HP Designjet 4000- en 4500-printerserie De printer gebruiken
Wettelijke kennisgevingen Handelsmerken De informatie in deze handleiding kan zonder voorafgaande kennisgeving worden gewijzigd. Adobe®, Acrobat®, Adobe Photoshop® en PostScript® zijn handelsmerken van Adobe Systems Incorporated. Hewlett-Packard geeft geen enkele garantie, daaronder mede begrepen maar niet beperkt tot impliciete garanties van verkoopbaarheid en geschiktheid voor een bepaalde toepassing.
Inhoudsopgave 1 Inleiding Deze handleiding....................................................................................................................................2 Inleiding.................................................................................................................................2 Hoe........................................................................................................................................2 Het probleem is.......................................
Geheugenuitbreidingskaart..................................................................................................48 3 Hoe... (onderwerpen over printermontage) [4500] Aan de slag..........................................................................................................................................50 De printer uitpakken.............................................................................................................................50 De voet in elkaar zetten............
De instelling voor de slaapstand wijzigen...........................................................................................114 De zoemer uitzetten...........................................................................................................................115 Het contrast van het voorpaneel wijzigen...........................................................................................115 Een andere maateenheid selecteren..............................................................
De stapelaar verwijderen....................................................................................................................150 De temperatuur wijzigen.....................................................................................................................151 Rollen papier vervangen bij gebruik van de stapelaar.......................................................................151 De buitenkant van de stapelaar reinigen..........................................................
Printerinstellingen..............................................................................................................182 Nauwkeurige kleuren genereren met QuarkXPress 6........................................................................182 Toepassingsinstellingen....................................................................................................183 Stuurprogramma-instellingen.............................................................................................
Horizontale strepen over stroken van één enkele kleur.....................................................231 Oplossing...........................................................................................................................231 Horizontale strepen over alle gekleurde stroken...............................................................232 Oplossing...........................................................................................................................
Het lukt niet om het papier te laden [4500].........................................................................................261 Een papierstoring (papier zit vast in printer) [4000]............................................................................262 Controleer het printkoppad................................................................................................262 Papierpad controleren................................................................................................
De afbeelding bevindt zich slechts in één gedeelte van het afdrukgebied ........................................299 De afbeelding is onverwacht geroteerd..............................................................................................299 De afdruk is een spiegelbeeld van het origineel ................................................................................299 De afdruk is vervormd of onleesbaar..............................................................................................
De toepassing wordt trager of loopt vast tijdens het genereren van de afdruktaak...........................319 Een communicatiestoring tussen de computer en printer..................................................................320 De browser heeft geen toegang tot de geïntegreerde webserver......................................................320 Een fout vanwege onvoldoende geheugen........................................................................................
Papier bestellen..................................................................................................................................356 Accessoires bestellen.........................................................................................................................359 31 Vertel me over... (Help-onderwerpen opvragen) HP Instant Support.............................................................................................................................362 HP Customer Care....
1 NLWW Inleiding ● Deze handleiding ● Basisfuncties van de printer ● Basisonderdelen van de printer [4000] ● Basisonderdelen van de printer [4500] ● Voorpaneel ● Printersoftware ● Scannersoftware [4500] 1
Deze handleiding De printer gebruiken (op cd) en de referentiehandleiding (papieren versie) zijn ingedeeld in de volgende hoofdstukken. Inleiding Dit hoofdstuk bevat een korte inleiding tot de printer en de documentatie bij de printer voor nieuwe gebruikers. Hoe... Deze hoofdstukken helpen u verschillende procedures uit te voeren, zoals het laden van papier of het vervangen van een inktpatroon.
Opmerking De HP Designjet 4500-serie ondersteunt papierrollen met een maximumlengte van 175 m (575 ft). ● Productiviteitsverhogende functies, zoals het verzenden van afdruktaken die uit meerdere bestanden bestaan, het vooraf bekijken van taken, wachtrijen en nesten via de geïntegreerde webserver van de printer (zie Vertel me over...
3. Printkopwagen 4. Printkop 5. Printkopreiniger 6. Voorpaneel 7. As 8. Verwijderbare blauwe papierstop 9. Opvangbak 10. Inktpatroonlade 11. Ashendel 12. Papierladingshendel Achteraanzicht 1. Houder voor referentiehandleiding 2. Aansluiting netsnoer en aan/uit-toets 3. Aansluitingen voor communicatiekabels en optionele accessoires Basisonderdelen van de printer [4500] Opmerking 4 Hoofdstuk 1 Inleiding Dit onderwerp is alleen van toepassing op de HP Designjet 4500-printerserie.
De basisonderdelen worden weergegeven op het volgende voor- en achteraanzicht van de printer. Vooraanzicht 1. Inktpatronen 2. Plaat 3. Printkopwagen 4. Printkop 5. Printkopreiniger 6. Voorpaneel 7. Papierladingshendel (rol 1) 8. As 9. Papierladingshendel (rol 2) 10.
11. Aslade (rol 1) 12.
Achteraanzicht 1. Houder voor referentiehandleiding 2. Aansluiting netsnoer en aan/uit-toets 3. Aansluitingen voor communicatiekabels en optionele accessoires Voorpaneel Het voorpaneel van de printer bevindt zich rechts vooraan op de printer. Dit paneel heeft de volgende belangrijke functies: NLWW ● Het moet worden gebruikt voor bepaalde handelingen, zoals het laden of verwijderen van papier.
Het voorpaneel bestaat uit de volgende onderdelen: 1. Het weergavegebied voor informatie, pictogrammen en menu's. 2. Met de aan/uit-toets zet u de printer aan en uit. Als de printer in de slaapstand staat, activeert u de printer weer met deze toets. 3. Het aan/uit-lampje brandt niet wanneer de printer is uitgeschakeld. Het is oranje wanneer de printer in de slaapstand staat. Het is groen wanneer de printer is ingeschakeld. Het is groen en knippert wanneer de printer wordt geïnitialiseerd. 4.
Als u een item op het voorpaneel wilt selecteren, markeert u het item en drukt u op de toets Selecteren. De vier pictogrammen op het voorpaneel bevinden zich in het hoofdmenu. Als u een pictogram wilt selecteren of markeren maar u de pictogrammen niet op het voorpaneel ziet, drukt u op de toets Vorige tot u de pictogrammen ziet.
Het voorbeeldvenster vult het grootste gedeelte van de weergavesectie. Daarboven bevindt zich de werkbalk voor afbeeldingen, met negen knoppen waarmee u het voorbeeld kunt wijzigen (zie Scanvoorbeelden weergeven). De controlesectie bevat vier tabbladen: Copy (Kopiëren), Scan (Scannen), Print (Afdrukken) en Setup. Elk tabblad bevat opties die u kunt instellen bij het kopiëren, scannen, afdrukken of configureren. Onder aan de pagina bevinden zich zeven grotere knoppen. Van links naar rechts: 10 1.
2 Hoe... (onderwerpen over printermontage) [4000] Opmerking NLWW Dit hoofdstuk is alleen van toepassing op de HP Designjet 4000-printerserie.
Aan de slag In de volgende onderwerpen wordt besproken hoe u de nieuwe printer in elkaar zet (zie ook de setupinstructies). Aangezien sommige onderdelen van de printer groot zijn, zijn mogelijk maximaal vier personen nodig om ze op te tillen. U hebt ook een vloeroppervlak van ten minste 3 x 5 m (10 x 16 ft) nodig. Het in elkaar zetten duurt ongeveer twee uur. De symbolen op de dozen geven de inhoud aan.
Wanneer u een geschikte locatie hebt gevonden, kunt u de printer uitpakken. NLWW 1. Verwijder de twee zijpanelen. Verwijder vervolgens de bovenste kunststof handgrepen aan beide zijkanten van de doos (twee aan elke kant, vier in totaal). 2. Knip de band om de dozen los maar ga hierbij voorzichtig te werk, omdat de dozen kunnen vallen zodra u de band hebt losgeknipt. 3. Verwijder de dozen aan de bovenkant van de hoofdprinterdoos. 4.
5. Verwijder de hoofdprinterdoos. 6. Verwijder de twee verpakkingsstukken. De voet in elkaar zetten WAARSCHUWING Bij het uitpakken van de voet zult u merken dat twee wieltjes van de voet zijn voorzien van antislipmateriaal. Verwijder dit materiaal nu nog niet. 14 1. Haal de eerste module uit de doos met de voet en de bak. 2. Haal uit de eerste module de twee dozen met een L en een R. Leg ze op de vloer zoals in de illustratie wordt aangegeven. Hoofdstuk 2 Hoe...
3. Leg de dwarsbeugel op de L- en R-dozen. 4. Nu moet u de linker- en rechterkant van de dwarsbeugel identificeren. (1) links (2) rechts (3) één opening (4) twee openingen NLWW 5. Pak nu het zakje met schroeven en de schroevendraaier die bij de printer zijn geleverd. De schroevendraaier is enigszins magnetisch. 6. Verwijder de twee afdekplaten van de linkersteun.
7. Plaats de linkersteun op het linkeruiteinde van de dwarsbeugel. De linkersteun past alleen op het linkeruiteinde van de dwarsbeugel. 8. Bevestig de linkersteun op de dwarsbeugel met behulp van vier schroeven aan de binnenkant van de steun. 9. Bevestig de linkersteun op de dwarsbeugel met behulp van twee schroeven aan de buitenkant van de steun. 10. Plaats de rechtersteun op het rechteruiteinde van de dwarsbeugel. De rechtersteun past alleen op het rechteruiteinde van de dwarsbeugel.
11. Bevestig de rechtersteun op de dwarsbeugel met behulp van vier schroeven aan de binnenkant van de steun. 12. Bevestig de rechtersteun op de dwarsbeugel met behulp van twee schroeven aan de buitenkant van de steun. 13. Plaats een rolsteun op de linkersteun. Er zijn pinnen om u te helpen bij het juist positioneren van de rolsteun. Opmerking Verwijder het antislipmateriaal niet van het wieltje. 14. Zet de linkerrolsteun vast met vier schroeven.
15. Plaats een rolsteun op de rechtersteun. Er zijn pinnen om u te helpen bij het juist positioneren van de rolsteun. Opmerking Verwijder het antislipmateriaal niet van het wieltje. 16. Zet de rechterrolsteun vast met vier schroeven. De voet bevestigen 1. U moet nu de linker- en rechterkant van de printer identificeren. Deze informatie staat op de piepschuimverpakking. Identificeer ook de achterkant van de printer. 2. Trek de beschermhoes open vanaf de voet van de printer.
3. In deze stap plaatst u de pinnen van de voet in de openingen in het midden van de printerbeugels. Plaats de voet op de printer met het antislipmateriaal naar de achterkant van de printer gericht. NLWW 4. Gebruik één schroef om de rechterkant van de voet op de printer te bevestigen. Draai de schroef goed aan. 5. Gebruik twee schroeven om de linkerkant van de voet op de printer te bevestigen. Draai de schroeven goed aan.
6. Leg de dozen met reserveonderdelen en verbruiksartikelen tegen de achterkant van de printerdoos. De pijlen op de dozen moeten naar de printerdoos wijzen. Controleer of het antislipmateriaal zich nog op de twee achterste wieltjes bevindt. 7. Draai de printer met vier personen op de dozen met reserveonderdelen en verbruiksartikelen. Draai de printer tot de achterkant op de dozen met reserveonderdelen en verbruiksartikelen rust, en de wieltjes met het antislipmateriaal de vloer raken. 8.
9. Laat vier personen de handgrepen aan de achterkant van de printer beetpakken en kantel de printer voorzichtig rechtop. Het antislipmateriaal voorkomt dat de printer naar voren schuift. Verpakkingsmateriaal verwijderen NLWW 1. Verwijder de twee piepschuimverpakkingen en de beschermhoes van de printer. 2. Plaats de afdekplaat op de voorkant van de linkersteun (1) en klik de achterrand (2) vast.
22 3. Plaats de afdekplaat op de voorkant van de rechtersteun (1) en klik de achterrand (2) vast. 4. Verwijder het antislipmateriaal van de twee achterwieltjes op de voet. 5. Verwijder de verpakkingstape 1 tot en met 8. Open het printervenster en verwijder de twee vensterblokjes 9 en 10. 6. Verwijder de beschermfilm van het printervenster en het voorpaneelscherm. 7. Verwijder de asvergrendeling. Hoofdstuk 2 Hoe...
8. Open de deur van de printkopreiniger en verwijder het verpakkingsmateriaal van de wagen. Sluit de deur van de reiniger. 9. Druk de ashendel omlaag om het rechteruiteinde van de as los te maken. Verwijder eerst dat uiteinde van de as en vervolgens het linkeruiteinde. Plaats uw vingers niet in de assteunen tijdens het verwijderen. 10. Verwijder het piepschuimstuk van de asvergrendeling en zet de as terug. 11. Installeer de houder voor de referentiehandleiding.
De bak in elkaar zetten 24 1. Zoek de onderdelen van de bak bij elkaar. 2. Plaats één schroef in de binnenkant van de linkersteun van de voet. 3. Draai de schroef nog niet aan. 4. Plaats één schroef in de binnenkant van de rechtersteun van de voet. 5. Draai de schroef nog niet aan. Hoofdstuk 2 Hoe...
6. Til het ondersteunende frame van de bak naar de juiste plaats aan de voorkant van de printer. 7. Plaats de bovenarmen van de bak op de twee schroeven die u in de vorige stap hebt aangebracht. 8. Gebruik één schroef per steun om de onderarmen van de bak op de voet te bevestigen. 9. Draai nu de bovenste twee schroeven aan. 10. Klik de zes lussen op het frame van de bak. Plaats hierbij de lussen met uitbreiding achteraan in stand 2, 4 en 6.
11. Gebruik twee klemmen per lus om de zes lussen vast te zetten op het frame. 12. Bevestig de drie verplaatsbare stoppers op de drie lussen, zoals is aangegeven in de figuur. 13. Druk de verplaatsbare stopper voorzichtig in en bevestig deze op de lus. 14. Wanneer de verplaatsbare stopper vastzit op de lus, laat u de stopper los. 15. Zet de drie verplaatsbare stoppers in de ingeklapte stand.
De printer de eerste keer aanzetten NLWW 1. Sluit het netsnoer op de achterkant van de printer aan en steek het andere uiteinde in een stopcontact. 2. Zet de aan/uit-schakelaar aan de achterkant van de printer in de stand Aan. 3. Als het aan/uit-lampje op het voorpaneel niet gaat branden, drukt u op de aan/uit-toets om de printer aan te zetten. 4. Wacht tot dit voorpaneelbericht verschijnt. Markeer uw taal op het voorpaneel met behulp van de toetsen Omhoog en Omlaag. Druk op de toets Selecteren.
5. Het voorpaneel geeft nu aan hoe u de inktpatronen installeert. Inktpatronen installeren 28 1. Haal de printkoppen, printkopreinigers en inktpatronen uit de doos met verbruiksartikelen. 2. Zoek de inktpatroondeur aan de linkerkant van de printer. 3. Druk op de deur tot u een klik hoort. 4. Open de inktpatroondeur. Hoofdstuk 2 Hoe...
5. Trek de blauwe hendel omlaag om de inktpatroonlade te ontgrendelen. 6. Schuif de inktpatroonlade naar buiten. 7. Plaats de inktpatroon op de lade. Opmerking Merktekens op de lade geven de juiste locatie aan. 8. NLWW Zet de inktpatroon aan de achterkant van de lade, zoals is aangegeven in de figuur.
9. Duw de inktpatroonlade weer in de printer tot deze vastklikt. Als u problemen ondervindt, gaat u naar Ik kan geen inktpatroon plaatsen. 10. Installeer de overige drie inktpatronen op dezelfde manier. 11. Sluit de inktpatroondeur (druk op de deur tot deze vastklikt). 12. Wacht ongeveer een minuut tot dit voorpaneelbericht verschijnt. 30 Hoofdstuk 2 Hoe...
De installatiekoppen verwijderen NLWW 1. Open het printervenster. 2. Verwijder de verpakkingstape waarmee de vergrendeling van de printkopwagen is vastgezet. 3. Trek de vergrendeling aan de bovenkant van de wagen omhoog en laat weer los. 4. Til de afdekplaat omhoog. Hierdoor krijgt u toegang tot de installatiekoppen.
32 5. Voordat u de installatiekoppen verwijdert, kijkt u via het venster aan de bovenkant van elke kop of de kop inkt bevat. Als dat niet het geval is, neemt u contact op met de klantenondersteuning. 6. Zet de blauwe hendel omhoog om een installatiekop te verwijderen. 7. Gebruik de blauwe hendel om de installatiekop voorzichtig uit de wagen te halen. 8. Til de installatiekop omhoog tot deze loskomt uit de wagen. Verwijder vervolgens de overige installatiekoppen. Hoofdstuk 2 Hoe...
De printkoppen installeren 1. Verwijder de blauwe beschermkap en de transparante beschermtape van de printkop. 2. Laat alle printkoppen verticaal in de juiste positie zakken. 3. Installeer de printkoppen traag en voorzichtig. Als u problemen ondervindt, gaat u naar Ik kan geen printkop plaatsen. NLWW 4. Controleer of de printkoppen goed vastzitten.
6. Sluit de afdekplaat van de wagen. 7. Controleer of de vergrendeling goed vastklikt. 8. Sluit het printervenster. 9. Wacht ongeveer een minuut tot de printer de printkoppen heeft gecontroleerd. De printkopreinigers installeren 1. 34 Wacht tot dit voorpaneelbericht verschijnt. Hoofdstuk 2 Hoe...
2. Druk op de deur van de printkopreinigers aan de rechterkant van de printer. 3. Open de deur van de printkopreinigers. 4. Plaats de printkopreiniger in de juiste sleuf (afhankelijk van de kleur). 5. Duw de printkopreiniger naar binnen en omlaag tot deze vastklikt. Als u problemen ondervindt, gaat u naar Ik kan geen printkopreiniger plaatsen.
6. Plaats de overige zeven printkopreinigers in de juiste sleuven. 7. Sluit de deur van de printkopreinigers. 8. Wacht tot dit voorpaneelbericht verschijnt en druk vervolgens op de toets Selecteren. Een rol papier op de as plaatsen 1. 36 Zet de ashendel omlaag. Hoofdstuk 2 Hoe...
2. Haal het rechteruiteinde van de as (1) uit de printer en trek de as naar rechts om het andere uiteinde (2) te kunnen verwijderen. Plaats uw vingers niet in de assteunen tijdens het verwijderen. 3. Verwijder de blauwe papierstop (1) aan het linkeruiteinde van de as. Houd de as horizontaal. 4. Schuif de papierrol die bij de printer is geleverd, op de as. Zorg dat u het papier exact zoals in de figuur houdt. Opmerking Ook op de as wordt de juiste richting aangegeven. 5.
38 6. Controleer of de stop goed is geplaatst. 7. Schuif de as met de blauwe papierstop aan de linkerkant in de printer. De ashendel komt automatisch omlaag wanneer u de as plaatst. 8. Als u weerstand voelt, zet u de ashendel omhoog om de as goed te plaatsen. 9. Als de as goed is geplaatst, staat de ashendel horizontaal. Hoofdstuk 2 Hoe...
Papier in de printer laden NLWW 1. Markeer op het voorpaneel het pictogram 2. Markeer Paper load (Papier laden) en druk op de toets Selecteren. 3. Markeer Load roll (Rol laden) en druk op de toets Selecteren. 4. Markeer het type papier dat u hebt geladen en druk op de toets Selecteren. 5. Wacht tot het bericht 'Open window' (Open venster) verschijnt. en druk op de toets Selecteren.
6. Open het printervenster. 7. Zet de papierladingshendel omhoog. 8. Trek ongeveer één meter (3 ft) van de rol. 9. Plaats de rand van de papierrol boven de zwarte rol. WAARSCHUWING Zorg dat u bij het laden van papier de rubberen wieltjes van de plaat niet aanraakt, omdat deze wieltjes kunnen gaan draaien en huid, haar of kleding hierin kunnen komen vast te zitten. 40 Hoofdstuk 2 Hoe...
10. Wacht tot het papier uit de printer wordt gevoerd, zoals hieronder is afgebeeld. Opmerking Als u bij het laden van papier onverwachte problemen ondervindt, gaat u naar Het lukt niet om het papier te laden [4000]. 11. Zorg dat het papier is uitgelijnd met de blauwe lijn en de halve cirkel op de plaat. 12. Zet de papierladingshendel omlaag. 13. Normaal gesproken verschijnt het volgende voorpaneelbericht.
14. Gebruik de stops om het overtollige papier voorzichtig terug te draaien op de as. 15. Sluit het printervenster. 16. De printer stelt het papier af door naar voren en naar achteren te rollen. Vervolgens verschijnt het volgende voorpaneelbericht. 17. Gebruik de stops om het overtollige papier voorzichtig terug te draaien op de as. 18. De printer voert automatisch uitlijning van de printkoppen en kleurkalibratie uit voor het papiertype dat u hebt geladen.
De printer aansluiten 1. Uw printer kan direct op een computer of via een netwerk op een of meer computers worden aangesloten. (1) Pc, Macintosh of werkstation (2) Printer (3) Server (4) Pc, Macintosh of werkstation NLWW 2. Zoek de computer- of netwerkaansluiting aan de achterkant van de printer of installeer een optioneel accessoire. 3. De printer is voorzien van een Fast-Ethernet-aansluiting voor een netwerkverbinding.
4. Voor directe verbinding met computers zijn twee FireWire-aansluitingen aangebracht. Een van deze aansluitingen kan ook worden gebruikt om de HP Designjet 4500-scanner aan te sluiten. Opmerking Er wordt geen FireWire-kabel bij de printer geleverd. U kunt een willekeurige kabel gebruiken die wordt aanbevolen door de 1394 Trade Association. 5. Voor aansluiting van een optioneel accessoire beschikt de printer over een grotere connector.
Het voorpaneel geeft de status van de aansluiting aan met het bericht Installed (Geïnstalleerd) of Not installed (Niet geïnstalleerd). Voer de juiste instructies uit om de printer op het netwerk aan te sluiten: ● Aansluiten op een netwerk (Windows) ● Aansluiten op een netwerk (Mac OS X) ● Aansluiten op een netwerk (Mac OS 9) [4000] U kunt de netwerkkabel aansluiten zoals hieronder wordt aangegeven. USB 2.0-aansluiting Als u wilt controleren of de USB 2.
U kunt de USB-kabel aansluiten zoals hieronder wordt aangegeven. Jetdirect-printserver Zo installeert u de Jetdirect-kaart: 1. 46 Verwijder de kleine afdekplaat aan de achterkant van de printer door de twee schroeven bij de linkerkant los te draaien. Hoofdstuk 2 Hoe...
2. Plaats de Jetdirect-kaart en zet deze vast met de schroeven die bij de kaart worden geleverd. 3. Bewaar de afdekplaat en de schroeven voor het geval u de Jetdirect-kaart later weer wilt verwijderen. op het voorpaneel Als u wilt controleren of de kaart correct is geïnstalleerd, selecteert u het pictogram en selecteert u I/O setup (I/O-configuratie) > Jetdirect EIO > View information (Informatie weergeven).
Geheugenuitbreidingskaart Als u wilt controleren of de geheugenuitbreidingskaart van 256 MB correct is geïnstalleerd, selecteert u het pictogram op het voorpaneel en selecteert u View printer information (Printerinformatie weergeven). Op het voorpaneel verschijnen verschillende gegevens over de printer, zoals het geheugen. Als de geheugengrootte 512 MB wordt weergegeven, is de geheugenuitbreidingskaart correct geïnstalleerd. 48 Hoofdstuk 2 Hoe...
3 Hoe... (onderwerpen over printermontage) [4500] Opmerking NLWW Dit hoofdstuk is alleen van toepassing op de HP Designjet 4500-printerserie.
Aan de slag In de volgende onderwerpen wordt besproken hoe u de nieuwe printer in elkaar zet (zie ook het document Printer assembly (Printermontage)). Aangezien sommige onderdelen van de printer groot zijn, zijn mogelijk maximaal vier personen nodig om ze op te tillen. U hebt ook een vloeroppervlak van ten minste 3 x 5 m (10 x 16 ft) nodig. Het in elkaar zetten duurt ongeveer vier uur.
3. De symbolen op de dozen geven de inhoud aan. Raadpleeg de volgende tabel: Symbool op doos Inhoud van doos Printer Voet en bakmodule Doos met verbruiksartikelen, zoals...
52 4. Verwijder de twee panelen. Plaats de dozen met verbruiksartikelen en reserveonderdelen aan de voorkant van de printer. Plaats de doos met de voet en de bak op de dozen met verbruiksartikelen en reserveonderdelen. Zet de doos vervolgens op de vloer. 5. Plaats de doos met de rolmodule op de dozen met verbruiksartikelen en reserveonderdelen. Zet de doos met de rolmodule op de vloer. Verwijder vervolgens de dozen met verbruiksartikelen en reserveonderdelen. 6.
7. Verwijder de hoofdprinterdoos. 8. Verwijder de twee verpakkingsstukken. De voet in elkaar zetten 1. NLWW Haal de eerste module met de onderdelen voor de bak uit de doos.
54 2. Haal de tweede module uit de doos met de voet en de bak. Deze module bevat de voetsteunen. 3. Haal uit de module de twee dozen met een L en een R. Leg ze op de vloer zoals in de illustratie wordt aangegeven. 4. Leg de dwarsbeugel op de L- en R-dozen. 5. Nu moet u de linker- en rechterkant van de dwarsbeugel identificeren. De linkerkant (1) heeft twee openingen en de rechterkant (2) heeft één opening, zoals in de illustratie wordt getoond. Hoofdstuk 3 Hoe...
NLWW 6. Pak het zakje met schroeven en de schroevendraaier die bij de printer zijn geleverd. De schroevendraaier is enigszins magnetisch. 7. Identificeer de linkersteun (A), zoals in de illustratie wordt getoond. Verwijder de twee afdekplaten van de linkersteun. 8. Plaats de linkersteun op het linkeruiteinde van de dwarsbeugel. De linkersteun past alleen op het linkeruiteinde van de dwarsbeugel. 9.
10. Bevestig de linkersteun op de dwarsbeugel met behulp van twee schroeven aan de buitenkant van de steun. 11. Plaats de rechtersteun op het rechteruiteinde van de dwarsbeugel. De rechtersteun past alleen op het rechteruiteinde van de dwarsbeugel. 12. Bevestig de rechtersteun op de dwarsbeugel met behulp van vier schroeven aan de binnenkant van de steun. 13. Bevestig de rechtersteun op de dwarsbeugel met behulp van twee schroeven aan de buitenkant van de steun. 56 Hoofdstuk 3 Hoe...
14. Bevestig de dwarsbeugel van de voet met behulp van vier schroeven. 15. Plaats een rolsteun op de linkersteun. Er zijn pinnen om u te helpen bij het juist positioneren van de rolsteun. WAARSCHUWING Verwijder het antislipmateriaal niet van het wieltje. 16. Zet de linkerrolsteun vast met vier schroeven. 17. Plaats een rolsteun op de rechtersteun. Er zijn pinnen om u te helpen bij het juist positioneren van de rolsteun. WAARSCHUWING Verwijder het antislipmateriaal niet van het wieltje.
18. Zet de rechterrolsteun vast met vier schroeven. 19. Zet de voet rechtop, zoals in de illustratie wordt getoond 20. Open de doos met de rolmodule. Verwijder de kunststof doos met de schroeven. 21. Identificeer de gekleurde pluggen op de steunen. 58 Hoofdstuk 3 Hoe...
22. Verwijder de blauwe plug op de linkersteun. 23. Plaats de pin in de linkersteun. 24. Verwijder de blauwe plug op de rechtersteun.
25. Plaats de pin in de rechtersteun. 26. Verwijder de bovenste gele plug op de linkersteun. 27. Plaats de pin aan de binnenkant van de linkersteun. 60 Hoofdstuk 3 Hoe...
28. Verwijder de bovenste gele plug op de rechtersteun. 29. Plaats de pin aan de binnenkant van de rechtersteun. De voet bevestigen NLWW 1. Identificeer de linker- en rechterkant van de printer. Deze informatie staat op de piepschuimverpakking. Identificeer ook de achterkant van de printer. 2. Trek de beschermhoes open vanaf de voet van de printer. Zorg voor een vrije ruimte van drie meter aan de achterkant van de printer en één meter aan de voorkant van de printer.
62 3. Verwijder met de meegeleverde schroevendraaier de twee schroeven die lade 1 op zijn plaats houden. 4. Schuif lade 1 naar buiten totdat de lade de piepschuimverpakking raakt. 5. Plaats de voet ondersteboven op de printer. Zorg dat u de pinnen van de voet in de openingen in het midden van de printerbeugels plaatst. Het antislipmateriaal moet naar de achterkant van de printer zijn gericht. Hoofdstuk 3 Hoe...
6. Gebruik één schroef om de rechterkant van de voet op de printer te bevestigen. Draai de schroef goed aan. 7. Schuif lade 1 naar voren om de voorste schroef beter te kunnen plaatsen. Gebruik twee schroeven om de linkerkant van de voet op de printer te bevestigen. Draai de schroeven goed aan. De rolmodule bevestigen Let er bij het uitpakken van de rolmodule op dat u dit onderdeel alleen vastpakt bij de punten die worden aangegeven door de groene pijlen.
64 1. Open de doos met de rolmodule en verwijder de twee piepschuimstukken. 2. Haal de rolmodule uit de doos. 3. Verwijder de rolmodule uit de kunststof zak. Hoofdstuk 3 Hoe...
4. Verwijder de twee resterende gele pluggen uit de linker- en rechtersteunen. Onthoud de positie van deze openingen. 5. Draai de rolmodule ondersteboven, zoals in de illustratie wordt getoond. Draag de rolmodule vervolgens naar de voorkant van de omgekeerde printer. 6. Leg de rolmodule naast de eerste dwarsbeugel van de printer. 1. De achterkant van de printer.
66 7. Let erop voordat u de rolmodule op zijn plaats schuift, dat de rolmodule op de pinnen rust die u eerder op de voetsteunen hebt geplaatst. 8. Til de rolmodule met twee personen op, waarbij een derde persoon aan de achterkant van de printer staat. Schuif de rolmodule op de pinnen die u eerder op de voetsteunen hebt geplaatst. 9. Zorg dat de rolmodule tegen de voetsteunen rust, vanaf de voorkant gezien. Hoofdstuk 3 Hoe...
10. Bevestig de rolmodule aan de rechtersteun van de voet. 11. Bevestig de rolmodule aan de linkersteun van de voet. 12. Zet de rolmodule aan de rechtersteun van de voet vast met twee extra schroeven.
13. Zet de rolmodule aan de linkersteun van de voet vast met twee kraagschroeven. De printer opstellen 68 1. Leg de dozen met reserveonderdelen en verbruiksartikelen tegen de achterkant van de printerdoos. De pijlen op de dozen moeten naar de printerdoos wijzen. Controleer of het antislipmateriaal zich nog op de twee achterste wieltjes bevindt. 2. Draai de printer met vier personen op de dozen met reserveonderdelen en verbruiksartikelen. Hoofdstuk 3 Hoe...
NLWW 3. Draai de printer tot de achterkant op de dozen met reserveonderdelen en verbruiksartikelen rust, en de wieltjes met het antislipmateriaal de vloer raken. 4. Verwijder de pallet voordat u de printer rechtop probeert te kantelen. 5. Laat vier personen de handgrepen aan de achterkant van de printer beetpakken en kantel de printer voorzichtig rechtop. 6. Zet de printer rechtop. Het antislipmateriaal voorkomt dat de printer naar voren schuift.
7. Verwijder de twee piepschuimverpakkingen en de beschermhoes van de printer. 8. Plaats de afdekplaat op de voorkant van de linkersteun (1) en klik de achterrand (2) vast. 9. Plaats de afdekplaat op de voorkant van de rechtersteun (1) en klik de achterrand (2) vast. 10. Verwijder het antislipmateriaal van de twee achterwieltjes op de voet. 70 Hoofdstuk 3 Hoe...
11. Verwijder verpakkingstape 1 tot en met 12. 12. Open het printervenster. Verwijder vervolgens de twee vensterblokjes en het verpakkingsmateriaal van de inktrol. 13. Verwijder de beschermfilm van het printervenster en het voorpaneelscherm. 14. Open de deur van de printkopreiniger en verwijder het verpakkingsmateriaal van de wagen. Sluit de deur van de reiniger.
15. Installeer de houder voor de referentiehandleiding. Houd de houder bovenaan in een hoek (1), plaats de twee haken in de openingen en klik het onderste gedeelte (2) vast op de achterkant van de printer. 16. Verwijder de twee gele kunststof schroeven aan de rechter- en linkerkant van de papierinvoer. 17. Verwijder de twee gele kunststof schroeven aan de linker- en rechterkant van lade 2. 72 Hoofdstuk 3 Hoe...
De printer aansluiten en inschakelen 1. Sluit de rolmodule op de printer aan met de meegeleverde kabel. De rolmodule is voorzien van een tweede connector voor een optioneel accessoire. VOORZICHTIG NLWW Deze connector mag niet voor andere toepassingen worden gebruikt. 2. Uw printer kan direct op een computer of via een netwerk op een of meer computers worden aangesloten. 3. De printer is voorzien van een Fast-Ethernet-aansluiting voor een netwerkverbinding.
5. Sluit het netsnoer op de achterkant van de printer aan en steek het andere uiteinde in een stopcontact. 6. Zet de aan/uit-schakelaar aan de achterkant van de printer in de stand Aan. 7. Als het aan/uit-lampje op het voorpaneel niet gaat branden, drukt u op de aan/uit-toets om de printer aan te zetten. > Opmerking 8. 74 Wacht ongeveer tien minuten tot dit bericht verschijnt. Markeer uw taal met behulp van de toetsen Omhoog en Omlaag. Druk op de toets Selecteren. Hoofdstuk 3 Hoe...
De inktpatronen installeren NLWW 1. Het voorpaneel geeft aan hoe u de inktpatronen installeert. 2. Haal de printkoppen, printkopreinigers en inktpatronen uit de doos met verbruiksartikelen. 3. Zoek de inktpatroondeur aan de linkerkant van de printer. 4. Open de inktpatroondeur.
76 5. Trek de blauwe hendel voorzichtig omlaag om de inktpatroonlade te ontgrendelen. 6. Schuif de inktpatroonlade naar buiten. 7. Plaats de inktpatroon op de lade. Merktekens op de lade geven de juiste locatie aan. 8. Zet de inktpatroon aan de achterkant van de lade, zoals is aangegeven in de figuur. Hoofdstuk 3 Hoe...
9. Duw de inktpatroonlade weer in de printer tot deze vastklikt. 10. Installeer de overige drie inktpatronen op dezelfde manier. 11. Sluit de inktpatroondeur. De printkoppen installeren 1. NLWW Wacht ongeveer een minuut tot dit voorpaneelbericht verschijnt.
78 2. Open het printervenster. 3. Verwijder de verpakkingstape waarmee de vergrendeling van de printkopwagen is vastgezet. 4. Trek de vergrendeling aan de bovenkant van de wagen omhoog en laat deze weer los. 5. Til de afdekplaat omhoog. Hierdoor krijgt u toegang tot de installatiekoppen. Hoofdstuk 3 Hoe...
NLWW 6. Voordat u de installatiekoppen verwijdert, kijkt u via het venster aan de bovenkant van elke kop of de kop inkt bevat. 7. Zet de blauwe hendel omhoog om een installatiekop te verwijderen. 8. Gebruik de blauwe hendel om de installatiekop voorzichtig uit de wagen te halen. 9. Til de installatiekop omhoog tot deze loskomt uit de wagen. Verwijder vervolgens de overige installatiekoppen.
10. Verwijder de blauwe beschermkap en de transparante beschermtape van de printkop. 11. Laat alle printkoppen verticaal in de juiste positie zakken. 12. Installeer de printkoppen traag en voorzichtig. 13. Controleer of de printkoppen goed vastzitten. Wanneer alle printkoppen zijn geïnstalleerd, verschijnt het bericht Close printhead cover and window (Sluit afdekplaat en venster van printkoppen) op het voorpaneel. 14.
15. Sluit de afdekplaat van de wagen. 16. Controleer of de vergrendeling goed vastklikt. 17. Sluit het printervenster. 18. Wacht ongeveer een minuut tot de printer de printkoppen heeft gecontroleerd. De printkopreinigers installeren 1. NLWW Wacht tot dit voorpaneelbericht verschijnt.
82 2. Druk op de deur van de printkopreinigers aan de rechterkant van de printer. 3. Open de deur van de printkopreinigers. 4. Plaats de printkopreiniger in de juiste sleuf (afhankelijk van de kleur). 5. Duw de printkopreiniger naar binnen en omlaag tot deze vastklikt. Hoofdstuk 3 Hoe...
6. Plaats de overige zeven printkopreinigers in de juiste sleuven. 7. Sluit de deur van de printkopreinigers. Rol 1 laden 1. Wacht tot dit voorpaneelbericht verschijnt en druk vervolgens op de toets Selecteren. 2. Als u de rol papier uit lade 1 in de printer wilt laden, markeert u op het voorpaneel het pictogram en drukt u op de toets Selecteren.
84 3. Markeer Paper load (Papier laden) en druk op de toets Selecteren. 4. Markeer Load roll 1 (Rol 2 laden) en druk op de toets Selecteren. 5. Markeer het type papier dat u wilt laden en druk op de toets Selecteren. 6. Trek lade 1 met twee handen naar buiten. Hoofdstuk 3 Hoe...
7. Verwijder de as uit lade 1. 8. Gebruik de meegeleverde kernadapters als de rolkern een grotere diameter heeft. 9. Verwijder de blauwe stop aan het linkeruiteinde van de as. Houd de as horizontaal. 10. Schuif de papierrol die bij de printer is geleverd, op de as. Zorg dat u het papier exact zoals in de figuur houdt.
11. Druk de zwarte rechterstop op de rol. Controleer of de stop goed is geplaatst. 12. Plaats de blauwe stop op de as. 13. Druk de blauwe linkerstop op de rol. Controleer of de stop goed is geplaatst. 86 Hoofdstuk 3 Hoe...
14. Houd de as vast bij de blauwe en zwarte stoppen. 15. Plaats de as in lade 1 met de blauwe stop aan de linkerkant. 16. Zet de papierladingshendel van lade 1 omhoog. Deze hendel bevindt zich aan de rechterkant van de printer, boven lade 1. 17. Schuif het papier van rol 1 op de plaat van lade 1. Lijn het papier uit met de middelste blauwe lijn aan de rechterkant van de plaat.
18. Stop met het invoeren van papier als de printer een geluidssignaal geeft. 19. Zet de papierladingshendel van lade 1 omlaag. 20. Duw lade 1 naar binnen. 88 Hoofdstuk 3 Hoe...
21. Draai het overtollige papier voorzichtig terug op de as met behulp van de stoppen op beide uiteinden van de as. 22. Selecteer de rollengte, als deze bekend is. Rol 2 laden NLWW 1. Als u de rol papier uit lade 2 wilt laden, markeert u op het voorpaneel het pictogram op de toets Selecteren. 2. Markeer Paper load (Papier laden) en druk op de toets Selecteren.
90 3. Markeer Load roll 2 (Rol 2 laden) en druk op de toets Selecteren. 4. Markeer het type papier dat u wilt laden en druk op de toets Selecteren. 5. Trek lade 2 met twee handen naar buiten. 6. Verwijder de as uit lade 2. 7. Laad de as op dezelfde manier als is beschreven voor rol 1. Hoofdstuk 3 Hoe...
8. Plaats de as in lade 2 met de blauwe stop aan de linkerkant. 9. Zet de papierladingshendel van lade 2 omhoog. Deze hendel bevindt zich aan de rechterkant van de printer, onder lade 1. 10. Schuif het papier van rol 2 op de plaat van lade 2. Lijn het papier uit met de middelste blauwe lijn aan de rechterkant van de plaat.
11. Stop met het invoeren van papier als de printer een geluidssignaal geeft. 12. Zet de papierladingshendel van lade 2 omlaag. 13. Duw lade 2 met twee handen naar binnen. 92 Hoofdstuk 3 Hoe...
14. Draai het overtollige papier voorzichtig terug op de as met behulp van de stoppen op beide uiteinden van de as. De bak in elkaar zetten NLWW 1. Zoek alle onderdelen voor de bak. Gebruik dezelfde schroevendraaier als waarmee u de rolmodule op de printervoet hebt bevestigd. 2. Leg één eindframe op de vloer. Plaats één dwarsframe verticaal met het schuine gedeelte tegen de bovenkant van het eindframe. Bevestig dit dwarsframe aan de binnenkant van de kortste steun van het eindframe.
3. Zet het dwarsframe aan het eindframe vast met twee schroeven. 4. Zet de bak horizontaal. Zet het dwarsframe aan de korte steun van het tweede eindframe vast met twee schroeven. 5. Zet het tweede dwarsframe aan de bak vast met vier schroeven. Opmerking 94 Hoofdstuk 3 Bevestig dit dwarsframe aan de buitenkant van de eindframes. Hoe...
NLWW 6. Bevestig één uiteinde van de lus aan het dwarsframe. 7. Bevestig het andere uiteinde van de lus aan het dwarsframe. 8. Bevestig de overige vijf lussen op dezelfde manier. 9. Plaats de bak tegen de printer.
96 Hoofdstuk 3 Hoe...
4 NLWW Hoe...
Een verbindingsmethode selecteren U kunt de printer op de volgende manieren aansluiten. Verbindingstype Snelheid Kabellengte Andere factoren Fast Ethernet Snel; de snelheid is afhankelijk van het netwerkverkeer Lang (100 m = 328 ft) Vereist extra materiaal (switches). Gigabit Ethernet (optioneel accessoire) Heel snel; de snelheid is afhankelijk van het netwerkverkeer Lang (100 m = 328 ft) Vereist extra materiaal (switches).
Automatische IP-adresconfiguratie In deze situatie genereert de printer automatisch een IP-adres nadat de netwerkkabel is aangesloten en de printer is opgestart. U moet deze waarde ophalen en de volgende procedure uitvoeren om de printer in het netwerk op te nemen: 1. Selecteer het pictogram 2. Op het voorpaneel verschijnen verschillende gegevens, zoals het IP-adres van de printer. Noteer het IP-adres (in dit voorbeeld 16.23.61.128). 3.
3. Plaats de cd Driver and Documentation in het cd-rom-station van de computer. Als de cd niet automatisch wordt gestart, voert u het programma START.EXE in de hoofdmap van de cd uit. 4. Klik op de knop Install (Installeren). 5. Volg de instructies op het scherm om het printerstuurprogramma te installeren. Aan de hand van de onderstaande opmerkingen begrijpt u de schermen beter en kunt u de juiste keuzes maken. 6.
Het printerstuurprogramma verwijderen (Windows) 1. Plaats de cd Drivers and Documentation in het cd-rom-station. Als de cd niet automatisch wordt gestart, voert u het programma START.EXE in de hoofdmap van de cd uit. 2. Kies Install (Installeren) en volg de instructies op het scherm om het printerstuurprogramma te verwijderen.
Handmatige verbinding via Bonjour/Rendezvous Zo sluit u uw printer aan met Bonjour/Rendezvous: 1. op het voorpaneel en selecteer I/O setup I/O-configuratie) > Fast Selecteer het pictogram Ethernet (of Gigabit Ethernet, als u deze optie gebruikt) > View configuration (Configuratie weergeven). Noteer de mDNS-servicenaam van uw printer (deze wordt op het voorpaneel weergegeven). Mogelijk hebt u deze in een latere stap nodig. 2.
Handmatige verbinding via TCP/IP Zo sluit u uw printer aan met TCP/IP: 1. Selecteer het pictogram 2. Op het voorpaneel verschijnen verschillende gegevens, zoals het IP-adres van de printer. Noteer het IP-adres (in dit voorbeeld 16.23.61.128). 3. Open Printerconfiguratie en kies Voeg printer toe in het menu Printers (of kies Voeg toe in de lijst Hulpprogramma's in eerdere versies van Mac OS X). 4. Selecteer TCP/IP-printer in het pop-upmenu. 5. Selecteer Socket/HP Jetdirect. 6.
2. Op het voorpaneel verschijnen verschillende gegevens, zoals het IP-adres van de printer. Noteer het IP-adres (in dit voorbeeld 16.23.61.128). 3. Open Desktop Printer Utility in de map HP Designjet 4000ps op de vaste schijf van uw computer. 4. Selecteer het AdobePS-stuurprogramma en de LPR-printerverbinding. Klik op OK. 5. Gebruik de eerste Wijzig-knop om het PPD-bestand (PostScript Printer Description) HP Designjet 4000 PS3 te selecteren. 6.
8. Het type printer wordt automatisch geselecteerd. Er verschijnt een nieuw printerpictogram op het bureaublad. 9. Sluit de Kiezer. Er verschijnt een pictogram op het bureaublad. Direct aansluiten op een computer (Mac OS X) U kunt de printer direct op een computer aansluiten zonder via een netwerk te werken. Hiervoor gebruikt u de ingebouwde FireWire-aansluiting (IEEE 1394) of de optionele USB 2.0-aansluiting van de printer. Installeer eerst het printerstuurprogramma op de computer. 1.
5. Selecteer USB. 6. Er wordt mogelijk een bericht weergegeven dat er nieuwe stuurprogramma's zijn gedetecteerd. Klik op OK om deze te laden. 7. Selecteer de printer in de lijst. 8. Klik op de knop Voeg toe. 9. Het printerpictogram wordt automatisch toegevoegd aan de lijst van beschikbare printers. Opmerking Alleen in Mac OS X 10.2 wordt de nieuwe printer weergegeven als Algemeen.
9. Sluit de USB-kabel op de printer en de computer aan. 10. Zet de printer aan. 11. Open Desktop Printer Utility in de map HP Designjet 4000ps. 12. Selecteer het AdobePS-stuurprogramma en de USB-verbinding. 13. Klik op de knop Wijzig in het deelvenster Selectie USB-printer om de printer te selecteren. 14. Klik op de knop Autoconfig om de printer automatisch te configureren. U kunt op de knop Wijzig klikken om het PPD-bestand (PostScript Printer Description) te selecteren. 15.
Het printerstuurprogramma verwijderen (Mac OS 9) [4000] Opmerking Dit onderwerp is alleen van toepassing op de HP Designjet 4000-printerserie. 1. Plaats de cd Drivers and Documentation in het cd-rom-station. 2. Ga in de Finder naar de cd. 3. Dubbelklik op OS 9 HP DJ 4000ps Install om het installatieprogramma te starten. 4. Het installatieprogramma helpt u bij het uitvoeren van verschillende stappen en vervolgens bereikt u het hoofdinstallatievenster.
5 NLWW Hoe...
De printer in- en uitschakelen Tip De printer voldoet aan de Energy Star-norm en hoeft niet te worden uitgeschakeld om stroom te besparen. Als u de printer ingeschakeld laat staan, kunt u vrijwel direct afdrukken en is het systeem in zijn totaliteit betrouwbaarder. Nadat de printer een bepaalde periode niet is gebruikt (standaard 30 minuten), wordt de energiebesparende slaapstand ingeschakeld.
De printer opnieuw starten In bepaalde omstandigheden kan het nodig zijn de printer opnieuw op te starten. Ga dan als volgt te werk: 1. Druk op de aan/uit-toets op het voorpaneel om de printer uit te schakelen, wacht een paar seconden en druk nogmaals op de aan/uit-toets. Hierdoor hoort de printer opnieuw op te starten. Als dat niet het geval is, gaat u naar stap 2. 2. Gebruik de toets Reset op het voorpaneel. U hebt een pen nodig om de toets Reset in te drukken.
Toegang krijgen tot de geïntegreerde webserver Met behulp van de geïntegreerde webserver kunt u uw printer en afdruktaken op afstand beheren via een gewone webbrowser op een willekeurige computer. Opmerking Voor het gebruik van de geïntegreerde webserver hebt u een TCP/IP-verbinding met de printer nodig. Als u een AppleTalk-, Novell- of USB-verbinding met de printer hebt, kunt u de geïntegreerde webserver niet gebruiken.
Als u de FireWire-poortconfiguratie niet naar de eerste positie van de lijst met poortconfiguraties sleept, moet u Handmatig (of DHCP met handmatig adres) kiezen in het pop-upmenu Configureer IPv4 en vervolgens een IP-adres invoeren. Ga naar http://www.apple.com/ voor meer details of actuele informatie over het activeren van IP via FireWire.
Opmerking Als u het wachtwoord vergeet, gaat u naar De browser heeft geen toegang tot de geïntegreerde webserver. E-mailmelding van bepaalde fouten instellen 1. Ga in de geïntegreerde webserver via het tabblad Settings (Instellingen) naar de pagina E-mail server (E-mailserver) en controleer of de volgende velden correct zijn ingevuld: ● SMTP server (SMTP-server): het IP-adres van de server voor uitgaande e-mail (SMTP), die alle uitgaande e-mailberichten van de printer verwerkt.
De zoemer uitzetten Als u de zoemer van de printer wilt in- of uitschakelen, selecteert u het pictogram op het voorpaneel en kiest u Printer configuration (Printerconfiguratie) > Front panel options (Voorpaneelopties) > Enable buzzer (Zoemer inschakelen).
116 Hoofdstuk 5 Hoe...
6 NLWW Hoe...
Een rol op de as plaatsen [4000] Opmerking Dit onderwerp is alleen van toepassing op de HP Designjet 4000-printerserie. 1. Zorg dat de printerwielen zijn vergrendeld (de remhendel moet omlaag staan) om te voorkomen dat de printer wegrolt. 2. Zet de ashendel omlaag. 3. Haal het rechteruiteinde van de as (1) uit de printer en trek de as naar rechts om het andere uiteinde (2) te kunnen verwijderen. Plaats uw vingers niet in de assteunen tijdens het verwijderen.
6. De rol kan heel lang zijn. Leg de as horizontaal op een tafel en laad de rol op de tafel. Mogelijk zijn twee personen nodig om de rol vast te houden. 7. Schuif de nieuwe rol op de as. Zorg dat u het papier zoals in de figuur houdt. Als het papier niet juist is geplaatst, verwijdert u de rol, draait u deze 180° en schuift u de rol weer op de as. Opmerking Ook op de as wordt de juiste richting aangegeven. Zorg dat er geen speling tussen de rol en de vaste stop op het rechteruiteinde van de as is.
10. Schuif de as met de blauwe papierstop links eerst aan de linkerkant en vervolgens aan de rechterkant in de printer, zoals wordt aangegeven door pijl 1 en 2. 11. Controleer of de ashendel in de bovenste stand (horizontaal) staat. Als dat het geval is, bevindt het juiste uiteinde van de as zich in de printer. Indien nodig kunt u de hendel zelf omzetten. Als u regelmatig van papiertype verandert, kunt u de rollen sneller vervangen door verschillende typen rollen vooraf op verschillende assen te plaatsen.
NLWW 2. Er verschijnt een lijst van papiertypen op het voorpaneel. 3. Selecteer het papiertype dat u wilt gebruiken. Als u niet zeker weet welk type u moet selecteren, gaat u naar Ondersteunde papiertypen selecteren. 4. Wacht tot u wordt gevraagd het venster te openen. 5. Zet de papierladingshendel omhoog. 6. Trek ongeveer één meter (3 ft) papier van de rol.
7. Plaats de rand van de papierrol voorzichtig boven de zwarte rol. WAARSCHUWING Zorg dat u bij het laden van papier de rubberen wieltjes van de plaat niet aanraakt, omdat deze wieltjes kunnen gaan draaien en huid, haar of kleding hierin kunnen komen vast te zitten. WAARSCHUWING Plaats uw vingers niet in het papierpad van de printer. De printer is niet ontworpen voor vingers en het gevolg kan pijnlijk zijn. 8. Wacht tot het papier uit de printer wordt gevoerd, zoals hieronder is afgebeeld.
10. Wanneer het papier correct is uitgelijnd met de blauwe lijn en de halve cirkel, zet u de papierladingshendel omlaag. 11. U wordt gevraagd het overtollige papier op de rol te draaien. 12. Draai het overtollige papier op de rol. Gebruik de papierstop om de rol in de aangegeven richting te draaien. 13. Laat het venster zakken. 14. U wordt nogmaals gevraagd het overtollige papier op de rol te draaien.
15. Als het gebruikte papiertype nog niet is gekalibreerd en kleurkalibratie is ingeschakeld, voert de printer een kleurkalibratie uit. Zie Kleurkalibratie uitvoeren. 16. Het bericht Ready (Gereed) verschijnt op het voorpaneel om aan te geven dat de printer gereed is om af te drukken. Een rol uit de printer verwijderen [4000] Opmerking Dit onderwerp is alleen van toepassing op de HP Designjet 4000-printerserie.
3. Trek het papier aan de voorzijde uit de printer. 4. Druk de ashendel omlaag en verwijder de lege as uit de printer (trek eerst het rechteruiteinde naar buiten). Plaats uw vingers niet in de assteunen tijdens het verwijderen. 5. Zet de papierladingshendel omlaag. 6. Wanneer op het voorpaneel een waarschuwingsbericht wordt weergegeven, drukt u op de toets Selecteren om het bericht te wissen. Geen papier zichtbaar Wanneer het uiteinde van de rol volledig in de printer is verdwenen: 1.
126 4. Wacht tot u wordt gevraagd het venster te openen. 5. Zet de papierladingshendel omhoog. 6. Plaats het vel in de printer zoals hieronder is afgebeeld. Hoofdstuk 6 Hoe...
7. Voer het vel in de printer tot het weer uit de printer komt, zoals hieronder is afgebeeld. WAARSCHUWING Zorg dat u bij het laden van papier de rubberen wieltjes van de plaat niet aanraakt, omdat deze wieltjes kunnen gaan draaien en huid, haar of kleding hierin kunnen komen vast te zitten. WAARSCHUWING Plaats uw vingers niet in het papierpad van de printer. De printer is niet ontworpen voor vingers en het gevolg kan pijnlijk zijn. 8. Trek het vel aan de bovenkant uit de printer. 9.
11. Zet de papierladingshendel omlaag. 12. Als het papier goed is geladen, verschijnt het bericht Ready (Gereed) op het voorpaneel om aan te geven dat de printer gereed is om af te drukken. Als er iets is misgegaan (papier niet goed geplaatst of uitgelijnd), volgt u de instructies op het voorpaneel. 13. Als u afdrukt op een vel papier met een lengte van minder dan 900 mm (maximaal A1-formaat), moet u de drie verplaatsbare stoppers op de bak gebruiken.
1. Druk op de grijze toets en verwijder de blauwe papierstop van de as. 2. Als de rol een kartonnen kern van 7,6 cm (3 inch) heeft, controleert u of de kernadapters die bij de printer zijn geleverd, zijn geïnstalleerd. Zie verderop: 3. De rol kan lang en zwaar zijn. Leg de as horizontaal op een tafel en laad de rol op de tafel. Mogelijk zijn twee personen nodig om de rol vast te houden. 4. Schuif de nieuwe rol op de as. Zorg dat u het papier zoals in de figuur houdt.
6. Zorg dat er geen speling tussen de rol en de zwarte stop is. 7. Plaats de blauwe papierstop op het andere uiteinde van de as en druk de stop naar het uiteinde van de rol. 8. Zorg dat er geen speling tussen de rol en de blauwe stop is. Als u regelmatig van papiertype verandert, kunt u de rollen sneller vervangen door verschillende typen rollen vooraf op verschillende assen te plaatsen. Extra assen kunnen afzonderlijk worden aangeschaft.
1. op het voorpaneel van de printer en kies Paper load (Papier laden) > Selecteer het pictogram Load roll 1 (Rol 1 laden) of Load roll 2 (Rol 2 laden). Tip Deze stap is optioneel. U kunt deze stap overslaan en beginnen met het plaatsen van de rol door de lade uit te trekken zoals hieronder is afgebeeld. 2. Til de lade enigszins omhoog en trek deze vervolgens naar u toe. 3. Plaats de rol en de as in de lade. Houd de rol zoals wordt aangegeven op de papierstoppen aan beide uiteinden van de as.
4. Zet de papierladingshendel omhoog. Gebruik de bovenste hendel voor de bovenste rol en de onderste hendel voor de onderste rol. 5. Zorg dat de bovenrand van het papier niet te veel is gekreukt, gescheurd of gekruld, omdat dit kan leiden tot een papierstoring. Snijd indien nodig de bovenrand af voordat u het papier laadt (zie Papier snijden met de handmatige snijfunctie [4500]). 6. Plaats de rand van de papierrol voorzichtig in het voorpad. WAARSCHUWING Plaats uw vingers niet in het voorpad.
9. Schuif de lade terug op zijn plaats. 10. Draai het overtollige papier weer op de rol. Gebruik de papierstop om de rol in de aangegeven richting te draaien. 11. Er verschijnt een lijst van papiertypen op het voorpaneel. 12. Selecteer het papiertype dat u wilt gebruiken. Als u niet zeker weet welk type u moet selecteren, gaat u naar Ondersteunde papiertypen selecteren. 13. U wordt gevraagd de lengte op te geven van de rol die u laadt. Als u de lengte hebt opgegeven, wordt de rol geladen.
Als ook deze tweede poging mislukt, wordt nogmaals geprobeerd de rol te laden, maar dit keer wordt uw hulp gevraagd. 15. Als het gebruikte papiertype nog niet is gekalibreerd en kleurkalibratie is ingeschakeld, voert de printer een kleurkalibratie uit. Zie Kleurkalibratie uitvoeren. 16. Het bericht Ready (Gereed) verschijnt op het voorpaneel om aan te geven dat de printer gereed is om af te drukken. De rol waarmee momenteel kan worden afgedrukt, is gemarkeerd op het voorpaneel (in dit voorbeeld rol 1).
4. Druk op de toets Selecteren. 5. Til de lade enigszins omhoog en trek deze vervolgens naar u toe. 6. Haal de rol uit de printer (trek eerst het rechteruiteinde naar buiten). Plaats uw vingers niet in de assteunen tijdens het verwijderen. Rol is niet meer bevestigd aan as Wanneer het uiteinde van de rol zichtbaar is maar niet meer bevestigd is aan de as: 1.
Papier snijden met de handmatige snijfunctie [4500] Opmerking Dit onderwerp is alleen van toepassing op de HP Designjet 4500-printerserie. U kunt met de handmatige snijfunctie de bovenrand van het papier afsnijden wanneer deze vuil of ongelijkmatig is. Hiermee kunnen papierstoringen tijdens het laden worden voorkomen. 136 1. Open de lade van de rol die u wilt afsnijden. 2. Trek met uw linkerhand de bovenrand van het papier over de bovenkant van de rol en vervolgens omlaag voor de lade langs. 3.
NLWW 4. Pak met uw rechterhand de papiersnijder vast en draai deze zoals aangegeven op de bovenkant van de papiersnijder om de eerste insnijding te maken en trek de snijder vervolgens voorzichtig door het papier. 5. Verwijder het afgesneden stuk papier. 6. Draai de as naar achteren om de papierrand omhoog te verplaatsen.
7. Duw de papiersnijder terug naar de rechterkant van de lade. Informatie over het papier weergeven Selecteer het pictogram of op het voorpaneel van de printer, kies Paper information (Papierinformatie) en kies de papierbron waarvoor u informatie wilt weergeven. De volgende informatie verschijnt op het voorpaneel: ● de status van de rol of het vel papier Opmerking De HP Designjet 4500-printerserie kan alleen afdrukken op papierrollen.
papier koopt waarvoor uw printer geen mediaprofiel heeft, kunt u dat papiertype niet op het voorpaneel selecteren. Als u het juiste mediaprofiel wilt downloaden, gaat u naar: ● http://www.hp.com/support/designjet-downloads/ voor de HP Designjet 4000-serie ● http://www.hp.com/support/designjet/profiles4500/ voor de HP Designjet 4500 ● http://www.hp.com/support/designjet/profiles4500ps/ voor de HP Designjet 4500ps ● http://www.hp.
140 Hoofdstuk 6 Hoe...
7 NLWW Hoe...
Een taak verzenden via de geïntegreerde webserver 1. Open de geïntegreerde webserver (zie Toegang krijgen tot de geïntegreerde webserver). 2. Ga naar de pagina Submit job (Taak verzenden). 3. Selecteer op uw computer het bestand dat u wilt afdrukken. Opmerking Voor het verzenden van een taak die u via de geïntegreerde webserver wilt afdrukken, hoeft het printerstuurprogramma of de toepassing waarin het bestand is gemaakt, niet op uw computer te zijn geïnstalleerd. 4.
Opmerking Als u een taak later opnieuw wilt afdrukken zonder wijzigingen, kunt u dit vanuit de afdrukwachtrij doen zonder dat u de taak hoeft op te slaan. U kunt een taak alleen opslaan terwijl u deze verzendt voor afdrukken: 1. Open de geïntegreerde webserver (zie Toegang krijgen tot de geïntegreerde webserver). 2. Ga naar de pagina Submit job (Taak verzenden). 3. Selecteer op uw computer het bestand dat u wilt afdrukken. 4.
De wachtrij uitschakelen [4000] Gebruikers van de HP Designjet 4000-serie kunnen de wachtrij uitschakelen via de webserver (tabblad Settings (Instellingen) > Device setup (Apparaatconfiguratie) > Queue (Wachtrij)) of via het voorpaneel. Selecteer hiertoe het pictogram > Disable queue (Wachtrij uitschakelen). en kies Job management options (Taakbeheeropties) Gebruikers van de HP Designjet 4500-serie kunnen de wachtrij niet uitschakelen.
Als nesten is ingeschakeld, is de bovenaan geplaatste taak mogelijk nog genest met andere taken. Als u deze taak wilt loskoppelen en als volgende taak wilt afdrukken, moet u eerst nesten uitschakelen en vervolgens de taak boven aan de wachtrij plaatsen, zoals hierboven is beschreven.
● on hold (onderbroken): de taak is verzonden met de optie on hold for preview (wachten op voorbeeld) en is onderbroken Opmerking Als de printer vastloopt tijdens het afdrukken van een taak en de wachtrijfunctie is ingeschakeld, wordt de gedeeltelijk afgedrukte taak in de wachtrij weergegeven met de markering on hold (onderbroken) wanneer de printer weer wordt ingeschakeld. Wanneer u het afdrukken van de taak hervat, wordt afgedrukt vanaf de pagina waarbij het afdrukken was onderbroken.
1. Richting van papierstroom 2. Nesten uit 3. Nesten aan 4. Papier bespaard door nesten Wanneer probeert de printer pagina's te nesten? Wanneer aan beide voorwaarden is voldaan: ● De printer bevat een papierrol, geen losse vellen. ● In het menu Job Management (Taakbeheer) van het voorpaneel of op de pagina van de geïntegreerde webserver staat Nest (Nesten) op On (Aan).
● Alle pagina's moeten dezelfde instelling voor Color Adjustment (Kleuraanpassing) hebben. Deze instellingen worden in het Windows-stuurprogramma Advanced Color Settings (Geavanceerde kleurinstellingen) en in het Mac OS-stuurprogramma CMYK Settings (CMYK-instellingen) genoemd. ● Alle pagina's moeten dezelfde kleurinstelling hebben: kleuren of grijstinten. Niet een aantal pagina's in kleur en een aantal pagina's met grijstinten.
8 Hoe... (onderwerpen over de stapelaar) [4500] Opmerking Dit hoofdstuk is alleen van toepassing op de HP Designjet 4500-printerserie. De stapelaar is een optionele accessoire voor HP Designjet 4500-printers. Hiermee worden afdrukken plat, boven op elkaar gelegd en vallen ze niet in de opvangbak.
De stapelaar installeren 1. Sluit de kabels van de stapelaar aan op de printer. 2. Zet de stapelaar aan. 3. op het voorpaneel van de printer en kies Accessories (Accessoires) Selecteer het pictogram > Stacker (Stapelaar) > Install stacker (Stapelaar installeren). U wordt gevraagd de stapelaar aan de printer te bevestigen. 4. De stapelaar heeft twee vergrendelingen die in de printerdeflectors grijpen.
3. Ontkoppel de kabels van de stapelaar. De temperatuur wijzigen De stapelaar is voorzien van een verwarmde rol waarmee het papier wordt ontkruld. Selecteer het pictogram op het voorpaneel van de printer en kies Accessories (Accessoires) > Stacker (Stapelaar) > Select temperature level (Temperatuurniveau selecteren) om de temperatuur van de rol te wijzigen. Er zijn drie opties: ● Normal (Normaal): dit is de standaardinstelling en tevens de aanbevolen instelling.
De rollen van de stapelaar reinigen WAARSCHUWING De stapelaar wordt warm tijdens het gebruik. Schakel de stapelaar uit en laat het apparaat afkoelen voordat u de rollen reinigt. Op de hoofdrol en de kleine uitvoerrollen van de stapelaar blijft vaak inkt achter. Reinig de rollen daarom regelmatig met een vochtige doek. Hoe vaak dit nodig is, hangt onder meer af van het papiertype dat u gebruikt.
De stapelaar verplaatsen of opbergen Voer de volgende stappen uit voordat u de stapelaar verplaatst of opbergt om de ruimte die de stapelaar inneemt te verkleinen. 1. NLWW Maak de schroeven aan beide kanten van het stapelaarplateau los en laat het plateau verticaal hangen.
2. 154 Verwijder de pin uit elke steun en draai de steunen naar boven. Hoofdstuk 8 Hoe...
9 NLWW Hoe...
Ander paginaformaat instellen U kunt het paginaformaat op de volgende manieren instellen: ● Via een Windows-printerstuurprogramma: klik op het tabblad Papier/Kwaliteit en selecteer Grootte is. ● Via een Mac OS-printerstuurprogramma: kies Pagina-instelling in het menu Archief, selecteer uw printer in het pop-upmenu Stel in voor en kies Papierformaat. ● Via de geïntegreerde webserver: ga naar het deelvenster Page Size (Paginaformaat) van de pagina Submit Job (Taak verzenden).
6. Klik op de knop OK. 7. Als u het nieuwe aangepaste papierformaat wilt gebruiken, moet u het printerstuurprogramma afsluiten en opnieuw openen. Via het PostScript-printerstuurprogramma voor Windows Me of Windows 98 1. Klik op het tabblad Papier/Kwaliteit. 2. Selecteer Aangepaste pagina 1, Aangepaste pagina 2 of Aangepaste pagina 3 in de lijst Grootte is. 3. Selecteer de breedte en lengte van de aangepaste pagina. 4. Klik op de knop OK.
Via de geïntegreerde webserver 1. Ga naar het deelvenster Page Size (Paginaformaat) van de pagina Submit Job (Taak verzenden). 2. Selecteer de optie Custom (Aangepast). 3. Selecteer de breedte en lengte van het gewenste papierformaat. Een andere afdrukkwaliteit instellen De printer beschikt over drie keuzemogelijkheden voor de afdrukkwaliteit: Best (Beste) Normal (Normaal) en Fast (Snel).
Image quality settings (Instellingen beeldkwaliteit) Print content (Afdrukgegevens) Lijnen (concept) Print quality (Afdrukkwaliteit) Optimized for (Geoptimaliseerd voor) Maximum detail (Max.
Image quality settings (Instellingen beeldkwaliteit) Print content (Afdrukgegevens) Renderings Print quality (Afdrukkwaliteit) Optimized for (Geoptimaliseerd voor) Maximum detail (Max. details) Best Images (Afbeeldingen) Off (Uit) Papiertypen Heavyweight Coated Paper Productivity Photo Gloss Foto's Best Images (Afbeeldingen) Off (Uit) Productivity Photo Gloss * Doorschijnende materialen zijn: Vellum, Translucent Bond, Natural Tracing Paper, Heldere Film en Matte Film.
Marges aanpassen De printermarges bepalen het afdrukbare gebied van de pagina dat door uw toepassing kan worden gebruikt. Er zijn drie margeopties: Small (Klein), Normal (Normaal) en Extended (Uitgebreid) (zie ook Afdrukken zonder toegevoegde marges). Zie Functionele specificaties voor de afmetingen van de marges. U kunt de marges op de volgende manieren instellen: ● via het HP-GL/2 -printerstuurprogramma voor Windows: standaard worden normale marges geselecteerd.
● Via de geïntegreerde webserver: ga naar de pagina Submit Job (Taak verzenden) en selecteer Oversize (Te groot) in de lijst Margin (Marge). ● Via het voorpaneel: kies Default printing options (Standaardafdrukopties) > Paper options (Papieropties) > Select layout (Indeling selecteren) > Oversize (Te groot). Wanneer u te grote pagina's gebruikt, kunt u de breedte van de marges op de gebruikelijke manier selecteren (zie Marges aanpassen). Zie ook Afdrukken zonder toegevoegde marges.
● De breedte van een liggende afbeelding is groter dan de hoogte (een brede afbeelding) U moet de afdrukstand kiezen die de afbeelding heeft wanneer u de afbeelding op het scherm ziet. Wanneer u een liggende afbeelding met een staande afdrukstand afdrukt of omgekeerd, wordt de afbeelding mogelijk afgesneden tijdens het afdrukken. U kunt de afdrukstand instellen met een printerstuurprogramma of de geïntegreerde webserver.
Dit kan op de volgende manieren: ● Via een Windows-printerstuurprogramma: klik op het tabblad Finishing (Afwerking) en selecteer Rotate by 90 degrees (90 graden roteren). ● Via een Mac OS-printerstuurprogramma: klik op het tabblad Finishing (Afwerking) en selecteer Rotate (Roteren). ● Via de geïntegreerde webserver: ga naar de pagina Submit Job (Taak verzenden) en selecteer Rotate (Roteren).
wanneer achtergrondverlichting wordt toegepast. Als u de afbeelding niet wilt aanpassen in uw toepassing, gaat u als volgt te werk: ● Via een Windows-printerstuurprogramma: klik op het tabblad Finishing (Afwerking) en selecteer Mirror image (Afbeelding spiegelen). ● Via een Mac OS-printerstuurprogramma: klik op het tabblad Finishing (Afwerking) en selecteer Mirror image (Afbeelding spiegelen).
Als u afdrukt op één vel, moet u zorgen dat de afbeelding op de pagina past omdat deze anders wordt afgesneden. De paletinstellingen wijzigen Het palet Factory (Standaard) kan niet worden gewijzigd, maar u kunt wel Palet A en B definiëren. Deze paletten worden alleen toegepast op HP-GL/2-taken zonder geïntegreerd softwarepalet. Opmerking Alle HP-GL/2-taken die worden gegenereerd door het HP-GL/2-stuurprogramma dat bij de printer wordt geleverd, bevatten een geïntegreerd softwarepalet.
Opmerking Het palet dat u zojuist hebt gedefinieerd, treedt alleen in werking als u het instelt als actief palet. Als u niet de gewenste resultaten bereikt, gaat u naar Peninstellingen lijken geen effect te hebben. De verwerking van overlappende lijnen wijzigen De instelling Merge (Samenvoegen) bepaalt de verwerking van overlappende lijnen in een afbeelding. Er zijn twee instellingen: Off (Uit) en On (Aan).
● Selecteer Automatic (Automatisch) als de printer moet bepalen welk type bestand wordt ontvangen. Deze instelling is geschikt voor de meeste softwaretoepassingen. ● Selecteer HP-GL/2 als u niet met PostScript-bestanden werkt en problemen ondervindt met beeldpositionering of timing. ● Selecteer PS als u alleen PostScript-bestanden afdrukt en uw PostScript-taken niet beginnen met de standaard PostScript-header (%!PS) en geen PJL-taalomschakelopdrachten bevatten.
10 Hoe...
Kleurkalibratie uitvoeren Kleurkalibratie verbetert de consistentie van kleuren tussen verschillende afdrukken en printers. Deze kalibratie wordt doorgaans uitgevoerd nadat een printkop is vervangen, of wanneer een nieuw papiertype wordt gebruikt dat nog niet is gekalibreerd voor de nieuwe printkop(pen). U kunt deze automatische kalibratie echter uitschakelen en een standaard kleurcorrectie gebruiken voor elk bekend papiertype. 1.
U kunt zwartpuntcompensatie op de volgende manieren instellen: ● Via een PostScript-printerstuurprogramma voor Windows: klik op het tabblad Color (Kleur) en selecteer Black point compensation (Zwartpuntcompensatie). ● Via een Mac OS-printerstuurprogramma: klik op het tabblad Color Options (Kleuropties) en selecteer Black point compensation (Zwartpuntcompensatie). ● Via de geïntegreerde webserver: ga naar de pagina Submit Job (Taak verzenden) en selecteer Black point compensation (Zwartpuntcompensatie).
De kleuremulatiemodus selecteren U kunt de kleuremulatiemodus op de volgende manieren instellen: ● Via een Windows-printerstuurprogramma: klik op het deelvenster Color Management (Kleurbeheer) van het tabblad Color (Kleur). ● Via een Mac OS-printerstuurprogramma: selecteer het deelvenster Color Options (Kleuropties). ● Via de geïntegreerde webserver: ga naar het deelvenster Color Management (Kleurbeheer) van de pagina Submit Job (Taak verzenden).
2. Open de afbeelding.
3. 4. 174 Nadat u de kleurruimte hebt gedefinieerd waarin u gaat werken, kunt u desgewenst een zachte proefafdruk maken. Dit betekent de definitieve afdruk van de afbeelding emuleren op het scherm. Hiervoor hebt u een ICC-profiel voor uw monitor nodig. Selecteer Weergave > Instellen proef > Eigen. Gebruik de volgende informatie om opties te selecteren in het venster Instellen proef. ● Profiel: kies het profiel op basis van het printermodel en het papiertype.
Stuurprogramma-instellingen Selecteer het tabblad Paper/Quality (Papier/Kwaliteit - Windows) of Image Quality (Beeldkwaliteit - Mac OS) en stel Print Quality (Afdrukkwaliteit) in op Best. Op het tabblad Kleur (Windows) of Kleuropties (Mac OS) beschikt u over de volgende opties voor kleurbeheer. Selecteer de optie die u in het dialoogvenster Afdrukken hierboven hebt geselecteerd (deelvenster Print Space (Afdrukruimte), optie Profile (Profiel)). NLWW ● sRGB: dit is de standaardkleurruimte.
Printerinstellingen Zorg dat de instelling van Paper Type (Papiertype) op het voorpaneel overeenkomt met het papier dat u wilt gebruiken. Nauwkeurige kleuren genereren met Adobe Photoshop CS (PostScript-stuurprogramma) In dit onderwerp wordt een van de vele manieren besproken waarop u goede controle kunt uitoefenen over de afgedrukte kleuren die u met uw printer kunt genereren. Voordat u begint, controleert u of het papiertype al is gekalibreerd. Toepassingsinstellingen 1.
2. Open de afbeelding.
3. 4. 178 Nadat u de kleurruimte hebt gedefinieerd waarin u gaat werken, kunt u desgewenst een zachte proefafdruk maken. Dit betekent de definitieve afdruk van de afbeelding emuleren op het scherm. Hiervoor hebt u een ICC-profiel voor uw monitor nodig. Selecteer Weergave > Instellen proef > Eigen. Gebruik de volgende informatie om opties te selecteren in het venster Instellen proef. ● Profiel: kies het profiel op basis van het printermodel en het papiertype.
Stuurprogramma-instellingen Als u de optie PostScript kleurbeheer in de toepassing selecteert, worden de kleurinstellingen van het stuurprogramma Invoerprofiel en Rendering Intent genegeerd. In deze situatie gebruikt het stuurprogramma het documentprofiel van de toepassing en de geselecteerde rendering.
Opmerking De kleuren van EPS-, PDF- en grijstintbeelden kunnen niet worden beheerd met behulp van DTP-toepassingen. Bovendien worden deze afbeeldingen niet goed weergegeven op een monitor. Toepassingsinstellingen 1. 180 Open Adobe InDesign en selecteer Kleurinstellingen in het menu Bewerken. ● Werkruimten: de werkruimte is de kleurruimte die u wilt gebruiken voor het bewerken van de afbeelding.
uitvoerapparaat, en vervolgens opnieuw van het CMYK-uitvoerapparaat naar het printerprofiel (gekalibreerd). In InDesign wordt u aangeraden de opdracht Instellen proef (Weergave > Instellen proef > Aangepast) te kiezen. Met deze opdracht kunt u bij het afdrukken het 'afdrukprofiel' in de bronruimte selecteren. U kunt ook een simulatie bekijken op uw monitor. U wordt aangeraden de volgende procedure uit te voeren: In InDesign heeft elk object zijn eigen kleurbeheer.
Stuurprogramma-instellingen Voor DTP-toepassingen wordt u aangeraden het PostScript-stuurprogramma te gebruiken, omdat dit de kleuren kan beheren in CMYK-gegevens, RGB-gegevens of beide tegelijk. Selecteer het tabblad Paper/Quality (Papier/Kwaliteit - Windows) of Image Quality (Beeldkwaliteit - Mac OS) en stel Print Quality (Afdrukkwaliteit) in op Best.
Opmerking De kleuren van EPS-, PDF- en grijstintbeelden kunnen niet worden beheerd met behulp van DTP-toepassingen. Bovendien worden deze afbeeldingen niet goed weergegeven op een monitor. Toepassingsinstellingen NLWW 1. Open QuarkXPress en kies Preferences (Voorkeuren) in het menu Bewerken (Windows) of het QuarkXPress-menu (Mac OS). Selecteer vervolgens Quark CMS in het dialoogvenster Preferences (Voorkeuren). 2. Zorg dat het selectievakje Color Management Active (Kleurbeheer actief) is ingeschakeld.
CMYK sources to CMYK destinations (Kleurbeheer CMYK-bronnen naar CMYK-doelen) bij de standaard bronprofielen voor CMYK in. 6. De selectie onder Display Simulation (Schermsimulatie) geeft aan hoe QuarkXPress de schermsimulatie moet uitvoeren: ● None (Geen) betekent dat er niets op het scherm hoeft te worden gesimuleerd. ● Monitor Color Space (Kleurruimte monitor) betekent dat alleen voor weergave wordt geconverteerd van het bronprofiel naar het schermprofiel.
Opmerking In QuarkXpress heeft elk object zijn eigen kleurbeheer. Vaste kleuren gebruiken het kleurenprofiel en de rendering die zijn geselecteerd in de standaard bronprofielen onder Solid Colors (RGB, CMYK of Hexachrome) (Vaste kleuren: RGB, CMYK of Hexachroom) in het dialoogvenster Color Management Preferences (Voorkeuren kleurbeheer). Aan geïmporteerde objecten worden eigen profielen en rendering toegewezen.
Nauwkeurige kleuren genereren met ESRI ArcGIS 9 ArcGIS is een schaalbaar softwaresysteem voor het maken, beheren, integreren, analyseren en verspreiden van geografische gegevens voor alle soorten organisaties, van een individu tot een wereldwijd gedistribueerd netwerk van mensen. De toepassing zendt altijd RGB-gegevens naar het printerstuurprogramma. U kunt kiezen uit verschillende printerengines.
2. Wanneer u klaar bent om af te drukken, kiest u File (Bestand) > Page and Print Setup (Paginaen afdrukinstellingen) en selecteert u het HP-GL/2- en RTL-stuurprogramma. 3. Klik op de knop Properties (Eigenschappen) en configureer het stuurprogramma als volgt. ● Stel op het tabblad Paper/Quality (Papier/Kwaliteit) de optie Print Quality (Afdrukkwaliteit) in op Best.
geheugenproblemen. Als deze problemen optreden, selecteert u bij Output Image Quality (Uitvoerkwaliteit afbeeldingen) een lagere instelling dan 'Best'. Het verzenden van een afbeelding met een hogere resolutie dan de invoerresolutie van de printer, biedt geen voordelen op het gebied van afdrukkwaliteit. 6. U kunt nu afdrukken (klik op OK). Afdrukken met ArcPress-printerengine 1. Het benodigde stuurprogramma moet zijn geïnstalleerd, hoewel dit alleen als poort wordt gebruikt. 2.
4. NLWW ● Klik op de knop Properties (Eigenschappen), selecteer het HP RTL (RGB) TrueColorstuurprogramma en selecteer de resolutie die naar de printer wordt verzonden. ● Selecteer het tabblad Color Adjustment (Kleuraanpassing) als u gamma, helderheid, contrast of verzadiging wilt aanpassen. U kunt een voorbeeld weergeven van de wijzigingen. U kunt nu afdrukken: klik op OK in dit dialoogvenster en in het dialoogvenster Print (Afdrukken).
190 Hoofdstuk 10 Hoe...
11 Hoe...
Een inktpatroon verwijderen Er zijn twee procedures voor het verwijderen van een inktpatroon. ● De inktpatroon is bijna leeg en u wilt deze vervangen door een nieuwe patroon voor onbeheerd afdrukken (u kunt de resterende inkt in de eerste patroon later opgebruiken). ● De inktpatroon is leeg of defect, en u moet deze vervangen om verder te kunnen afdrukken. VOORZICHTIG Verwijder geen inktpatronen tijdens het afdrukken.
NLWW 3. Ontgrendel de deur door op de bovenkant te drukken tot u een klik hoort. 4. Trek de deur volledig open. 5. Pak het blauwe lipje vast aan de voorkant van de patroon die u wilt verwijderen.
194 6. Trek het blauwe lipje omlaag. 7. Trek het vervolgens naar buiten, naar u toe. 8. De patroon schuift samen met de overeenkomstige lade naar buiten. Hoofdstuk 11 Hoe...
9. Til de patroon uit de lade. Opmerking Raak het patroonuiteinde dat u in de printer plaatst, niet aan omdat er zich inkt kan bevinden op de verbinding. Opmerking Bewaar inktpatronen die nog inkt bevatten, horizontaal om te vermijden dat er inkt uitloopt. 10. Het voorpaneel geeft aan welke inktpatroon ontbreekt. Een inktpatroon plaatsen NLWW 1. Zoek het etiket met de inktkleur op de nieuwe inktpatroon. Houd de inktpatroon zo dat u het etiket kunt zien boven aan de zijkant die naar u toe is gericht.
3. Plaats de inktpatroon in de patroonlade. Zet de patroon aan de achterkant van de lade, zoals hieronder is aangegeven. Opmerking Er is ook een grotere zwarte inktpatroon verkrijgbaar die de hele lengte van de lade in beslag neemt. 4. Schuif de lade en de patroon in de sleuf tot de lade vastklikt. Als u problemen ondervindt, gaat u naar Ik kan geen inktpatroon plaatsen. 196 Hoofdstuk 11 Hoe...
5. Wanneer alle patronen zijn geplaatst, sluit u de deur (druk op de deur tot deze vastklikt). 6. Op het voorpaneel verschijnt de bevestiging dat alle patronen correct zijn geplaatst. Een printkop verwijderen WAARSCHUWING Zorg dat de printerwielen zijn vergrendeld (de remhendel moet omlaag staan) om te voorkomen dat de printer wegrolt. De printkoppen mogen alleen worden vervangen wanneer de printer is ingeschakeld met de aan/uitschakelaar. 1.
198 3. Wanneer de verplaatsing van de wagen is voltooid, wordt u gevraagd het venster te openen. 4. Zoek de wagen. 5. Trek de vergrendeling aan de bovenkant van de wagen omhoog en laat weer los. 6. Til de afdekplaat omhoog. Hierdoor krijgt u toegang tot de printkoppen. Hoofdstuk 11 Hoe...
7. Zet de blauwe hendel omhoog om een printkop te verwijderen. 8. Gebruik de blauwe hendel om de printkop voorzichtig los te maken. 9. Trek de blauwe hendel voorzichtig omhoog tot de printkop los komt uit de wagen. VOORZICHTIG raken.
10. Het voorpaneel geeft aan welke printkop ontbreekt. Een printkop plaatsen 1. Als de printkop nieuw is: a. Verwijder de blauwe beschermkap door deze omlaag te trekken. b. Verwijder de transparante beschermtape op de spuitmondjes van de printkop door het papieren lipje los te trekken. De printkop is zo ontworpen dat u deze alleen in de juiste positie kunt plaatsen.
3. Druk de kop omlaag zoals is aangegeven door de pijl in de volgende figuur. Mogelijk voelt u enige weerstand bij het plaatsen van de nieuwe printkop. Oefen daarom stevige druk uit maar ga altijd voorzichtig te werk. Als u problemen ondervindt, gaat u naar Ik kan geen printkop plaatsen. 4. Plaats eventuele andere printkoppen die moeten worden geïnstalleerd en sluit de afdekplaat van de wagen.
5. Vergrendel de afdekplaat van de wagen. Wanneer de wagen correct is vergrendeld, ziet deze er als volgt uit: 6. Sluit het venster. 7. Op het voorpaneel verschijnt de bevestiging dat alle printkoppen correct zijn geplaatst. 8. Vervang nu de printkopreinigers voor alle printkoppen die u hebt vervangen. Zie Een printkopreiniger verwijderen en Een printkopreiniger plaatsen.
Als u deze frequentie wilt verhogen om eventuele problemen sneller te detecteren, selecteert u het pictogram en kiest u Printer configuration (Printerconfiguratie) > Printhead monitoring (Printkopcontrole) > Intensive (Intensief). Als de printkopcontrole op Intensive (Intensief) is ingesteld, verschijnt tijdens het afdrukken het volgende bericht op het voorpaneel en op de printerstatusbalk van de geïntegreerde webserver: Printing. Printhead monitoring (Afdrukken. Printkopcontrole.
Gebruik deze voor het reinigen van de elektrische contacten van de wagen en de printkop wanneer continu het bericht Reseat (Installeer opnieuw) of Replace (Vervang) naast de printkop verschijnt op het voorpaneel. 1. Haal een nieuw vochtig doekje uit de hoes. De doos van de wisser bevat een aantal doekjes. Wanneer alle doekjes zijn opgebruikt, neemt u contact op met de klantenondersteuning. 204 2. Open de wagencontactwisser. 3.
5. Open de printkopwagenvergrendeling en verwijder de defecte printkop zoals is aangegeven op het voorpaneel. Zie Een printkop verwijderen. 6. Plaats de wagencontactwisser achter in de printkopsleuf. Veeg de elektrische contacten schoon door de wisser tussen de elektrische contacten achter in de sleuf en de stalen veer te plaatsen, met het doekje naar de elektrische contacten toe. Probeer geen inktafzetting te absorberen die zich mogelijk op de bodem van de sleuf bevindt.
9. Gebruik hetzelfde doekje om de onderste reeks elektrische contacten van de printkop te reinigen (tenzij de printkop nieuw is), maar raak de bovenste reeks elektrische contacten niet aan. VOORZICHTIG Raak het printkopoppervlak met de spuitmondjes niet aan, omdat deze makkelijk beschadigd raken. 10. Laat beide connectoren even drogen en plaats vervolgens de printkop weer in de wagen. Zie Een printkop plaatsen. 11.
13. Gooi het vuile doekje op een veilige plaats weg om te voorkomen dat er inkt terechtkomt op uw handen of kleding. Als het bericht Reseat (Installeer opnieuw) of Replace (Vervang) niet verdwijnt, vervangt u de printkop of neemt u contact op met de klantenondersteuning. De printkoppen uitlijnen Normaal gesproken lijnt de printer de printkoppen uit wanneer u een of meer koppen vervangt. Als er geen papier is geladen wanneer u een printkop vervangt, worden de koppen uitgelijnd zodra u papier laadt.
3. 4. Als het begin van de rol dichtbij is, wordt op het voorpaneel aangegeven dat de printer mogelijk maximaal 3 m (10 ft) papier moet invoeren voordat het uitlijnen kan worden gestart. Dit is nodig voor een correcte uitlijning. Als deze melding verschijnt, hebt u de volgende mogelijkheden: ● verdergaan met het uitlijnen van de printkoppen.
2. Open de deur. 3. Elke printkopreiniger is aan de voorkant voorzien van een lipje. U verwijdert de reiniger door het lipje naar binnen en naar boven te drukken (zoals wordt aangegeven door de pijl) tot de reiniger uit de sleuf komt. 4. Til de printkopreiniger uit de sleuf en schuif de reiniger vervolgens horizontaal uit de printer, zoals hieronder is afgebeeld. Zie ook Een printkopreiniger plaatsen.
1. Plaats elke printkopreiniger in de juiste sleuf van het servicestation, in de richting die wordt aangegeven door de pijl. 2. Nadat u de printkopreiniger volledig in de sleuf hebt gedrukt, drukt u deze naar binnen en naar beneden (zoals wordt aangegeven door de pijl) tot de reiniger vastklikt. Als u problemen ondervindt, gaat u naar Ik kan geen printkopreiniger plaatsen. Opmerking De nieuwe printkopreiniger wordt pas op het voorpaneel weergegeven nadat de deur aan de rechterkant is gesloten.
3. Sluit de deur nadat u de printkopreiniger(s) in de printer hebt geplaatst. Opmerking Alle inktpatronen, printkoppen en printkopreinigers moeten in de printer zijn geïnstalleerd voordat deze kan verdergaan. 4. Als er geen papier is geladen, geeft het voorpaneel aan dat u dit moet doen. Telkens wanneer u een nieuwe printkop en reiniger plaatst, voert de printer normaal gesproken een uitlijning van de printkoppen en kleurkalibratie uit.
De pagina Supplies (Benodigdheden) bevat de status van de inktpatronen (inclusief het inktniveau), de printkoppen, de printkopreinigers en het geladen papier. Statistische informatie over de inktpatronen weergeven Zo geeft u informatie weer over de inktpatronen: 1. Selecteer het pictogram 2. Kies Ink cartridge information (Informatie over inktpatronen) en selecteer de patroon waarover u informatie wenst. 3. Op het voorpaneel verschijnt het volgende: op het voorpaneel.
Statistische informatie over de inktkoppen weergeven Zo geeft u informatie weer over de printkoppen: 1. Selecteer het pictogram 2. Kies Printhead information (Informatie over printkoppen) en selecteer de printkop waarover u informatie wenst. 3. Op het voorpaneel verschijnt het volgende: op het voorpaneel.
214 Hoofdstuk 11 Hoe...
12 Hoe...
Telgegevens opvragen van de printer Er zijn verschillende manieren waarop u telgegevens kunt opvragen van uw printer. ● Statistische informatie over het gebruik van de printer weergeven voor de hele levensduur van de printer, of voor bepaalde perioden. Zie Statistische informatie over het gebruik van de printer weergeven. ● Informatie over het inkt- en papierverbruik weergeven voor elk van uw recente taken met de geïntegreerde webserver of via het voorpaneel van de printer.
Telgegevens aanvragen per e-mail 1. Controleer of de datum en tijd van de printer correct zijn ingesteld. Zie Datum en tijd instellen. 2. Controleer op het tabblad Settings (Instellingen) ook of de e-mailserver correct is ingesteld. 3. Selecteer Device setup (Apparaatconfiguratie) op het tabblad Settings (Instellingen) en kies Settings (Instellingen) in het deelvenster Accounting (Telgegevens).
● C: Kaarten en renderings met lage bedekking (2 tot 5 ml/m²) ● D: Foto's (meer dan 5 ml/m²) U kunt een Excel-sjabloon downloaden van HP Designjet Online (http://www.hp.com/go/designjet/), waarmee u de XML-gegevens kunt weergeven in een werkblad zodat deze beter leesbaar zijn. Dankzij de analyse van de telgegevens kunt u klanten exact en flexibel factureren voor het gebruik van uw printer.
13 Hoe...
De buitenkant van de printer reinigen Reinig wanneer nodig de buitenkant van de printer en alle overige delen die u regelmatig aanraakt tijdens het normale gebruik van de printer (zoals de handgrepen van de inktpatroonlade), met een vochtige spons of een zachte doek en een mild schoonmaakmiddel zoals niet-agressieve vloeibare zeep. WAARSCHUWING Voorkom elektrische schokken door de printer uit te schakelen en het netsnoer uit het stopcontact te halen voordat u deze reinigt.
De plaat reinigen Reinig de plaat van de printer regelmatig, elke paar maanden of wanneer nodig. Opmerking Als u op breed papier afdrukt nadat u een tijdje op smaller papier hebt afgedrukt, is mogelijk de linkerkant van de plaat vuil geworden. Als u dit vuil niet verwijdert, blijven er vlekken achter op de achterkant van het papier. U reinigt de plaat als volgt: NLWW 1. Verwijder al het papier uit de printer. 2. Open het venster. 3.
Met deze opdracht laat u de kleine rollen op de plaat draaien, zodat de rollen aan alle kanten kunnen worden gereinigd. Opmerking Als u met de HP Designjet 4000-printer werkt en u merkt dat deze opdracht niet beschikbaar is, kunt u de nieuwste firmwareversie downloaden (zie De firmware van de printer bijwerken). Deze is beschikbaar in het voorjaar van 2006. 6. Gebruik een schone, absorberende, pluisvrije, in isopropylalcohol gedrenkte doek om de plaat schoon te vegen en losse inktresten te verwijderen.
De printkopwagen smeren Ongeveer één keer per jaar moet de printkopwagen worden gesmeerd om te zorgen dat deze makkelijk over de stang blijft schuiven. 1. op het voorpaneel van de printer Als u toegang wilt tot de wagen, selecteert u het pictogram en kiest u Printheads management (Printkopbeheer) > Replace printheads now (Printkoppen nu vervangen). De wagen schuift naar het midden van de printer.
De handmatige papiersnijders vervangen Het is niet waarschijnlijk dat u de papiersnijders moet vervangen, tenzij u hiermee veel zwaar papier snijdt. Toch bevat elke snijder een reservesnijblad. Als u merkt dat een snijder niet meer goed snijdt, vervangt u het blad als volgt: 1. Houd in eerste instantie de snijder in zijn normale positie aan de rechterzijde van de lade. 2. Verwijder de schroef van de onderkant van de snijder. Houd de onderplaat vast om te voorkomen dat deze valt. 3.
De firmware van de printer bijwerken De functies van de printer worden bestuurd door software in de printer. Deze software wordt ook firmware genoemd. Van tijd tot tijd stelt Hewlett-Packard firmware-updates beschikbaar. Deze updates verhogen de functionaliteit van de printer en breiden de voorzieningen uit die de printer al biedt.
226 Hoofdstuk 13 Hoe...
14 Hoe...
De Image Diagnostics Print (Beelddiagnoseafdruk) afdrukken De Image Diagnostics Print (Beelddiagnoseafdruk) bestaat uit patronen die zijn ontworpen om problemen met de afdrukkwaliteit aan te geven. Deze afdruk helpt u te controleren of er geen probleem is met de afdrukkwaliteit. Als dat toch het geval is, geeft de afdruk aan wat de oorzaak is en hoe u het probleem kunt verhelpen.
Als deel 2 geen enkel probleem aangeeft, moet u deel 3 negeren. Deel 1 van de Image Diagnostics Print (Beelddiagnoseafdruk) interpreteren Het doel van deel 1 is het identificeren van problemen met de kleuruitlijning en de bidirectionele uitlijning.
Oplossing 1. Lijn wanneer mogelijk de printkoppen uit met behulp van hetzelfde papiertype als bij de detectie van de onaanvaardbare afdrukkwaliteit. Dit is echter niet altijd mogelijk omdat sommige papiertypen niet geschikt zijn voor het uitlijnen van printkoppen. Zie De printkoppen uitlijnen. 2. Als de afdrukkwaliteit niet verbetert, neemt u contact op met een Service Partner.
of donkere strepen: of een meer geleidelijk, golvend effect: Horizontale strepen over stroken van één enkele kleur Als een printkop defect is, ziet u horizontale strepen over stroken van één enkele kleur, of de horizontale stroken zijn in elk geval veel duidelijker in één kleur dan in de overige kleuren. Opmerking Streepvorming in de groene stroken is moeilijker te zien en wordt mogelijk veroorzaakt door een gele of een cyaan printkop.
3. Druk de Image Diagnostics Print (Beelddiagnoseafdruk) opnieuw af. Als u nog altijd streepvorming ziet, gaat u door naar stap 4 en 5. 4. Aangezien er twee printkoppen per kleur zijn, moet u in deel 3 van de Image Diagnostics Print (Beelddiagnoseafdruk) goed controleren welke printkop het probleem veroorzaakt. Zie Deel 3 van de Image Diagnostics Print (Beelddiagnoseafdruk) interpreteren Deel 3. 5. Vervang de printkop die het probleem veroorzaakt. Zie Een printkop verwijderen en Een printkop plaatsen.
In de eerste twee van deze voorbeelden ontbreken er zo veel lijnen dat mogelijk de printkop defect is. In het derde geval ontbreken er maar enkele lijnen. Dit is acceptabel omdat de printer kan compenseren, zodat deze kleine problemen niet zichtbaar zijn. Oplossing Als deel 3 een probleem met één printkop aangeeft maar deel 2 geen probleem aangeeft, hoeft u niet onmiddellijk iets te doen omdat de printer kan compenseren, zodat het probleem niet zichtbaar is en de afdrukkwaliteit behouden blijft.
234 Hoofdstuk 14 Hoe...
15 Hoe... (onderwerpen over het kalibreren van het papierdoorvoermechanisme) De printer is in de fabriek gekalibreerd om te garanderen dat het papier correct wordt doorgevoerd bij gebruik van ondersteunde papiertypen in normale omgevingsomstandigheden.
Overzicht van kalibreren 1. Gebruik het voorpaneel om een gekleurd patroon dat in de printer is opgeslagen, zeven keer af te drukken, elke keer met een andere papierdoorvoerinstelling. 2. Bepaal welk patroon het best is afgedrukt. 3. Gebruik het voorpaneel om het beste patroon op te geven en zo in te stellen welke papierdoorvoerinstelling voor de volgende afdruktaken wordt gebruikt.
Stap 5. Selecteer Print Patterns (Patronen afdrukken). De printer drukt een aantal genummerde patronen af (van 1 tot 7), die er alle ongeveer als volgt uitzien als u Drawings/text (Tekeningen/tekst) hebt geselecteerd: of als volgt als u Images (Afbeeldingen) hebt geselecteerd: Het afdrukken met de optie Optim. drawings/text (Optimaliseren voor tekeningen/tekst) duurt ongeveer drie minuten. Met de optie Optimize for images (Optimaliseren voor afbeeldingen) duurt dit ongeveer vijf minuten.
Als u niet goed het beste patroon kunt identificeren, kunnen de volgende scenariobeschrijvingen u helpen. ● Als maar één patroon duidelijk het beste is en de patronen boven en onder dit patroon lichte/ donkere strepen bevatten, selecteert u dit patroon. ● Als u twee patronen zonder streepvorming naast elkaar ziet (zie hieronder), gebruikt u de patronen boven en onder deze twee patronen om u te helpen bij het selecteren.
Het kalibreren is nu voltooid. Na het kalibreren Als het kalibreren het probleem met de afdrukkwaliteit heeft verminderd maar niet volledig heeft verholpen, voert u stap 7 nogmaals uit en selecteert u een ander nummer. Als u lichtere strepen ziet, selecteert u een lager nummer dan uw oorspronkelijke selectie. Ziet u donkerdere strepen, dan selecteert u een hoger nummer.
240 Hoofdstuk 15 Hoe...
16 Hoe... (onderwerpen over de scanner) [4500] Opmerking NLWW Dit hoofdstuk is alleen van toepassing op de HP Designjet 4500-printerserie.
De scanner kalibreren Voor het behoud van de beste scankwaliteit moet u de scanner één keer per maand opnieuw kalibreren. 1. Voordat u kalibreert, leest u de on-line handleiding bij de scanner voor informatie over hoe u het scangebied reinigt. Vervolgens schakelt u de scanner uit en reinigt u het scangebied. Als het scangebied niet schoon is, wordt niet goed gekalibreerd. 2.
Een nieuw mediaprofiel maken De scanner moet zijn gekalibreerd (zie De scanner kalibreren) en het juiste papiertype moet zijn geladen voordat u deze procedure start. 1. Selecteer het tabblad Setup. 2. Als de juiste printer nog niet is geselecteerd, drukt u op de knop Printer om de printer te selecteren. 3. Druk op de knop Media Profile (Mediaprofiel). Er wordt een lijst met bestaande mediaprofielen weergegeven. Als een van deze mediaprofielen momenteel is geselecteerd, wordt het grijs weergegeven.
4. Selecteer de type-origineel-sjabloon. a. Druk op de knop Type of original (Type origineel) op het tabblad Copy (Kopiëren). b. Als u de instellingen van deze opties wilt wijzigen of een nieuwe optie wilt maken, drukt u op de knop Extra. c. 5. Selecteer de type-origineel-sjabloon die het best de huidige invoer beschrijft. Selecteer het invoerformaat. a. Druk op de knop Input size (Invoerformaat) op het tabblad Copy (Kopiëren). b.
6. Selecteer het uitvoerformaat. a. Druk op de knop Output size (Uitvoerformaat) op het tabblad Copy (Kopiëren). b. Als u de instellingen van deze opties wilt wijzigen of een nieuwe optie wilt maken, drukt u op de knop Extra. c. Selecteer het formaat van de uit te voeren kopie in de lijst.
Een document naar een bestand scannen 1. Selecteer het tabblad Scan (Scannen) en stel de scanopties in, zoals het type origineel, het formaat, de bestandsnaam, enzovoort. Als u de bestandsindeling (TIFF, JPEG) wilt instellen, drukt u op de knop Settings (Instellingen), zodat het dialoogvenster Scan Settings (Scaninstellingen) wordt weergegeven. Opties zoals marges, indeling en mediaprofiel kunnen later op het tabblad Setup worden ingesteld voordat u afdrukt vanaf het bestand. 2.
Een bestand afdrukken Het afdrukken van uw bestanden wordt geconfigureerd en beheerd via een handige afdruklijst. U kunt het aantal exemplaren instellen door het aantal voor elk bestand afzonderlijk in te stellen, het aantal sets te bepalen (het aantal keer dat de volledige lijst wordt afgedrukt) of een combinatie van beide te gebruiken. 1. Als u nog geen mediaprofiel hebt voor het type papier waarop u wilt afdrukken, moet u een profiel maken. Zie Een nieuw mediaprofiel maken. 2.
Op extra zwaar papier of karton scannen De scanner kan extra zwaar papier met coating en karton scannen. WAARSCHUWING Andere dikke materialen worden niet ondersteund en kunnen de scanner beschadigen. Verwijder nietjes en andere schurende bevestigingen vóór het scannen. 1. Druk op de toets Automatische dikteregeling op het bedieningspaneel van de scanner. 2. Houd de toets Pijl-omhoog ingedrukt om de hoogte van de invoersleuf te vergroten tot er voldoende ruimte is om het document in de sleuf te schuiven.
3. Druk op de knop Setup in het dialoogvenster Scanner. 4. Selecteer het tabblad Extended Thickness (Uitgebreide dikte) en schakel het selectievakje Use extended thickness paper handling (Uitgebreide diktebehandeling) in. 5. Wijzig de waarde voor elke scannercamera. Doorgaans worden alleen positieve waarden gebruikt. 6. Maak testscans en pas de waarden aan tot de lijnen correct worden gestikt. 7. Druk op OK om de instellingen te accepteren.
Volledig zoomen Bij het instellen van het formaat en de marges moet u de hele afbeelding kunnen zien. Pas het formaat van de afbeelding zo aan dat deze volledig in het voorbeeldvenster past. Inzoomen De as voor het inzoomen bevindt zich in het midden van het voorbeeldvenster. Druk op de knop Inzoomen tot het gewenste detailniveau is bereikt. Uitzoomen De as voor het uitzoomen bevindt zich in het midden van het voorbeeldvenster. Druk op de knop Uitzoomen tot het gewenste detailniveau is bereikt.
Functie Verplaatsen Verplaats de afbeelding om een willekeurig deel te centreren of zichtbaar te maken in het voorbeeldvenster. U kunt de afbeelding op twee manieren verplaatsen: ● door naar een willekeurige plaats in het afbeeldingsvenster te slepen; ● door een punt op het scherm aan te raken om dat punt te centreren in het voorbeeldvenster. Papierframe positioneren U kunt het papierframe direct in het voorbeeld positioneren en de kopieerzone visueel instellen.
Het origineel wordt scheef weergegeven in het voorbeeldvenster. U hoeft het origineel niet opnieuw te laden. Druk op de uitlijnknoppen om de afbeelding uit te lijnen op het papierframe. U kunt ook op de knop Settings (Instellingen) op het tabblad Copy (Kopiëren) of Scan (Scannen) drukken, en de optie Auto-align (Automatisch uitlijnen) kiezen. Hierdoor wordt de afbeelding automatisch uitgelijnd.
2. Druk op de knop System (Systeem). 3. Klik op de knop met de naam van de printer die u wilt toevoegen. 4. Volg de instructies op het scherm. Bestanden opslaan op een cd of dvd Met de HP Designjet naar cd of dvd schrijven is even gemakkelijk als naar een ander opslagmedium schrijven. 1. Plaats een lege cd of dvd in het cd/dvd-station van het touch-screen. U kunt ook naar een gedeeltelijk beschreven cd of dvd schrijven als deze nog niet is afgesloten. 2.
Als u over het netwerk een verbinding tot stand wilt brengen, moet u over het IP-adres van uw scannersysteem beschikken. U kunt dit adres als volgt weergeven via het touch-screen: 1. Druk op het touch-screen op het tabblad Setup. 2. Druk op de knop Options (Opties) op het tabblad Setup. 3. Druk op de knop General (Algemeen) in het dialoogvenster Options (Opties). 4. Druk op de knop About (Informatie over) in het dialoogvenster General (Algemeen). 5.
4. Typ in het venster Webmap toevoegen http://scanner_ip/images, waarbij scanner_ip staat voor het IP-adres van het scannersysteem, en klik vervolgens op Volgende. 5. Voer een naam in waarmee u op deze computer naar de map verwijst en klik vervolgens op Voltooien. Als u de gedeelde map wilt openen, dubbelklikt u op Deze computer en vervolgens dubbelklikt u op Webmappen. De nieuwe map wordt daarna weergegeven in het venster Webmappen.
3. Druk als dat nodig is op de knop Tool 4. (Extra). In het dialoogvenster Accounting (Telgegevens): ● Druk op de knop Delete (Verwijderen) om de huidige account te verwijderen (de account waarvan de naam in het dialoogvenster wordt weergegeven). ● Druk op de knop New (Nieuw) om een nieuwe account te maken en typ vervolgens een naam voor de nieuwe account. De nieuwe account wordt automatisch de huidige account. ● Druk op de knop Rename (Naam wijzigen) om de naam van de huidige account te wijzigen.
3. Houd beide hendelknoppen ingedrukt, plaats uw vrije vingers in de invoersleuf en klap het deksel van het scangebied open. Het scangebied kan vervolgens worden gereinigd. 4. Veeg de glasplaat voorzichtig schoon met een pluisvrije doek die is gedrenkt in een niet-agressieve glasreiniger die reinigt zonder strepen achter te laten. VOORZICHTIG Gebruik geen schuurmiddelen, aceton, benzeen of vloeistoffen die dergelijke chemicaliën bevatten.
258 Hoofdstuk 16 Hoe...
17 Het probleem is...
Het lukt niet om het papier te laden [4000] Opmerking Dit onderwerp is alleen van toepassing op de HP Designjet 4000-printerserie. ● Mogelijk wordt het papier onder een hoek (schuin of foutief geplaatst) ingevoerd. Controleer of de rechterrand van het papier is uitgelijnd op de halve cirkel aan de rechterkant van de plaat, en met name als u losse vellen gebruikt, of de bovenrand is uitgelijnd op de metalen staaf in de plaat.
Voorpaneelmelding Aanbevolen actie Paper too big (Papier te groot) Tijdens het laden van het papier heeft de printer vastgesteld dat het papier te breed of te lang (alleen losse vellen) is om correct te worden geladen. Druk op de toets Annuleren om het laden te stoppen. Zie Functionele specificaties. Sheet too long (Vel te lang) Tijdens het laden heeft de printer vastgesteld dat het vel te lang is om correct te worden geladen. Controleer of de printer losse vellen en geen rol verwacht.
Een papierstoring (papier zit vast in printer) [4000] Opmerking Dit onderwerp is alleen van toepassing op de HP Designjet 4000-printerserie. Wanneer een papierstoring optreedt, verschijnt doorgaans de melding Possible paper jam (Mogelijke papierstoring) op het voorpaneel, evenals een van de volgende twee foutcodes: ● 81:01 geeft aan dat het papier niet in de printer kan worden gevoerd. ● 86:01 geeft aan dat de printkopwagen niet tussen beide uiteinden kan worden verplaatst.
3. Probeer de printkopwagen opzij te schuiven. 4. Zet de papierladingshendel zo ver mogelijk omhoog. 5. Verwijder voorzichtig al het vastgelopen papier dat u via de bovenkant van de printer kunt lostrekken. 6. Trek de rest van de rol of het vel voorzichtig omlaag uit de printer. 7. Zet de printer aan. 8. Laad de rol opnieuw of plaats een nieuw vel. Zie Een rol in de printer plaatsen [4000] of Eén vel plaatsen [4000]. 9.
Papierpad controleren ● Dit probleem kan optreden wanneer een rol op is en het einde van de rol aan de kartonnen kern kleeft. Als dit het geval is, snijdt u het einde van de rol van de kern. Normaal gesproken kunt u vervolgens het papier in de printer voeren en verwijderen, en een nieuwe rol plaatsen. ● Als u dat niet kunt, voert u de procedure uit die hierboven is beschreven onder Controleer het printkoppad.
NLWW 3. Open het venster. 4. Zet de aandrijvingshendel zo ver mogelijk omhoog. 5. Zet de papierladingshendel van rol 1 omhoog.
266 6. Zet de papierladingshendel van rol 2 omhoog. 7. Til de onderste lade enigszins omhoog en trek deze vervolgens zo ver mogelijk naar u toe. 8. Snijd het papier af. Hoofdstuk 17 Het probleem is...
9. Verwijder de rol. 10. Til de bovenste lade enigszins omhoog en trek deze vervolgens zo ver mogelijk naar u toe. 11. Snijd het papier af.
12. Verwijder de rol. 13. Zet de linkervergrendelingshendel omlaag. 14. Zet de rechtervergrendelingshendel omlaag. 268 Hoofdstuk 17 Het probleem is...
15. Trek het voorpad zo ver mogelijk naar u toe. 16. Probeer de printkopwagen opzij te schuiven.
17. Verwijder voorzichtig al het vastgelopen papier dat u via de bovenkant van de printer kunt lostrekken. 18. Druk het papier via de plaat naar binnen. 19. Trek de rest van het papier voorzichtig omlaag uit de printer. Controleer of er losse stukken papier in het papierpad zijn achtergebleven. 270 Hoofdstuk 17 Het probleem is...
20. Duw het voorpad weer op zijn plaats. 21. Zet de linkervergrendelingshendel omhoog. 22. Zet de rechtervergrendelingshendel omhoog.
23. Duw de bovenste lade weer op zijn plaats. 24. Duw de onderste lade weer op zijn plaats. 25. Zet de aandrijvingshendel omlaag. 272 Hoofdstuk 17 Het probleem is...
26. Zet de papierladingshendel van rol 1 omlaag. 27. Zet de papierladingshendel van rol 2 omlaag. 28. Sluit het venster. 29. Zet de printer aan. 30. Hang de rollen weer op hun plaats. Zie Een rol in de printer plaatsen [4500]. Als het papierpad nog altijd wordt geblokkeerd door vastgelopen papier, kunt u dit vaak verhelpen door een stevig papiertype in de printer te laden. 31. Bevestig de opvangbak of de stapelaar weer aan de printer. 32.
Papierpad controleren ● Dit probleem kan optreden wanneer een rol op is en het einde van de rol aan de kartonnen kern kleeft. Als dit het geval is, snijdt u het einde van de rol van de kern. Normaal gesproken kunt u vervolgens het papier in de printer voeren en verwijderen, en een nieuwe rol plaatsen. ● Als u dat niet kunt, voert u de procedure uit die hierboven is beschreven onder Controleer het printkoppad.
NLWW 3. Open het venster. 4. Zet de aandrijvingshendel zo ver mogelijk omhoog. 5. Zet de papierladingshendel van rol 2 omhoog.
276 6. Til de onderste lade enigszins omhoog en trek deze vervolgens zo ver mogelijk naar u toe. 7. Snijd het papier af. 8. Verwijder de rol. Hoofdstuk 17 Het probleem is...
9. Til de bovenste lade enigszins omhoog en trek deze vervolgens zo ver mogelijk naar u toe. 10. Verwijder voorzichtig het afgesneden onderste gedeelte van het papier. 11. Verwijder voorzichtig al het papier dat u via de bovenkant van de printer kunt lostrekken.
12. Controleer de voorzijde van de rolmodule, achter de laden. 13. Verwijder eventueel zichtbaar papier. 14. Verwijder papier dat vastzit tussen de rol en de kleine plastic rollen. 15. Zoek aan de achterkant van de printer de drie verticale openingen aan de achterzijde van de rolmodule. 278 Hoofdstuk 17 Het probleem is...
16. Als er door de openingen papier zichtbaar is, probeert u dit te verwijderen door het papier naar boven of naar beneden te duwen. 17. Duw aan de voorzijde van de printer de bovenste lade terug op zijn plaats. 18. Duw de onderste lade weer op zijn plaats.
19. Zet de aandrijvingshendel omlaag. 20. Zet de papierladingshendel van rol 2 omlaag. 21. Sluit het venster. 22. Zet de printer aan. 23. Hang de rollen weer op hun plaats. Zie Een rol in de printer plaatsen [4500]. Als het papierpad nog altijd wordt geblokkeerd door vastgelopen papier, kunt u dit vaak verhelpen door een stevig papiertype in de printer te laden. 24. Bevestig de opvangbak of de stapelaar weer aan de printer. 25.
De afdrukken worden niet op de juiste wijze in de bak gestapeld [4000] Opmerking Dit onderwerp is alleen van toepassing op de HP Designjet 4000-printerserie. ● Zet de drie lusstoppers omhoog als u afdrukt op kleine vellen. ● Papier op het einde van de rol kan makkelijk gaan krullen en zo problemen met het stapelen veroorzaken. Plaats een nieuwe rol, of verwijder elke afdruk handmatig zodra deze is voltooid.
Het kan gebeuren dat een rol automatisch wordt verwijderd of afgesneden als deze een aantal dagen niet is gebruikt. Zo wordt ervoor gezorgd dat het papier in een zo goed mogelijke conditie blijft. Dit gebeurt alleen bij bepaalde papiersoorten (glanzend papier en zwaar papier met coating). De printer verwijdert het papier terwijl de printer is uitgeschakeld [4500] Opmerking Dit onderwerp is alleen van toepassing op de HP Designjet 4500-printerserie.
18 Het probleem is...
Algemeen advies Wanneer u problemen hebt met de afdrukkwaliteit, doet u het volgende: ● Voor de beste printerprestaties mag u alleen originele benodigdheden en accessoires van de fabrikant gebruiken, waarvan de betrouwbaarheid en prestaties grondig zijn getest voor probleemloos afdrukken en de hoogst mogelijke kwaliteit. Zie Ondersteunde papiertypen selecteren voor informatie over aanbevolen papiertypen.
3. U wordt aangeraden een zwaarder papiertype te gebruiken, zoals extra zwaar HP Papier met Coating of HP Productivity Glanzend Fotopapier, wanneer u vaste kleuren afdrukt. 4. Als het probleem niet is opgelost, gebruikt u de Image Diagnostics Print (Beelddiagnoseafdruk) voor meer informatie over de oorzaak van het probleem. Zie Hoe... (Onderwerpen over Image Diagnostics Print (Beelddiagnoseafdruk)). Lijnen die ontbreken of dunner zijn dan verwacht 1.
Voor elke situatie geldt de volgende aanbevolen procedure: 1. Reinig de elektrische contacten van de printkop die verantwoordelijk lijkt voor het probleem (in dit voorbeeld de magenta printkop). Zie De elektrische contacten van een printkop reinigen. 2. Reinig de printkoppen. Zie De printkoppen herstellen (reinigen). 3. Druk de afbeelding opnieuw af met dezelfde instellingen als daarvóór. 4. Als het probleem niet is opgelost, vervangt u de printkop die verantwoordelijk lijkt voor het probleem.
Het papier is niet plat Als het papier niet plat is maar ondiepe golven heeft wanneer het uit de printer komt, vertoont de afgedrukte afbeelding wellicht zichtbare defecten, zoals verticale strepen. Dit probleem kan zich voordoen wanneer u dun papier gebruikt dat verzadigd is door inkt. U wordt aangeraden een zwaarder papiertype te gebruiken, zoals extra zwaar HP Papier met Coating of HP Productivity Glanzend Fotopapier, wanneer u vaste kleuren afdrukt.
Vlekken op de voorkant van papier met coating Als veel inkt wordt gebruikt op papier met coating, absorbeert het papier de inkt snel en zet het uit. Wanneer de printkoppen over het papier schuiven, raken ze het papier en maken ze vlekken op de afgedrukte afbeelding. Als u dit probleem detecteert, moet u de afdruktaak onmiddellijk annuleren. Druk op de toets Annuleren en annuleer de taak ook vanuit de computertoepassing. Als u dat niet doet, kan het doordrenkte papier de printkoppen beschadigen.
Een defect bij het begin van de afdruk Er is een type defect dat alleen optreedt bij het begin van een afdruk, binnen 5,5 cm van de bovenrand van het papier. Mogelijk ziet u een dunne of dikke strook inconsistente kleur: Zo voorkomt u dit probleem: 1. De eenvoudigste oplossing is de optie Extended Margins (Uitgebreide marges) te selecteren in het stuurprogramma, in de geïntegreerde webserver of op het voorpaneel.
De lijnen zijn dubbel of niet in de juiste kleur afgedrukt Dit probleem kan verschillende zichtbare symptomen hebben: ● Gekleurde lijnen worden dubbel, in verschillende kleuren afgedrukt. ● De randen van gekleurde blokken hebben niet de juiste kleur. Zo verhelpt u dit type probleem: 1. Lijn de printkoppen uit. Zie De printkoppen uitlijnen. 2. Controleer of u geschikte instellingen voor de afdrukkwaliteit gebruikt. Zie Instellingen voor de afdrukkwaliteit selecteren.
1. Controleer of u geschikte instellingen voor de afdrukkwaliteit gebruikt. Zie Instellingen voor de afdrukkwaliteit selecteren. 2. Verticale lijnen worden doorgaans beter afgedrukt op rolpapier dan op losse vellen. Als u losse vellen moet gebruiken, stelt u de afdrukkwaliteit in op Best. 3. U wordt aangeraden een zwaarder papiertype te gebruiken, zoals extra zwaar HP Papier met Coating of HP Productivity Glanzend Fotopapier. Zie Instellingen voor de afdrukkwaliteit selecteren. 4.
Nauwkeurigheid van kleuren Er zijn twee basisvereisten om nauwkeurige kleuren af te drukken: 1. Zorg dat het papiertype is gekalibreerd zodat alle afdrukken en alle printers dezelfde resultaten opleveren. Zie Kleurkalibratie uitvoeren. 2. Selecteer geschikte opties in uw toepassing: zie Hoe... (onderwerpen over kleur).
PANTONE-kleuren handmatig converteren Als uw printer geen ondersteuning biedt voor PostScript of als u een toepassing gebruikt die de naam van de PANTONE-kleur niet naar de printer verzendt (zoals Adobe Photoshop), kunt u Automatic PANTONE Calibration niet gebruiken. In dat geval kunt u desgewenst elke PANTONE-kleur handmatig in de toepassing converteren naar CMYK-waarden, met behulp van tabellen die specifiek voor uw printer en het door u gebruikte papiertype zijn gegenereerd.
4. Plaats in beide printers ongeveer hetzelfde papiertype. 5. Zorg dat de instelling van Paper Type (Papiertype) op het voorpaneel overeenkomt met het papier dat u hebt geplaatst. 6. Druk de afbeelding op de HP Designjet 1000 af met behulp van de normale instellingen. 7. U gaat nu dezelfde afbeelding afdrukken op de HP Designjet 4000. 8.
Hetzelfde HP-GL/2-bestand afdrukken U hebt een HP-GL/2-bestand gegenereerd (wordt ook PLT-bestand genoemd) met behulp van het HPGL/2-stuurprogramma dat voor de ene printer is geïnstalleerd, maar u wilt hetzelfde bestand naar beide printers verzenden. 1. Zorg dat op beide printers de meest recente firmware is geïnstalleerd. Zie De firmware van de printer bijwerken. 2. op het Zorg dat Color Calibration (Kleurkalibratie) is ingeschakeld.
296 Hoofdstuk 18 Het probleem is...
19 Het probleem is...
De afdruk is volledig leeg Als de instelling voor de grafische taal op het voorpaneel Automatic (Automatisch) is (de standaardinstelling), probeert u de andere instellingen: PostScript voor een PostScript-bestand, HPGL/2 voor een HP-GL/2-bestand, enzovoort (zie De instelling voor de grafische taal wijzigen). Vervolgens verzendt u het bestand opnieuw. Wanneer u klaar bent met deze afdruk, zet u de grafische taal weer op Automatic (Automatisch).
● Controleer of de afdrukstand van het papier overeenkomt met de stand die door de software wordt toegepast. Met de optie Printing defaults menu (Menu standaard afdrukinstellingen) > Paper options (Papieropties) > Rotate (Roteren) op het voorpaneel wijzigt u zowel de afdrukstand van een afdruk als die van de pagina. Mogelijk wordt een geroteerde afbeelding op een rol enigszins afgesneden om het juiste paginaformaat te behouden.
De afdruk is vervormd of onleesbaar ● Mogelijk is er een probleem met de interfacekabel tussen de printer en het netwerk (of uw computer). Probeer het probleem op te lossen door een andere kabel te gebruiken. ● Als de instelling voor de grafische taal op het voorpaneel Automatic (Automatisch) is (de standaardinstelling), probeert u de andere instellingen: PostScript voor een PostScriptbestand, HP-GL/2 voor een HP-GL/2-bestand, enzovoorts (zie De instelling voor de grafische taal wijzigen).
het ontbreken van sommige objecten in de uitvoer tot gevolg hebben. Hierna volgt voor dergelijke gevallen een aantal aanbevelingen voor het gebruik van het HP-GL/2-stuurprogramma voor Windows. ● Selecteer Document options (Documentopties) op het tabblad Advanced (Geavanceerd), selecteer vervolgens Printer features (Functies van printer) en stel Send Job as Raster (Taak verzenden als raster) in op Enabled (Ingeschakeld).
302 Hoofdstuk 19 Het probleem is...
20 Het probleem is...
Ik kan geen inktpatroon plaatsen 1. Controleer of u het juiste type patroon hebt (modelnummer). 2. Controleer of de kleur van het etiket op de patroon overeenkomt met de kleur van het etiket op de sleuf. 3. Controleer of u de patroon in de juiste richting plaatst (het gekleurde etiket moet zich bovenaan bevinden). VOORZICHTIG Maak nooit de binnenkant van de inktpatroonsleuven schoon.
De voorpaneelmelding Reseat (Installeer opnieuw) of Replace (Vervang) voor de printkoppen verdwijnt niet 1. Verwijder de printkop en controleer of de beschermtape is verwijderd. 2. Probeer het probleem op te lossen door de elektrische contacten tussen de printkop en de wagen te reinigen. Zie De elektrische contacten van een printkop reinigen. 3. Plaats de printkop weer in de wagen en controleer of de voorpaneelmelding is verdwenen. 4. Als het probleem niet is opgelost, plaatst u een nieuwe printkop.
Statusberichten voor printkopreinigers De volgende statusberichten voor printkopreinigers kunnen verschijnen: ● OK: de printkopreiniger werkt normaal, er treden geen bekende problemen op.
21 Het probleem is... (onderwerpen over de stapelaar) [4500] Opmerking NLWW Dit hoofdstuk is alleen van toepassing op de HP Designjet 4500-printerserie.
Omkrullend papier Wanneer u in de modus Fast (Snel) afdrukt op sterk krullend papier, kan het papier omkrullen wanneer het wordt uitgeworpen in het stapelaarplateau. Om dit probleem te voorkomen raden wij u aan over te schakelen op de modus Normal (Normaal), of een rol papier met een kern van 7,5 cm (3 inch) te gebruiken. De onderrand van het papier krult omhoog Gebruik de instelling Optimize for images (Optimaliseren voor afbeeldingen): zie Een andere afdrukkwaliteit instellen.
22 Het probleem is... (onderwerpen over de scanner) [4500] Opmerking Dit hoofdstuk is alleen van toepassing op de HP Designjet 4500-printerserie. Als er andere scannerproblemen optreden dan de problemen die hieronder worden beschreven, raadpleegt u de on-line handleiding bij de scanner voor meer informatie.
Het diagnoselampje knippert Wellicht moet het scangebied worden gereinigd. Voer de procedures voor routineonderhoud uit die in de on-line handleiding worden beschreven, zoals het reinigen. Start de scanner opnieuw op nadat u de onderhoudsprocedures hebt uitgevoerd. Als het lampje blijft knipperen, zijn er mogelijk problemen met de cameraposities. Als dat het geval is, neemt u contact op met HP Support. Het wachtlampje knippert Dit geeft aan dat de scanner aanpassingen moet uitvoeren maar dit niet kan.
Op de scanner wordt een waarschuwingsbericht weergegeven Onder bepaalde omstandigheden kan de scanner aangeven dat er onderhoud moeten worden uitgevoerd. ● Scanner Maintenance has not been run for 30 days (Scanneronderhoud is al 30 dagen niet uitgevoerd). ● Lamp quality fails. The filter should be replaced at the same time. (Lamp is niet goed. Tegelijkertijd moet het filter worden vervangen.) ● Glass plate quality fails. (Glasplaat is niet goed.) ● Original background quality fails.
6. Nadat u de drie doelen hebt aangeraakt, wordt u gevraagd om een willekeurig gedeelte van het touch-screen aan te raken. Als u tevreden bent met het resultaat van de kalibratie, drukt u op de knop Yes (Ja). Als u wordt gevraagd of u het systeem opnieuw wilt opstarten, drukt u op No (Nee). 7. Het scherm waarin u de taal kunt selecteren, wordt weergegeven. Selecteer de taal die u wilt gebruiken voor de Designjet Scan-toepassing.
23 Het probleem is...
De opstartprocedure van de printer wordt niet volledig uitgevoerd Als de opstartprocedure van de printer stopt wanneer het nummer 17 op het voorpaneel staat, is er een probleem met het bestandssysteem op de vaste schijf van de printer. De printer controleert het hele bestandssysteem en brengt de nodige correcties aan. Dit probleem kan optreden na een stroomonderbreking met ingeschakelde printer of bij een fysiek probleem met de vaste schijf.
Code Korte melding Aanbevolen actie plaatsen. Als het probleem hierdoor niet is opgelost, neemt u contact op met een Service Partner. NLWW 26.3:01 Reseat cyan cartridge (Installeer cyaan patroon opnieuw) De cyaan patroon wordt niet gedetecteerd. Installeer deze opnieuw. Zie Een inktpatroon verwijderen en Een inktpatroon plaatsen. Als het probleem hierdoor niet is opgelost, neemt u contact op met een Service Partner. 27:03 Restart the printer. If problem persists, call HP support.
Code Korte melding Aanbevolen actie 66:08 Please resubmit the job as the paper type has changed. (Het papiertype is gewijzigd. Verzend de taak opnieuw.) Het papiertype is gewijzigd sinds de taak is verzonden. De taak kan niet worden afgedrukt op het papier dat is geladen. Verzend de taak opnieuw of laad ander papier. 71:03 Restart the printer. If problem persists, call HP support. (Start de printer opnieuw op. Als het probleem hierdoor niet is opgelost, neemt u contact op met HP Support.
Een melding over printkopcontrole Dit is geen foutmelding. De melding verschijnt wanneer de optie Printhead monitoring (Printkopcontrole) is ingesteld op Intensive (Intensief). Als u de instelling op Optimized (Optimaal) zet, verschijnt de melding niet. Zie Printkopcontrole beheren.
u gevraagd om uw keuze te bevestigen. Als u uw keuze bevestigt, wordt de taak afgedrukt. In dat geval wordt de taak mogelijk afgedrukt op het verkeerde papiertype (waardoor de afdrukkwaliteit eventueel wordt beïnvloed) of op papier dat te smal is (waardoor de afdruk wordt afgesneden). Opmerking Als u de afdrukwachtrij wilt weergeven op het voorpaneel, klikt u achtereenvolgens op het pictogram en op Job queue (Afdrukwachtrij).
● Mogelijk is nesten ingeschakeld en wacht de printer tot de opgegeven time-out voor nesten is verstreken om de overeenkomstige nesten te berekenen. In dat geval wordt de resterende tijd vóór het verstrijken van de time-out voor nesten weergegeven op het printerscherm. ● Mogelijk hebt u een afdrukvoorbeeld gevraagd in het printerstuurprogramma. Dit is een functie waarmee u kunt controleren of de afbeelding de gewenste afbeelding is.
Een communicatiestoring tussen de computer en printer Dit kan onder andere de volgende symptomen hebben: ● De melding Receiving (Bezig met ontvangen) verschijnt niet op het voorpaneel wanneer u een afbeelding naar de printer hebt verzonden. ● Op de computer verschijnt een foutmelding wanneer u probeert af te drukken. ● De computer of printer loopt vast (blijft inactief) terwijl communicatie plaatsvindt.
ondersteuning voor IP via FireWire (zie Toegang krijgen tot de geïntegreerde webserver). Controleer of uw besturingssysteem is geconfigureerd om IP via FireWire te gebruiken. ● Controleer op het voorpaneel van de printer of IP is ingeschakeld voor het type verbinding dat u , kies I/O setup (I/O-configuratie), selecteer het type gebruikt. Selecteer het pictogram verbinding dat u gebruikt, selecteer vervolgens View information (Informatie weergeven) en controleer of u IP enabled (IP ingeschakeld) ziet.
De plaatrollen piepen Mogelijk moet u af en toe de rollen smeren. In de onderhoudsset bij de printer vindt u een fles geschikte olie. 1. Schakel de printer uit via de aan/uit-toets op het voorpaneel. 2. Open het venster. 3. Naast sommige rollen bevinden zich kleine openingen in de plaat. Plaats de punt van de fles olie uit de onderhoudsset in elke opening en spuit drie druppels olie in elke opening. 4. 322 Herhaal deze procedure voor alle openingen in de plaat. Hoofdstuk 23 Het probleem is...
NLWW 5. Zorg dat er geen olie op de plaat terechtkomt. 6. Als dat toch gebeurt, veegt u de olie weg met het doekje uit de onderhoudsset. 7. Laat het venster zakken.
324 Hoofdstuk 23 Het probleem is...
24 Vertel me over... (Onderwerpen over de geïntegreerde webserver) De geïntegreerde webserver is het regelcentrum voor beheer op afstand van de printer. Vanaf een willekeurige computer kunt u een standaard webbrowser gebruiken om verbinding te maken met de geïntegreerde webserver van de printer (zie Toegang krijgen tot de geïntegreerde webserver).
326 ● verschillende printerinstellingen wijzigen op de pagina Device Setup (Apparaatconfiguratie) ● een wachtwoord instellen om internettoegang tot de printer te beperken: zie Wachtwoordbeveiliging instellen voor de geïntegreerde webserver. Hoofdstuk 24 Vertel me over...
25 Vertel me over...
Kleuremulatiemodi De printer kan het kleurgedrag van andere apparaten emuleren: RGB-apparaten zoals monitors, en CMYK-apparaten zoals persen en printers. Zie De kleuremulatiemodus selecteren. Als het niet lukt om de printer een andere HP Designjet-printer te laten emuleren, gaat u naar Kleurovereenstemming tussen verschillende HP Designjets. Voor een goede emulatie heeft de printer een specificatie nodig van de kleuren die deze apparaten kunnen reproduceren.
● JMPA: Japanse standaard voor offsetpersen ● Photoshop 4 standaard CMYK ● Photoshop 5 standaard CMYK ● De printer kan andere HP Designjet-printers emuleren. Via het voorpaneel en de geïntegreerde webserver zijn enkele extra opties beschikbaar: ● Japan Color 2001 Coated gebruikt de Japan Color 2001-specificatie voor papier van type 3 (met coating).
● Apple RGB: emuleert de eigenschappen van een standaard Apple-monitor en wordt gebruikt door een hele reeks van DTP-toepassingen. Gebruik deze ruimte voor bestanden die u wilt weergeven op Apple-monitors of wanneer u wilt werken met oude DTP-bestanden. ● Adobe RGB (1998): biedt een redelijk breed bereik van RGB-kleuren. Gebruik deze ruimte als u productiewerk wilt afdrukken met een breed kleurbereik.
Opmerking Normaal gesproken branden de drie lampjes nooit tegelijk, omdat de printer niet kan afdrukken in de slaapstand. De interne afdrukken van de printer De interne afdrukken bieden verschillende soorten informatie over de printer. U kunt deze afdrukken opvragen via het voorpaneel van de printer. Hiervoor hoeft u geen computer te gebruiken. Voordat u een interne afdruk opvraagt, controleert u of er papier is geladen (rol of vel) en of de melding Ready (Gereed) op het voorpaneel staat.
● Image diagnostics (Afbeeldingsdiagnostiek): helpt u bij het oplossen van problemen met de afdrukkwaliteit. Zie Hoe... (Onderwerpen over Image Diagnostics Print (Beelddiagnoseafdruk)). ● Service information (Service-informatie): biedt informatie die onderhoudstechnici nodig hebben. Preventief onderhoud Tijdens de levensduur van de printer kunnen onderdelen die continu worden gebruikt, versleten raken.
26 Vertel me over...
Inktpatronen De vier inktpatronen van de printer voorzien de printkoppen van gele, magenta, zwarte en cyaan inkt. De kleurpatronen die bij de printer worden geleverd, hebben een capaciteit van 225 cm³. De zwarte patroon heeft een capaciteit van 400 cm³. U kunt ook kleurpatronen met een capaciteit van 400 cm³ en zwarte patronen met een capaciteit van 775 cm³ gebruiken. Opmerking De patronen van 225 cm³ en 400 cm³ hebben dezelfde buitenafmetingen, alleen de interne capaciteit varieert.
U wordt aangeraden de lege patroon te vervangen door een nieuwe patroon van HP: zie Een inktpatroon verwijderen en Een inktpatroon plaatsen. Het is weliswaar mogelijk om opnieuw gevulde inktpatronen of patronen van een andere leverancier dan HP te gebruiken, maar beide opties bieden verschillende ernstige nadelen: ● De printer kan beschadigd raken. In dat geval geldt de printergarantie niet voor de reparatie van schade die is veroorzaakt door de inktpatroon of voor problemen vanwege inktvervuiling.
De printkoppen zijn uiterst duurzaam en hoeven niet te worden vervangen elke keer dat u een inktpatroon vervangt. Ze blijven uitstekende resultaten bieden, zelfs wanneer de inktpatronen bijna leeg zijn. Voor het behoud van optimale afdrukkwaliteit worden de printkoppen automatisch met regelmatige intervallen getest. Indien nodig wordt automatisch onderhoud uitgevoerd. Dit duurt even en kan het afdrukken tijdelijk vertragen.
Tips voor het inktsysteem Volg altijd deze richtlijnen voor de beste resultaten: NLWW ● Op de verpakking staat de datum 'ten laatste installeren op'. Installeer de inktpatronen, printkoppen en printkopreinigers vóór deze datum. ● Vervang altijd de overeenkomstige printkopreiniger wanneer u een printkop vervangt. ● Volg de instructies op het voorpaneel tijdens de installatie. ● Laat de printer en de printkopreinigers de printkoppen automatisch reinigen.
338 Hoofdstuk 26 Vertel me over...
27 Vertel me over...
Papier gebruiken De keuze van het juiste papier voor uw toepassingen is van essentieel belang voor een goede afdrukkwaliteit. Voor de beste afdrukresultaten mag u alleen aanbevolen papiertypen gebruiken (zie Ondersteunde papiertypen selecteren), waarvan de betrouwbaarheid en eigenschappen specifiek voor uw printer zijn ontwikkeld en grondig zijn getest. Alle afdrukonderdelen (printer, inktsysteem en papier) zijn ontworpen om samen te werken voor probleemloos afdrukken en een optimale afdrukkwaliteit.
Opmerking Deze lijst wordt wellicht aangepast. Ga naar http://www.hp.com/go/designjet/ supplies/ voor de meest recente informatie.
Tabel 27-2 Overige ondersteunde papiertypen (vervolg) Productnaam Voorpaneelnaam HP Matte Backlit Film voor Spiegelprints Matte Film HP Studio Canvas [4000] Canvas HP Outdoor Billboard Papier met Blauwe Rug [downloaden] HP Matte Canvas [4000] Canvas HP Outdoor Papier [downloaden] HP Canvas Papier 140 g/m2 [4000] Canvas HP Canvas Papier 180 g/m2 [4000] Canvas HP Fine Art Aquarelpapier [4000] Super Heavy Coated Paper HP Fine Art Papier, crème [downloaden] HP Fine Art Papier, Sahara [downl
Sommige afdrukmaterialen zijn niet compatibel met de stapelaar, zoals: ● Heldere film en matte film ● Glanzend papier (behalve sneldrogend glanzend papier, dat wel mag worden gebruikt) Wanneer u afdrukt in de modus Fast (Snel) op de papiersoorten Translucent Bond, Vellum of Natural Tracing Paper, kunnen er enkele inktvlekken verschijnen in gebieden met veel inkt. Selecteer de modus Normal (Normaal) of Best om dit probleem te voorkomen. Zie Een andere afdrukkwaliteit instellen.
344 Hoofdstuk 27 Vertel me over...
28 Vertel me over... (onderwerpen over afdrukken met meer rollen) [4500] Opmerking NLWW Dit hoofdstuk is alleen van toepassing op de HP Designjet 4500-printerserie.
De toepassingen van een printer met meer rollen Een printer met meer rollen kan om verschillende redenen handig zijn. ● U kunt snel en zonder de printer aan te raken schakelen tussen verschillende papiertypen. ● U kunt snel en zonder de printer aan te raken schakelen tussen verschillende papierbreedten. Zo kunt u papier besparen door kleinere afbeeldingen op smaller papier af te drukken.
Tip U kunt in sommige gevallen ook papier besparen door uw afbeeldingen te draaien of te nesten. Zie Een afbeelding roteren en Taken nesten om rolpapier te besparen.
● Controleer het resterende inktniveau in de inktpatronen. ● De standaardbak wordt alleen aanbevolen voor minder dan 30 afzonderlijke afdrukken. De stapelaar kan tot 200 afdrukken bevatten. ● Wanneer u uw afdruktaken hebt verzonden, kunt u met de geïntegreerde webserver de status ervan controleren vanaf een externe locatie. ● De valdetectie moet zijn ingesteld op Intensive (Intensief). ● De droogtijd moet zijn ingesteld op Optimized (Optimaal).
29 Vertel me over...
Functionele specificaties Tabel 29-1 HP-inktpatronen nr. 90 Printkoppen Geel, magenta, zwart en cyaan (twee van elke kleur) Printkopreinigers Geel, magenta, zwart en cyaan (twee van elke kleur) Inktpatronen Gele, magenta en cyaan patronen met een inktinhoud van 225 cm³ of 400 cm³, en een zwarte cartridge met een inktinhoud van 400 cm³ of 775 cm³ Tabel 29-2 Papierformaten Minimaal Maximaal Breedte (Designjet 4000-serie) 11 in (279 mm) 42 in (1.
Tabel 29-3 Afdrukresolutie (vervolg) Print quality (Afdrukk waliteit) Maximu m Detail Optimized for drawings/text Renderingresolu tie (dpi) Afdrukresolutie (dpi) Optimized for images Renderingresolu tie (dpi) 1200×600 (andere papiertypen) Afdrukresolutie (dpi) 600×600 (Max Speed, Bright White, Bond Paper) 1200×600 (andere papiertypen) Off (Uit) 300×300 1200×1200 (Hoogglanzend Fotopapier) 300×300 1200×1200 (Hoogglanzend Fotopapier) 600×600 (Max Speed) 600×600 (Max Speed, Bright White, Bond Pape
Fysieke specificaties Tabel 29-7 Fysieke specificaties van de printer Gewicht (inclusief voet) ˜ 115 kg (Designjet 4000-serie) ˜ 185 kg (Designjet 4500-serie) Breedte < 1.930 mm Diepte < 800 mm Hoogte ˜ 1350 mm Tabel 29-8 Fysieke specificaties van de stapelaar Gewicht 53 kg Breedte 1286 mm Diepte 1.002–1.
Ecologische specificaties Voor de meest recente milieuspecificaties voor de printer gaat u naar http://www.hp.com/ en zoekt u op 'ecological specifications'.
354 Hoofdstuk 29 Vertel me over...
30 Vertel me over...
Inktpatronen bestellen U kunt de volgende inktbenodigdheden bestellen voor uw printer.
● :L geeft papiertypen aan die verkrijgbaar zijn in Latijns-Amerika ● :N geeft papiertypen aan die verkrijgbaar zijn in Noord-Amerika Het papier is in alle regio's verkrijgbaar wanneer het onderdeelnummer niet wordt gevolgd door een dubbele punt.
Tabel 30-5 Universal-serie Naam g/m² 24 in (107 cm) breed 36 in (107 cm) breed 42 inch (107 cm) breed 23,39 inch (59,4 cm) breed (A1) 33,11 inch (84,1 cm) breed (A0) HP Universal Hoogglanzend Fotopapier 190 Q1426A:AE N Q1427A:AE N Q1428A:AE N geen geen HP Universal Matglanzend Fotopapier 190 Q1420A:AE N Q1421A:AE N Q1422A:AE N geen geen HP Universal Sneldrogend Glanzend Fotopapier 190 Q6574A:AE N Q6575A:AE N Q6576A:AE N geen geen HP Universal Sneldrogend Matglanzend Fotopapier 1
Tabel 30-7 Grafische toepassingen/Indoor/Fine Art Naam g/m² 24 in (107 cm) breed 36 in (107 cm) breed 42 inch (107 cm) breed HP Matte Canvas 340 C7966A:AEN C7967A:AEN C7968A:AEN 140 geen Q1718A:EN geen 180 geen Q1724A:AEN geen 240 geen Q1703A geen HP Fine Art Papier, crème 140 geen Q1709A geen HP Fine Art Papier, Sahara 140 geen Q1715A:EN geen (Alleen voor de Designjet 4000-serie) HP Canvas Papier 140 g/m2 (Alleen voor de Designjet 4000-serie) HP Canvas Papier 180 g/m2 (Allee
360 Hoofdstuk 30 Vertel me over...
31 Vertel me over...
HP Instant Support HP Instant Support is de suite hulpprogramma's voor probleemoplossing van HP. Deze hulpprogramma's halen diagnostische informatie op bij de printer en vergelijken deze met intelligente oplossingen uit de Knowledge Bases van HP, zodat u problemen zo spoedig mogelijk kunt oplossen. U kunt een HP Instant Support-sessie starten door op de overeenkomstige koppeling te klikken in de geïntegreerde webserver van de printer. Zie Toegang krijgen tot de geïntegreerde webserver.
● Als het probleem hierdoor niet is opgelost, raadpleegt u het HP Support Services-boekje bij de printer. Dit document bevat een uitgebreide lijst van verschillende ondersteuningsservices die beschikbaar zijn om u te helpen bij het oplossen van printerproblemen.
U bepaalt welke informatie u nodig hebt: stem uw registratie af op de producten die u hebt aangeschaft en op uw type bedrijfsactiviteiten, en stel uw communicatievoorkeuren in. Registreer u bij HP Designjet Online voor de beste prestaties. HP Designjet Online is beschikbaar in het Engels, Duits, Frans, Italiaans, Spaans, Portugees, Japans, Koreaans, Vereenvoudigd Chinees en Traditioneel Chinees.
32 Wettelijke informatie NLWW ● Wereldwijde garantie: HP Designjet 4000/4500-printerserie en 4500mfp ● Softwarelicentieovereenkomst van Hewlett-Packard ● Verklaringen over open bron ● Internationale kennisgevingen ● VERKLARING VAN CONFORMITEIT 365
Wereldwijde garantie: HP Designjet 4000/4500-printerserie en 4500mfp HP-product Garantieperiode Printer 1 jaar (vanaf de datum waarop u het product hebt aangeschaft) Software 90 dagen (vanaf de datum waarop u het product hebt aangeschaft) Printkop Tot de datum 'end of warranty' (Einde van garantie) op het product is bereikt, of tot 1000 cm³ HP-inkt door de printkop is gestroomd (afhankelijk van wat het eerst wordt bereikt).
AANSPRAKELIJK VOOR SCHADE AAN OF VERLIES VAN BESTANDEN DIE U OP DE VASTE SCHIJF VAN DE PRINTER OF ANDERE OPSLAGAPPARATEN HEBT OPGESLAGEN. HP IS NIET AANSPRAKELIJK VOOR HET HERSTELLEN VAN VERLOREN BESTANDEN OF GEGEVENS. 6. Bij HP-printerproducten heeft het gebruik van een opnieuw gevuld of niet-origineel HPverbruiksartikel (inkt, printkop of inktpatroon) geen invloed op de HP-garantie die HP u biedt of op een HP-ondersteuningscontract dat u met HP hebt afgesloten.
11. Mogelijk zijn contracten voor extra services verkrijgbaar voor geautoriseerde HP-servicecentra wanneer het weergegeven HP-product wordt gedistribueerd door HP of een geautoriseerde importeur. 12.
Softwarelicentieovereenkomst van Hewlett-Packard LET OP: GEBRUIK VAN DE SOFTWARE IS ONDERHEVIG AAN DE SOFTWARELICENTIEVOORWAARDEN VAN HP DIE HIERNA WORDEN BESCHREVEN. DOOR DE SOFTWARE TE GEBRUIKEN GEEFT U AAN AKKOORD TE GAAN MET DEZE LICENTIEVOORWAARDEN. ALS U DEZE LICENTIEVOORWAARDEN NIET ACCEPTEERT, MOET U DE SOFTWARE RETOURNEREN. IN DAT GEVAL WORDT DE PRIJS VOLLEDIG GERESTITUEERD. ALS DE SOFTWARE BIJ EEN ANDER PRODUCT WAS GELEVERD, MAG U HET COMPLETE PRODUCT ONGEBRUIKT RETOURNEREN.
software is geïntegreerd in de HP Designjet 4000/4500-printer of 4500mfp, moet u stoppen met het gebruik van de HP Designjet 4000/4500-printer of 4500mfp. Exportvereisten. Het is u niet toegestaan de software of kopieën of aanpassingen daarvan te exporteren of opnieuw te exporteren als dit een inbreuk is op geldende wetten of voorschriften. Beperkte rechten van de Amerikaanse overheid. De software en eventuele bijbehorende documentatie zijn volledig met privé-middelen ontwikkeld.
Internationale kennisgevingen U kunt een kopie aanvragen van de meest recente documenten met gegevens over materiaalveiligheid van de inktsystemen die in de printer worden gebruikt. Hiervoor stuurt u een brief naar het volgende adres: Hewlett-Packard Customer Information Center, 19310 Pruneridge Avenue, Dept. MSDS, Cupertino, CA 95014, Verenigde Staten. Daarnaast is er een webpagina beschikbaar: http://www.hp.com/hpinfo/community/environment/ productinfo/psis_inkjet.
interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case users will be required to correct the interference at their own expense. Normes de sécurité (Canada) Le présent appareil numérique n'émet pas de bruits radioélectriques dépassant les limites applicables aux appareils numériques de Classe A prescrites dans le réglement sur le brouillage radioélectrique édicté par le Ministére des Communications du Canada.
Chinese EMI statement Sound Geräuschemission (Germany) LpA < 70 dB, am Arbeitsplatz, im Normalbetrieb, nach DIN45635 T. 19.
VERKLARING VAN CONFORMITEIT zoals is beschreven in ISO/IEC 22 en EN 45014 Naam van leverancier: Hewlett-Packard Company Naam van leverancier: Avenida Graells, 501 08174 Sant Cugat del Vallès Barcelona, Spanje verklaart dat het product Voorgeschreven modelnummer (3): BCLAA-0401, BCLAA-0503, BCLAA-0504 Productfamilie: HP Designjet 4000-printerserie, HP Designjet 4500-printerserie, HP Designjet 4500-scannerserie, HP Designjet 4500-stapelaarserie Productopties: Alle voldoet aan de volgende productspec
Josep-Maria Pujol Hardware Quality Manager Sant Cugat del Vallès (Barcelona) 28 juli 2005 Lokale contactpersonen, alleen voor regelgevingsonderwerpen Europa: Hewlett-Packard GmbH, HQ-TRE, Herrenberger Strasse 140, 71034 Böblingen, Duitsland. Verenigde Staten: Hewlett-Packard Company, Corporate Product Regulations Manager, 3000 Hanover Street, Palo Alto, USA-CA 94304, Verenigde Staten.
376 Hoofdstuk 32 Wettelijke informatie NLWW
Index A aanbevolen papiertypen 340 aangepast papierformaat 156 aansluiten, printer direct (Mac OS 9) [4000] 106 direct (Mac OS X) 105 direct (Windows) 100 hardware [4000] 43 hardware [4500] 73 Mac OS 9-netwerk [4000] 103 Mac OS X-netwerk 101 methode kiezen 98 Windows-netwerk 98 accessoires bestellen 359 accessoires [4000] installeren 44 achterkant, lampjes 330 afdrukken, gescand document [4500] 247 afdrukken met meer rollen [4500] 345 afdrukkwaliteit andere instellen 158 selecteren 158 afdrukresolutie 350
getrapte lijnen 289 Gigabit-Ethernet-accessoire [4000] installeren 44 grafische talen 351 H handmatige snijfunctie [4500] 136 hoogte-instelling 115 HP Customer Care 362 HP Designjet Online 363 HP-GL/2 167 HP Instant Support 362 I in-/uitschakelen, printer 110 InDesign 179 in elkaar zetten, printer [4000] 11 in elkaar zetten, printer [4500] 49 inktpatroon bestellen 356 informatie over 334 informatie weergeven 212 kan niet plaatsen 304 kan niet verwijderen 304 niet geaccepteerd 304 niet-HP 334 onderhoud 224 o
naam op voorpaneel 340 ondersteund 340 PDF 167 peninstellingen geen effect 300 Photoshop HP-GL/2 & RTLstuurprogramma 172 PostScript-stuurprogramma 176 piepende rollen 322 plaatsen, rol in printer [4000] 120 plaatsen, rol in printer [4500] 130 plaatsen, rol op as [4000] 118 plaatsen, rol op as [4500] 128 plaatsen, vel [4000] 125 PostScript 167 preventief onderhoud 332 printer, basisfuncties 2 printer, basisonderdelen [4000] 3 printer, basisonderdelen [4500] 4 printer aansluiten overzicht 330 printer configur
onderhoudswaarschuwingen 311 onleesbare cd/dvd 312 printer laadt de verkeerde rol 312 printer toevoegen 252 reinigen, de glasplaat 256 scannen naar bestand 246 scanvoorbeelden weergeven 249 sorteren, kopieën 256 strepen in afbeelding 312 timers instellen 257 toegang tot de gedeelde map 253 verkeerde taal 311 wachtlampje knippert 310 wordt niet gestart 311 schalen, afbeelding 165 scheefgetrokken lijnen 291 slaapstand, wachttijd 114 smeren, plaatrollen 322 smering printkopwagen 223 snel afdrukken 160 snijfunc