HP BladeSystem c7000 Enclosure Setup and Installation Guide Abstract This guide describes identification, operations, setup, configuration and utilities, troubleshooting, regulatory notices, specifications, and technical support. This guide is for an experienced service technician. HP assumes you are qualified in the servicing of computer equipment, trained in recognizing hazards in products, and are familiar with weight and stability precautions.
© Copyright 2006, 2013 Hewlett-Packard Development Company, L.P. The information contained herein is subject to change without notice. The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty. HP shall not be liable for technical or editorial errors or omissions contained herein.
Contents Planning the installation ................................................................................................................. 6 Verifying the pallet contents ........................................................................................................................ 6 Rack requirements ..................................................................................................................................... 7 Rack-free environment requirements ...................
Powering up the enclosure ........................................................................................................................ 59 Single-phase AC configuration ........................................................................................................ 59 Three-phase AC configuration ......................................................................................................... 64 HP BladeSystem Insight Display ......................................................
Preventing electrostatic discharge .............................................................................................................. 97 Grounding methods to prevent electrostatic discharge .................................................................................. 97 Acronyms and abbreviations ........................................................................................................ 98 Documentation feedback .................................................................
Planning the installation Verifying the pallet contents Item Name Description 1 HP BladeSystem c7000 Enclosure The HP BladeSystem enclosure 2 Rear cage The rear section of the enclosure 3 Device bay blank A mandatory insert installed in any unused device bay 4 Power supply blank A mandatory insert installed in any unused power supply bay 5 The power supply for the enclosure 6 Enclosure hot-plug power supply (quantity as ordered) Full-height device (quantity as ordered) The full-height se
Item Name Description 11 Onboard Administrator module Hot-pluggable enclosure management module. One module is required to manage the components installed in the enclosure. To provide redundant enclosure management, you can install an optional second module.
o Open area—Minimum of 65 percent open area to provide adequate airflow through any rack front or rear doors o Adjustable rack rails are shipped with each enclosure: — Minimum rail length: 63.5 cm (25 in) — Maximum rail length: 86.4 cm (34 in) Rack-free environment requirements The HP BladeSystem c7000 Enclosure (referred to as the enclosure) can be used in a rack-free environment.
WARNING: The enclosure is very heavy. To reduce the risk of personal injury or damage to the equipment: • Observe local occupational health and safety requirements and guidelines for manual material handling. • Remove all installed enclosure components from their enclosures before installing or moving the enclosures. • Use caution and get help to lift and stabilize enclosures during installation or removal, especially when the enclosure is not fastened to the rack.
CAUTION: When performing non-hot-plug operations, you must power down the server blade and/or the system. Use caution when performing other operations, such as hot-plug installations or troubleshooting. CAUTION: Protect the equipment from AC power fluctuations and temporary interruptions with a regulating facility UPS device. This device protects the hardware from damage caused by power surges and voltage spikes and keeps the system in operation during a power failure.
Temperature requirements To ensure continued safe and reliable equipment operation, install or position the rack in a well ventilated, climate-controlled environment. The operating temperature inside the rack is always higher than the room temperature and is dependent on the configuration of equipment in the rack. Check the TMRA for each piece of equipment before installation.
Component and LED identification Enclosure front components Item Description 1 Device bays* 2 Air intake slot (Do not block.) 3 Power supply bay 1 4 Power supply bay 2 5 Power supply bay 3 6 Power supply bay 4 7 Insight Display 8 Power supply bay 5 9 Power supply bay 6 10 Air intake slot (Do not block.) *For more information, see "Device bay numbering (on page 14).
Power supply bay numbering Power supply LEDs Power LED 1 (green) Fault LED 2 (amber) Condition Off Off No AC power to the power supply On Off Normal Off On Power supply failure For power supply configuration information, see Installing a power supply (on page 29).
Device bay numbering Each enclosure requires interconnects to provide network access for data transfer. Interconnects reside in bays located on the rear of the enclosure. Be sure to review device bay numbering to determine which external network connections on the interconnects are active. IMPORTANT: When looking at the rear of the enclosure, front device bay numbering is reversed.
HP BladeSystem Insight Display components Item Description Function 1 Insight Display screen Displays Main Menu error messages and instructions 2 Left arrow button Moves the menu or navigation bar selection left one position 3 Right arrow button Moves the menu or navigation bar selection right one position 4 OK button Accepts the highlighted selection and navigates to the selected menu 5 Down arrow button Moves the menu selection down one position 6 Up arrow button Moves the menu select
The following figure shows the location of the contacts on the c7000 enclosure that enable use of LDS.
Item Description 10 Onboard Administrator bay 2 11 Power supply exhaust vent (do not block) 12 Fan bay 10 13 Fan bay 9 14 Fan bay 8 15 Fan bay 7 16 Fan bay 6 17 AC power connectors 18 Onboard Administrator bay 1 19 Interconnect bay 7 20 Interconnect bay 5 21 Interconnect bay 3 22 Interconnect bay 1 Fan bay numbering Component and LED identification 17
Fan LED LED color Fan status Solid green The fan is working. Solid amber The fan has failed. Flashing amber See the Insight Display screen.
HP c7000 Onboard Administrator with KVM components Item Name Description 1 Reset button — 2 OA/iLO management port Ethernet 100BaseT RJ45 connector, which provides Ethernet access to the Onboard Administrator and the iLO on each blade. Also supports interconnect modules with management processors configured to use the enclosure management network. Also supports GbE.
Item Name Description 7 Serial connector Serial RS232 DB-9 connector with PC standard pinout. Connect a computer with a null-modem serial cable to the Onboard Administrator command line interface (CLI). 8 VGA VGA DB-15 connector with PC standard pinout. To access the KVM menu or Onboard Administrator CLI, connect a VGA monitor or rack KVM monitor for enclosure KVM.
Installation Installation overview To set up and install the enclosure: 1. Disassemble the enclosure ("Disassembling the enclosure" on page 21). 2. For rack-free installations ("Rack-free installation" on page 24), set up the enclosure on an appropriate surface, then install the rear cage and enclosure components. 3. For rack installations, install the enclosure into the rack ("Installing the enclosure into the rack" on page 26) then reassemble the enclosure. 4.
1. With the enclosure still on the pallet, remove all components from the front and rear of the enclosure. 2. Remove the rear cage: a. Loosen the thumbscrews and open the hinges completely.
b. Use the handles to extend the rear cage until the release levers engage on both sides of the rear cage. c. Grasp the handholds below the release levers. d. Disengage the release levers on both sides of the rear cage. CAUTION: When removing and lifting the rear cage, always grasp the handholds as far forward as possible. The front end of the rear cage is heavy and the handholds provide a more balanced location to distribute the weight of the cage during lifting.
e. Use the handholds to extend and remove the rear cage from the enclosure. Rack-free installation WARNING: To reduce the risk of personal injury or damage to the equipment in a rack-free environment: • Never stack the enclosure on top of another enclosure. • Never place equipment on top of the enclosure. • Never place the enclosure on a surface that cannot support up to 217.7 kg (480 lb). To set up the enclosure in a rack-free environment: 1. Select the location for the enclosure.
2. Use the rack template ("Measuring with the rack template" on page 25) to mark the locations for the rack rails. 3. Install the rack rails ("Installing the rack rails" on page 25) for each enclosure. 4. Install the enclosure into the rack ("Installing the enclosure into the rack" on page 26). Measuring with the rack template The rack template ships with the rack rail kit and provides detailed instructions on where to position the enclosure rack rails and where to install the four cage or clip nuts.
3. Slide the front end of the rail to the rack front column. When fully seated, the rack rail will lock into place. 4. Repeat the procedure for the right rack rail. Installing the enclosure into the rack The empty enclosure with the rear cage installed weighs 58.6 kg (129 lb). When the enclosure is disassembled, the empty enclosure without the rear cage installed weighs 35.5 kg (78 lb). The empty rear cage weighs 23.2 kg (51 lb).
2. Push the handles down on each side of the enclosure, and slide the enclosure fully into the rack. 3. Tighten the thumbscrews to secure the enclosure to the rack. 4. Install the rear cage into the enclosure. ("Installing the rear cage into the enclosure" on page 28) 5. Repeat the procedure for the remaining enclosures. NOTE: Up to four 10U enclosures can be installed in a 42U rack.
Installing the rear cage into the enclosure 1. Open all hinges completely. 2. Position the rear cage at the rear of the enclosure, and align the rear cage guiding fins with the guiding groove in the rack rails. 3. Slide the rear cage fully into the enclosure. CAUTION: Do not touch or bump rear cage connector pins when installing the rear cage into the enclosure.
4. Close the hinges, and tighten the thumbscrews to secure the rear cage. Component installation The following sections contain installation instructions for the individual enclosure components. All components must be installed and cabled before you power up the enclosure. There is no specific installation order requirement for the enclosure components.
NOTE: This document discusses installation of AC power supplies only. For information on configuring DC power supplies or HP Carrier Grade Solutions, see the documentation that came with your power supply. To install a power supply: 1. Slide the HP BladeSystem Insight Display to the right or left to gain access to all power supply bays. 2. Open the power supply bracket. 3. Insert the power supply into the enclosure, and then close the bracket.
Installing blades The c7000 enclosure is divided into four quadrants by the vertical support metal work. Within each quadrant, a removable divider supports half-height blades. To install a full-height blade in any quadrant, this divider must be removed. Therefore, a quadrant can only contain either full-height blades or half-height blades. CAUTION: Failure to install the divider in a quadrant when installing half-height blades can result in damage to the connectors on the server blades.
1. Remove the blank. 2. Remove the three adjacent blanks. 3. Remove the device bay shelf ("Removing a device bay shelf" on page 34). 4. Remove the connector covers.
5. Prepare the blade for installation. 6. Install the blade. CAUTION: To prevent improper cooling and thermal damage, do not operate the blade or the enclosure unless all drive and device bays are populated with either a component or a blank. 7. Install blanks in any empty bays.
Removing a device bay shelf 1. Remove the blank. 2. Slide the device bay shelf locking tab to the left to open it.
3. Push the device bay shelf back until it stops, lift the right side slightly to disengage the two tabs from the divider wall, and then rotate the right edge downward (clockwise). 4. Lift the left side of the device bay shelf to disengage the three tabs from the divider wall, and then remove it from the enclosure. Creating a full-height device bay blank 1.
2. Fit the coupler plate into the slots on top of the blank, and then slide the coupler plate back until it snaps into place. 3. Fit the slots on the bottom of the second blank on to the tabs on the coupler plate, and then slide the second blank forward until it snaps in place. 4. Install the full-height blank into the device bay.
Installing a half-height blade 1. Remove the blank. 2. Install the device bay shelf, if applicable. 3. Install the blade in the empty bay. Installing a device bay shelf You must install the device bay shelf to support half-height devices.
1. Remove the full-height blade, storage blade, or device bay blank. 2. To unlock device bay shelf locking tab, slide it to the left.
3. Tilt the shelf at an angle with the left edge up. Align the three tabs on the left edge of the shelf with the openings in the enclosure, and then push the device bay shelf up. CAUTION: Be sure that all five tabs (three on the left side of the shelf and two on the right side of the shelf) are fully engaged before sliding the shelf forward to complete the installation. Failure to do so can cause damage to server blade connectors during installation. 4.
5. To lock device bay shelf locking tab, slide it to the right. Connecting locally to a server blade with video and USB devices Use the local I/O cable to connect a monitor and any of the following USB devices: • USB hub • USB keyboard • USB mouse • USB CD/DVD-ROM drive • USB diskette drive Numerous configurations are possible. This section offers two possible configurations. Accessing a server blade with local KVM For this configuration, a USB hub is not necessary.
4. Connect a USB keyboard to the second USB connector. Item Description 1 Monitor 2 USB mouse 3 HP c-Class Blade SUV cable 4 Server blade 5 Video connector 6 USB keyboard Accessing local media devices Use a USB hub when connecting a USB diskette drive and/or USB CD-ROM drive to the blade. The USB hub provides additional connections. Use the following configuration when configuring a blade or loading software updates and patches from a USB CD/DVD-ROM or a USB diskette drive. 1.
o USB diskette drive Item Description 1 Monitor 2 USB mouse 3 HP c-Class Blade SUV cable 4 Server blade 5 USB hub 6 USB keyboard 7 USB CD/DVD-ROM drive or diskette drive Installing fans The HP BladeSystem c7000 Enclosure ships with four HP Active Cool 200 Fans and supports up to 10 fans. Install fans in even-numbered groups, based on the total number of blades installed in the enclosure.
1. Turn the handle counterclockwise to the unlock position, and pull the fan or fan blank from the enclosure. 2. Slide the fan into the enclosure until it locks in place. NOTE: When installing a fan in the top row of fan bays, orient the fan so that the LED is in the lower right corner. When installing a fan in the bottom row of fan bays, orient the fan so the LED is in the upper left corner.
To remove a fan, turn the handle counterclockwise to the unlock position, and pull the fan out of the enclosure. Installing Onboard Administrator modules The HP BladeSystem c7000 Enclosure is shipped with one HP BladeSystem Onboard Administrator with KVM module installed and can support up to two Onboard Administrator modules.
b. Pull the handle, and slide the Onboard Administrator blank out of the Onboard Administrator tray. 2. Slide the Onboard Administrator module into the Onboard Administrator tray, and close the handle. When the Onboard Administrator module is fully inserted, it locks into place. Attaching components to the HP c7000 Onboard Administrator with KVM For local access to the enclosure: 1. Connect a monitor (1) to the VGA connector (6) on the HP Onboard Administrator with KVM. 2.
3. Connect a USB mouse (2) and keyboard (3) to the USB hub (4). To connect the HP Onboard Administrator with KVM to an HP Server Console Switch or an HP IP Console Switch: 1. Connect the KVM interface adapter (2) to the VGA connector (4) and the USB connector (3) on the HP Onboard Administrator with KVM. 2. Connect a CAT5 cable (1) to the KVM interface adapter (2) and an optional HP Console Switch (5). Installing interconnect modules There are eight single-wide interconnect bays in the enclosure.
IMPORTANT: If the mezzanine card is not installed properly or the interconnect module installation does not coincide with the mezzanine card installation, the ports on the interconnect module will not function. NOTE: For more information on how and where to install mezzanine cards, see the server-specific user guide. To install an interconnect module: 1. Remove the interconnect blank, if applicable. 2.
Mapping to interconnect ports Several port types are referenced in the following tables. • Examples of 1x ports are 1-Gb Ethernet (1 GbE) switch modules and Fibre Channel interconnect modules. • An example of a 2x port is a Serial Attached SCSI (SAS) interconnect module. (Reserved for future use.) • Examples of 4x ports are 10-Gb Ethernet (10 GbE) interconnect modules. • Gen8 servers have FlexibleLOM adapters that have the same port mapping as the previous generation server blade Embedded NICs.
Mapping half-height blades The following table lists the available configurations for half-height devices installed in device bay N (1–16).
Connection Port number Connects to interconnect bay/port Comments Mezzanine slot 2—1x or 2x cards 1x/2x port 1x/2x port 1x/2x port 1x/2x port 4x port 1 4x port 2 5 / port N 6 / port N 7 / port N 8 / port N 5/Port N 7/Port N One or two single-wide interconnect modules Mezzanine slot 2—4x cards 1 2 3 4 One or two double-wide interconnect modules * Connectivity to interconnect bays 7 and 8 is only available with four-port mezzanine cards or port 2 of 4x card in Mezzanine slot 2.
Connection Port number Connects to interconnect bay/port Comments NIC NIC 1 NIC 2 NIC 3 NIC 4 1x/2x port 1x/2x port 1x/2x port 1x/2x port 4x port 1 1/Port 2/Port 1/Port 2/Port 3/Port 4/Port 3/Port 4/Port 3/Port One or two single-wide Ethernet interconnect modules Mezzanine slot 1—1x or 2x cards Mezzanine slot 1—4x cards 1 2 3 4 N+8 N+8 N N N N N+8 N+8 N One or two single-wide interconnect modules • • Mezzanine slot 2—1x or 2x cards Mezzanine slot 2—4x cards Mezzanine slot 3—1x or 2x cards Me
Interconnect device mapping for double dense server blades The following table lists the available configurations for double dense server blades installed in device bay N (1-16).
• B side To support network connections for specific signals, install an interconnect module in the bay corresponding to the embedded NIC or mezzanine signals. Interconnect bay identification Bay-to-bay crosslinks Four trace SerDes signals between adjacent bays are provided in the enclosure midplane to permit bay-to-bay communications. Interconnect modules can only connect horizontally.
Device bay crosslinks Device bay crosslinks are wired between adjacent horizontal device bay pairs. For half-height blades, these signals connect a four-lane PCIe module to a partner blade such as a tape blade or a PCI expansion blade. For full-height blades, these signals are used to connect a PCIe module to a partner blade in the lower adjacent bay and require a PCIe pass-thru mezzanine card installed in mezzanine connector 3.
Removing interconnect bay dividers The enclosure ships with interconnect bay dividers installed. The interconnect bay dividers must be removed before installing double-wide interconnect modules. To remove an interconnect bay divider, press the release tab, and pull the interconnect bay divider out of the enclosure. Installing interconnect bay dividers The enclosure ships with interconnect bay dividers installed. The interconnect bay dividers must be installed to use single-wide interconnect modules.
Cabling and powering up the enclosure Cabling the enclosure After all system hardware is installed, cable the components. See the HP ProLiant BladeSystem c-Class Site Planning Guide on the Documentation CD or the HP website (http://www.hp.com) for additional cabling and site planning requirements.
Item Connector Description 1 OA/iLO Ethernet 1000BaseT RJ45 connector, which provides Ethernet access to the Onboard Administrator and the iLO on each blade. Also supports interconnect modules with management processors configured to use the enclosure management network. Autonegotiates 1000/100/10 or can be configured to force 100Mb or 10Mb full duplex. 2 USB USB 2.
• Use the enclosure link-up port on the top enclosure for temporary connection to a PC using the enclosure service port ("Cabling a PC to the enclosure service port" on page 58) to provide quick access to any Onboard Administrator module, iLO, or interconnect module with Ethernet management ability. • Allow enclosure settings to be shared between enclosures, which simplifies deployment of multiple enclosures. NOTE: The enclosure link ports are designed only to support c-Class enclosures in the same rack.
2. Connect the laptop or PC 10/100Mb Ethernet port configured for DHCP addressing to the available link-up port on the top enclosure in the rack using a standard CAT5 patch cable. A Windows PC automatically obtains an IP address. If no IP address is obtained, configure the PC Ethernet port for static addressing using the IP address 169.254.1.254 with a netmask of 255.255.0.0. 3.
• Single-phase AC configuration using the HP Single-Phase Intelligent Power Module To cable the enclosure using a single-phase AC configuration: 1. Connect the AC power cables to the power connectors on the rear of the enclosure corresponding to the power supply that was populated on the front of the enclosure. 2. Be sure each power cable is securely attached to the power connectors. 3. Connect the AC power cables to the AC power source or to an installed power distribution unit (PDU). 4.
7. Place the power cord retention bracket under the power cords, and then align the power cords with the snap clamps. 8. Open the snap clamps, and then insert each power cord inside each clamp. 9. Slide the power cord retention bracket until the bracket touches the enclosure. 10. Insert the power cord retention tabs into the slots on the enclosure until they snap into place. 11. Slide each snap clamp over the end of each power cord overmold, and then squeeze each snap clamp closed.
minutes to power up, while an enclosure with fewer blades might take less time. Server blades are powered up incrementally, starting from device bay 1. When first initialized, the Onboard Administrator programs the mezzanine cards on the blades during discovery. After the mezzanine cards are programmed, powering up the enclosure takes only 1 to 2 minutes. The enclosure and the Insight Display now have power.
2. Connect the AC power cables to the installed PDU. 3. Power up the enclosure ("Powering up the enclosure" on page 59).
Three-phase AC configuration For a three-phase power configuration, the AC power cables are already attached to the enclosure. To cable the enclosure using a three-phase AC configuration: 1. Connect the AC power cables to the AC power source. 2. Turn on the AC circuit breakers that power the power cables installed in the enclosure. When the enclosure powers up for the first time, it might take up to 5 minutes before all blades are initialized and recognized by the Onboard Administrator.
HP BladeSystem Insight Display Insight Display overview The Insight Display enables the rack technician to configure the enclosure initially. It also provides information about the health and operation of the enclosure. See the HP BladeSystem Onboard Administrator User Guide for additional information. The Insight Display background color varies with the condition of the enclosure health: • Blue—The Insight Display background illuminates blue when the enclosure UID is active.
through the process of correcting the errors. The Installation Wizard automatically turns on the enclosure UID at the beginning of the installation and turns it off after the installation is complete. The Enclosure Settings screen is the first screen to appear. The background color is blue because the enclosure UID is active when this screen appears. 1. Review each setting on the Enclosure Settings screen for accuracy. 2.
o None Limit AC Input VA—The default setting is Not Set. You can change the Max AC Watts in increments of 50 Watts. Power Savings—The default setting is Enabled. The following selections are valid: o Enabled—You can place some of the power supplies on standby automatically to increase overall enclosure power subsystem efficiency. o Disabled—All power supplies share the load; the power subsystem efficiency varies based on load. OA1 IP Addr—The default setting is DHCP.
o Yes—Copy the configured power settings, rack name, and LCD Lockout PIN (if set) from the Enclosure Settings screen to the detected enclosures. o No—Continue configuring the current enclosure only. The Insight Display installation wizard must be run on each of the other detected enclosures. Select this option if each enclosure requires different power settings.
10. If no errors are detected, the rear enclosure UID turns off, and the Insight Display screen illuminates green. Press the OK button to return to the Main Menu. Enclosure and blade hardware setup and configuration is complete. If errors are detected, the Insight Display screen illuminates amber, and the Health Summary screen appears. For more information on troubleshooting configuration and installation errors, see Insight Display errors (on page 80).
The Main Menu appears: The Main Menu of the Insight Display has the following menu options: • Health Summary ("Health Summary screen" on page 70) • Enclosure Settings ("Running the Insight Display installation steps" on page 65) • Enclosure Info ("Enclosure Info screen" on page 73) • Blade or Port Info ("Blade and Port Info screen" on page 74) • Turn Enclosure UID on/off ("Turn Enclosure UID On/Off screen" on page 75) • View User Note ("View User Note screen" on page 77) • Chat Mode ("Chat Mo
When an error or alert condition is detected, the Health Summary screen displays the total number of error conditions and the error locations. Select Next Alert from the navigation bar, and press the OK button to view each individual error condition. The Insight Display displays each error condition in the order of severity. Critical alerts display first (if one exists), followed by caution alerts. When the enclosure is operating normally, the Health Summary screen displays green.
Select View Alert and press the OK button to display the errors. Select Details to view the details of the error. In the following example, the blade in bay 5 and the interconnect module in slot 3 have a configuration error.
Enclosure Settings screen The Enclosure Settings screen displays the following setting information about the enclosure, including: • Redundancy mode setting • Limit AC input VA setting • Power Savings mode setting • Active and Standby OA IP addresses • Enclosure Name • Rack Name • Insight Display PIN# TIP: Set a PIN to protect the enclosure settings from changes. Navigate the cursor to a setting or to the ?, and press OK to change the setting or get help on that setting.
• Rack name Blade and Port Info screen The Blade or Port Info screen displays information about a specific blade. On the first screen, select the blade number, then press the OK button. Select Blade Info or Port Info, and press the OK button. To view information about the blade, select Blade Info and press the OK button.
To view the ports used by a specific blade, select Port Info and press the OK button. On the following full-height blade, there are four embedded NICs. There are two interconnect modules located in interconnect bays 1 and 5, shown with bright green highlights. The other interconnect bays are empty. The four embedded NICs are connected to particular port numbers on the interconnect modules. The following Port Info screen shows a configuration error.
Selecting Turn Enclosure UID On from the main menu turns on the rear enclosure UID LED and changes the color of the Insight Display screen to blue. Selecting Turn Enclosure UID Off from the main menu turns off the rear enclosure UID LED and changes the color of the Insight Display screen to the current condition ("Insight Display overview" on page 65).
View User Note screen The View User Note screen displays six lines of text, each containing a maximum of 16 characters. Use this screen to display helpful information such as contact phone numbers or other important information. Change this screen using the remote Onboard Administrator user web interface. Both the background bitmap and the text can be changed.
Troubleshooting Troubleshooting resources The HP ProLiant Servers Troubleshooting Guide provides procedures for resolving common problems and comprehensive courses of action for fault isolation and identification, error message interpretation, issue resolution, and software maintenance on ProLiant servers and server blades. This guide includes problem-specific flowcharts to help you navigate complex troubleshooting processes. To view the guide, select a language: • English (http://www.hp.
This symbol indicates the presence of electric shock hazards. The area contains no user or field serviceable parts. Do not open for any reason. WARNING: To reduce the risk of injury from electric shock hazards, do not open this enclosure. This symbol on an RJ-45 receptacle indicates a network interface connection. WARNING: To reduce the risk of electric shock, fire, or damage to the equipment, do not plug telephone or telecommunications connectors into this receptacle.
WARNING: To reduce the risk of personal injury or damage to the equipment: 217.7 kg 480 lb • Observe local occupation health and safety requirements and guidelines for manual handling. • Obtain adequate assistance to lift and stabilize the chassis during installation or removal. • The server is unstable when not fastened to the rails. • When mounting the server in a rack, remove the power supplies and any other removable module to reduce the overall weight of the product.
Cooling errors Cooling errors occur when too few fans are installed in the enclosure or when the existing fans are not installed in an effective configuration. Cooling errors can occur on blades, storage blades, or interconnect modules. To correct a cooling error: 1. Use the arrow buttons to navigate to Fix This, and press OK. 2. Review and complete the corrective action suggested by the Insight Display.
• Fans • AC power inputs To correct a device failure error: 1. Use the arrow buttons to navigate to Fix This, and press OK. 2. Review and complete the corrective action suggested by the Insight Display. In most cases, you must remove the failed component to clear the error. 3. Replace the failed component with a spare, if applicable. NOTE: If the device failure error is an AC power input failure error, you must have the failed AC input repaired to clear the error.
Support and other resources Before you contact HP Be sure to have the following information available before you call HP: • Active Health System log (HP ProLiant Gen8 or later products) Download and have available an Active Health System log for 3 days before the failure was detected. For more information, see the HP iLO 4 User Guide or HP Intelligent Provisioning User Guide on the HP website (http://www.hp.com/go/ilo/docs).
providers or service partners) identifies that the repair can be accomplished by the use of a CSR part, HP will ship that part directly to you for replacement. There are two categories of CSR parts: • Mandatory—Parts for which customer self repair is mandatory. If you request HP to replace these parts, you will be charged for the travel and labor costs of this service. • Optional—Parts for which customer self repair is optional. These parts are also designed for customer self repair.
Pour plus d'informations sur le programme CSR de HP, contactez votre Mainteneur Agrée local. Pour plus d'informations sur ce programme en Amérique du Nord, consultez le site Web HP (http://www.hp.com/go/selfrepair). Riparazione da parte del cliente Per abbreviare i tempi di riparazione e garantire una maggiore flessibilità nella sostituzione di parti difettose, i prodotti HP sono realizzati con numerosi componenti che possono essere riparati direttamente dal cliente (CSR, Customer Self Repair).
HINWEIS: Einige Teile sind nicht für Customer Self Repair ausgelegt. Um den Garantieanspruch des Kunden zu erfüllen, muss das Teil von einem HP Servicepartner ersetzt werden. Im illustrierten Teilekatalog sind diese Teile mit „No“ bzw. „Nein“ gekennzeichnet. CSR-Teile werden abhängig von der Verfügbarkeit und vom Lieferziel am folgenden Geschäftstag geliefert. Für bestimmte Standorte ist eine Lieferung am selben Tag oder innerhalb von vier Stunden gegen einen Aufpreis verfügbar.
sustituciones que lleve a cabo el cliente, HP se hará cargo de todos los gastos de envío y devolución de componentes y escogerá la empresa de transporte que se utilice para dicho servicio. Para obtener más información acerca del programa de Reparaciones del propio cliente de HP, póngase en contacto con su proveedor de servicios local. Si está interesado en el programa para Norteamérica, visite la página web de HP siguiente (http://www.hp.com/go/selfrepair).
Opcional – Peças cujo reparo feito pelo cliente é opcional. Essas peças também são projetadas para o reparo feito pelo cliente. No entanto, se desejar que a HP as substitua, pode haver ou não a cobrança de taxa adicional, dependendo do tipo de serviço de garantia destinado ao produto. OBSERVAÇÃO: Algumas peças da HP não são projetadas para o reparo feito pelo cliente. A fim de cumprir a garantia do cliente, a HP exige que um técnico autorizado substitua a peça.
Support and other resources 89
Support and other resources 90
Regulatory compliance notices Regulatory compliance identification numbers For the purpose of regulatory compliance certifications and identification, this product has been assigned a unique regulatory model number. The regulatory model number can be found on the product nameplate label, along with all required approval markings and information. When requesting compliance information for this product, always refer to this regulatory model number.
radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver.
This Class A digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations. Cet appareil numérique de la classe A respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada. Class B equipment This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations. Cet appareil numérique de la classe B respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada.
Japanese notice BSMI notice Korean notice Class A equipment Class B equipment Regulatory compliance notices 94
Chinese notice Class A equipment Laser compliance This product may be provided with an optical storage device (that is, CD or DVD drive) and/or fiber optic transceiver. Each of these devices contains a laser that is classified as a Class 1 Laser Product in accordance with US FDA regulations and the IEC 60825-1. The product does not emit hazardous laser radiation. Each laser product complies with 21 CFR 1040.10 and 1040.11 except for deviations pursuant to Laser Notice No.
Taiwan battery recycling notice The Taiwan EPA requires dry battery manufacturing or importing firms in accordance with Article 15 of the Waste Disposal Act to indicate the recovery marks on the batteries used in sales, giveaway or promotion. Contact a qualified Taiwanese recycler for proper battery disposal.
Electrostatic discharge Preventing electrostatic discharge To prevent damaging the system, be aware of the precautions you need to follow when setting up the system or handling parts. A discharge of static electricity from a finger or other conductor may damage system boards or other static-sensitive devices. This type of damage may reduce the life expectancy of the device. To prevent electrostatic damage: • Avoid hand contact by transporting and storing products in static-safe containers.
Acronyms and abbreviations CSA Canadian Standards Association CSR Customer Self Repair ESD electrostatic discharge ICPM Insight Control Power Management IEC International Electrotechnical Commission iLO Integrated Lights-Out PDU power distribution unit RETMA Radio Electronics Television Manufacturers Association (rack spacing) SIM Systems Insight Manager TMRA recommended ambient operating temperature UID unit identification UPS uninterruptible power system Acronyms and abbreviations 98
USB universal serial bus Acronyms and abbreviations 99
Documentation feedback HP is committed to providing documentation that meets your needs. To help us improve the documentation, send any errors, suggestions, or comments to Documentation Feedback (mailto:docsfeedback@hp.com). Include the document title and part number, version number, or the URL when submitting your feedback.
Index A AC power configuration, single-phase 59 AC power configuration, three-phase 64 AC power configurations 59, 64 accessing a server blade with local KVM 40 accessing local media devices 41 airflow requirements 8, 10 alerts 65, 70, 80, 81 AMC Telco port mapping 52 authorized reseller 83 B batteries, replacing 95 battery replacement notice 95 bay numbering, full-height device 14 bay numbering, half-height device 14 bay numbering, interconnect 20, 53 bay numbering, power supply 13 bay to bay crosslinks 5
Ethernet switches 46 European Union regulatory notice 93 F fan bay numbering 17 fan configurations 42 fan errors 81 fan LED 18 fans, installing 42 FCC rating label 91 Federal Communications Commission (FCC) notice 91, 92 front components 12, 14 full-height device bay blank, creating 35 full-height device bay numbering 14 full-height server blades, mapping 50 G grounding methods 97 grounding requirements 11 H half-height device bay numbering 14 half-height server blades, mapping 49 Health Summary icon 69,
mapping to interconnect ports 48 measuring rack with template 25 mezzanine card 48 minimum requirements 11 modifications, FCC notice 92 N numbering, device bay 14 numbering, fan bays 17 numbering, full-height device bays 14 numbering, half-height device bays 14 numbering, interconnect bays 53 numbering, power supply bays 13 O Onboard Administrator components 18, 19 Onboard Administrator module 44 Onboard Administrator module, cabling 56 overview of installation process 21 P pallet contents 6 PDU (power d