© Copyright Hewlett-Packard Company 1998 All rights are reserved. No part of the document may be photocopied, reproduced, or translated to another language without the prior written consent of Hewlett-Packard Company. Note: Regulatory information can be found in Chapter 9 of this User’s Guide. Publication number: C5370-90000 First edition: February 1998 Printed in U.S.A.
Owner’s Information Please complete the following for future reference. HP Color Copier Model _________ Serial Number: Date of Purchase: Place of Purchase: Address: Phone Number: Service Contract Number: Date of Contract Expiration: Safety Symbols ! If present, this symbol is placed on the copier where it is necessary for you to refer to the manual in order to understand a hazard. If present, this symbol is placed on the copier within the area where hazardous voltage is present.
contents Chapter 1 — Welcome! About Your Copier . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2 About This Guide. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2 Conventions Used . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2 Chapter 2 — Setting Up Your New HP Color Copier Copier Location and Environment. . . . . . . . . . . . . . . . . . . . . . . .
Automatic Document Feeder Requirements. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-4 How to Order Quality HP Papers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-4 Chapter 5 — Troubleshooting How to Clear a Paper Jam in the Paper Tray . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1 How to Clear a Paper Jam in the Automatic Document Feeder . . . . . . . . . . . . . . . 5-2 How to Use the Self Test Page . . . . . . . . . . . . . . . . . . . . . .
Prepare your HP Color Copier for Shipment . . . . . . . . . . . . . . . . . . . . . . . . . 8-5 Chapter 9 — Technical Information Regulatory Notices. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-3 Ordering Accessories and Supplies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
vi Contents
Welcome! 1 Welcome to your new Hewlett-Packard Color Copier! And welcome to this User’s Guide, which will help you set up and use your Color Copier.
About Your Copier With your HP Color Copier, you can produce high-quality color and black and white copies on letter- (8.5 x 11 in.) and A4(210 x 297 mm, the European standard) sized paper. You can print on a variety of paper types, including plain paper, premium inkjet paper, photo paper, transparency film, and iron-on transfers.
Setting Up Your New HP Color Copier 2 This chapter presents recommendations for placement of your HP Color Copier and presents the nine simple steps for unpacking and setting up your copier. Be sure to perform the steps in the order listed. Copier Location and Environment Use only within normal office temperature and humidity ranges. The recommended range is 59o–95oF (15o–35oC) and 20%–80% humidity ranges.
Step 1 — Unpack Your HP Color Copier 1 Remove the cardboard tray containing the accessory items. 2 Rest the box on its side and pull out your HP Color Copier. 3 Remove the packing material and the orange packing tape from the outside of the copier. TIP Save the packing materials in case you ever need to move or ship your HP Color Copier. 4 2-2 Remove the two yellow/orange plastic inserts from the print tray by pulling up and toward the center of the copier.
5 Verify that the following items are included with your HP Color Copier: a b c d e front-panel overlay (has text on it) one black and one color print cartridge User’s Guide power cord (appropriate for your location) Help card If any of the items are missing or damaged, contact the dealer from whom you purchased your HP Color Copier. e d c a b Step 2 — Attach the Front Panel Overlay 1 Align the front panel overlay with the front panel buttons.
Step 3 — Unlock Your HP Color Copier The scanner lock is under the front panel. Unlock the scanner by twisting the green knob under the front panel toward the back of your HP Color Copier, until it stops. The knob only turns one way. NOTE 2-4 Leave the scanner unlocked unless you need to move your HP Color Copier. Locking the scanner protects it during moving. Refer to “Prepare your HP Color Copier for Shipment” on page 8-5 for locking instructions.
Step 4 — Load Paper Into Your HP Color Copier NOTE 1 Remove the yellow/orange shipping inserts from the paper tray, if you have not already done so. 2 Slide the paper width and length adjusters to their outermost positions. 3 Insert a stack of up to 150 sheets of paper into the bottom (IN) tray, print side down, until it stops. The output tray can hold a maximum of 50 sheets. If you making more than 50 copies, remove the excess copies from the output tray.
Step 5 — Insert the Color and Black Print Cartridges 1 TIP NOTE Keep and store the shipping insert and other packing materials in case you ever need to move or ship your copier. If your copier has an automatic document feeder, use the print cartridge access cover to prop open the document cover while you insert the print cartridges. 2 2-6 Lift the document cover, open the print cartridge access cover, and remove the yellow/orange shipping insert from the inside of the cartridge cradles.
3 Remove the color print cartridge (the thicker one, part number C1823A) from its package and, being careful to touch only the black plastic, gently remove both the green pull tab and blue tape covering the nozzles. tri-color print cartridge, part number C1823A CAUTION NOTE black print cartridge, part number C51645A Be careful not to touch the gold-colored contacts. 4 Push the color print cartridge firmly down into the cradle on the left, and close the cartridge latch.
Step 6 — Connect the Power Cord The HP Color Copier comes with a power cord for the country to which it is shipped. If the plug on your power cord does not look familiar, contact your dealer or local HP Sales and Support Office. See “HP Customer Support” on page 6-2 for more information. WARNING Power is present in the product even if the white button is off. To completely shut off power, you must disconnect the power cord.
Step 7 — Set the Front Panel Language and Default Paper Size The front panel initially displays English as the default language and assumes letter-sized paper (8.5 x 11 in.) as the default paper size. To change the default language and associated paper size, perform the following steps. 1 While holding down the Select/Resume button, press the Color Intensity button. 2 Release both buttons. The current language is displayed.
Step 8 — Align Your Black and Color Print Cartridges Before you start using your HP Color Copier, you need to align the black and color print cartridges to ensure the best copy quality. When you turn on your HP Color Copier for the first time, you will see the message “Initializing,” followed by the message “Press Resume to Align Cartridges” on the front panel display. 1 Press the Select/Resume button. The copier prints a page with two sets of paired lines on it.
4 Now look closely at the set of vertical bars, and determine which set lines up the best. 5 Select the letter that represents the best vertical alignment on the page, and press Select/Resume. If necessary, use the Plus (+) and Minus (–) buttons on the front panel to change the letter on the display. 6 The HP Color Copier then prints another page to confirm that the print cartridges are correctly aligned. 7 Match the alignment in Sample 2 to the alignment in Sample 1.
Step 9 — Test the Copier Use the copier’s built-in Self Test to verify that the copier is operating properly. The Self Test Page lists current front panel settings and, if you are using Model 145 or 155, tells whether the automatic document feeder is attached properly. 1 Make sure the Best, Normal, or Fast light is on and not blinking. 2 Press the Menu button until the message “Self Test Page” appears in the panel display. 3 Press the Select/Resume button.
Copying 3 This chapter explains how to make copies and how to use the special copying features of the HP Color Copier. It also explains how to use other features on the copier front panel and special considerations of the automatic document feeder (Models 145 and 155 only). How to Make Copies 1 NOTE If it is not already on, turn on the HP Color Copier by pressing the white button on the lower right front corner of the product.
2 Manually (on the copy glass): Lift the document cover, place the original face down on the glass along the two green borders, and close the document cover. Put the long edge of your original along the longer green border. NOTE Be sure to place all originals, including small photographs, in the corner along the two green borders. Some features of the HP Color Copier look for items specifically in that corner.
3 If you are making more than one copy, press the Plus (+) button or the Number of Copies button followed by the Plus (+) button until the appropriate number is displayed on the front panel. 4 Adjust the way your copy will look using the Copy Quality, Reduce/Enlarge, Lighter/Darker, and Color Intensity buttons. See “Controlling How Copies Will Look” later in this chapter for details. 5 Start copying: Press the Black button to make a black and white copy.
Number of Copies You can specify the number of copies to make in either of two ways: When “1 copy” is displayed on the front panel, press the Plus (+) button. Press the Number of Copies button, then press the Plus (+) button. Copy Quality The Copy Quality button changes the speed and quality of the copies you make.
Auto Fit pre-scans the original to determine where its edges are. Auto Fit then reduces or enlarges the original to fit on the paper you are copying onto. When enlarging, Auto Fit increases the size of the copy to the largest size that will fit on the page without distorting the image, and centers the image on the page. NOTE Use Auto Fit or Entire 91% to slightly reduce your original and ensure that you copy the entire page.
Mirror 100% (– +) reverses the image of your original and makes a copy based on the percent reduction/enlargement you specify. You can use Mirror to copy favorite photos or images onto HP Iron-On T-Shirt Transfers. Then iron the image to make custom t-shirts, banners, and flags. You can also use Mirror to copy presentation materials onto HP Premium Transparency Film. Then, when you flip each film over to make your presentation, you can write on it and erase, without worrying about smearing the ink.
To make copies Lighter or Darker: 1 Press the Lighter/Darker button. The range of lightness/darkness values appears on a scale on the display. 2 To make your copy darker, press the Plus (+) button. The dot moves to the right. To make your copy lighter, press the Minus (–) button. The dot moves to the left. 3 Press Select/Resume to confirm your selection. Color Intensity Use the Color Intensity feature to make the colors on your copy more vivid or more subtle.
To turn TE On/Off: 1 Press the Menu button until “TE” appears on the front panel display. 2 Press the Plus (+) and Minus (–) buttons to switch between (off) and z (on). 3 Press Select/Resume to confirm your selection. ELC (Enhance Light Colors) Use the Enhance Light Colors (ELC) setting to enhance light-color backgrounds in documents, such as maps, photos, and invoices, so the background is included on the copy. The ELC feature improves the appearance of very pale colors.
2 Press the Plus (+) or Minus (–) button to scroll through the available languages until the language you need appears. The following languages are available: English, Español, Deutsch, Français, Italiano, Nederlands, Dansk, Norsk, Portugués, Svenska, and Suomi. 3 Press Select/Resume to choose the displayed language. Copy Paper Size With your HP Color Copier, you can copy on either Letter(8.5 x 11 inches) or A4- (210 x 297 mm) sized paper.
3 Press the Menu button until “Set Defaults” appears on the front panel display. 4 Press the Select/Resume button. The message “Current settings saved as defaults” is displayed. (This step saves the new setting—Auto Fit—as your default.) Factory Defaults You can return all the control panel settings to their factory defaults at one time. To return to Factory Defaults: 1 Press the Menu button repeatedly until you see “Factory Defaults” on the front panel display. 2 Press Select/Resume.
Using the Automatic Document Feeder (ADF) With the automatic document feeder (Models 145 and 155 only), you can feed up to 25 originals at a time. You can use etter-sized or A4-sized originals in the feeder. Here are some other tips: Always feed your originals with the printed-side facing back in the document feeder, and the top of the document to the right. Do not mix paper types or sizes in the ADF. Load only originals printed on 16-24 lb. paper in the document feeder.
3-12 Copying
4 All About Paper This chapter explains the paper types you can use when copying. It also presents some tips on loading paper and transparency film, and sets forth paper requirements for originals used in the automatic document feeder. For a current list of HP copier papers, visit our website: http://www.hp.com/go/copiers/paper Paper Choices When Copying The HP Color Copier is designed to copy onto a variety of paper types and weights.
HP Photo Paper is a high-quality, glossy-finish, photo-based inkjet paper. It looks and feels like a photograph and can be mounted under glass or in an album. HP Photo paper dries rapidly and resists fingerprints and smudges. HP Iron-On T-Shirt Transfers can be used to transfer your designs or photos onto t-shirts, sweatshirts, and fabric crafts. Use the ordering information on page 9-4 for paper sizes, types, and part numbers. NOTE See page 4-4 for automatic document feeder paper requirements.
Using the Right Paper Type Option The Paper Type option you select determines how the HP Color Copier prints on the paper you are using. Each time you load a different type of paper in the paper tray or document feeder, be sure to set the corresponding Paper Type option on the front panel.
Special Considerations When Using Transparency Film NOTE Load a maximum of 80 transparency sheets at a time. Be sure to specify “Transparency” as the Paper Type setting. Ink dries slower on film. Be sure to allow enough time for the ink to dry before using the transparency. If you are copying from a transparency (that is, your original is printed on transparency film), place a blank piece of paper over the transparency on the copier glass.
5 Troubleshooting This chapter presents procedures for resolving paper jams in the paper tray and automatic document feeder (Models 145 and 155 only). It also includes lists common copying problems and their solutions. How to Clear a Paper Jam in the Paper Tray The message “Paper Jam” appears on the display when paper cannot feed from the paper tray properly. To resolve this problem: 1 Press and hold down the Select/Resume button.
5 If all else fails, remove the paper tray by pinching together the two levers under the paper tray. Pull the tray toward you, and gently remove the jammed paper. Then slide the paper tray back into the copier. 6 Turn the copier off, then on again to continue copying. If paper has jammed in the copier, but no message is displayed, press and hold down the Select/Resume button, then the Paper Type button. Then follow the directions above.
3 4 Check to make sure the margins are aligned and not skewed. a Fold the Self Test Page in half carefully so that the “A” and the “C” along the left margin line up. b Line up the equal signs (=). c Verify that the vertical line next to the “A” appears between the two vertical lines next to the “C” (does not have to be centered). If the alignment is satisfactory, the copier mechanism is working properly. If the alignment is not satisfactory, see Troubleshooting information on page 5-11.
Front Panel Messages Message What You Should Do Power Save On The front panel displays this message when the OfficeJet Pro has not been used for 12 hours or more. Press any button on the front panel or load originals in the automatic document feeder. Door Open. Close cartridge door. Close the print cartridge door. Paper Jam. Press and hold Resume to eject paper. To clear the paper jam, press and hold the Select/Resume button. The paper should eject.
Front Panel Messages (Continued) Message What You Should Do Remove and check color cartridge. Verify Part Number: C1823A The wrong tri-color cartridge is installed. Remove it, and replace it with the correct cartridge, part number C1823A. Unlock scanner. The scanner is locked. Turn off the HP Color Copier. The scanner lock is located beneath the front panel on the right side. Unlock the scanner by twisting the green knob under the front panel toward the back of your HP Color Copier, until it stops.
Blank page (Continued) Possible Causes Solutions The print cartridges need to be replaced. The HP Color Copier black or color cartridge may need to be replaced. The best way to check this is to print a Self Test Page. (See the procedure on page 2-12.) If any of the colored bars are missing (blue, magenta, or yellow), the color print cartridge must be replaced. You are making a large Custom % enlargement, and have not positioned the original along the green borders.
Placement on the page wrong or edges cut off (Continued) Possible Causes Solutions The Paper Size setting on the front panel is set to A4, and letter-size paper is loaded, or the Paper Size setting is set to letter, and A4-size paper is loaded. Check to make sure that Paper Size is set correctly. See “Copy Paper Size” on page 3-9. Auto Fit, Clone, or Poster not working properly Possible Causes Auto Fit does not enlarge to full size. The Clone feature does not make enough duplicate copies.
No copies coming out (Continued) Possible Causes Solutions The HP Color Copier may not be turned on. Turn the HP Color Copier on by pressing the Power button on the front of the product in the bottom right corner. The current Copy Quality setting will light up, and a message will appear on the front panel. The paper has jammed in the copier. Clear the paper jam using the procedure on page 5-1. Copies taking too long Possible Causes Solutions You are using the Best copy quality setting.
Paper wrinkled and very wet (Continued) Possible Causes Solutions You are copying a page with very dark colors. Press the Lighter/Darker button. Press the Minus (–) button to lighten your copy. The round dot moves to the left on the scale. You can also press the Color Intensity button to decrease the intensity of the colors. Press the Minus (–) button to reduce the color intensity and make your copy paler. The round dot moves to the left on the scale.
Copy streaked, smeared, or with white horizontal lines Possible Causes Solutions The Paper Type setting does not match the paper loaded in the paper tray. If you are using special papers, such as photo, premium inkjet, iron-on, or transparencies, you need to make sure the Paper Type setting you selected matches the type of paper you have in the bottom tray. Press the Paper Type button until the paper type on the display matches the type of paper you have loaded in the bottom tray.
Black bar in margins on copy (Models 145 and 155 only) Possible Causes Solutions You are copying an original that is greater than 8” wide, and the solution above did not solve the problem. Place the original on the glass and place white sheets of paper on toe of the original to cover the entire glass. . Copies crooked on page Possible Causes Solutions The original is crooked on the glass. Reposition the original against the green borders.
Miscellaneous problems (Continued) Symptoms Solutions White lines on copies appear between adjacent black and color areas, or black and color overlap. The print cartridges may need to be aligned: Press the Menu button until “Align Print Cartridges” appears on the display. Press the Select/Resume button; instructions are printed. Follow the instructions that are printed. Unwanted dots appear in the background. This often occurs if you are copying from a gray or pastel original.
Miscellaneous problems (Continued) Symptoms Paper repeatedly jams or the copier tears the corner of the paper. Solutions The wrong size paper is loaded. Load the correct size paper. The leading edge is damaged or bent. Do not use damaged paper. The paper width and length adjusters are not set correctly. Be sure the paper width and length adjusters on the bottom tray are set for your paper size. The paper may be damaged or curled. Replace damaged or curled paper.
5-14 Troubleshooting
HP Support Services 6 If you are unable to find the answer you need in this book, you can contact one of the HP support services listed in the following pages. Some support services are available only in the U.S. and Canada, while others are available in many countries worldwide. If a support service number is not listed for your country, contact your nearest authorized HP dealer for help.
CompuServe Support information and interactive sharing of technical information are available on CompuServe’s HP Peripherals forum GO HPPER. To subscribe, call CompuServe, Inc. at (800) 848-8199 (U.S.). NOTE This service is not operated by HP. HP Customer Support If you are unable to resolve problems with your HP Color Copier using information in this User’s Guide, call HP Customer Support. Calling in the U.S.
Maintaining Your HP Color Copier 7 With minimal maintenance you can keep your HP Color Copier in top working condition. Perform the following maintenance procedures as necessary. Cleaning the Exterior Case Use a soft, damp, lint-free cloth to wipe dust, smudges, and stains off the case. The interior of the HP Color Copier does not require cleaning. Keep fluids away from the interior of the HP Color Copier. Cleaning the Glass Dirty copier glass (fingerprints, smudges, etc.
To clean the glass: CAUTION 1 Turn off the HP Color Copier, remove the power cord, and then raise the document cover. 2 Clean the glass with a soft cloth or sponge slightly moistened with warm water and a mild soap or detergent. You may also use glass cleaner. Do not use abrasives, acetone, benzene, or carbon tetrachloride on the glass; these can damage the glass. Do not place liquids directly on the glass. They may seep under it and damage your copier.
Cleaning Cartridges Use the Clean Cartridges feature when the Self Test Page shows streaking or white lines through any of the colored bars. Do not clean cartridges unnecessarily. This wastes ink and shortens the life of your print cartridges. To clean the cartridges: 1 Press the Menu button repeatedly until you see “Clean Cartridges” on the front panel display. 2 Press Select/Resume.
7-4 Maintaining Your HP Color Copier
8 Hewlett-Packard Limited Warranty Model Number: C5370A Product Numbers: 140, 145, 150, and 155 Duration of Limited Warranty (Hardware): 1 Year Duration of Limited Warranty (Print Cartridges): 90 Days Extent of Limited Warranty 1 HP warrants to you, the end-user customer, that HP hardware, accessories and supplies will be free from defects in materials and workmanship after the date of purchase, for the period specified above.
8-2 6 HP MAKES NO OTHER EXPRESS WARRANTY OR CONDITION WHETHER WRITTEN OR ORAL. TO THE EXTENT ALLOWED BY LOCAL LAW, ANY IMPLIED WARRANTY OR CONDITION OF MERCHANTABILITY, SATISFACTORY QUALITY, OR FITNESS FOR A PARTICULAR PURPOSE IS LIMITED TO THE DURATION OF THE EXPRESS WARRANTY SET FORTH ABOVE. Some countries, states or provinces do not allow limitations on the duration of an implied warranty, so the above limitation or exclusion might not apply to you.
Warranty Service Express Service To obtain HP express repair service, the customer must contact an HP service office or an HP Customer Support Center for basic troubleshooting first. If a customer unit needs a minor part replacement and these parts can normally be replaced by the customer, the customer-replaceable components may be serviced through expedited part shipment.
Returning Your HP Color Copier for Service Before You Call Before you call HP Customer Support: 1 Make sure that the copier is plugged in and powered on, that the specified inkjet print cartridges are installed correctly, and that the recommended paper is properly loaded in the input tray. 2 Review the setup section (Chapter 2) and the troubleshooting section (Chapter 5Chapter 5) in this User’s Guide.
Prepare your HP Color Copier for Shipment NOTE 1 Turn on the HP Color Copier, and leave it on for at least 2 minutes. 2 Raise the document cover, and then raise the print cartridge access cover. 3 Remove both print cartridges and close the print cartridge latches. Place print cartridges in an airtight bag so they will not dry out, and put them aside (do not send them with the copier). Print cartridges that remain inside may damage your copier. 4 Attach the orange packing insert (if available).
7 Pack the copier for shipment using the original packing materials. 8 Please also include the following items in the box: A brief description of symptoms for service personnel (samples of print quality problems are helpful). A copy of the sales slip or other proof of purchase to establish the warranty coverage period. Your name, address, and a phone number where you may be reached during the day.
9 Technical Information Speed Specifications All other Reduce/Enlarge Settings: Copy speed is related to the complexity of the document. Margin Black Copy Speed (letter-sized, text) Fast mode: 9 pages per minute Normal mode: 8 pages per minute Color Copy Speed (letter-sized, mixed text and graphics) Fast mode: 3 pages per minute Normal mode: 1 page per minute Color Copy Speed (letter-sized, full page, full-color graphics) Fast mode: 1.7 pages per minute Normal mode: 0.
Black Resolution Fast: 300 x 300 dpi Normal: 600 x 600 dpi Best: 600 x 600 dpi Environmental Specifications Color Resolution Fast: 300 x 300 dpi Normal: 600 x 300 dpi CREt Best: 600 x 600 dpi CREt Recommended ranges 15o–35oC (59o–95oF) Colors Up to 16.
Regulatory Notices FCC Statement (U.S.A.) The United States Federal Communications Commission (in 47 CFR 15.105) has specified that the following notice be brought to the attention of users of this product. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Ordering Accessories and Supplies In the U.S., you may order printer supplies by calling HP Direct, (800) 538-8787, to get the name of your local authorized HP dealer. Outside the U.S. call your local authorized HP dealer. Supplies/Accessories HP Reorder Number Print cartridges Black print cartridge Tri-color print cartridge 51645A C1823A Papers HP Premium InkJet Paper, Letter (200 sheets, 8.5 x 11 in.
index A ADF - see automatic document feeder 5-10 aligning print cartridges 2-10 alignment horizontal 2-10 vertical 2-11 Auto Fit 3-5 does not work properly 5-7 automatic document feeder how to clear a paper jam 3-11, 5-2 image of rollers included on copy 5-10 loading originals 4-4 paper specifications 4-4 tips 3-11 B background color 3-8 Best quality 3-4 black and white copies 3-3 copy speed 9-1 print cartridge 2-7 resolution 9-2 blank page 5-5 boldface, what it means in the user’s guide 1-2 C cancelling
D I damage parts 2-3 dark colors 5-9 darkness, copy 3-6 defaults changing 3-9 factory 3-10 front panel 3-9 indicator 3-9 paper size 2-9 when reset 3-3 inkjet paper 4-1 loading 4-3 inserting print cartridges 2-6 internet 6-1 iron-on transfers loading 4-3 E edges cut off 5-6 ELC (Enhance Light Colors) changing the setting 3-8 enlarging 3-4 Entire 91% 3-4 environmental specifications 9-2 error messages 5-3 F factory defaults 3-10 how to reset 3-10 faded copies 5-6 Fast quality 3-4 front panel attaching ov
changing copy paper size 3-9 heavyweight inkjet 4-1 how to order from HP 4-4 HP papers to use 4-1 inkjet 4-1 iron-on t-shirt transfers 4-2 jams 5-13 loading 2-5 ordering 9-4 output tray capacity 2-5 photo 4-2 recommended types 4-2 settings to use 4-3 size 2-9, 3-9 tips on loading 4-3 to use when copying 4-1 transparencies 4-1 type to use in copier input tray 4-2 types 3-6, 4-3 website location for updates 4-4 paper jam automatic document feeder 5-2 in input tray 5-1 paper type changing 3-6 parts included 2-
power 9-2 speed 9-1 speed specifications 9-1 streaked copies 5-10 support CompuServe 6-2 HP FIRST 6-1 internet 6-1 on-line services 6-1 T text splotchy 5-11 text enhancement 3-7 turning it off 3-8 tip, what this label means in the user’s guide 1-2 torn paper 5-13 transparencies loading 4-4 tips on using 4-4 transparency film 4-1 loading 4-3 troubleshooting 5-1 U unlocking scanner 2-4 unpacking HP Color Copier 2-2 V vertical alignment 2-11 W warning, what this label means in the user’s guide 1-2 warranty
