HP Color LaserJet 2820/2830/2840 Getting Started Guide Guide de mise en route Leitfaden zur Inbetriebnahme Guida introduttiva Guía de instalación inicial Starthandleiding Guia de Introdução Lea esto primero
Copyright Information for you to make the necessary modifications in order to maintain uninterrupted service. If trouble is experienced with this equipment, please see the numbers in the front of this manual for repair and (or) warranty information. If the trouble is causing harm to the telephone network, the telephone company may request you remove the equipment from the network until the problem is resolved.
A HP Color LaserJet 2830 multifunção inclui os mesmos componentes e oferece a mesma funcionalidade que a HP Color LaserJet 2820 multifunção, e também inclui o recurso de fax . Configurazioni della periferica La periferica HP Color LaserJet 2820 All-In-One viene fornita con un vassoio di alimentazione per supporti da 125 fogli, un vassoio di alimentazione per l'ADF da 50 fogli e uno scanner piano. Include inoltre una porta di interfaccia Hi-Speed USB 2.0, un collegamento LAN 10/100 e 96 MB di RAM.
English Français Español Português Italiano Deutsch Nederlands The HP Color LaserJet 2840 all-in-one includes the same components and offers the same functionality as the HP Color LaserJet 2830 all-in-one, and also includes a 250-sheet tray and a memory card reader. Prepare the location Place the device on a sturdy, level surface in a well-ventilated area. Make sure that enough space around the device is available so that the air vents are not blocked.
Regulate the environment Do not place the device in direct sunlight or in an area that has abrupt temperature and humidity changes. The recommended ranges are from 15° to 32.5°C (59° to 90.5°F) and from 10% to 80% relative humidity. Remove the packaging Unbox the printer and remove the package contents. Note Detailed unpacking instructions are on the inside of the top box flap.
Package contents 1) Consumables kit (box with 4 print cartridges); 2) Power cord; 3) Getting started guide and support flyer; 4) Three CDs containing the device software and electronic user guide; 5) Automatic document feeder (ADF) input tray; 6) Imaging drum; AVERTISSEMENT Le périphérique est lourd. Deux personnes sont requises pour le soulever.
) Phone cord (HP Color LaserJet 2830/2840 all-in-one only); 8) HP Color LaserJet all-in-one; 9) Control-panel faceplate (if one is not already installed). Note The USB cable (A/B) is not included.
Play installation CD Insert the installation CD into a CD-ROM. Watch the animated installation guide that is provided on the CD. Note Do not begin installing the software until you have completed step 27 in this getting started guide. 9) Trappe du module de mémoire à deux rangées de connexions (DIMM) ; 10) Port de télécopieur (HP Color LaserJet 2830/2840 allin-one uniquement) ; 11) Port USB 2.
Remove the packing materials 1) Remove all of the orange tape from the printer, except the orange tape that protrudes from the rear output door. 2) Open the rear output door. 3) Pull the two pieces of orange shipping tape that are attached to the fuser shipping locks to remove the shipping locks. 4) Close the rear output door. Note The device will not operate with the shipping locks in place.
English Français Español Português Italiano Deutsch Nederlands Remove the faceplate (optional) 1) Open the scanner-assembly lid. 2) Pull up on the top center of the shipping cover or of the control-panel faceplate that you want to replace. 3) Working outward from the center of the shipping cover or control-panel faceplate, continue to pull up until it releases from the all-in-one.
3) Press the far ends of the faceplate straight down onto the device. Continue to press down while moving your hands toward the center of the faceplate until it snaps into place. Make sure that the faceplate is aligned correctly and has not captured any buttons. 4) Close the scanner assembly lid. The HP Color LaserJet 2820 all-in-one control panel includes the following controls: 1) Alphanumeric buttons; 2) Menu and cancel controls; 3) Copy controls; 4) Scan controls.
Install the ADF input tray 1) Align the two tabs on the input tray with the two grooves in the ADF lid. 2) Slide the tray into the grooves until the tray snaps into place. Le panneau de commande de l'imprimante HP Color LaserJet 2830/2840 all-in-one regroupe les commandes suivantes : 1) Commandes du télécopieur ; 2) Commandes alphanumériques ; 3) Commandes de menu et d'annulation ; 4) Commandes de copie ; 5) Commandes du scanneur et de photos (HP Color LaserJet 2840 uniquement).
Connect a printer cable to the all-in-one Note To use the all-in-one's networking functionality, go to step 13. If you are using the all-in-one as a standalone fax machine or copier, go to step 14. 1) Locate the USB cable port on the back of the device. 2) Connect the USB cable (A/B) to the correct port. Do not connect the cable to a computer or to the network at this time.
English Français Español Português Italiano Deutsch Nederlands Connect a network cable to the device Note If you are not using the networking functionality, go to step 14. 1) Connect a network cable to the network port on the back of the all-in-one. 2) Connect the other end of the cable to an active network port. Connect to a telephone line (HP Color LaserJet 2830/2840 only) Note If you are not using the device fax functionality, go to step 15.
2) Connect the included phone cord to the device line port (the port with the jack. Note Use only the phone cord that came with the device. For more information about faxing, see the "Fax" chapter in the electronic user guide on the device CD (HP Color LaserJet 2830/2840 all-inone only). icon). 3) Connect the phone cord to a live telephone Remarque Utilisez uniquement le cordon téléphonique livré avec le périphérique.
English Français Español Português Italiano Deutsch Nederlands Connect the power cord 1) Connect the power cord to the power socket on the back of the device. 2) Connect the other end of the power cord to a grounded alternating current (AC) outlet. Note Use only the power cord that came with the device. Turn on the device Turn on the device by pressing the power button that is on the side of the device next to the power socket.
Tip: If the device has no power and no lights are illuminated on the control panel, make sure that the power cord is attached securely to both the device and a power outlet. Also, make sure that the power strip is turned on and is operational, or connect the device directly to a wall outlet to test the power strip. Set the control-panel display language and location (if necessary) Note The HP Color LaserJet 2830/2840 control panel is shown. If prompted, select your language and location.
English Français Español Português Italiano Deutsch Nederlands Install the imaging drum 1) Remove the imaging drum from its packaging. 2) Place the imaging drum on a firm surface, and then pull the orange rings to remove the shipping pins. 3) Remove the orange shipping lock on each end of the imaging drum. 4) Remove the two orange shipping spacers. 5) Remove the orange cover from the imaging drum.
6) Press the scanner-release button to open the scanner assembly. 7) Open the top-cover door. 6) Poussez le bouton de verrouillage du scanner pour ouvrir le scanner. 7) Ouvrez le capot supérieur. 6) Pulse el botón de liberación de escáner para abrir el ensamblaje del escáner. 7) Abra la puerta de la cubierta superior. 6) Aperte o botão de liberação do scanner para abrir o conjunto do scanner. 7) Abra a porta da tampa superior. 6) Aprire lo scanner spingendo il relativo pulsante di rilascio.
9) Lower the imaging drum into the printer, slightly rotate the imaging drum toward the front of the printer, and then press it firmly into place. 8) Alignez les flèches vertes situées sur le côté du tambour sur celles qui se trouvent dans l'imprimante. 9) Abaissez le tambour d'imagerie dans l'imprimante, tournez légèrement le tambour vers l'avant de l'imprimante, puis appuyez dessus jusqu'à ce qu'il s'enclenche.
Install the print cartridge 1) Look inside the device and make sure the yellow color carriage of the print-cartridge carousel is open. If Note The print cartridges should be loaded in the device in the same order that they are removed from the print-cartridge kit: Yellow, Magenta, Cyan, and then Black. the yellow color carriage is not open then press (Rotate Carousel) until it is open. (The top door must be closed in order to rotate the carousel.
English Français Español Português Italiano Deutsch Nederlands 2) Remove the print cartridge from its packaging, and then gently shake the cartridge five or six times. 3) Remove the orange cover and pull the sealing tape from the cartridge. 4) Holding the print cartridge with the roller facing you, squeeze the blue release levers. Align the blue arrows on the print cartridge with the blue arrows in the print-cartridge carousel.
5) Close the top-cover door and scanner assembly, and then press 6) Open the scanner assembly and the print-cartridge door, and then repeat steps 2 through 6 for each cartridge color until all four cartridges have been installed. 7) After all cartridges have been (Rotate Carousel). Note Do not press been installed.
English Français Español Português Italiano Deutsch Nederlands CAUTION If toner gets on your clothing, wipe the toner off with a clean cloth, wash the items in cold water, and air dry the items. Using hot water or heat from a dryer sets the toner in the fabric. Note Hewlett-Packard Company cannot recommend using non-HP print cartridges, whether they are new, refilled, or remanufactured. Because they are not HP products, HP cannot influence their design or control their quality.
Setup tray 2 (HP Color LaserJet 2840 all-in-one) 1) Open tray 2, and remove the orange shipping lock inside the tray. 2) Move the blue width guides to match the paper size that is being loaded. 3) Extend the rear of the tray until the arrow points to the size that is being loaded. Installation du bac 2 (HP Color LaserJet 2840 all-in-one) 1) Ouvrez le bac 2, puis retirez le dispositif de sécurité orange se trouvant à l'intérieur du bac.
6) Push down on the paper to lock the metal plate in the tray into place. 7) Slide the tray into the printer. 6) Appuyez sur le papier pour verrouiller la plaque métallique du bac. 7) Faites glisser le bac dans l'imprimante. Français 4) Chargez le papier face à imprimer vers le bas et bord supérieur vers l'avant. Remarque Veillez à ne pas déramer le support avant de le placer dans le bac.
Load tray 1 (Optional if tray 2 is installed) 1) Open tray 1, and then slide out the tray extender. 2) Slide the width guides until they are slightly wider than the paper that you are loading. Chargement du bac 1 (en option si le bac 2 est installé) 1) Ouvrez le bac 1, puis faites glisser l'extension vers l'extérieur. 2) Faites glisser les guides de largeur jusqu'à ce que l'ouverture soit légèrement plus large que le papier que vous chargez.
English Français Español Português Italiano Deutsch Nederlands 3) Load the paper with the side to be printed on face-up, and with the top edge toward the printer. Note Up to 125 pages can be loaded in Tray 1. 4) Slide the width guides in so that they lightly touch the paper. 5) Make sure that the paper fits under the tabs on the width guides. 3) Chargez le papier face à imprimer vers le haut et bord supérieur vers l'imprimante. Remarque Vous pouvez charger jusqu'à 125 pages dans le bac 1.
Print a configuration report Note The HP Color LaserJet 2830/2840 all-in-one control panel is shown. 1) Press the Menu button. 2) Press the press or the button to select Reports, and then (Enter). 3) Press the or the Config report, and then press Impression d'un rapport de configuration Remarque Le panneau de commande de l'imprimante HP Color LaserJet 2830/2840 all-in-one est affiché. 1) Appuyez sur le bouton Menu. (Enter).
Tip: If the copy job produces a blank page, make sure that the original is loaded with the print-side up and that no jams exist in the ADF and paper path. For information about removing jams and other troubleshooting tips, see the electronic user guide on the device CDs. Test du copieur en utilisant le bac d'alimentation BAA 1) Chargez le rapport de configuration que vous venez d'imprimer dans le bac d'alimentation BAA, face imprimée vers le haut.
Self-test the copier by using the flatbed scanner 1) Open the scanner lid, place the configuration report with the print-side down on the flatbed scanner, and then close the scanner lid. 2) Press the Start Color button. Tip: If the copy job produces a blank page, make sure that the original is loaded with the print-side down on the flatbed scanner and that no jams exist in the paper path. For information about removing jams and other troubleshooting tips, see the electronic user guide on the device CD.
English Français Español Português Italiano Deutsch Nederlands Test the memory-card reader Plug an HP-supported memory card into the appropriate slot. The display will indicate that the printer was able to read the memory card. See the "Photo" chapter in the electronic user guide on the device CD for more information about using the memory-card reader.
Complete your device setup If you are using the device as a standalone copier, the setup is complete. If you are using the device as a standalone fax (HP Color LaserJet 2830 all-in-one only), see the "Fax" chapter in the electronic user guide that is provided on the device CD. If you are connecting the device to a network, go to step 27. If you are connecting the device directly to a computer, go to step 28.
English Français Español Português Italiano Deutsch Nederlands If you are using all of the device functionality, see the "Fax" chapter in the electronic user guide that is provided on the device CD (HP Color LaserJet 2830/2840 all-in-one only), and then go to step 27 (Network connection) or step 28 (Installing software) in this getting started guide.
Installing the software Note To install the software for Macintosh, go to step 30. Note You must have administrative privileges to install the software for Windows® XP or Windows 2000. 1) Quit all of the programs that are running on the computer. 2) Follow the instructions that appeared at the end of the animated installation guide on the installation CD. If the installation program does not begin automatically, click Start, click Run, click Browse, select the HPSetup.exe file on the CD, and then click OK.
5) The software prompts you to connect the device to a computer. Connect a USB cable (A/B) from the device to the correct computer port. Note If connecting to a network, proceed to the following step without connecting a USB cable. 3) Sélectionnez Installer le logiciel HP LaserJet. 4) Dans l'Assistant de connexion de l'imprimante, sélectionnez un type de connexion. 5) Le logiciel vous invite à connecter le périphérique à un ordinateur.
6) For Windows 2000 and Windows XP operating systems that meet all system requirements, select Typical, and then follow the instructions to install the software. For Windows 98 and Windows Millennium Edition (Me) operating systems, or any system that does not meet the system requirements, select Minimal, and then follow the instructions to install the software.
1) On the computer, click Start, and then click Programs. 2) Click HP, click HP CLJ 2820/2830/2840, and then click hp Toolbox to open the HP Toolbox. Now, go to step 32. Utilisation du logiciel Boîte à outils HP Remarque Le logiciel Boîte à outils HP n'est pas disponible dans une installation minimale et ne prend pas en charge les systèmes d'exploitation Macintosh. Une fois l'installation du logiciel terminée, vous pouvez utiliser le périphérique à partir de votre ordinateur.
Install the Macintosh software (OS 9.2.2 and later) Note If you are using Macintosh OS X, go to step 31. 1) Connect the USB cable (A/B) to the computer. 2) Quit all of the programs that are running on the computer. 3) Follow the instructions that appeared at the end of the animated installation guide on the device CD. If the installation program did not begin automatically, open the CD folder and double-click the HP All-in-One Installer icon. Installation du logiciel pour Macintosh (OS 9.2.
English Français Español Português Italiano Deutsch Nederlands 4) Follow the onscreen instructions, and then click Install. 5) When prompted, restart the computer. 6) When the HP all-in-one Setup Assistant starts, follow the instructions. Then, go to step 32. Install the Macintosh software (OS X 10.2 and later) 1) Connect the USB cable (A/B) to the computer. 2) Quit all of the programs that are running on the computer. 4) Suivez les instructions qui s'affichent à l'écran, puis cliquez sur Installer.
3) Follow the instructions that appeared at the end of the animated installation guide on the device CD. If the installation program did not begin automatically, open the CD folder and double-click the HP All-in-One Installer icon. 4) Follow the onscreen instructions, and then click Install. 5) When prompted, restart the computer. 6) When the HP All-in-One Setup Assistant starts, follow the instructions.
English Français Español Português Italiano Deutsch Nederlands Test the software installation Print a page from any program to make sure that the software is correctly installed. If the installation failed, reinstall the software. If the reinstallation fails, see the support flyer or go to http://www.hp.com/support/clj2800series for more information.
HP and its subsidiaries respect your privacy and are committed to protecting it. See the HP privacy statement at the Web site. Support information For customer support, see the support flyer or go to http://www.hp.com/support/clj2800series. HP et ses filiales associées respectent votre confidentialité et s'engagent à la protéger. Reportez-vous à la déclaration de confidentialité HP disponible sur le site Web.
English Français Español Português Italiano Deutsch Nederlands Congratulations! The device is ready to use. Open the HP Toolbox, the online support, or the electronic user guide for additional use and troubleshooting information. Félicitations ! Votre périphérique est prêt à être utilisé. Pour obtenir des informations d'utilisation supplémentaires ou des informations de dépannage, ouvrez la Boîte à outils HP, l'assistance en ligne ou la version électronique du Guide de l'utilisateur. Enhorabuena.
44
45
46
© 2004 Hewlett-Packard Development Company, L.P. www.hp.