User Guide
© Copyright 2013 Hewlett-Packard Development Company, L.P. Bluetooth is a trademark owned by its proprietor and used by Hewlett-Packard Company under license. Intel and Centrino are trademarks of Intel Corporation in the U.S. and other countries. AMD is a trademark of Advanced Micro Devices, Inc. SD Logo is a trademark of its proprietor. Java is a U.S. trademark of Sun Microsystems, Inc. Microsoft and Windows are U.S. registered trademarks of Microsoft Corporation.
Safety warning notice WARNING! To reduce the possibility of heat-related injuries or of overheating the computer, do not place the computer directly on your lap or obstruct the computer air vents. Use the computer only on a hard, flat surface. Do not allow another hard surface, such as an adjoining optional printer, or a soft surface, such as pillows or rugs or clothing, to block airflow.
iv Safety warning notice
Table of contents 1 Welcome .......................................................................................................................................................... 1 Finding information ............................................................................................................................... 2 2 Getting to know your computer ..................................................................................................................... 4 Top .....................
4 Navigating using the keyboard, touch gestures and pointing devices ................................................... 23 Using pointing devices ....................................................................................................................... 23 Setting pointing device preferences ................................................................................... 23 Using the pointing stick ..............................................................................................
Initiating and exiting Sleep ................................................................................ 36 Initiating and exiting Hibernation ....................................................................... 36 Using the power meter and power settings ....................................................... 37 Setting password protection on wakeup ........................................................... 37 Using battery power ....................................................................
Using the docking connector (select models only) ............................................................ 50 8 Drives ............................................................................................................................................................. 51 Handling drives ................................................................................................................................... 51 Using hard drives ............................................................
10 Maintenance ................................................................................................................................................ 68 Adding or replacing memory modules ................................................................................................ 68 Cleaning your computer ..................................................................................................................... 70 Cleaning procedures ..................................................
13 Support ........................................................................................................................................................ 85 Contacting support ............................................................................................................................. 85 Labels ................................................................................................................................................. 86 14 Specifications .......................
1 Welcome After you set up and register the computer, it is important to take the following steps: ● Connect to the Internet—Set up your wired or wireless network so that you can connect to the Internet. For more information, see Connecting to a network on page 15. ● Update your antivirus software—Protect your computer from damage caused by viruses. The software is preinstalled on the computer. For more information, see Using antivirus software on page 65.
Finding information The computer comes with several resources to help you perform various tasks. Resources For information about Setup Instructions poster ● How to set up the computer ● Help to identify computer components Help and Support ● Operating system information To access Help and Support, select Start > Help and Support.
Resources For information about Limited Warranty* Warranty information To access this guide, select Start > Help and Support > User guides > View Warranty Information. – or – Go to http://www.hp.com/go/orderdocuments. *You can find the expressly provided HP Limited Warranty applicable to your product located with the user guides on your computer and/or on the CD/DVD provided in the box. In some countries/regions, HP may provide a printed HP Limited Warranty in the box.
2 Getting to know your computer Top TouchPad Component 4 Description (1) Pointing stick (select models only) Moves the pointer and selects or activates items on the screen. (2) Left pointing stick button Functions like the left button on an external mouse. (3) TouchPad on/off button Turns the TouchPad on and off. (4) TouchPad zone Moves the pointer and selects or activates items on the screen. (5) Left TouchPad button Functions like the left button on an external mouse.
Lights Component (1) Description Power light ● On: The computer is on. ● Blinking: The computer is in the Sleep state. ● Off: The computer is off. (2) Caps lock light On: Caps lock is on. (3) Microphone mute light ● Amber: Microphone sound is off. ● Off: Microphone sound is on. (4) Num lock light On: Num lock is on. (5) Wireless light ● White: An integrated wireless device, such as a wireless local area network (WLAN) device and/or a Bluetooth® device, is on.
Buttons and fingerprint reader (select models only) Component (1) Description Power button ● When the computer is off, press the button to turn on the computer. ● When the computer is on, press the button briefly to initiate Sleep. ● When the computer is in the Sleep state, press the button briefly to exit Sleep. ● When the computer is in Hibernation, press the button briefly to exit Hibernation. CAUTION: Pressing and holding down the power button will result in the loss of unsaved information.
Component Description (4) Volume mute button Mutes and restores speaker sound. (5) Fingerprint reader (select models only) Allows a fingerprint logon to Windows, instead of a password logon. Keys Component Description (1) esc key Displays system information when pressed in combination with the fn key. (2) fn key Executes frequently used system functions when pressed in combination with a function key, the num lk key, the esc key, or the b key.
Front Component (1) (2) (3) (4) 8 Description Wireless light Power light AC adapter/Battery light Hard drive light Chapter 2 Getting to know your computer ● White: An integrated wireless device, such as a wireless local area network (WLAN) device and/ or a Bluetooth® device, is on. ● Amber: All wireless devices are off. ● On: The computer is on. ● Blinking: The computer is in the Sleep state. ● Off: The computer is off.
Right Component Description (1) Memory card reader Reads data from and writes data to memory cards such as Secure Digital (SD). (2) Audio-out (headphone) jack/Audio-in (microphone) jack Produces sound when connected to optional powered stereo speakers, headphones, earbuds, a headset, or television audio. Also connects an optional headset microphone. WARNING! To reduce the risk of personal injury, adjust the volume before putting on headphones, earbuds, or a headset.
Left Component (1) Description Security cable slot Attaches an optional security cable to the computer. NOTE: The security cable is designed to act as a deterrent, but it may not prevent the computer from being mishandled or stolen. (2) USB 2.0 port Connects an optional USB device. NOTE: For details about different types of USB ports, see Using a USB device on page 48. (3) Vent Enables airflow to cool internal components.
Rear Component (1) Description USB 3.0 port Connects optional USB 3.0 devices and provide enhanced USB power performance. NOTE: For details about different types of USB ports, see Using a USB device on page 48. (2) Power connector Connects an AC adapter. (3) AC adapter/Battery light ● White: The computer is connected to external power and the battery is charged from 90 to 99 percent. ● Off: The battery is fully charged. (4) RJ-45 (network) jack Connects a network cable.
Display Component Description (1) WLAN antennas (2)* (select models only) Send and receive wireless signals to communicate with wireless local area networks (WLAN). (2) WWAN antennas (2)* (select models only) Send and receive wireless signals to communicate with wireless wide area networks (WWAN). (3) Internal microphones (2) Record sound. (4) Webcam light (select models only) On: The webcam is in use. (5) Webcam (select models only) Records video and captures photographs.
Bottom Component Description (1) Battery release latch Releases the battery. (2) Battery bay Holds the battery. (3) SIM slot Supports a wireless subscriber identity module (SIM) (select models only). The SIM slot is located inside the battery bay. (4) Docking connector Connects an optional docking device. (5) Accessory battery connector Connects an optional accessory battery. (6) Service cover release lock Locks the service cover.
Component (8) Description Vents (3) Enable airflow to cool internal components. NOTE: The computer fan starts up automatically to cool internal components and prevent overheating. It is normal for the internal fan to cycle on and off during routine operation. (9) Service cover Provides access to the hard drive bay, the wireless LAN (WLAN) module slot, the WWAN module slot, and the memory module slots.
3 Connecting to a network Your computer can travel with you wherever you go. But even at home, you can explore the globe and access information from millions of websites using your computer and a wired or wireless network connection. This chapter will help you get connected to that world. Connecting to a wireless network Wireless technology transfers data across radio waves instead of wires.
Using HP Connection Manager (select models only) HP Connection Manager provides a central location for managing your wireless devices, an interface for connecting to the Internet using HP Mobile Broadband, and an interface for sending and receiving SMS (text) messages.
NOTE: The terms wireless router and wireless access point are often used interchangeably. ● A large-scale WLAN, such as a corporate or public WLAN, typically uses wireless access points that can accommodate a large number of computers and accessories and can separate critical network functions.
Setting up a WLAN To set up a WLAN and connect to the Internet, you need the following equipment: ● A broadband modem (either DSL or cable) (1) and high-speed Internet service purchased from an Internet service provider ● A wireless router (2) (purchased separately) ● A wireless computer (3) NOTE: Some modems have a built-in wireless router. Check with your ISP to determine what type of modem you have.
Connecting to a WLAN To connect to the WLAN, follow these steps: 1. Turn on the computer. Be sure that the WLAN device is on. If the device is on, the wireless light is on. If the wireless light is off, press the wireless button. NOTE: On some models, the wireless light is amber when all wireless devices are off. 2. Click the network status icon in the notification area, at the far right of the taskbar. 3. Select a WLAN to connect to. 4. Click Connect.
in the HP Mobile Broadband information provided with your computer or the mobile network operator may provide it separately from the computer. For information about inserting and removing the SIM, see the Inserting and removing a SIM on page 20 section in this chapter. For information about HP Mobile Broadband and how to activate service with a preferred mobile network operator, see the HP Mobile Broadband information included with your computer. For additional information, see the HP website at http://www.
To remove a SIM, press in on the SIM, and then remove it from the slot. Using GPS (select models only) Your computer may be equipped with a Global Positioning System (GPS) device. GPS satellites deliver location, speed, and direction information to GPS-equipped systems. For more information, see the HP GPS and Location software Help.
To connect the network cable, follow these steps: 1. Plug the network cable into the network jack (1) on the computer. 2. Plug the other end of the network cable into a network wall jack (2) or router. NOTE: If the network cable contains noise suppression circuitry (3), which prevents interference from TV and radio reception, orient the circuitry end of the cable toward the computer.
4 Navigating using the keyboard, touch gestures and pointing devices Your computer allows navigation using touch gestures (select models only) in addition to the keyboard and mouse. Touch gestures can be used on your computer TouchPad. Select computer models have special action keys or hot key functions on the keyboard to perform routine tasks.
Turning the TouchPad off and on To turn the TouchPad off and on, quickly double-tap the TouchPad on/off button. Using TouchPad Gestures Your TouchPad allows you to navigate the pointing device on the screen by using your fingers to control the pointer action. The TouchPad supports a variety of gestures. To use TouchPad gestures, place two fingers on the TouchPad at the same time. NOTE: TouchPad gestures are not supported in all programs. To view the demonstration of a gesture: 1.
Tapping To make an on-screen selection, use the Tap function on the TouchPad. ● Tap one finger on the TouchPad zone to make a selection. Double-tap an item to open it. Scrolling Scrolling is useful for moving up, down, or sideways on a page or image. ● Place two fingers slightly apart on the TouchPad zone and then drag them up, down, left, or right.
Pinching/zooming Pinching and zooming allow you to zoom out or in on images or text. ● Zoom in by placing two fingers together on the TouchPad zone and then moving your fingers apart. ● Zoom out by placing two fingers apart on the TouchPad zone and then moving your fingers together. Rotating (select models only) Rotating allows you to turn items such as photos. ● 26 Anchor the forefinger of your left hand in the TouchPad zone.
2-Finger click (select models only) 2-Finger click allows you to make menu selections for an object on the screen. ● Place two fingers on the TouchPad zone and press to open the options menu for the selected object. Flicking (select models only) Flicking allows you to navigate through screens or quickly scroll through documents. ● Place three fingers on the TouchPad zone and flick your fingers in a light, quick motion up, down, left or right.
Using the keyboard The keyboard and mouse allow you to type select items, scroll and to perform the same functions as using touch gestures. The keyboard also allows you to use action keys and hot keys to perform specific functions. NOTE: Depending on the country or region, your keyboard may have different keys and keyboard functions than those discussed in this section. Identifying the hot keys A hot key is a combination of the fn key and either the esc key or one of the function keys.
Hot key combination Description fn+f7 Increases speaker volume. fn+f8 Mutes or restores microphone sound. fn+9 Decreases the screen brightness level. fn+f10 Increases the screen brightness level. fn+f11 Turns the keyboard backlight on and off. NOTE: The keyboard backlight is turned on at the factory. To extend battery life, turn off the keyboard backlight. Using keypads The computer includes an embedded numeric keypad or an integrated numeric keypad.
5 Multimedia Your computer may include the following: ● Integrated speaker(s) ● Integrated microphone(s) ● Integrated webcam (select models only) ● Preinstalled multimedia software ● Multimedia buttons or keys Using the media activity controls Depending on your computer model, you may have the following media activity controls that allow you to play, pause, fast forward, or rewind a media file: ● Media buttons ● Media hot keys (specific keys pressed in combination with the fn key) ● Media ke
NOTE: Refer to the Getting to know your computer on page 4 section for information on what type of volume controls your computer has. Connecting headphones You can connect wired headphones to the headphone jack on your computer. To connect wireless headphones to your computer, follow the device manufacturer's instructions. WARNING! To reduce the risk of personal injury, lower the volume setting before putting on headphones, earbuds, or a headset.
Video Your HP computer is a powerful video device that enables you to watch streaming video from your favorite websites and download video and movies to watch on your computer without needing to connect to a network. To enhance your viewing enjoyment, use one of the video ports on the computer to connect an external monitor, or projector.
NOTE: Thunderbolt is new technology. Install all the latest drivers for your Thunderbolt device before connecting the device to the Thunderbolt port. Thunderbolt cable and Thunderbolt device (sold separately) must be compatible with Windows. To determine whether your device is Thunderbolt Certified for Windows, see https://thunderbolttechnology.net/products. 1. Connect one end of the Thunderbolt cable to the Thunderbolt port on the computer. 2.
To connect a video or audio device to the DisplayPort: 1. Connect one end of the DisplayPort cable to the DisplayPort port on the computer. 2. Connect the other end of the cable to the video device, and then see the device manufacturer’s instructions for additional information. NOTE: To remove the device cable, press down on connector release button to disconnect it on the computer.
6 Power management NOTE: A computer may have a power button or a power switch. The term power button is used throughout this guide to mean both types of power controls. Shutting down the computer CAUTION: Unsaved information is lost when the computer shuts down. The shutdown command closes all open programs, including the operating system, and then turns off the display and computer.
NOTE: You cannot initiate any type of networking connection or perform any computer functions while the computer is in the Sleep state. Intel Rapid Start Technology (select models only) For select models, the Intel Rapid Start Technology (RST) feature is enabled by default. Rapid Start Technology allows your computer to resume quickly from inactivity. Rapid Start Technology manages your power-saving options as follows: ● Sleep—Rapid Start Technology allows you to select the Sleep state.
NOTE: If you have set a password to be required on wakeup, you must enter your Windows password before your work will return to the screen. Using the power meter and power settings The power meter is located in the notification area, at the far right of the taskbar. The power meter allows you to quickly access power settings and view the remaining battery charge. ● To display the percentage of remaining battery charge and the current power plan, point over the power meter icon.
Finding additional battery information Help and Support provides the following tools and information about the battery: ● Battery Check tool to test battery performance ● Information on calibration, power management, and proper care and storage to maximize battery life ● Information on battery types, specifications, life cycles, and capacity To access battery information: ▲ Select Start > Help and Support > Learn > Power Plans: Frequently Asked Questions.
Identifying low battery levels When a battery that is the sole power source for the computer reaches a low or critical battery level, the following behavior occurs: ● The battery light (select models only) indicates a low or critical battery level. – or – ● The power meter icon in the notification area shows a low or critical battery notification. NOTE: For additional information about the power meter, see Using the power meter and power settings on page 37.
CAUTION: Removing a battery that is the sole power source for the computer can cause loss of information. To prevent loss of information, save your work and shut down the computer through Windows before removing the battery. 1. Turn the computer upside down on a flat surface, with the battery bay away from you. 2. Slide the battery release latch (1) to release the battery. 3. Pivot the battery up (2), and then remove the battery from the computer (3).
Replacing a user-replaceable battery (select models only) Battery Check notifies you to replace the battery when an internal cell is not charging properly or when the battery storage capacity has reached a weak condition. If the battery is possibly covered by an HP warranty, instructions include a warranty ID. A message refers you to the HP website for more information about ordering a replacement battery. Using external AC power WARNING! Do not charge the computer battery while you are onboard aircraft.
3. Connect the AC adapter to the computer, and then plug it into an AC outlet. 4. Turn on the computer. ● If the power lights turn on, the AC adapter is working properly. ● If the power lights remain off, the AC adapter is not functioning and should be replaced. Contact support for information on obtaining a replacement AC power adapter. Switchable graphics/dual graphics (select models only) Select computers are equipped with either switchable graphics or dual graphics.
Using dual graphics (select models only) If your system is equipped with dual graphics (two or more added Graphics Processing Units (GPUs), you can enable AMD Radeon Dual Graphics to increase application power and performance for fullscreen applications that use DirectX version 10 or 11. For more information about DirectX, see http://www.microsoft.com/directx.
7 External cards and devices Using memory cards (select models only) Optional memory cards provide secure data storage and convenient data sharing. These cards are often used with digital media-equipped cameras and PDAs as well as with other computers. To determine the memory card formats that are supported on your computer, see Getting to know your computer on page 4. Inserting a memory card CAUTION: To reduce the risk of damage to the memory card connectors, use minimal force to insert a memory card.
3. Press in on the card (1), and then remove it from the slot (2). NOTE: If the card does not eject, pull the card out of the slot. Using ExpressCards (select models only) An ExpressCard is a high-performance PC Card that is inserted into the ExpressCard slot. ExpressCards are designed to conform to the standard specifications of the Personal Computer Memory Card International Association (PCMCIA). Configuring an ExpressCard Install only the software required for the card.
Inserting an ExpressCard CAUTION: To prevent damage to the computer and external memory cards, do not insert a PC Card into an ExpressCard slot. CAUTION: To reduce the risk of damage to the connectors: Use minimal force when inserting an ExpressCard. Do not move or transport the computer when an ExpressCard is in use. NOTE: The following illustration may look slightly different than your device. The ExpressCard slot may contain a protective insert. To remove the insert: 1.
Removing an ExpressCard CAUTION: To reduce the risk of loss of data or an unresponsive system, use the following procedure to safely remove the ExpressCard. 1. Save your information and close all programs associated with the ExpressCard. 2. Click the remove hardware icon on the Windows desktop in the notification area, at the far right of the taskbar, and then follow the on-screen instructions. 3. Release and remove the ExpressCard: a. Gently press in on the ExpressCard (1) to unlock it. b.
Inserting a smart card 1. Hold the card label-side up, and gently slide the card into the smart card reader until the card is seated. 2. Follow the on-screen instructions for logging on to the computer using the smart card PIN. Removing a smart card ▲ Grasp the edge of the smart card, and then pull it out of the smart card reader.
Connecting a USB device CAUTION: To reduce the risk of damage to a USB connector, use minimal force to connect the device. ▲ Connect the USB cable for the device to the USB port. NOTE: The following illustration may look slightly different than your computer. You will hear a sound when the device has been detected. NOTE: The first time you connect a USB device, a message in the notification area lets you know that the device is recognized by the computer.
CAUTION: To reduce the risk of damage to the equipment when connecting a powered device, be sure that the device is turned off and the AC power cord is unplugged. 1. Connect the device to the computer. 2. If you are connecting a powered device, plug the device power cord into a grounded AC outlet. 3. Turn off the device. To disconnect an unpowered external device, turn off the device, and then disconnect it on the computer.
8 Drives Handling drives CAUTION: Drives are fragile computer components that must be handled with care. Refer to the following cautions before handling drives. Do not drop a drive, place items on it, or expose it to liquids, or temperature or humidity extremes. Observe these precautions when handling drives: ● Before removing or installing a drive, shut down the computer.
This provides the advantage of having a hard disk drive (or a RAID volume) for maximum storage capacity while simultaneously delivering SSD enhanced system performance experience. If you add or upgrade a hard drive and intend to set a RAID volume, you must temporarily disable SRT, set the RAID volume, and then enable SRT. To temporarily disable SRT: 1. Select Start > All Programs > Intel > Intel Rapid Storage Technology. 2.
Replacing the service cover Replace the service cover after accessing the memory module slot, hard drive, regulatory label, and other components. 1. Tilt the service cover down to align the front edge of the service cover near the front edge of the computer (1). 2. Insert the alignment tabs (2) on the front edge of the service cover with the notches on the computer. 3. Slide the service cover toward the battery bay until the service cover snaps into place. 4.
Removing the hard drive To remove a hard drive: 1. Save your work. 2. Shut down the computer and close the display. 3. Disconnect AC power and all external hardware devices from the computer. 4. Turn the computer upside down on a flat surface. 5. Remove the battery. (See Replacing a user-replaceable battery (select models only) on page 41). 6. Loosen the 3 hard drive screws (1). Pull the hard drive tab (2) to the left to disconnect the hard drive. 7.
2. Pull the plastic tab (2) toward the center of the computer to engage the hard drive with the connector. 3. Tighten the hard drive screws (3). 4. Replace the service cover (see Removing or replacing the service cover on page 52). 5. Replace the battery (see Inserting or removing the battery on page 39). 6. Connect AC power and external devices to the computer. 7. Turn on the computer.
To run Disk Defragmenter: 1. Connect the computer to AC power. 2. Select Start > All Programs > Accessories > System Tools > Disk Defragmenter. 3. Click Defragment disk. NOTE: Windows includes the User Account Control feature to improve the security of your computer. You may be prompted for your permission or password for tasks such as installing software, running utilities, or changing Windows settings. Refer to Help and Support. To access Help and Support, select Start > Help and Support.
drive is currently protected or whether it is parked, view the icon on the Windows desktop in the notification area, at the far right of the taskbar, or in the Mobility Center: ● If the software is actively protecting the drive, a green check mark is superimposed over the icon. ● If the software has been disabled, a no symbol ● If the software has parked the drive due to a shock event, an orange cone is superimposed over the icon. is superimposed over the icon.
9 Security Protecting the computer Standard security features provided by the Windows operating system and the non-Windows Computer Setup utility (BIOS) can protect your personal settings and data from a variety of risks. NOTE: Security solutions are designed to act as deterrents. These deterrents may not prevent a product from being mishandled or stolen. NOTE: Before you send your computer for service, back up and delete confidential files, and remove all password settings.
Passwords can be set in Windows or in the non-Windows Computer Setup utility that is preinstalled on the computer. ● BIOS administrator and DriveLock are set in Computer Setup and are managed by the system BIOS. ● Automatic DriveLock passwords are enabled in Computer Setup. ● Windows passwords are set only in the Windows operating system. ● If HP SpareKey has been set up previously, and if you forget the BIOS administrator password set in Computer Setup, you can use HP SpareKey to access the utility.
Setting passwords in Computer Setup Password Function BIOS administrator password* Protects access to Computer Setup. NOTE: If features have been enabled to prevent removing the BIOS administrator password, you may not be able to remove it until those features have been disabled. DriveLock master password* Protects access to the internal hard drive that is protected by DriveLock. It is also used to remove DriveLock protection. This password is set under DriveLock Passwords during the enable process.
4. When prompted, type your current password. 5. When prompted, type your new password again to confirm. 6. To save your changes and exit Computer Setup, click the Save icon in the lower-left corner of the screen, and then follow the on-screen instructions. – or – Use the arrow keys to select File > Save Changes and Exit, and then press enter. Your changes go into effect when the computer restarts. Deleting a BIOS administrator password 1.
To apply DriveLock protection to an internal hard drive, a user password and a master password must be set in Computer Setup. Note the following considerations about using DriveLock protection: ● After DriveLock protection is applied to a hard drive, the hard drive can be accessed only by entering either the user password or the master password. ● The owner of the user password should be the day-to-day user of the protected hard drive.
Entering a DriveLock password Be sure that the hard drive is inserted into the computer (not into an optional docking device or external MultiBay). At the DriveLock Password prompt, type your user or master password (using the same kind of keys you used to set the password), and then press enter. After 2 incorrect attempts to enter the password, you must shut down the computer and try again. Changing a DriveLock password To change a DriveLock password in Computer Setup, follow these steps: 1.
8. Type your master password, and then press enter. 9. To save your changes and exit Computer Setup, click the Save icon and then follow the onscreen instructions. – or – Use the arrow keys to select File > Save Changes and Exit, and then press enter. Your changes go into effect when the computer restarts. Using Computer Setup Automatic DriveLock In a multiple-user environment, you can set an Automatic DriveLock password.
6. Use a pointing device or the arrow keys to select Disable protection. 7. To save your changes and exit Computer Setup, click the Save icon in the lower-left corner of the screen, and then follow the on-screen instructions. – or – Use the arrow keys to select File > Save Changes and Exit, and then press enter. Using antivirus software When you use the computer to access email, a network, or the Internet, you potentially expose it to computer viruses.
Updates to the operating system and other software may have become available after the computer left the factory. To be sure that all available updates are installed on the computer, observe these guidelines: 1. Run Windows Update as soon as possible after you set up your computer. 2. Run Windows Update monthly thereafter. 3. Obtain updates to Windows and other Microsoft programs, as they are released, from the Microsoft website and through the updates link in Help and Support.
Using the fingerprint reader (select models only) Integrated fingerprint readers are available on select computer models. In order to use the fingerprint reader, you must enroll your fingerprints in the HP Client Security's Credential Manager. Refer to the HP Client Security software Help. After you enroll your fingerprints in Credential Manager, you can use HP Client Security's Password Manager to store and fill in your user names and passwords in supported websites and applications.
10 Maintenance Adding or replacing memory modules The computer has one memory module compartment. The capacity of the computer can be upgraded by adding one or more memory modules to the vacant expansion memory module slots or by upgrading the existing memory module in the primary memory module slot. WARNING! To reduce the risk of electric shock and damage to the equipment, unplug the power cord and remove all batteries before installing a memory module.
b. Grasp the edge of the memory module (2), and then gently pull the memory module out of the memory module slot. CAUTION: To prevent damage to the memory module, hold the memory module by the edges only. Do not touch the components on the memory module. To protect a memory module after removal, place it in an electrostatic-safe container. 6. Insert a new memory module: CAUTION: To prevent damage to the memory module, hold the memory module by the edges only.
c. Gently press the memory module (3) down, applying pressure to both the left and right edges of the memory module, until the retention clips snap into place. CAUTION: To prevent damage to the memory module, be sure that you do not bend the memory module. 7. Replace the service cover (see Removing or replacing the service cover on page 52). 8. Insert the battery (see Inserting or removing the battery on page 39). 9. Connect AC power and external devices to the computer. 10. Turn on the computer.
CAUTION: Avoid strong cleaning solvents that can permanently damage your computer. If you are not sure that a cleaning product is safe for your computer, check the product contents to make sure that ingredients such as alcohol, acetone, ammonium chloride, methylene chloride, and hydrocarbons are not included in the product. Fibrous materials, such as paper towels, can scratch the computer. Over time, dirt particles and cleaning agents can get trapped in the scratches.
recent gaming software. Without the latest driver, you would not be getting the most out of your equipment. Go to http://www.hp.com/support to download the latest versions of HP programs and drivers. In addition, register to receive automatic update notifications when they become available. Using SoftPaq Download Manager HP SoftPaq Download Manager (SDM) is a tool that provides quick access to SoftPaq information for HP business computers without requiring the SoftPaq number.
11 Backup and recovery Your computer includes HP and Windows tools to help you safeguard your information and retrieve it if you ever need to. These tools will help you return your computer to a proper working state, all with simple steps. This section provides information about the following processes: ● Creating recovery media and backups ● Restoring and recovering your system Creating recovery media and backups Recovery after a system failure is only as good as your most recent backup. 1.
well as select drivers and applications if the hard drive becomes corrupted. HP Recovery Disc Creator can create two kinds of recovery DVDs: ● Windows 7 operating system DVD—Installs the operating system without additional drivers or applications. ● Driver Recovery DVD—Installs specific drivers and applications only, in the same way that the HP Software Setup utility installs drivers and applications. Creating recovery media NOTE: The Windows 7 operating system DVD can be created only once.
To create a backup using Windows Backup and Restore: NOTE: The backup process may take over an hour, depending on file size and the speed of the computer. 1. Select Start > All Programs > Maintenance > Backup and Restore. 2. Follow the on-screen instructions to set up your backup, create a system image (select models only), or create system repair media (select models only).
CAUTION: Some Startup Repair options will completely erase and reformat the hard drive. All files you have created and any software installed on the computer are permanently removed. When reformatting is complete, the recovery process restores the operating system, as well as the drivers, software, and utilities from the backup used for recovery. 1. If possible, back up all personal files. 2. If possible, check for the presence of the Windows partition.
CAUTION: Using a Windows 7 operating system DVD completely erases hard drive contents and reformats the hard drive. All files that you have created and any software that you have installed on the computer are permanently removed. When reformatting is complete, the recovery process helps you restore the operating system, as well as drivers, software, and utilities. To initiate recovery using a Windows 7 operating system DVD: NOTE: This process takes several minutes. 1.
12 Computer Setup (BIOS), MultiBoot, and HP PC Hardware Diagnostics (UEFI) Using Computer Setup Computer Setup, or Basic Input/Output System (BIOS), controls communication between all the input and output devices on the system (such as disk drives, display, keyboard, mouse, and printer). Computer Setup includes settings for the types of devices installed, the startup sequence of the computer, and the amount of system and extended memory. NOTE: Use extreme care when making changes in Computer Setup.
To exit Computer Setup menus, choose one of the following methods: ● To exit Computer Setup menus without saving your changes: Click the Exit icon in the lower-right corner of the screen, and then follow the on-screen instructions. – or – Use the tab key and the arrow keys to select File > Ignore Changes and Exit, and then press enter. ● To save your changes and exit Computer Setup menus: Click the Save icon in the lower-right corner of the screen, and then follow the on-screen instructions.
Updating the BIOS Updated versions of the BIOS may be available on the HP website. Most BIOS updates on the HP website are packaged in compressed files called SoftPaqs. Some download packages contain a file named Readme.txt, which contains information regarding installing and troubleshooting the file.
BIOS installation procedures vary. Follow any instructions that are displayed on the screen after the download is complete. If no instructions are displayed, follow these steps: 1. Select Start > Computer. 2. Click your hard drive designation. The hard drive designation is typically Local Disk (C:). 3. Using the hard drive path you recorded earlier, open the folder on your hard drive that contains the update. 4. Double-click the file that has an .exe extension (for example, filename.exe).
Setting a new boot order in Computer Setup To start Computer Setup and set a boot device order that the computer uses each time it is turned on or restarted, follow these steps: 1. Turn on or restart the computer, and then press esc while the “Press the ESC key for Startup Menu” message is displayed at the bottom of the screen. 2. Press f10 to enter Computer Setup. 3. Use a pointing device or the arrow keys to select the Legacy Boot Order list, and then press enter. 4.
Use the arrow keys to select File > Save Changes and Exit, and then press enter. Your changes go into effect when the computer restarts. Entering MultiBoot Express preferences When the Express Boot menu is displayed during startup, you have the following choices: ● To specify a boot device from the Express Boot menu, select your preference within the allotted time, and then press enter.
Downloading HP PC Hardware Diagnostics (UEFI) to a USB device NOTE: only. The HP PC Hardware Diagnostics (UEFI) download instructions are provided in English 1. Go to http://www.hp.com. 2. Click Support & Drivers, and then click the Drivers & Software tab. 3. Enter the product name in the text box, and then click Search. 4. Select your computer model, and then select your operating system. 5. In the Diagnostic section, click HP UEFI Support Environment. – or – Click Download, and then select Run.
13 Support Contacting support If the information provided in this user guide or Help and Support does not address your questions, you can contact support. For U.S. support, go to http://www.hp.com/go/contactHP. For worldwide support, go to http://welcome.hp.com/country/us/en/wwcontact_us.html. Here you can: ● Chat online with an HP technician. NOTE: When support chat is not available in a particular language, it is available in English. ● Email support. ● Find support telephone numbers.
Labels The labels affixed to the computer provide information you may need when you troubleshoot system problems or travel internationally with the computer: ● Service label—Provides important information, including the following: Component (1) Product name (2) Serial number (s/n) (3) Part number/Product number (p/n) (4) Warranty period (5) Model description (select models only) Component (1) Warranty period (2) Model number (3) Serial number (4) Product number Have this information avai
● Wireless certification label or labels (select models only)—Provide information about optional wireless devices and the approval markings of some of the countries or regions in which the devices have been approved for use. If your computer model includes one or more wireless devices, one or more certification labels are included with your computer. You may need this information when traveling internationally. Wireless certification labels are affixed inside the battery bay.
14 Specifications Input power The power information in this section may be helpful if you plan to travel internationally with the computer. The computer operates on DC power, which can be supplied by an AC or a DC power source. The AC power source must be rated at 100–240 V, 50–60 Hz. Although the computer can be powered from a standalone DC power source, it should be powered only with an AC adapter or a DC power source supplied and approved by HP for use with this computer.
A Traveling with or shipping your computer If you have to travel with or ship your computer, here are some tips to keep in mind to keep your equipment safe. ● Prepare the computer for traveling or shipping: ◦ Back up your information to an external drive. ◦ Remove all discs and all external media cards, such as digital storage cards, from the computer. ◦ Turn off, and then disconnect all external devices. ◦ Shut down the computer. ● Take along a backup of your information.
B Troubleshooting The following sections are included in this appendix: Troubleshooting resources ● Access website links and additional information about the computer through Help and Support. To access Help and Support, select Start > Help and Support. NOTE: Some checkup and repair tools require an Internet connection. HP also provides additional tools that do not require an Internet connection. ● Contact HP support. For U.S. support, go to http://www.hp.com/go/contactHP.
The computer screen is blank If the screen is blank but you have not turned off the computer, one or more of these settings may be the cause: ● The computer may be in the Sleep state. To exit Sleep, briefly press the power button. Sleep is an energy-saving feature that turns off the display. Sleep can be initiated by the system while the computer is on but is not in use, or when the computer has reached a low battery level.
An external device is not working Follow these suggestions if an external device does not function as expected: ● Turn on the device according to the manufacturer's instructions. ● Be sure that all device connections are secure. ● Be sure that the device is receiving electrical power. ● Be sure that the device, especially if it is older, is compatible with the operating system. ● Be sure that the correct drivers are installed and updated.
A movie is not visible on an external display 1. If both the computer display and an external display are turned on, press fn+f4 one or more times to switch between the 2 displays. 2. Configure the monitor settings to make the external display primary: a. From the Windows desktop, right-click on a blank area of the computer desktop, and select Screen resolution. b. Specify a primary display and a secondary display.
C Electrostatic discharge Electrostatic discharge is the release of static electricity when two objects come into contact—for example, the shock you receive when you walk across the carpet and touch a metal door knob. A discharge of static electricity from fingers or other electrostatic conductors may damage electronic components.
Index A AC adapter, testing 41 AC adapter/battery light 11 accessory battery connector, identifying 13 administrator password 59 antivirus software 65 audio functions, checking 31 audio-in (microphone) jack, identifying 9 audio-out (headphone) jack, identifying 9 Automatic DriveLock password entering 64 removing 64 B Backup and Restore 75 backup tools 73 backups creating 74 recovering 75 battery conserving power 40 discharging 38 displaying remaining charge 38 disposing 40 low battery levels 38 replacing 41
fingerprint reader, identifying firewall software 65 fn key, identifying 7, 28 function keys, identifying 7 G GPS 21 graphics modes, switching 7 42 H hard drive external 50 HP 3D DriveGuard 56 installing 54 removing 54 hard drive light 8 hard drive recovery 76 hard drive, identifying 14 headphone (audio-out) jack 9 Hibernation exiting 36 initiating 36 high-definition devices, connecting 34 hot keys adjusting volume 28, 29 decrease screen brightness 29 decreasing speaker sound 28 description 28 increase s
optical drive, identifying 9 optional external devices, using 49 restoring the hard drive 76 RJ-45 (network) jack, identifying 11 rotating TouchPad gesture 26 P passwords administrator 59 BIOS administrator 60 DriveLock 61 user 59 pinching TouchPad gesture 26 pointing devices, setting preferences 23 pointing stick 4 ports DisplayPort 33 Dual-Mode DisplayPort 10 external monitor 9, 32 Intel Wireless Display 34 Thunderbolt 10 USB 9, 10 VGA 32 power battery 37 conserving 40 options 35 power button 35 power b
buttons 30 keys 30 volume keys, identifying 28, 29 W webcam 12, 31 webcam, identifying 12 Windows 7 operating system DVD creating 73 using for restore 76 Windows 7 operating system media creating 73 using for restore 76 Windows button, identifying 7 Windows Startup Repair, using 75 wireless button 15 wireless certification label 87 wireless controls button 15 operating system 15 wireless light 5, 15 wireless network (WLAN) connecting 19 corporate WLAN connection 19 equipment needed 18 functional range 19
