user guide hp StorageWorks ESL9000 series tape library Sixth Edition (April 2003) Part Number: 243491-026 Product Regulatory Series ID Number: ED1002 This guide describes procedures for operating, maintaining, and troubleshooting the HP StorageWorks ESL9000 Series tape library.
© Hewlett-Packard Company, 2003. All rights reserved. Hewlett-Packard Company makes no warranty of any kind with regard to this material, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose. Hewlett-Packard shall not be liable for errors contained herein or for incidental or consequential damages in connection with the furnishing, performance, or use of this material. This document contains proprietary information, which is protected by copyright.
contents Contents About this Guide. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9 Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Document Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Text Symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Contents 2 Preparing the Library for Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39 Opening the Library Doors and Access Panels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 Connecting SCSI Cables. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 ESL9322 SCSI Cable Configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Contents Changing the Control Panel Security Levels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70 Securing the Control Panel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70 Changing Security Levels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71 4 Operator Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Contents B Regulatory Compliance Notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .109 Federal Communications Commission Notice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110 Class A Equipment. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110 Class B Equipment. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110 Modifications . . .
Contents 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 Library robotics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 Ultrium tape drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 HP Ultrium format trademark . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 SCSI ports (ESL9322) . .
Contents 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 8 Ultrium Tape Drive Capacity and Data Transfer Rate. . . . . . . . . . . . . . . . . . . . . . . . . . . 32 SDLT Tape Drive Capacity and Data Transfer Rate . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 SCSI Ports and Device Connections (ESL9322) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42 SCSI Ports and Device Connections (ESL9595) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
about this guide About this Guide This user guide provides information to help you: ■ Prepare the library for About operation. this Guide ■ Operate the control panel. ■ Use operator commands. ■ Maintain and troubleshoot the library.
About this Guide Conventions Conventions consist of the following: ■ Document Conventions ■ Text Symbols ■ Equipment Symbols Document Conventions The document conventions included in Table 1 apply in most cases.
About this Guide Caution: Text set off in this manner indicates that failure to follow directions could result in damage to equipment or data. Note: Text set off in this manner presents commentary, sidelights, or interesting points of information. Equipment Symbols The following equipment symbols may be found on hardware for which this guide pertains. They have the following meanings.
About this Guide Power supplies or systems marked with these symbols indicate the presence of multiple sources of power. WARNING: To reduce the risk of personal injury from electrical shock, remove all power cords to completely disconnect power from the power supplies and systems. Any product or assembly marked with these symbols indicates that the component exceeds the recommended weight for one individual to handle safely.
About this Guide Getting Help If you still have a question after reading this guide, contact an HP authorized service provider or access our website: http://www.hp.com. HP Technical Support In North America, call technical support at 1-800-652-6672, available 24 hours a day, 7 days a week. Note: For continuous quality improvement, calls may be recorded or monitored. Outside North America, call technical support at the nearest location.
About this Guide HP Authorized Reseller For the name of your nearest HP authorized reseller: 14 ■ In the United States, call 1-800-345-1518 ■ In Canada, call 1-800-263-5868 ■ Elsewhere, see the HP website for locations and telephone numbers: http://www.hp.com/support.
Library Description 1 This chapter describes the HP StorageWorks ESL9000 Series tape library and its components.
Library Description Library Models The HP StorageWorks ESL9000 Series tape library is an automated storage and retrieval library. It contains up to 8 drives and 322 cartridges for the ESL9322 Series, and up to 16 tape drives and 595 cartridges for the ESL9595 Series. The following ESL9000 Series tape library models support a wide range of storage and performance requirements.
Library Description The model number defines: ■ The standard inquiry string ■ The default number of bins The model number is set at the factory, and under normal circumstances, does not need to be changed.
Library Description Features and Benefits Your tape library provides the following features and benefits: ■ High-capacity, high-performance data storage and retrieval. ■ Expandable configurations: Up to five ESL9322 tape libraries and up to four ESL9595 tape libraries can be joined together into one multi-unit library system. Tape cartridges can be shared between libraries using optional Pass Through Mechanisms (PTMs). ■ Optional Fibre Channel upgrade kit.
Library Description Library Components The library consists of the following major components: ■ Cabinet ■ Control Panel ■ Robotics ■ Tape Drives ■ Load Port ■ Optional Pass-Through Mechanism (PTM) Cabinet The cabinet houses all library components including: ■ Robotics ■ Storage bins ■ Control electronics ■ Power supply and distribution equipment ■ Fans ■ Tape drives ■ Optional Fibre Channel upgrade kit Access these components through the front and back doors of the library cabine
Library Description ■ The power switch for the library is located behind a sliding panel on the front door below the control panel.
Library Description 5 4 1 3 2 5 Figure 2: Cabinet front panel (ESL9595) 1 Dual doors 3 Power switch 2 Load port with magazines 4 Touch screen control panel HP StorageWorks ESL9000 Series Tape Library User Guide 5 Viewing windows 21
Library Description Cabinet (Rear Panel) The rear of the cabinet (see Figure and Figure 4 on page 23) provides easy accessibility to: ■ Cooling fans ■ Power, control, and data interfaces ■ Tape drives 1 2 3 4 Figure 3: Cabinet rear panel (ESL9322) 22 1 Hot-pluggable removable fans 3 Hot-pluggable drives in removable canisters 2 Easy-access rear panel 4 Location of optional Fibre Channel upgrade kit HP StorageWorks ESL9000 Series Tape Library User Guide
Library Description 4 1 2 1 3 Figure 4: Cabinet rear panel (ESL9595) 1 Easy-access rear panel 3 Drive quick release thumbscrew on each bottom corner 2 Hot-pluggable drives in removable canisters 4 Hot-pluggable removable fans HP StorageWorks ESL9000 Series Tape Library User Guide 23
Library Description Storage Bins (ESL9322) The ESL9322 stores tape cartridges in the following locations: ■ Up to 171 storage bins on the back wall Note: Some bins are removed if a PTM is installed.
Library Description Figure 5: Storage bin numbering conventions (ESL9322) Note: Storage bin and drive numbering begins with 0. Consequently, the first drive is drive 0, the second drive is drive 1, etc.
Library Description Storage Bins (ESL9595) ■ The ESL9595 stores tape cartridges in the following locations: ■ 288 storage bins on the back wall ■ 196 storage bins on the inside of the left door ■ 111 storage bins on the inside of the right door ■ One load port consisting of two 4-cartridge stationary or 6-cartridge removable shelf bins ■ Up to 16 tape drives Figure 6 shows the storage bin, load port bin, and tape drive numbering conventions.
Library Description 399 400 401 402 403 404 405 406 407 408 409 410 411 412 413 414 435 436 437 438 439 440 441 442 443 444 445 446 447 448 449 450 475 476 477 478 479 480 481 482 483 484 485 486 487 488 489 490 515 516 517 518 519 520 521 522 523 524 525 526 527 528 529 530 415 416 417 418 451 452 453 454 455 456 457 458 491 492 493 494 495 496 497 498 531 532 533 534 535 536 537 538 419 420 421 422 423 424 425 426 427 428 429 430 431 432 433 434 459 460 461 462 463 464 465 466 467 468 469 470 47
Library Description Control Panel The control panel features a menu system for determining library status, configuring the library, and performing certain diagnostic functions (see Figure 7).
Library Description Robotics Figure 8 shows the library robotics, also referred to as the gripper or GRP on the library control panel. 1 2 3 4 Figure 8: Library robotics 1 Horizontal drive motor 3 Extension axis assembly 2 Mixed media gripper assembly 4 Vertical carriage assembly The vertical and horizontal actuators move the gripper into position to pick and place tape cartridges.
Library Description The gripper includes a Class II laser bar code scanner that reads up to 12-character, 3-of-9 format bar code labels. The scanner is used to maintain an inventory of the tape cartridges within the library. An inventory occurs automatically each time the library is turned on, or after the bulk load door has been closed. An inventory can also be initiated from the host computer.
Library Description Ultrium Tape Drives The Ultrium tape drive is a high-performance streaming tape drive that uses Linear Tape-Open (LTO) technology. An Ultrium 230 tape drive is capable of storing up to 100 GB (native) or 200 GB (2:1 compression) of data per cartridge. An Ultrium 460 tape drive is capable of storing up to 200 GB (native) or 400 GB (2:1 compression) of data per cartridge. Access the HP StorageWorks Ultrium Tape Drive User’s Guide from http://www.hp.
Library Description Table 5: Ultrium Tape Drive Capacity and Data Transfer Rate Drive Model Data Capacity Sustained Data Transfer Rate Ultrium 230 100 GB (native) 200 GB (compressed*) 15 MB/sec (54 GB/hour) 30 MB/sec (108 GB/hour) Ultrium 460 200 GB (native) 400 GB (compressed*) 30 MB/sec (108 GB/hour) 60 MB/sec (216 GB/hour) Note: *Compressed capacity assumes a 2:1 compression ratio.
Library Description For best results, always use HP branded media. The following tape cartridges are approved for the library’s Ultrium tape drives: ■ HP Ultrium Data Cartridge — C7972A (400 GB) — C7971A (200 GB) ■ HP Ultrium Universal Cleaning Cartridge — C7978A Note: Ultrium generation 2 cartridges (C7972A) can read and write to Ultrium generation 1 cartridges (C7971A). However, Ultrium generation 1 cartridges can only read and write to other Ultrium generation 1 cartridges.
Library Description SDLT Tape Drives The SDLT tape drive is a high-capacity, high-performance streaming tape drive that uses Laser Guided Magnetic Recording (LGMR) technology to maximize the amount of data that can be stored on a tape. An SDLT 320 tape drive is capable of storing up to 160 GB (native) or 320 GB (2:1 compression) of data per cartridge. Access the HP StorageWorks SDLT Tape Drive Reference Guide from http://www.hp.com/support for more information about its features and capabilities.
Library Description Table 6: SDLT Tape Drive Capacity and Data Transfer RateSHR 8000 Drive Model Data Capacity Sustained Data Transfer Rate SDLT 110/220 110 GB (native) 220 GB (compressed*) 11 MB/sec (39.6 GB/hour) 22 MB/sec (79.2 GB/hour) SDLT 160/320 160 GB (native) 320 GB (compressed*) 16 MB/sec (57.6 GB/hour) 32 MB/sec (11.5 GB/hour) Note: *Compressed capacity assumes a 2:1 compression ratio.
Library Description Caution: SDLT tape drives require special cleaning cartridges and data cartridges formatted specifically for SDLT. To avoid damage to your tape drive, it is critical to use appropriate cleaning cartridges, and properly formatted data cartridges. Do not use DLT Tape I, DLT Tape II, DLT Tape III, or DLT Tape IIIXT data cartridges, or DLT cleaning cartridges with SDLT tape drives.
Library Description Optional Network Storage Router HP StorageWorks Network Storage Routers provide bidirectional connectivity in a Fibre Channel Switched Fabric supporting Fibre Channel and SCSI devices. Internal and external models are available. For more information, visit http://www.hp.com/products/tapestorage, or contact your HP sales representative.
Library Description 38 HP StorageWorks ESL9000 Series Tape Library User Guide
Preparing the Library for Operation 2 This chapter explains how to prepare the HP StorageWorks ESL9000 Series tape library for operation. Sections in this chapter include: ■ Opening the Library Doors and Access Panels, page 40 ■ Connecting SCSI Cables, page 41 ■ Preparing Tape Cartridges, page 47 ■ Inserting and Removing Tape Cartridges, page 53 ■ Turning the Library On and Off, page 57 Note: If you have a slot capacity upgrade for your library, ensure that you order the license key immediately.
Preparing the Library for Operation Opening the Library Doors and Access Panels The ESL9322 has one front door and one rear access panel. The ESL9595 has two front doors and three rear access panels. To unlock and open front doors and rear access panels: 1. Using the key from the accessory kit, unlock the front door latch. 2. Lift the latch above the door lock. 3. Pull on the door latch to open the door, exposing the inside of the library cabinet. 4. Unlock any rear access panel using a 5/32 hex wrench.
Preparing the Library for Operation Connecting SCSI Cables This section describes the supported SCSI cable configurations for the tape libraries. ESL9322 SCSI Cable Configurations Figure 11 shows the SCSI ports as viewed from the rear of the ESL9322 tape library. L CONT. PTM DIAG.
Preparing the Library for Operation Drive # 0 SCSI ID 1 2 Drive # 1 SCSI ID 2 2 1 1 2 Drive # 2 SCSI ID 3 4 1 2 Drive # 3 SCSI ID 4 1 2 Drive # 4 SCSI ID 1 1 5 SCSI L SCSI K 2 Drive # 5 SCSI ID 2 1 Drive # 6 SCSI ID 3 2 Drive # 7 SCSI ID 4 2 SCSI I SCSI SCSI J A SCSI B SCSI C SCSI SCSI E D SCSI SCSI F G SCSI H 1 1 3 1 Terminators (8) 2 SCSI cables (8) 3 Drive Column 1 4 Robotic Controller 5 Host SCSI Cable Figure 12: Internal SCSI cabling configuration (ESL9322) Table 7:
Preparing the Library for Operation Table 7: SCSI Ports and Device Connections (ESL9322) (Continued) SCSI Port Identifier Device Connection J Not used K Robot L Host ESL9595 SCSI Cable Configurations Figure 13 shows the SCSI ports as viewed from the rear of the ESL9595 tape library. Q PTM DIAG. R CONT.
Preparing the Library for Operation Note: Drive numbering begins with 0. Consequently, the first drive is drive 0, the second drive is drive 1, etc.
Preparing the Library for Operation Table 8: SCSI Ports and Device Connections (ESL9595) (Continued) SCSI Port Identifier Device Connection F Drive 5 G Drive 6 H Drive 7 I Drive 8 J Drive 9 K Drive 10 L Drive 11 M Drive 12 N Drive 13 O Drive 14 P Drive 15 Q Host R Robot HP StorageWorks ESL9000 Series Tape Library User Guide 45
Preparing the Library for Operation Default SCSI IDs Table 9 lists the default SCSI IDs for the ESL9000 Series tape library. Note: The ESL9322 holds a maximum of 8 tape drives, with tape drive 7 being the highest-numbered tape drive. The ESL9595 holds a maximum of 16 tape drives, with tape drive 15 being the highest-numbered tape drive.
Preparing the Library for Operation Preparing Tape Cartridges Caution: Handle tape cartridges with care. Do not drop or mishandle them, or place them near sources of electromagnetic interference. Rough handling can damage the cartridge, making it unusable and potentially hazardous to the tape drives. Labeling Tape Cartridges Caution: The misuse and misunderstanding of bar code technology can result in backup and restore failures.
Preparing the Library for Operation SDLT Bar Code Labels SDLT cartridges have a front slide slot located on the face of the cartridge next to the write-protect switch (1 Figure 15). Use this slot for inserting the bar code label by sliding it into the slot. Caution: Do not apply labels onto the top, bottom, sides, or back of the cartridge as this may cause damage to the tape drive, or interfere with reliable operation.
Preparing the Library for Operation Ultrium Bar Code Labels Ultrium cartridges have a recessed area located on the face of the cartridge next to the write-protect switch. Use this area for attaching the adhesive-backed bar code label (see Figure 17). Do not apply labels onto the cartridge except in this designated area. Caution: The bar code label should be applied as shown in Figure 19 with the alphanumeric portion facing the hub side of the cartridge.
Preparing the Library for Operation For successful operation of your tape library, place the bar code label entirely within the recessed area, ensuring that no part of the label is outside of it (see Figure 17). Figure 17: Proper Ultrium bar code label placement Media Label Identifiers Be sure to use the proper bar code labels for your drive technology. Table 10 lists the identifier that is found at the end of 7- or 8-character SDLT and Ultrium bar code labels.
Preparing the Library for Operation Setting the Write-Protect Switch Each tape cartridge has a sliding write-protect switch. This switch determines whether new data can be written to the tape cartridge (write-enabled) or whether data on the tape cartridge is protected from being erased or overwritten (write-protected). Write-Protecting SDLT Tape Cartridges By moving the switch to the left (Figure 18), the tape cartridge is write-protected (orange indicator is visible).
Preparing the Library for Operation Write-Protecting Ultrium Tape Cartridges By moving the switch to the left(2 Figure 19), the tape cartridge is write-enabled. By moving the switch to the right(3 Figure 19), the tape cartridge is write-protected.
Preparing the Library for Operation Inserting and Removing Tape Cartridges You can insert tape cartridges by: ■ Placing them into fixed storage bins within the library cabinet ■ Using the load port on the library front panel Placing Tape Cartridges into Fixed Storage Bins 1. Label the tape cartridge (see Labeling Tape Cartridges on page 47). 2. Set the write-protect switch (see Setting the Write-Protect Switch on page 51). 3.
Preparing the Library for Operation Using the Load Port This section explains how to insert tape cartridges using the load port mechanism. Note: To move cartridges to the load port for removal, see “Moving Cartridges” in Chapter 4. To use the load port: 1. Prepare the tape cartridges to be inserted by affixing a bar code label, and write-protecting or write-enabling each tape cartridge as desired. 2. Press the Load Port button on the control panel. The library unlocks the load port. 3.
Preparing the Library for Operation 1 3 4 System Off-line Back Overvie Overvie ww 5 Forward Tapes Standby 2 Tape Port U Stop Home Drive D00 D03 Load Status ANF BLT 581 Ready120 Ready D01 Compre EMPTY Ready Write ssion D02 DLT ON ??? 7000 Protect Compa Ready OFF D03 SCSI cTape ANF ID: IV 05 Ready123 Operat or Service Activity Load Packs P00 ANF 146 GRP empty P01 ANF 147 P02 ANF 148 P03 ANF 149 System Off-line Back Bac Over Overvie Overvie view w Forwar Forward Tapes apes Standby Standb
Preparing the Library for Operation Using the Load Pack Magazine Use the load pack to add and remove tape cartridges. Adding a Cartridge to a Magazine The 4-cartridge magazines are stationary and built into the load port. Simply place cartridges into the bins with the bar codes facing out (see Figure 21): 1. Access the load pack magazines by opening the load port (see Using the Load Port on page 54). 2. Insert a tape cartridge into a load pack magazine. 3.
Preparing the Library for Operation Turning the Library On and Off Turning the Library On To turn the library on: 1. Verify that: a. All front doors and access panels are closed. b. All back panel cable connections are firmly in place. Note: If there are two AC power distribution assemblies, there will be two main circuit breakers. 2. Ensure that CB1 on the AC distribution assembly is turned on. It is located in the base of the cabinet behind the rear access panel.
Preparing the Library for Operation Turning the Library Off To turn the library off: 1. Place the library off-line by pressing the Standby button. The library robotics complete any current commands and then stop. 2. Verify that the control panel display shows System Off-line. 3. Verify that the gripper is empty by checking the Overview screen on the control panel (see Chapter 3). If there is a tape cartridge in the gripper, perform a Move command to place the cartridge in an available storage bin. 4.
Operating the Control Panel 3 This chapter provides an overview of the control panel and operating procedures.
Operating the Control Panel Using the Control Panel The control panel is activated by touching the screen, and is located at the front of the library. The menus displayed on the control panel let you obtain information about the library, execute library commands, and test library functions. The control panel functions are grouped into the following categories (see Figure 22): ■ Overview screen—Displays current tape drive, gripper, and load port content and activities.
Operating the Control Panel Table 11 lists the control panel menus and their functions.
Operating the Control Panel Table 12 describes the control panel navigation features. Table 12: Control Panel Navigation Component Horizontal bar Vertical bar Name Function Back button Moves you backwards screen by screen, through previous menu selections. Forward button Moves you forward screen by screen, through previous menu selections. Home button Redisplays you to the initial control panel screen. Contrast buttons Lets you adjust the contrast of the control panel screen.
Operating the Control Panel Table 12: Control Panel Navigation (Continued) Component Name Function Service screen Contains reporting functions, system tests, and service commands. To use this screen, you must have service-level access privileges. Multi-unit screen Lets you set the library unit, library unit number, number tape libraries, and Calibrate PTM. License screen Lets you enter a software key to access additional bins. Basic Operation Touching the screen activates the control panel.
Operating the Control Panel Exiting a Screen To exit any screen, press the Back or Home button. If a command is executing, the control panel displays a Command In Progress dialogue box with an Abort button. Pressing Abort cancels the command and stops the ongoing operation. After you press Abort, you must still press the Back button to exit the screen associated with the aborted command.
Operating the Control Panel 2 Lock icon Shows the current security level at the touch screen GUI. Five security levels are available: service (S), operator (O), user (U), import only (I), and locked (L). Table 13 on page 65 lists the attributes of each security level. 3 Load Port button Releases and locks the load port door. If the load port is locked in the closed position, pressing this button releases the load port and then locks the door.
Operating the Control Panel Obtaining Library Status The Overview and Tapes screens on the control panel provide library status. The Overview screen displays a snapshot of the tape drive, robot activity, and load port inventory (see Figure 24). The Tapes screen displays the inventory of all elements in the library (see Figure 25 on page 68). To display the Overview or Tapes screen, press the appropriate option on the control panel. Note that these functions operate in On-line or Off-line modes.
Operating the Control Panel Drive Status The Drives area reports whether or not: ■ A tape drive has a cartridge ■ The cartridge is write-enabled or write-protected ■ Compression is enabled It also provides status for: ■ Bar code labels ■ Drive states ■ Drive types ■ Media types ■ Drive serial numbers ■ Drive firmware level ■ Controller firmware level ■ SCSI IDs ■ Drive cleaning For a more detailed view of drive status, press on the desired drive to display the Tape Drive Status box
Operating the Control Panel Figure 25: Tape drive status box Activity Status The Activity area shows the source element, the transport medium, and the destination element involved in the activity. It also shows the current location of the tape cartridge and the progress of the activity. Load Port Status The Load Port area identifies tape cartridges currently stored in either magazine in the load port. Use the arrow button to view contents not currently displayed.
Operating the Control Panel Tapes Screen The Tapes screen identifies the tape cartridges residing in the following elements (see Figure 3-5): ■ Drives ■ Storage (fixed storage bins) ■ Load Port ■ Transport (gripper), and PTM Figure 26: Tapes screen Viewing Storage and Load Port Elements The Drives, Storage, and Load Port categories might contain too many elements to display at once. To scroll through these elements, use the arrow buttons at the bottom of each category.
Operating the Control Panel Changing the Control Panel Security Levels ESL 9000 Series library control panels have five levels of security: ■ Operator (O)—Provides access to the Operator set of screens and all functions on the system bar. ■ Service (S)—Provides access to both the Operator and Service set of screens and all functions on the system bar. ■ User (U)—Provides access to screens that are not password protected (Overview and Tapes screens) and all functions on the status bar.
Operating the Control Panel Changing Security Levels To change security levels: 1. Press the Lock icon. The Password screen is displayed (see Figure 27). Figure 27: Change password screen 2. Press the Security Level button for the desired level of security (Operator, Service, User, Import Only, or Locked). 3. Enter a password if necessary. A password is required to enter a higher security level than the current level. 4. Press the Enter button.
Operating the Control Panel Note: This procedure is especially useful to change from the Operator or Service levels to the User level after executing an Operator or Service level command. If the control panel is accessed from the Operator (O) or Service (S) level, and no activity has occurred for 15 minutes, it will return to the initial screen (Figure 22 on page 60), and to the default security level.
Operator Commands 4 This chapter describes the commands found on the Operator screen of the library control panel.
Operator Commands Opening the Operator Screen To open the Operator screen: 1. Press the Operator tab. The control panel displays the password screen (see Figure 28). Note: To change passwords, see “Changing Security Levels” on page 71.
Operator Commands 2. To gain access to the Operator screen, enter the correct operator or service password and press Enter (see Figure 29 on page 75). The default operator password is 1234.
Operator Commands Configuring the Library The Configure Library command lets you assign the following: ■ Library model number ■ Number of storage bins ■ Number of drives ■ Library SCSI ID ■ Tape drive SCSI ID ■ PTM configuration Note: The serial number and IEEE ID fields are set automatically through the library firmware. To configure any of these attributes: 1. In the Operator screen, press the Configure Library button. The control panel displays the Configure: Library screen (see Figure 30).
Operator Commands 2. Press the Configure button. The control panel displays the Configure: Library Settings screen (see Figure 31). Make sure that the library is off-line. Figure 31: Configure: library settings screen (ESL9595 shown) 3. Press the Select button until you highlight the setting you want to change. 4. Using the arrow buttons, scroll through the available values for the setting. 5. Press the Change button to accept the new value. 6. Repeat step 3 through step 5 to make other changes. 7.
Operator Commands Caution: The model number is set at the factory and should be changed only at the direction of an authorized service representative. SCSI ID Assignment Guidelines When selecting SCSI ID numbers, each SCSI device on the same bus must have a unique number from 0 to 15. SCSI devices include the library robotics, the host bus adapter, and the library tape drives.
Operator Commands Configuring Library Options The Configure Options command lets you set the following: ■ Power-On State—Determines whether the library is on-line or in standby mode when powered up (default is On-Line). ■ Auto Clean—Allows the library to perform drive cleaning tasks automatically as needed (default is Disable). Note: Cleaning should be done using your backup application software.
Operator Commands Note: Before changing the Auto Drive Unload configuration option, check the recommendations of your software application. ■ Auto Drive Unload—Causes the drive to unload a tape when a Move Medium command is received (default in Enable). ■ Barcode Retries—Lets you set a number of attempts to read a bar code label before giving up (default is 8). ■ Set StorageWorks Defaults—Returns all configure options to factory default states.
Operator Commands 2. Press the button for the desired option. 3. Using the arrow buttons, scroll through available values for the selected option. 4. When the New Value box displays the desired value, press the Execute button to apply the new value. The Current Value box displays the new value. 5. Repeat step 2 through step 4 to change other configuration options. 6. When you have finished making changes to library options, press the Back button until you return to the initial Operator screen.
Operator Commands Viewing the Error Log The library error log records library errors and the time they occurred (see Appendix C for a listing of the error codes and descriptions). Because the library has no system clock, the time stamps indicate uptime since the last power cycle. Note: At the time an error occurs, the control panel will indicate the error, along with a description of the error. After the error has been cleared, it can still be viewed from the error log. To view the error log: 1.
Operator Commands Calibrating the Library The Calibrate Library command lets you calibrate the storage bins, the tape drives, the load port, or the entire library. Calibrate the library during initial installation and after any maintenance procedure. To calibrate library elements: 1. From the Operator page, press the Calibrate Library button. The control panel displays the Calibrate Library screen (see Figure 33). 2. Press the button for the calibration option you want.
Operator Commands Performing an Inventory The Inventory Tapes command reads the bar code labels of the cartridges in the tape drives, fixed storage bins, and the load port bins. All elements that contain cartridges without labels are marked as full with no label. To perform an inventory: 1. Press the Inventory Tapes button in the Operator screen. The control panel displays a Command In Progress screen. 2. Press the Abort button to stop continuous running of the inventory process.
Operator Commands Moving Cartridges The Move Cartridge command lets you move any tape cartridge in the library to the destination you specify. This destination can be a storage bin, a tape drive, the load port, the gripper, or the PTM. Note: To move a cartridge from a tape drive when auto-drive unload is disabled, issue an Unload Drive command. (See “Unloading a Drive” on page 87.) To move a cartridge: 1. From the Operator screen, press the Move Cartridge button.
Operator Commands 2. Identify the source element of the cartridge: a. Press the appropriate source element button (Storage Bin, Drive, Load Port, Gripper, or PTM). When you press an element type, the Range box (below the Dest. box) displays the range of addresses. b. Using the keypad, enter the address of the source element and then press the Select button. The Source information is displayed in the Source box and the Dest. box becomes active. 3. Identify the destination for the cartridge: a.
Operator Commands Unloading a Drive The Unload Drive command prepares a tape cartridge to be removed from a drive by rewinding and ejecting the cartridge. After unloading the drive, remove the tape cartridge using the Move Cartridge command. To unload a drive: 1. From the Operator screen, press the Unload Drive button. The control panel displays the Control: Unload Drive screen (see Figure 35). Figure 35: Control: unload drive screen 2.
Operator Commands Unloading the Load Port The Unload Imp/Exp command moves a tape cartridge from the load port to an available storage bin. This option must be invoked after inserting a tape into the load port whenever the library Auto Load feature is disabled. See “Configuring Library Options”on page 79. Note: You can also use the Move Cartridge command to unload the load port. This command is especially useful if the destination of the move is important.
Maintenance and Troubleshooting 5 This chapter provides troubleshooting and maintenance information for the HP StorageWorks ESL9000 Series tape library.
Maintenance and Troubleshooting Troubleshooting Common Problems This section describes problems you might encounter during the setup and operation of the HP StorageWorks ESL9000 Series tape library. Corrective information is provided to help you resolve the problems. Several of these problems produce error messages on the control panel called sense data values. Sense data value messages consist of a number and a description of the error.
Maintenance and Troubleshooting Table 14: Start Up Problems (Continued) Problem Corrective Action During initialization, the library reports “Not Ready.” ■ One or more tape drives fail to spin up during start-up. ■ ■ ■ ■ The library starts up in standby mode. Determine the failure type by checking any previous error codes returned to the host computer. Correct the cause of the error. With the tape drive powered off, check all power connections.
Maintenance and Troubleshooting Robotics Problems Table 16 lists corrective actions for robotics problems. Table 16: Robotics Problems Problem The robot does not move at powerup. ■ Make sure that all internal packing materials (shipping brackets, foam pads, and tie wraps) have been removed. ■ Check the Stop and Standby buttons to ensure the library is on-line, and the Stop button is disabled. The gripper partially grips a tape cartridge.
Maintenance and Troubleshooting Table 16: Robotics Problems (Continued) Problem The robot drops a cartridge. Corrective Action ■ Open the front door. ■ Retrieve the cartridge, check it for damage, orient it properly, and place the cartridge in an empty storage bin. (Do not try to place the cartridge in the gripper.) Visually inspect the gripper and extension axis.
Maintenance and Troubleshooting Operating Problems Table 17 lists corrective actions for problems that might occur during library operation. If the problem persists, contact your authorized service provider. Table 17: Operating Problems Problem The host computer cannot communicate with the library, or one or more of the drives. Corrective Action ■ ■ ■ ■ ■ A tape cartridge is reported as not present.
Maintenance and Troubleshooting Table 17: Operating Problems (Continued) Problem A Move command failed. Corrective Action ■ Check the source and destination. The source should hold the cartridge to be moved, and the destination should be empty. ■ Make sure the gripper is empty and all actuators are free of obstruction. ■ Make sure the library is on-line and the Stop button is released. ■ Retry the command. A flash memory error is reported. Contact your HP service representative.
Maintenance and Troubleshooting Tape Drive Problems Table 18 lists corrective actions for tape drive problems. If the problem persists, contact your authorized service provider. Table 18: Tape Drive Problems Problem The library does not recognize the tape drive. The tape drive does not power up. Corrective Action ■ Make sure all SCSI cabling is properly connected. ■ Verify correct SCSI termination. ■ Make sure the SCSI ID is correct. ■ Make sure firmware is up to date.
Maintenance and Troubleshooting Tape Drive Interface LED Problems Table 19 lists the corrective actions for tape drive interface LED problems. If the problem persists, contact your authorized service provider. Table 19: Tape Drive Interface LED Problems Red Led Green Led Condition Action Required ON ON Reserved condition. Contact your authorized service provider. ON Flashing Reserved condition. Contact your authorized service provider. ON OFF Drive power fail.
Maintenance and Troubleshooting Maintaining Tape Cartridges Note: In addition to the information provided in this manual, access the HP StorageWorks SDLT Tape Drive Reference Guide, and the HP StorageWorks Ultrium Tape Drive User’s Guide from http://www.hp.com/support for more information. For longer life of recorded or unrecorded tape cartridges: 98 ■ Do not carry cartridges loosely in a container that exposes them to unnecessary physical shock.
Maintenance and Troubleshooting If a tape cartridge is dropped or damage is suspected, gently shake the tape cartridge: ■ If it rattles, it is damaged. Restore the data on the tape cartridge by some means other than by using the tape drive, and discard the damaged tape cartridge. ■ If it doesn't rattle, check the tape leader inside the cartridge. To do this, open the door on the rear of the tape cartridge by releasing the door lock.
Maintenance and Troubleshooting Cleaning Tape Drives Use the guidelines in the following sections to clean your tape drives. Cleaning SDLT Tape Drives Be aware of the following: ■ Under normal conditions, the cleaning cartridge is effective for about 20 cleanings. ■ SDLT tape drives typically do not need regular cleaning, as their design allows for minimal head contamination. ■ Use the cleaning tape only if the cleaning Alert light is on.
Maintenance and Troubleshooting Cleaning Ultrium Tape Drives Be aware of the following: ■ Ultrium tape drives have been developed to have a minimal cleaning requirement. Note: Only use HP-approved Ultrium cleaning cartridges. ■ An HP Ultrium Universal Cleaning Cartridge can be used up to 50 times. If you are using an older HP Ultrium cleaning cartridge, check the documentation that came with your media. Caution: Only use HP Ultrium Universal Cleaning Cartridges in the Ultrium 460 tape drive.
Maintenance and Troubleshooting Using HP StorageWorks Library and Tape Tools To provide continued service to our customers, HP provides the HP StorageWorks (L&TT) software application. L&TT is a diagnostic tool that is designed to aid in the installation and maintenance of both HP tape devices and tape libraries. L&TT includes several features designed to be used by both HP storage customers and trained service personnel.
Specifications A This appendix lists characteristics and specifications of the HP StorageWorks ESL9000 Series tape library. These characteristics and specifications are categorized as follows: ■ Physical Characteristics, page 104 ■ Performance Characteristics, page 106 ■ Environmental Specifications, page 106 ■ Safety and Regulatory Specifications, page 107 Note: For tape drive specifications, see the appropriate tape drive product manual.
Specifications Physical Characteristics Table 20 lists dimensions and other physical characteristics of the ESL9322 tape library. Table 20: Physical Characteristics (ESL9322) Description 104 Specifications ESL9322 Width 40 in (101.
Specifications Table 21 lists dimensions and other physical characteristics of the ESL9595 tape library.
Specifications Performance Characteristics Table 22 lists the performance characteristics of the library. Table 22: Performance Characteristics Description Specification Average swap time 22 seconds, consisting of two Move Medium commands Inventory (fully loaded with cartridges) Less than 5 minutes Environmental Specifications Table 23 lists the power-environmental and mechanical-environmental specifications of the library.
Specifications Table 23: Environmental Specifications (Continued) Description Altitude Specification Operating Shipping and storage Sea level to 10,000 ft (3,048 m) Sea level to 12,000 ft (3,657 m) Heat dissipation Operating 5500 BTU/hr (1400 KCal/hr or 1600 W) for ESL9595 4125 BTU/hr (1050 KCal/hr or 1200 W) for ESL9322 Acoustical noise (sound power level) Operating Idle 8.10 Bel 7.
Specifications 108 HP StorageWorks ESL9000 Series Tape Library User Guide
Regulatory Compliance Notices B This appendix includes the following information: ■ Federal Communications Commission Notice, page 110 ■ Canadian Notice (Avis Canadien), page 112 ■ European Union Notice, page 112 ■ BSMI Class A Notice, page 113 ■ Japanese Notice, page 113 ■ Laser Device, page 113 ■ Laser Regulation Labels, page 115 HP StorageWorks ESL9000 Series Tape Library User Guide 109
Regulatory Compliance Notices Federal Communications Commission Notice Part 15 of the Federal Communications Commission (FCC) Rules and Regulations has established Radio Frequency (RF) emission limits to provide an interference-free radio frequency spectrum. Many electronic devices, including computers, generate RF energy incidental to their intended function and are, therefore, covered by these rules.
Regulatory Compliance Notices equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: ■ Reorient or relocate the receiving antenna. ■ Increase the separation between the equipment and receiver. ■ Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Regulatory Compliance Notices Canadian Notice (Avis Canadien) Class A Equipment This Class A digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations. Cet appareil numérique de la classe A respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada. Class B Equipment This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations.
Regulatory Compliance Notices BSMI Class A Notice Japanese Notice Laser Device All HP systems equipped with a laser device comply with safety standards, including International Electrotechnical Commission (IEC) 825. With specific regard to the laser, the equipment complies with laser product performance standards set by government agencies as a Class 1 laser product. The product does not emit hazardous light; the beam is totally enclosed during all modes of customer operation and maintenance.
Regulatory Compliance Notices Laser Safety Warnings WARNING: To reduce the risk of exposure to hazardous radiation: Do not try to open the laser device enclosure. There are no user-serviceable components inside. Do not operate controls, make adjustments, or perform procedures to the laser device other than those specified herein. Allow only HP authorized service technicians to repair the laser device. Compliance with CDRH Regulations The Center for Devices and Radiological Health (CDRH) of the U.S.
Regulatory Compliance Notices Laser Regulation Labels Product Conformation Label The product conformation label is on the rear panel of the library (see Figure 36). Figure 36: Product conformation label Laser Caution Label The laser light caution label is near the laser (see Figure 37). CAUTION LASERLIGHT DO NOT STARE INTO BEAM 670NM LASERDIODE VORSICHT 1.0 MILLI WATT MAX CLASS II LASER PRODUCT LASERSTRAHLUNG, NICHT IN DEN LIGHTSTRAHL BLICKEN, SICHTBARE LASERSTRAHLUNG.
Regulatory Compliance Notices 116 HP StorageWorks ESL9000 Series Tape Library User Guide
Sense Data Values C This appendix lists sense data values and descriptions. These values appear in library error codes, as well as in the library error log.
Sense Data Values Sense Data Values Table 26 lists message information that can be sent from the library to a host computer ■ Sense key ■ ASC ■ Additional Sense Code Qualifier (ASCQ) ■ Message name, description, and (potential) recovery action ■ Valid interfaces — SCSI (host computer) — DIAG (diagnostic port/computer) — Both = SCSI and DIAG port The message name and description might contain abbreviations as follows: ■ (A/D) Analog-to-Digital ■ (DEV) Device ■ (DIAG) Diagnostics ■ (LU) Logi
Sense Data Values Table 26: Sense Data Values (Hexadecimal) (Continued) Sense Key ASC ASCQ 02 04 00 LU IS NOT READY, CAUSE NOT REPORTABLE Check library power. Retry command. 02 04 01 LOGICAL UNIT IN PROCESS OF BECOMING READY Wait for library to complete initialization. 02 04 02 LOGICAL UNIT INIT REQUIRED Element status or calibration unknown. Run an inventory command. 02 04 03 LU IS NOT READY, MANUAL INTERVENTION REQ’D Initialization failed.
Sense Data Values Table 26: Sense Data Values (Hexadecimal) (Continued) Sense Key ASC ASCQ 04 80 0F LOW POWER ERROR Check power connections, and check for failed power supplies. 04 80 11 MOTOR POWER FAILURE Indicates motor power turned off for a reason not otherwise reported. Toggle of the Stop button should clear. If the motor power failure occurs after the action of closing the door, or when the door is not latched, then upgrade firmware to latest revision. Check door switches.
Sense Data Values Table 26: Sense Data Values (Hexadecimal) (Continued) Sense Key ASC ASCQ 04 82 20 ROTARY TEST FAILURE Call your authorized service provider. 04 82 23 ROTARY POSITION OVERFLOW The position step counter overflowed. Issue a CALIBRATE ALL command. 04 83 00 EXTENSION INTERNAL FAILURE Upgrade firmware to latest revision. Extension axis code internal failure. Call your authorized service provider. 04 83 01 EXTENSION TIMEOUT Retry the command.
Sense Data Values Table 26: Sense Data Values (Hexadecimal) (Continued) Sense Key ASC ASCQ 04 83 22 EXTENSION ENCODER FAILURE The value of the extension encoder did not change during the self-test. Visually inspect extension axis and belt, look for debris, excessive wear of damage. 04 83 40 EXTENSION FORCE NOT REACHED During calibration or pushing in a drive, the extension never reached its intended force. If error is occurring during a place to a drive, ensure drive is securely installed.
Sense Data Values Table 26: Sense Data Values (Hexadecimal) (Continued) Sense Key ASC ASCQ 04 84 08 VERTICAL HOME NOT FOUND Vertical axis did not reach the home position. Visually inspect vertical axis and belt, look for debris, excessive wear, or damage. 04 84 20 VERTICAL TEST FAILURE The value of the vertical encoder did not change during the self-test. Visually inspect vertical axis and belt, look for debris, excessive wear, or damage.
Sense Data Values Table 26: Sense Data Values (Hexadecimal) (Continued) Sense Key ASC ASCQ 04 85 08 HORIZONTAL HOME NOT FOUND Horizontal axis did not reach the home position. Issue CALIBRATE ALL and retry operation. Check vertical sensors and flag. 04 85 20 HORIZONTAL TEST FAILURE The value of the horizontal encoder did not change during the self-test. Visually inspect vertical axis and belt, look for debris, excessive wear, or damage. Issue CALIBRATE ALL and retry operation.
Sense Data Values Table 26: Sense Data Values (Hexadecimal) (Continued) Sense Key ASC ASCQ 04 8B 03 PASSTHRU MECHANICAL POSITION ERROR Check for obstructions (cables, etc.). Disconnect unit from power then manually move the axis to ensure it moves freely between cabinets, with no binding or undue friction. Retry command. 04 8B 08 PASSTHRU HOME NOT FOUND Check for obstructions (cables, etc.).
Sense Data Values Table 26: Sense Data Values (Hexadecimal) (Continued) Sense Key ASC ASCQ 04 F3 02 DRIVE COMMUNICATION TIMEOUT The library is unable to communicate with a drive. Reseat drive module. 04 F3 11 DRIVE HANDLE NOT OK The tape drive is reporting that the handle cannot open. (This might indicate that a cartridge is present that has not been unloaded.) 05 1A 00 PARAMETER LIST LENGTH ERROR Make sure the software supports the library and has the latest patches and updates.
Sense Data Values Table 26: Sense Data Values (Hexadecimal) (Continued) Sense Key ASC ASCQ 05 30 03 Message Name/Description CLEANING CARTRIDGE INSTALLED One of the following conditions exist: ■ A cleaning cartridge cannot be removed from a drive because it is being used in a cleaning operation. ■ A cartridge cannot be placed into the drive because the drive is being cleaned.
Sense Data Values Table 26: Sense Data Values (Hexadecimal) (Continued) Sense Key ASC ASCQ 05 4E 00 OVERLAPPED COMMANDS ATTEMPTED Due to a second command being sent from the same host before a previous command has completed, the previous command has been aborted. This can also occur when executing off-line commands via the control panel and DIAG port simultaneously. Do not run backup software and diagnostic software at the same time.
Sense Data Values Table 26: Sense Data Values (Hexadecimal) (Continued) Sense Key ASC ASCQ 05 85 11 HORIZONTAL INVALID COMMAND Horizontal axis commanded to position out of library mechanical limits. Calibrate the library. Upgrade firmware to latest revision. If occurred when system was online, call your authorized service provider. 05 8A 02 UNCALIBRATED POSITION Library requires calibration. Run a CALIBRATE ALL command.
Sense Data Values Table 26: Sense Data Values (Hexadecimal) (Continued) Sense Key ASC ASCQ 06 28 01 IMPORT OR EXPORT ELEMENT ACCESSED Information message. Load port door has been closed. 06 29 00 POWER-ON, OR BUS DEVICE RESET OCCURRED Informational message. If power on occurs, the host user should assume the inventory might have been corrupted, and should run a CALIBRATE ALL command.
Sense Data Values Table 26: Sense Data Values (Hexadecimal) (Continued) Sense Key ASC ASCQ 06 80 0E DATA TRANSFER CHANGED A drive has been inserted into the library. 06 88 00 WARNING SAFE TEMPERATURE EXCEEDED This is only a warning that the temperature in the library exceeds the normal operational temperature 96.8oF (36oC). Check fans, look for airflow obstructions, and make sure ambient room temperature is sufficiently cool.
Sense Data Values Table 26: Sense Data Values (Hexadecimal) (Continued) Sense Key ASC ASCQ 0B 80 06 TRANSFER EMPTY - COMMAND ABORTED Gripper does not contain cartridge at end of pick portion of MOVE command. Check location of cartridge used in operation. Retry operation. 0B 80 0B COMMAND ABORTED BY USER Informational message. No action is necessary.
Sense Data Values Table 26: Sense Data Values (Hexadecimal) (Continued) Sense Key ASC ASCQ 0B 82 05 ROTARY BACK FAILURE The rotary move to the back position failed. Retry the command. If the failure recurs, issue a SELF-TEST command. Replace the robotics controller. 0B 83 01 EXTENSION TIMEOUT Extension axis did not reach desired position. Retry command. 0B 83 10 EXTENSION INVALID ACTUATOR START POSITION Extension axis position is unknown. Issue a CALIBRATE ALL command.
Sense Data Values Table 26: Sense Data Values (Hexadecimal) (Continued) Sense Key ASC ASCQ 0B 8B 10 PASSTHRU INVALID ACTUATOR START POSITION Pass-through axis position is unknown. Issue a CALIBRATE ALL command. Upgrade firmware to latest revision. Call your authorized service provider. 0B 8B 60 PTM FULL The PTM contains a cartridge. Issue a command to retrieve the cartridge from the PTM and place it in either a bin or a tape drive.
Capacity on Demand D The HP StorageWorks ESL9322 and ESL9595 tape libraries ship with the maximum number of physical storage slots available. However access to these slots requires an upgrade key for the library to recognize them. ESL9322: ■ 222 slots (standard) ■ Upgrade to 322 slots ESL9595: ■ 400 slots (standard) ■ Upgrade to 500 slots ■ Upgrade to 595 slots Note: To purchase a slot upgrade kit, contact your HP authorized reseller or sales representative.
Capacity on Demand Upgrading Your Capacity After you obtain your upgrade key, you can upgrade the capacity of your library: 1. Make sure all jobs running on the library have been stopped, and then place the library into Standby mode. 2. Ensure that you have the upgrade key. 3. Touch the License tab on the control panel. Figure 39: License screen (ESL9595 shown) 4. Enter the number of bins you are upgrading to and then press Select. 5. Enter the license number provided to you by HP. 6.
Capacity on Demand If you receive an error message: 1. Verify that the license number you entered is correct and enter it again. 2. Contact your HP sales representative. Note: Application software may need to be closed and restarted and the library reconfigured to work properly with the newly enabled bins.
Capacity on Demand 138 HP StorageWorks ESL9000 Series Tape Library User Guide
index A Set StorageWorks Default 81 Standby 57, 58, 62, 70, 91, 92, 119, 130 Stop 62, 64, 70, 92, 95, 119 Storage Bin 86 Tape Drive 86 Unload Drive 87 Unload Imp/Exp 88 User 71 additional sense code qualifier 118 ASC 118 ASCQ 118 authorized reseller, HP 14 B Index C Index bar code 30, 40, 47, 48, 49, 50, 52, 54, 56 buttons Abort 64, 84, 86, 87, 88 Back 62, 64, 69, 77, 81 Backspace 85 Calibrate All 83 Calibrate Library 83 Change 77 Configure 77 Configure Library 76 Configure Options 80 Contrast 62 Ex
Index common problems and solutions 90 configuration 76 library options 79 library settings 77 SCSI ID assignment 78 control panel 28, 60 features 62 functions 60, 61 initial screen 60 problems 91 securing 70 security levels 70 using 60 conventions document 10 equipment symbols 11 text symbols 10 D data values 118 document conventions 10 E environmental specifications 106 equipment symbols 11 European Union Notice 112 exposure caution label 115 F features and benefits 18 front panel 19 front view 20 G
Index tapes screen 69 load pack 56 installation and removal 56 load port 36, 55 button 55 location ESL9322 20 ESL9595 21 magazine 55 opening 54 operating 55 tape cartridge 55 unloading 88 M manageability 18 mixed media 30 model numbers 17 models 16 MOVE 58 moving cartridges 85, 88 multi-unit operation 28 O operating problems 94 operator screen 74 opening 74 optional PTM 36 P pass-through mechanism 18 performance characteristics 106 performing an inventory 84 physical characteristics 104 power switch loc
Index start-up problems 90 storage and load port elements 69 symbols in text 10 symbols on equipment 11 T tape cartridge locations ESL9322 24 ESL9595 26 tape cartridges inserting 72 installation and removal 56 installing 56 mixed media 30 moving 85 tape drive cleaning 36 tape drives 30, 32 LTO Ultrium 31 mixed media 30 SDLT 31 unloading 87 tapes screen 69 technical support, HP 13 text symbols 10 troubleshooting control panel problems 91 operating problems 94 142 robotics problems 92 sense data values 11