Insight Integration for HP Network Node Manager Revision 3.4 User Guide
Table Of Contents
- Insight Integration for HP Network Node Manager Revision 3.4 User Guide
- Notice
- Contents
- Introduction
- Installation
- Installation overview
- Preinstallation considerations
- Upgrading from previous versions of the Insight Integration
- Installation procedures for HP-UX and Solaris platforms
- Installation procedures for Windows platforms
- Uninstalling the Insight Integration on HP-UX and Solaris platforms
- Uninstalling the Insight Integration on Windows platforms
- Configuration files
- Tool Definition configuration
- Additional configuration requirements
- Event-only integration
- Installing the Insight Integration on an NNM Remote Console
- Installing the Web Jetadmin integration
- Creating NNM events using HP SIM 5.0
- Creating NNM events using HP SIM 5.1
- Configuring SNMP on an HP ProLiant server running NNM
- Using the software
- Using the Insight Integration
- Discovering HP servers with the Insight Integration
- Insight Integration menus
- Insight Integration menu options
- Viewing HP systems information
- HP event management in HP Network Node Manager
- HP Insight Information menu options
- HP Insight Summary Launch for desktops
- HP Insight Information for servers
- Summary
- Integrated Management Log
- Software Version
- System—Processor
- System—Memory
- System—PCI slots
- Health—Fault-tolerant fans
- Health—Temperatures
- Health—Thresholds
- Drives—SCSI
- Drives—IDA
- Drives—Fibre
- Insight Lights-Out information
- Insight Lights-Out log
- HP Insight graphics
- HP Insight rack information
- Using HP Systems Insight Manager with HP Network Node Manager
- Configuring the HP Systems Insight Manager launch on Windows
- Configuring the Systems Insight Manager launch on UNIX
- Launching HP Systems Insight Manager
- Running an in-context launch to HP Systems Insight Manager
- Using the Insight Integration with the Dynamic Views interface
- Using the Insight Integration with the NNM web interface
- Using the Insight Integration with HP Web Jetadmin
- Viewing events in HP Systems Insight Manager
- Using the Insight Integration with the NNM Remote Console
- Troubleshooting
- Technical support
- Acronyms and abbreviations
- Index
Troubleshooting 98
• CPQCHKCONF checks the syntax of CPQCONFIG.DAT.
• CPQCHKTCONF checks the syntax of CPQTRAPD.CONF.
• CPQCHKSTR checks the syntax of CPQVAL2STR.TRAP and CPQVAL2STR.INFO.
• CPQCHKNODE checks the syntax of CPQNODE.DAT.
• CPQCHKAUTH displays the authorization details of the HP integration.
Checking the status of background processes
To confirm that the Insight Integration background processes are active, run the OVSTATUS command
from a command line prompt.
The Insight Integration uses two background processes that provide discovery of HP nodes on the NNM
management map and translate HP SNMP events on the NNM Event Browser:
• CPQDIS
• CPQTRAP
If either of these processes are not displayed as active, configuration or communication problems might
exist. For information about confirming that the Insight Integration is installed correctly, see "Validating the
configuration (on page 97)." For more information, see the HP Network Node Manager User's Guide.
Normally, the process management daemon OVSPMD starts these processes when the operating system
is initialized. If any of these background processes are not running, before initializing the OVW, start
them by entering the OVSTART command. For more information, see the HP Network Node Manager
User's Guide.
Additional resources
The following additional resources are available:
• Frequently asked questions
(http://h18000.www1.hp.com/products/servers/management/openview/questionsanswers.html
)
• HP Management Integration Support website
(http://h18013.www1.hp.com/products/servers/management/integration.html?jumpid=reg_R100
2_USEN)
• HP OpenView user documentation
(ftp://ftp.compaq.com/pub/products/servers/management/HPInsightNNM33.pdf
)