismatch URL: [chars] (expected [chars], got [chars]). Configuration version mismatch. persistent storage service (PSS) URL expected the shown version, but the stored version is different. Explanation Recommended Action Upgrade or downgrade to the expected version.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message ZONE-2-ZS_TCAM_SWITCHED_TO_SOFT_ZONING_MODE: Switched to soft zoning : Reason: Hard zoning disabled. Explanation Switched to soft zoning. Hard zoning was disabled due to a TCAM programming failure. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 3.1(1).
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message ZONE-3-ZS_ACTIVATION_FAILED_DUE_TO_QOS_DISABLED: Activation failed due to qos not enabled. Explanation Activation of zone set failed because QoS was not enabled. Recommended Action Make sure QoS is enabled and reactivate the zone set in the VSAN. Introduced Cisco MDS SAN-OS Release 2.0(1b).
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message Explanation ZONE-4-ZS_DB_WARNING: [chars]. Database operation warning. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.2(2a). Error Message ZONE-4-ZS_DOMAIN_MGR_WARNING: Unable to retrieve domain info from domain mgr error: [chars] in vsan [dec].
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message ZONE-4-ZS_NON_INTEROPERABLE_ZONE_SET: Non interoperable active zoneset present on VSAN [dec] in interoperability mode. Explanation Active zone set has non-interoperable members (FC ID, FWWN) when interoperability mode is turned on for the VSAN.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message ZONE-5-ZS_POLICY_CHANGE: Default zoning policy changed to [chars]. Explanation Default zoning policy changed to permit or deny. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.2(2a). Error Message Explanation ZONE-5-ZS_ZONE_SET_ACTIVATED: Zoneset [chars] activated.
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message ZONE-6-LZ_GENERAL_EVENT: [chars]. Explanation The LUN read-only zoning process has generated an important event. The description of the event is shown in the error message. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.2(2a).
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Error Message ZONE-6-LZ_SWITCHOVER: LUN/Read-only zoning process switching over to other supervisor. The LUN read-only zoning process has successfully switched over to the standby supervisor module. Explanation Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.2(2a).
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o .
Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m A P P E N D I X A OHMS_BOOTFLASH_ERRORS Revised: November, 2007 OL-15956-01 DISK FAILURE CODES List of all Disk Failure Codes are described in (Table A-1). Table A-1 OHMS_BOOTFLASH_ERRORS Description Reason Code Acronym Description 0 OD_DISK_TESTED_OK No Error. 1 OD_DISK_FAILED_PWR Disk returned unknown power state. 2 OD_DISK_FAILED_RAW_READ Unable to read raw blocks.
Appendix A OHMS_BOOTFLASH_ERRORS DISK FAILURE CODES Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m Table A-1 Reason Code OHMS_BOOTFLASH_ERRORS Description (continued) Acronym Description 17 OD_DISK_IOCTL_GET_RESET_INFO_FAI Ioctl to get current reset information LED failed. 18 OD_DISK_IOCTL_RET_STATE_STANDBY Disk is in the standby power state. 19 OD_DISK_IOCTL_DRIVE_RESET_FAILED Disk reset procedure failed.
