Maintenance and Service Guide HP HP HP HP ProDesk ProDesk ProDesk ProDesk 400 480 490 400 G1 G1 G1 G1 Microtower Microtower Microtower Small Form Factor
© Copyright 2013, 2014 Hewlett-Packard Development Company, L.P. The information contained herein is subject to change without notice. Microsoft and Windows are U.S. registered trademarks of the Microsoft group of companies. The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty.
About This Book WARNING! Text set off in this manner indicates that failure to follow directions could result in bodily harm or loss of life. CAUTION: Text set off in this manner indicates that failure to follow directions could result in damage to equipment or loss of information. NOTE: Text set off in this manner provides important supplemental information.
iv About This Book
Table of contents 1 Product features ............................................................................................................... 1 Standard configuration features ................................................................................................. 1 Microtower .............................................................................................................. 1 Small Form Factor ......................................................................................
Drives .................................................................................................................... 19 Misc boards ........................................................................................................... 19 Sequential part number listing ................................................................................... 20 Small Form Factor chassis spare parts .......................................................................................
Front bezel ............................................................................................................................ 44 Bezel blanks .......................................................................................................................... 45 Memory ................................................................................................................................ 47 DIMMs ........................................................................................
Installing DIMMs ..................................................................................................... 98 Expansion card .................................................................................................................... 100 System board connections ..................................................................................................... 104 Drives ....................................................................................................................
Solving audio problems ........................................................................................................ 169 Solving printer problems ....................................................................................................... 171 Solving keyboard and mouse problems .................................................................................. 172 Solving Hardware Installation Problems ..................................................................................
System Recovery ................................................................................................... 216 System Recovery when Windows is responding ......................................... 216 System Recovery when Windows is not responding .................................... 217 System Recovery using recovery media (select models only) ......................... 217 Using HP Recovery Disc operating system discs (select models only) ............. 218 Appendix A Battery replacement ...........
1 Product features Standard configuration features Features may vary depending on the model. For a complete listing of the hardware and software installed in the computer, run the diagnostic utility (included on some computer models only).
Small Form Factor 2 Chapter 1 Product features
Front panel components Microtower (model 400/490) Drive configuration may vary by model. Some models have a bezel blank covering one or more drive bays. 1 5.25-inch Optical Drive (optional) 6 Microphone Connector 2 5.25-inch Half-Height Drive Bay (behind bezel) 7 Hard Drive Activity Light 3 3.5-inch Media Card Reader (optional) 8 USB 3.0 Ports (blue) 4 Dual-State Power Button 9 Headphone Connector 5 USB 2.0 Ports (black) NOTE: The Power On Light is normally white when the power is on.
Small form factor Drive configuration may vary by model. Some models have a bezel blank covering one or more drive bays. 1 Slim Optical Drive (optional) 5 Headphone Connector 2 USB 2.0 Ports (black) 6 Dual-State Power Button 3 USB 3.0 Ports (blue) 7 Hard Drive Activity Light 4 Microphone Connector 8 3.5-inch Media Card Reader (optional) NOTE: The Power On Light is normally white when the power is on.
Rear panel components Microtower (model 400) 1 Power Cord Connector 7 Line-Out Connector for powered audio devices (green) 2 Power Indicator Light 8 Voltage Select Switch 3 PS/2 Keyboard Connector (purple) 9 PS/2 Mouse Connector (green) 4 Serial Connector 10 RJ-45 Network Connector 5 USB 2.0 Ports (black) 11 VGA Monitor Connector 6 DVI-D Monitor Connector 12 Line-In Audio Connector (blue) NOTE: An optional second serial port and an optional parallel port are available from HP.
Microtower (model 490) 1 Power Cord Connector 8 Line-Out Connector for powered audio devices (green) 2 Power Indicator Light 9 Voltage Select Switch 3 PS/2 Keyboard Connector (purple) 10 PS/2 Mouse Connector (green) 4 Serial Connector 11 RJ-45 Network Connector 5 USB 3.0 Ports (blue) 12 VGA Monitor Connector 6 USB 2.0 Ports (black) 13 Optional DisplayPort 7 DVI-D Monitor Connector 14 Line-In Audio Connector (blue) NOTE: HP.
Small form factor 1 PS/2 Mouse Connector (green) 6 Power Cord Connector 2 RJ-45 Network Connector 7 PS/2 Keyboard Connector (purple) 3 Serial Connector 8 DVI-D Monitor Connectors 4 USB 2.0 Ports (black) 9 VGA Monitor Connector 5 Line-In Audio Connector (blue) 10 Line-Out Connector for powered audio devices (green) NOTE: An optional second serial port and an optional parallel port are available from HP.
Serial number location Each computer has a unique serial number and a product ID number that are located on the exterior of the computer. Keep these numbers available for use when contacting customer service for assistance.
2 Activating and Customizing the Software NOTE: This chapter provides information for both Windows 7 and Windows 8. Activating and customizing the software in Windows 7 If your computer was not shipped with a Windows® operating system, some portions of this documentation do not apply. Additional information is available in online help after you activate the operating system. CAUTION: Do not add optional hardware or third-party devices to the computer until the operating system is successfully activated.
Downloading Windows 7 updates Microsoft may release updates to the operating system. To help keep the computer running optimally, HP recommends checking for the latest updates during the initial installation and periodically throughout the life of the computer. 1. To set up your Internet connection, click Start > Internet Explorer and follow the instructions on the screen. 2. After an Internet connection has been established, click the Start > All Programs > Windows Update. 3.
We recommend that you register your computer with HP during operating system set up so you can receive important software updates, facilitate support questions, and sign up for special offers. You can also register your computer with HP using the Register with HP app on the Start screen. CAUTION: After the activation process has begun, DO NOT TURN OFF THE COMPUTER UNTIL THE PROCESS IS COMPLETE.
3 Illustrated parts catalog This chapter provides spare part information for all chassis. NOTE: HP continually improves and changes product parts. For complete and current information on supported parts for your computer, go to http://partsurfer.hp.com, select your country or region, and then follow the on-screen instructions.
Microtower chassis spare parts Computer major components Microtower chassis spare parts 13
Item Description (1) Front bezel Spare part number For use in all countries and regions except for the People’s Republic of China 745047-001 For use in the People’s Republic of China 745048-001 (2) Access panel 745046-001 (3) Power supply 300W, Energy Star 5.0 712298-001 300W, Energy Star 6.
Item Description Spare part number Intel Core i7 4771 (3.5-GHz, 8-MB L3 cache), 84W 742563-001 Intel Core i7 4770 (3.4-GHz, 8-MB L3 cache), 84W 727373-001 Intel Core i7 4770s (3.1-GHz, 8-MB L3 cache), 65W 732507-001 Intel Core i5 4670 (3.4-GHz, 6-MB L3 cache), 84W 727381-001 Intel Core i5 4670s (3.1-GHz, 6-MB L3 cache), 65W 732506-001 Intel Core i5 4570 (3.2-GHz, 6-MB L3 cache), 84W 727380-001 Intel Core i5 4570s (2.9-GHz, 6-MB L3 cache), 65W 732505-001 Intel Core i5 4430 (3.
Cables 16 Item Description Spare part number (1) Front I/O assembly 745049-001 (2) Power switch/LED assembly 745050-001 SATA data cable, 14 inch, 2 straight ends 745051-001 DMS-59 to dual VGA cable 463023-001 DMS-59 to dual DVI cable 463024-001 Adapter, DisplayPort to VGA 632484-001 Adapter, DisplayPort to DVI 662723-001 Adapter, DisplayPort to HDMI 617450-001 Adapter, DVI to VGA 657401-001 Adapter, DVI-I to VGA (BFR/PVC free) 720216-001 Adapter, DVI-I to VGA (Standard) 202997-00
Misc parts Item Description (1) Fan sink (includes replacement thermal material) Spare part number For use in 400 and 490 models, standard 745054-001 For use in 490 models, BFR/PVC free 748826-001 (2) Speaker 745053-001 (3) Fan Standard 745052-001 Fan, BFR/PVC free 748825-001 Microtower chassis spare parts 17
Item Description Spare part number (4) Serial port, PCI card 638815-001 (5) DisplayPort connector module (for use only in 490 MT models) 735966-001 Printer port, PCI card 638817-001 Card reader 14-in-1, USB 3.0, 3.5-inch, UHS-I 716390-001 15-in-1, USB 3.0, 3.5-inch, UHS-II 736299-001 Adapter, USB 3.0 to 2.0 736835-001 Optical drive bezel blank 745036-001 HP Ultraslim Keyed Cable Lock 703372-001 Hard drive carrier, 2.5-inch to 3.
Drives Description Spare part number Hard drive 2 TB, 7200 rpm, 3.5 inch 747993-001 1 TB, hybrid SSD 724937-001 1 TB, 7200 rpm, 3.5 inch 747992-001 500 GB, 7200 rpm, 3.
Sequential part number listing 20 Spare part number Description 202997-001 Adapter, DVI-I to VGA (standard) 397117-001 Hard drive adapter bracket (to install 2.5” or 3.5” hard drives into 5.25 drive bay) 450712-001 Grommet, hard drive 463023-001 DMS-59 to dual VGA cable 463024-001 DMS-59 to dual DVI cable 487562-001 DisplayPort cable 583345-001 WLAN antennas 586721-001 Drive adapter, 2.
Spare part number Description 702084-001 Nvidia GeForce GT630 DP PCIe x16 graphics card, 2 GB 703372-001 HP Ultraslim Keyed Cable Lock 703597-001 Hard drive carrier, 2.5-inch to 3.5-inch 707252-001 Nvidia NVS310 PCIe x16 graphics card, 512 MB 709695-xx1 Keyboard, unbranded 712298-001 Power supply for use in the microtower, 300W, Energy Star 5.
22 Spare part number Description 729339-001 Keyboard, USB, unbranded, Katydid 730323-xx1 Wireless keyboard, mouse, and dongle kit (for use in all countries except for Brazil) 732505-001 Intel Core i5 4570s processor (2.9-GHz, 6-MB L3 cache), 65W 732506-001 Intel Core i5 4670s processor (3.1-GHz, 6-MB L3 cache), 65W 732507-001 Intel Core i7 4770s processor (3.
Spare part number Description 747910-501 System board for use in 480 G1 models with Windows 8 Standard (includes replacement thermal material) 747910-601 System board for use in 480 G1 models with Windows 8 Professional (includes replacement thermal material) 747992-001 1 TB, 7200 rpm hard drive, 3.5 inch 747993-001 2 TB, 7200 rpm SATA hard drive, 3.5 inch 748824-001 Power supply for use in the microtower, 300W, Energy Star 6.
Small Form Factor chassis spare parts Computer major components Item Description Spare part number (1) Front bezel 745039-001 (2) Access panel 745042-001 (3) Power supply (4) 240W, 85% efficient 722536-001 240W, standard 702457-001 System board (includes replacement thermal material) For use in models without Windows 8 24 Chapter 3 Illustrated parts catalog 718414-001
Item Description Spare part number For use in models with Windows 8 Standard 718414-501 For use in models with Windows 8 Professional 718414-601 For use in models with NetClone (the People’s Republic of China only) 745239-001 Memory modules (PC3,12800, CL11) 8-GB 689375-001 4-GB 671613-001 2-GB 671612-001 Processors (include replacement thermal material) Intel Core i7 4771 (3.5-GHz, 8-MB L3 cache), 84W 742563-001 Intel Core i7 4770 (3.
Cables 26 Item Description Spare part number (1) Front I/O assembly 745037-001 (2) Power switch assembly 745038-001 SATA drive power cable 745040-001 SATA data cable, 19.5 inch, 2 straight ends 745044-001 SATA data cable, 14.
Misc parts Item Description Spare part number (1) Fan sink (includes replacement thermal material) 745661-001 (2) Speaker 727149-001 (3) Printer port, PCI card 638817-001 (4) Fan duct 727145-001 (5) Serial port, PCI card 638815-001 Card reader Card reader, 14-in-1, USB 3.0, 3.5-inch, UHS-I 716390-001 Card reader, 15-in-1, USB 3.0, 3.5-inch, UHS-II 736299-001 Adapter, USB 3.0 to 2.
Item Description Spare part number Hard drive adapter bracket (to install 2.5” or 3.5” hard drives into 5.
Description Spare part number 120-GB Solid-state drive 756459-001 20-GB Solid-state Drive (SSD) 683305-001 Optical drive Blu-ray BD-RW SuperMulti XL Drive 719157-001 DVD±RW drive 657958-001 DVD-ROM drive 608394-001 NOTE: 2.5-inch solid-state drives require an adapter for installation.
30 Spare part number Description 638817-001 Printer port, PCI card 657401-001 Adapter, DVI to VGA 657958-001 DVD±RW drive 662723-001 Adapter, DisplayPort to DVI 665961-001 128-GB Solid-state drive 671612-001 Memory module, 2-GB, PC3 12800 671613-001 Memory module, 4-GB, PC3-12800 674315-001 Mouse, PS2, optical 674316-001 Mouse, USB, optical 674317-001 Mouse, wireless, HP Elite (for use only in Brazil) 674318-001 Mouse, USB, HP Elite 680020-001 256-GB Solid-state drive, self-encrypt
Spare part number Description 722536-001 Power supply, 240W, 85% efficient 724718-xx1 Keyboard, PS/2, for use in models with Windows 8 724720-xx1 Keyboard, USB, black, for use in models with Windows 8 724722-201 Keyboard, wireless, HP Elite with USB dongle (for use only in Brazil) 724795-001 Mouse, washable 724937-001 1 TB hard drive, hybrid SSD 724938-001 500 GB hard drive, hybrid SSD 727145-001 Fan duct 727149-001 Speaker 727373-001 Intel Core i7 4770 processor (3.
32 Spare part number Description 745042-001 Access panel 745239-001 System board for use in models with NetClone (includes replacement thermal material) (the People’s Republic of China only) 745044-001 Optical drive SATA cable, 19.5 inch, 2 straight ends 745045-001 SATA data cable, 14.0 inch, 1 straight end, 1 right angle 745661-001 Fan sink 745668-001 Intel Dual Band Wireless-N 7260 802.11 a/b/g/n (2x2) Wireless NIC 747992-001 1 TB, 7200 rpm hard drive, 3.
4 Routine care, SATA drive guidelines, and disassembly preparation This chapter provides general service information for the computer. Adherence to the procedures and precautions described in this chapter is essential for proper service. CAUTION: When the computer is plugged into an AC power source, voltage is always applied to the system board. You must disconnect the power cord from the power source before opening the computer to prevent system board or component damage.
Generating static The following table shows that: ● Different activities generate different amounts of static electricity. ● Static electricity increases as humidity decreases.
Personal grounding methods and equipment Use the following equipment to prevent static electricity damage to equipment: ● Wrist straps are flexible straps with a maximum of one-megohm ± 10% resistance in the ground cords. To provide proper ground, a strap must be worn snug against bare skin. The ground cord must be connected and fit snugly into the banana plug connector on the grounding mat or workstation.
● Conductive foam ● Conductive tabletop workstations with ground cord of one-megohm +/- 10% resistance ● Static-dissipative table or floor mats with hard tie to ground ● Field service kits ● Static awareness labels ● Wrist straps and footwear straps providing one-megohm +/- 10% resistance ● Material handling packages ● Conductive plastic bags ● Conductive plastic tubes ● Conductive tote boxes ● Opaque shielding bags ● Transparent metallized shielding bags ● Transparent shielding tub
● Never cover the ventilation slots on the monitor with any type of material. ● Install or enable power management functions of the operating system or other software, including sleep states. Routine care General cleaning safety precautions 1. Never use solvents or flammable solutions to clean the computer. 2. Never immerse any parts in water or cleaning solutions; apply any liquids to a clean cloth and then use the cloth on the component. 3.
CAUTION: Use safety glasses equipped with side shields before attempting to clean debris from under the keys. ● Visible debris underneath or between the keys may be removed by vacuuming or shaking. ● Canned, pressurized air may be used to clean debris from under the keys. Caution should be used as too much air pressure can dislodge lubricants applied under the wide keys. ● If you remove a key, use a specially designed key puller to prevent damage to the keys.
Tools and software Requirements To service the computer, you need the following: ● Torx T-15 screwdriver ● Torx T-15 screwdriver with small diameter shank (for certain front bezel removal) ● Flat-bladed screwdriver (may sometimes be used in place of the Torx screwdriver) ● Phillips #2 screwdriver ● Diagnostics software ● Tamper-resistant T-15 wrench Screws The screws used in the computer are not interchangeable. They may have standard or metric threads and may be of different lengths.
● If you are inserting or removing a hard drive, turn off the computer. Do not remove a hard drive while the computer is on or in standby mode. ● Before handling a drive, ensure that you are discharged of static electricity. While handling a drive, avoid touching the connector. ● Do not use excessive force when inserting a drive. ● Avoid exposing a hard drive to liquids, temperature extremes, or products that have magnetic fields such as monitors or speakers.
SATA hard drive cables SATA data cable Always use an HP approved SATA 6.0 Gb/s cable as it is fully backwards compatible with the SATA 1.5 Gb/s drives. Current HP desktop products ship with SATA 6.0 Gb/s hard drives. SATA data cables are susceptible to damage if overflexed. Never crease a SATA data cable and never bend it tighter than a 30 mm (1.18 in) radius. The SATA data cable is a thin, 7-pin cable designed to transmit data for only a single drive.
5 Removal and replacement procedures: Microtower Adherence to the procedures and precautions described in this chapter is essential for proper service. After completing all necessary removal and replacement procedures, run the Diagnostics utility to verify that all components operate properly. NOTE: Not all features listed in this guide are available on all computers. NOTE: HP continually improves and changes product parts.
Access panel Description Spare part number Access panel 745046-001 To access internal components, you must remove the access panel: 1. Prepare the computer for disassembly (Preparation for disassembly on page 42). 2. Loosen the two thumbscrews on the rear of the computer (1) then slide the panel back (2) and lift if off the computer (3).
Front bezel 44 Description Spare part number Front bezel for use in all countries and regions except for the People’s Republic of China 745047-001 Front bezel for use in the People’s Republic of China 745048-001 1. Prepare the computer for disassembly (Preparation for disassembly on page 42). 2. Remove the access panel (Access panel on page 43) 3. Lift up the three tabs on the side of the bezel (1), then rotate the bezel off the chassis (2).
Bezel blanks Description Spare part number Bezel blank 745036-001 On some models, there are bezel blanks covering the 3.5-inch and 5.25-inch drive bays that need to be removed before installing a drive. To remove a bezel blank: 1. Remove the access panel (Access panel on page 43) 2. Remove the front bezel (Front bezel on page 44) 3. Remove the bezel blank for the appropriate drive: ● To remove a 5.
● 46 To remove a 3.5-inch bezel blank, press inward on the two retaining tabs on the side of the bezel blank that hold the bezel blank in place (1) and rotate the bezel blank back to remove it (2).
Memory Description Spare part number 8-GB, PC3-12800 689375-001 4-GB, PC3-12800 671613-001 2-GB, PC3-12800 671612-001 The computer comes with double data rate 3 synchronous dynamic random access memory (DDR3SDRAM) dual inline memory modules (DIMMs). DIMMs The memory sockets on the system board can be populated with up to two industry-standard DIMMs (model 400) or four industry-standard DIMMs (model 490) . These memory sockets are populated with at least one preinstalled DIMM.
Populating DIMM sockets (Model 400) There are two DIMM sockets on the system board, with one socket per channel. The sockets are labeled DIMM1 and DIMM3. Socket DIMM1 operates in memory channel B. Socket DIMM3 operates in memory channel A. The system will automatically operate in single channel mode, dual channel mode, or flex mode, depending on how the DIMMs are installed. NOTE: Single channel and unbalanced dual channel memory configurations will result in inferior graphics performance.
A. For example, if you are populating the sockets with one 2-GB DIMM, and three 1-GB DIMMs, Channel A should be populated with the 2-GB DIMM and one 1-GB DIMM, and Channel B should be populated with the other two 1-GB DIMMs. With this configuration, 4-GB will run as dual channel and 1-GB will run as single channel. ● In any mode, the maximum operational speed is determined by the slowest DIMM in the system.
4. Push the module down into the socket, ensuring that the module is fully inserted and properly seated. Make sure the latches are in the closed position (3). 5. Repeat steps 3 and 4 to install any additional modules. The computer should automatically recognize the additional memory the next time you turn on the computer.
Expansion cards Description Spare part number Nvidia NVS310 PCIe x16 graphics card, 512 MB 707252-001 Nvidia NVS315 PCIe x16 graphics card, 1 GB 720837-001 AMD Radeon HD8490 DP PCIe x16 graphics card, 1 GB 717219-001 AMD Radeon HD8470 PCIe x16 graphics card, 2 GB (for use only in the People’s Republic of China) 702085-001 AMD Radeon HD8350 DH PCIe x16 graphics card, 1 GB DDR3 717220-001 Nvidia GeForce GT630 DP PCIe x16 graphics card, 2 GB 702084-001 AMD Radeon HD8350 PCIe x16 graphics card, 1
3. Remove the screw that holds down the expansion card retention latch (1) then slide the latch up (2) and pull it off the rear of the chassis (3). 4. Locate the correct vacant expansion socket on the system board and the corresponding expansion slot on the back of the computer chassis. 5. Before installing an expansion card, remove the expansion slot cover or the existing expansion card.
NOTE: System board appearance and PCI expansion sockets may vary. a. If you are installing an expansion card in a vacant socket, you must slide one of the expansion slot covers up and out of the chassis or use a flatblade screwdriver to pry out one of the metal shields on the rear panel that covers the expansion slot. Be sure to remove the appropriate shield for the expansion card you are installing. b.
c. If you are removing a PCI Express x16 card, pull the retention arm on the back of the expansion socket away from the card and carefully rock the card back and forth until the connectors pull free from the socket. Lift the card straight up then away from the inside of the chassis to remove it. Be sure not to scrape the card against other components. 6. Store the removed card in anti-static packaging. 7.
8. To install a new expansion card, hold the card just above the expansion socket on the system board then move the card toward the rear of the chassis (1) so that the bottom of the bracket on the card slides into the small slot on the chassis. Press the card straight down into the expansion socket on the system board (2). NOTE: When installing an expansion card, press firmly on the card so that the whole connector seats properly in the expansion card slot. 9.
System board connections – model 400 Refer to the following illustration and table to identify the system board connectors for your model. 56 No.
System board connections – model 480 Refer to the following illustration and table to identify the system board connectors for your model. No.
No. System Board Connector System Board Label Color Component 13 Parallel Port PAR black Optional Parallel Port 14 USB 2.0 USB black USB 2.0 Device, such as a Media Card Reader System board connections – model 490 Refer to the following illustration and table to identify the system board connectors for your model. 58 No.
No. System Board Connector System Board Label Color Component 13 SATA 3.0 SATA0 dark blue Primary Hard Drive 14 SATA 3.0 SATA1 light blue Any SATA Device other than the Primary Hard Drive 15 Parallel Port PAR black Optional Parallel Port 16 USB 3.0 MEDIA 3.0 black USB 3.0 Device, such as a Media Card Reader 17 USB 2.0 MEDIA black USB 2.
When installing drives, follow these guidelines: Model 400: ● The primary Serial ATA (SATA) hard drive must be connected to the dark blue primary SATA connector on the system board labeled SATA0. ● Connect a secondary hard drive to the light blue SATA connector on the system board labeled SATA1. ● Connect optical drives to the white SATA connectors on the system board labeled SATA4 and SATA5. ● Connect a media card reader USB 3.0 cable to a USB 3.0 to USB 2.
No. Mounting Screw Device 1 Silver Standard 6-32 Mounting Screws USB 3.0 Media Card Reader 3.5-inch Hard Drive 2 Black M3 Mounting Screws 5.25-inch Optical Drive CAUTION: To prevent loss of work and damage to the computer or drive: If you are inserting or removing a drive, shut down the operating system properly, turn off the computer, and unplug the power cord. Do not remove a drive while the computer is on or in standby mode.
Drive positions 1 5.25-inch half-height drive bay (optical drive shown) 2 5.25-inch half-height drive bay 3 3.5-inch drive bay for optional drive (media card reader shown) 4 Primary 3.5-inch internal hard drive bay 5 Secondary 3.5-inch internal hard drive bay NOTE: The drive configuration on your computer may be different than the drive configuration shown above. To verify the type and size of the storage devices installed in the computer, run Computer Setup.
Removing a 5.25-inch drive CAUTION: All removable media should be taken out of a drive before removing the drive from the computer. 1. Prepare the computer for disassembly (Preparation for disassembly on page 42) 2. Remove the access panel (Access panel on page 43) 3. Remove the front bezel (Front bezel on page 44) 4. Disconnect the power cable and data cable from the back of the drive.
4. If you are installing an optical drive, install one black M3 metric mounting screw in the front upper screw hole on the right side of the drive. NOTE: HP has supplied three extra M3 mounting screws on the front of the chassis behind the bezel. Refer to Drives on page 59 for an illustration of the extra mounting screws location. When replacing an optical drive, transfer the M3 mounting screw from the old drive to the new one. CAUTION: Use only 5-mm long screws as mounting screws.
6. Connect the power cable (1) and data cable (2) to the back of the hard drive. NOTE: The power cable for the hard drives is a two-headed cable that is routed from the power supply to the rear of the hard drive bays. 7. Connect the opposite end of the data cable to one of the white (model 400) or light blue (model 490) SATA connectors on the system board.
66 4. Disconnect the drive cables from the rear of the drive, or, if you are removing a media card reader, disconnect the USB cable from the system board as indicated in the following illustration. 5. Remove the two silver 6-32 mounting screws from the side of the device (1) and slide the device out of the front of the drive bay (2).
Installing a 3.5-inch device (model 400) 1. Prepare the computer for disassembly (Preparation for disassembly on page 42). 2. Remove the access panel (Access panel on page 43). 3. Remove the front bezel (Front bezel on page 44). Remove the front bezel. If you are installing a drive in a bay covered by a bezel blank, remove the bezel blank. 4. Slide the device into the drive bay (1) and install the two 6-32 mounting screws in the side of the device (2) to secure it in place.
5. If installing a USB 3.0 media card reader, connect the media card reader 3.0 cable to the USB 3.0 to USB 2.0 adapter (1) and connect the adapter to the connector on the system board labeled MEDIA (2). NOTE: Refer to System board connections – model 400 on page 56 or System board connections – model 480 on page 57 for an illustration of the system board drive connectors.
Installing a 3.5-inch device (model 480 and model 490) 1. Prepare the computer for disassembly (Preparation for disassembly on page 42). 2. Remove the access panel (Access panel on page 43). 3. Remove the front bezel (Front bezel on page 44). Remove the front bezel. If you are installing a drive in a bay covered by a bezel blank, remove the bezel blank. 4. Slide the device into the drive bay (1) and install the two 6-32 mounting screws in the side of the device (2) to secure it in place.
5. If installing a USB 3.0 media card reader, connect the media card reader cable to the USB 3.0 connector on the system board labeled MEDIA 3.0. NOTE: Refer to System board connections – model 400 on page 56 or System board connections – model 480 on page 57 for an illustration of the system board drive connectors. Removing a 3.5-inch hard drive NOTE: Before you remove the old hard drive, be sure to back up the data from the old hard drive so that you can transfer the data to the new hard drive. 70 1.
Installing a 3.5-inch drive 1. Prepare the computer for disassembly (Preparation for disassembly on page 42) 2. Remove the access panel (Access panel on page 43) 3. You can install a 3.5-inch hard drive or a 2.5-inch hard drive with a 3.5-inch adapter bracket similar to the example shown below. ● Slide the drive into the bay adapter bracket, ensuring the connector on the drive is fully inserted into the connector on the adapter bracket.
4. Slide the drive into the drive bay (1) and install the four 6-32 mounting screws (2) to secure the drive in place. NOTE: HP has supplied four extra 6-32 mounting screws on the front of the chassis behind the bezel. Refer to Drives on page 59 for an illustration of the extra mounting screws location. When replacing a hard drive, use the four 6-32 mounting screws that were removed from the old drive to install the new one.
5. Connect the power cable (1) and data cable (2) to the back of the hard drive. NOTE: The power cable for the hard drives is a two-headed cable that is routed from the power supply to the rear of the hard drive bays. 6. If installing a new drive, connect the opposite end of the data cable to the appropriate system board connector. NOTE: You must connect the primary hard drive data cable to the dark blue connector labeled SATA0 to avoid any hard drive performance problems.
DisplayPort connector module (480 MT and 490 MT models only) 74 Description Spare part number DisplayPort connector module (for use only in 490 MT models) 735966-001 1. Prepare the computer for disassembly (Preparation for disassembly on page 42). 2. Remove the access panel (Access panel on page 43). 3. Remove the front bezel (Front bezel on page 44). 4. From the outside, rear of the computer, remove the Torx T15 screw that secures the DisplayPort module to the computer.
5. From the inside of the computer, pull the module straight up to disengage it from the system board connector. To reinstall the DisplayPort connector module, reverse the removal procedure.
Front I/O assembly 76 Description Spare part number Front I/O assembly 745049-001 1. Prepare the computer for disassembly (Preparation for disassembly on page 42). 2. Remove the access panel (Access panel on page 43). 3. Remove the front bezel (Front bezel on page 44). 4. From the inside of the computer, disconnect the three front I/O cables from the following system board connectors: ● FRONT USB 3.0 (P24) ● FRONT USB (P23) ● FRONT AUD (P23) 5.
8. Pull the assembly away from the computer while threading the wires through the hole in the front of the chassis (3). To reinstall the assembly, reverse the removal procedure.
Power switch/LED assembly Description Spare part number Power switch/LED assembly 745050-001 1. Prepare the computer for disassembly (Preparation for disassembly on page 42). 2. Remove the access panel (Access panel on page 43). 3. Remove the front bezel (Front bezel on page 44). 4. Disconnect the cable from the system board connector labeled PB/LED. NOTE: System board appearance may vary. 5.
6. Rotate the assembly downward to remove it from the chassis (2). 7. Pull the assembly away from the chassis while threading the cable through the hole in front of the chassis.
Fan sink Description Spare part number Fan sink for use in 400 and 490 models, standard 745054-001 Fan sink for use in 490 models, BFR/PVC free 748826-001 WARNING! To reduce risk of personal injury from hot surfaces, allow the internal system components to cool before touching. NOTE: System board appearance may vary. 1. Prepare the computer for disassembly (Preparation for disassembly on page 42). 2. Remove the access panel (Access panel on page 43). 3.
4. Lift the fan sink from atop the processor. CAUTION: Fan sink retaining screws should be tightened in diagonally opposite pairs (as in an X) to evenly seat the heat sink on the processor. This is especially important as the pins on the socket are very fragile and any damage to them may require replacing the system board.
Processor Description Spare part number Intel Core i7 processor 4771 (3.5-GHz, 8-MB L3 cache), 84W 742563-001 4770 (3.4-GHz, 8-MB L3 cache), 84W 727373-001 4770s (3.1-GHz, 8-MB L3 cache), 65W 732507-001 Intel Core i5 processors 4670 (3.4-GHz, 6-MB L3 cache), 84W 727381-001 4670s (3.1-GHz, 6-MB L3 cache), 65W 732506-001 4570 (3.2-GHz, 6-MB L3 cache), 84W 727380-001 4570s (2.9-GHz, 6-MB L3 cache), 65W 732505-001 4430 (3.0-GHz, 6-MB L3 cache), 84W 745033-001 4430s (2.
6. Carefully lift the processor from the socket (3). CAUTION: Do NOT handle the pins in the processor socket. These pins are very fragile and handling them could cause irreparable damage. Once pins are damaged it may be necessary to replace the system board. NOTE: After installing a new processor onto the system board, always update the system ROM to ensure that the latest version of the BIOS is being used on the computer. The latest system BIOS can be found on the Web at: http://www8.hp.
Speaker Description Spare part number Speaker 745053-001 NOTE: System board appearance may vary. 84 1. Prepare the computer for disassembly (Preparation for disassembly on page 42). 2. Remove the access panel (Access panel on page 43). 3. Disconnect the speaker cable from the system board connector labeled SPKR. 4. Remove the speaker cable from the cable tie on the base pan.
5. From the outside front of the chassis, remove the Torx T15 screw that secures the speaker to the front of the chassis. 6. From the inside of the chassis, slide the speaker toward the right to remove it from its holder, and then remove it from the chassis. To replace the speaker, reverse the removal procedures.
Fan Description Spare part number Fan 745052-001 Fan, BFR/PVC free 748825-001 NOTE: System board appearance may vary. 1. Prepare the computer for disassembly (Preparation for disassembly on page 42). 2. Remove the access panel (Access panel on page 43). 3. From the outside, rear side of the chassis, remove the two Torx T15 screws that secure the fan to the chassis. 4. From the inside of the chassis, disconnect the fan control cable (1) from the system board connector labeled CHFAN2. 5.
Power supply NOTE: System board appearance may vary. Description Spare part number Power supply, 300W, Energy Star 5.0 712298-001 Power supply, 300W, Energy Star 6.0 748824-001 Power supply, 300W, Active PFC 715184-001 Power supply, 300W, active PFC, SEPA 752628-001 Power supply, 300W, regular 715185-001 NOTE: System board appearance may vary. 1. Prepare the computer for disassembly (Preparation for disassembly on page 42). 2. Remove the access panel (Access panel on page 43). 3.
5. 88 ● P4 connector: secondary hard drive ● P6 connector: secondary optical drive From the outside rear of the chassis, remove the four silver Torx T15 screws that connect the power supply to the chassis.
6. From the inside of the chassis, slide the power supply toward the front of the computer, rotate slightly into the computer so the power supply clears the lip on the top of the chassis, and then lift the power supply out of the chassis. To install the power supply, reverse the removal procedure.
System board NOTE: All system board spare part kits include replacement thermal material.
6. Slide the system board toward the front of the computer to disengage the I/O panel, and then lift the back (I/O side) of the board up at angle, and then lift system board out of the computer. NOTE: System board appearance may vary. When reinstalling the system board, first insert the I/O panel back into the slots in the rear of the chassis, and then align the board with the chassis screw holes. NOTE: When replacing the system board, you must change the chassis serial number in the BIOS.
6 Removal and replacement procedures: Small Form Factor Adherence to the procedures and precautions described in this chapter is essential for proper service. After completing all necessary removal and replacement procedures, run the Diagnostics utility to verify that all components operate properly. NOTE: Not all features listed in this guide are available on all computers.
Access panel Description Spare part number Access panel 745042-001 1. Prepare the computer for disassembly (Preparation for disassembly on page 92). 2. Loosen the thumbscrew on the rear of the computer (1) then slide the panel back (2) and lift if off the computer (3). To install the access panel, reverse the removal procedure.
Front bezel Description Spare part number Front bezel 745039-001 1. Prepare the computer for disassembly (Preparation for disassembly on page 92). 2. Remove the access panel (Access panel on page 93). 3. Lift up the three tabs on the side of the bezel (1), then rotate the bezel off the chassis (2). To install the front bezel, reverse the removal procedure.
Front bezel security The front bezel can be locked in place by installing a security screw provided by HP. To install the security screw: 1. Prepare the computer for disassembly (Preparation for disassembly on page 92). 2. Remove the access panel (Access panel on page 93). 3. Remove one of the five silver 6-32 standard screws located on top of the drive cage. 4. Install the security screw through the middle front bezel release tab to secure the front bezel in place.
Bezel blanks Description Spare part number Optical drive bezel blank 732769-001 On some models, there are bezel blanks covering the 3.5-inch and 5.25-inch external drive bays that need to be removed before installing a drive. To remove a bezel blank: 1. Remove the access panel (Access panel on page 93). 2. Remove the front bezel (Front bezel on page 94). 3. To remove a slim optical drive bezel blank, press inward on the five retaining tabs (1) and pull the blank off the front bezel (2).
Memory Description Spare part number 8-GB, PC3-12800 689375-001 4-GB, PC3-12800 671613-001 2-GB, PC3-12800 671612-001 The computer comes with double data rate 3 synchronous dynamic random access memory (DDR3SDRAM) dual inline memory modules (DIMMs). DIMMs The memory sockets on the system board can be populated with up to two industry-standard DIMMs. These memory sockets are populated with at least one preinstalled DIMM.
Populating DIMM sockets There are two DIMM sockets on the system board, with one socket per channel. The sockets are labeled DIMM1 and DIMM3. Socket DIMM1 operates in memory channel B. Socket DIMM3 operates in memory channel A. The system will automatically operate in single channel mode, dual channel mode, or flex mode, depending on how the DIMMs are installed. NOTE: Single channel and unbalanced dual channel memory configurations will result in inferior graphics performance.
4. Open both latches of the memory module socket (1), and insert the memory module into the socket (2). NOTE: A memory module can be installed in only one way. Match the notch on the module with the tab on the memory socket. For maximum performance, populate the sockets so that the memory capacity is spread as equally as possible between Channel A and Channel B. 5. Push the module down into the socket, ensuring that the module is fully inserted and properly seated.
Expansion card Description Spare part number Nvidia NVS310 PCIe x16 graphics card, 512 MB 707252-001 Nvidia NVS315 PCIe x16 graphics card, 1 GB 720837-001 AMD Radeon HD8490 DP PCIe x16 graphics card, 1 GB 717219-001 AMD Radeon HD8350 DH PCIe x16 graphics card, 1 GB DDR3 717220-001 Intel Dual Band Wireless-N 7260 802.
5. Before installing an expansion card, remove the expansion slot cover or the existing expansion card. NOTE: Before removing an installed expansion card, disconnect any cables that may be attached to the expansion card. a. If you are installing an expansion card in a vacant socket, remove the appropriate expansion slot cover on the back of the chassis. Pull the slot cover straight up then away from the inside of the chassis. b.
c. If you are removing a PCI Express x16 card, pull the retention arm on the back of the expansion socket away from the card and carefully rock the card back and forth until the connectors pull free from the socket. Pull the expansion card straight up from the socket then away from the inside of the chassis to release it from the chassis frame. Be sure not to scrape the card against the other components. 6. Store the removed card in anti-static packaging. 7.
8. To install a new expansion card, hold the card just above the expansion socket on the system board then move the card toward the rear of the chassis (1) so that the bracket on the card is aligned with the open slot on the rear of the chassis. Press the card straight down into the expansion socket on the system board (2). NOTE: When installing an expansion card, press firmly on the card so that the whole connector seats properly in the expansion card slot. 9.
System board connections Refer to the following illustration and table to identify the system board connectors for your model. 104 No.
Drives Description Spare part number Optical drives DVD±RW drive 657958-001 DVD-ROM drive 608394-001 Blu-ray BD-RW SuperMulti XL Drive 719157-001 Hard drives 2 TB, 7200 rpm hard drive, 3.5 inch 747993-001 1 TB hard drive, hybrid SSD 724937-001 1 TB, 7200 rpm hard drive, 3.5 inch 747992-001 500 GB, 7200 rpm hard drive, 3.
branch is a dual-headed cable with the first connector routed to the 3.5-inch hard drive bay and the second connector routed to the 2.5-inch hard drive bay. ● You must install guide screws to ensure the drive will line up correctly in the drive cage and lock in place. HP has provided four extra 6-32 standard guide screws installed on the top of the drive bay. The 6-32 standard guide screws are required for a media card reader or a secondary hard drive installed in the 3.5-inch optional drive bay.
Drive positions 1 Slim optical drive bay 2 3.5-inch internal hard drive bay 3 3.5-inch drive bay for optional drives (media card reader shown) 4 2.5-inch internal hard drive bay NOTE: The drive configuration on your computer may be different than the drive configuration shown above. To verify the type and size of the storage devices installed in the computer, run Computer Setup.
Removing a 3.5-inch device CAUTION: All removable media should be taken out of a drive before removing the drive from the computer. 108 1. Prepare the computer for disassembly (Preparation for disassembly on page 92). 2. Remove the access panel (Access panel on page 93). 3. Remove the front bezel (Front bezel on page 94). 4. Rotate the drive cage to its upright position. 5.
6. Press inward on the release lever at the rear of the device (1) and slide the device out of the rear of the drive bay (2). Installing a 3.5-inch device 1. Prepare the computer for disassembly (Preparation for disassembly on page 92). 2. Remove the access panel (Access panel on page 93). 3. Remove the front bezel (Front bezel on page 94). If you are installing a drive in a bay covered by a bezel blank, remove the bezel blank. See Bezel blanks on page 96 for more information. 4.
110 5. Rotate the drive cage to its upright position. 6. Slide the device into the drive bay, making sure to align the guide screws with the guide slots, until the device snaps into place.
7. If installing a USB 3.0 media card reader, you must use the USB 3.0 to USB 2.0 adapter and connect the adapter cable from the media card reader to the USB 2.0 connector on the system board labeled MEDIA. NOTE: Refer to System board connections on page 104 for an illustration of the system board drive connectors. 8. Rotate the drive cage back down to its normal position. CAUTION: Be careful not to pinch any cables or wires when rotating the drive cage down.
Removing a slim optical drive CAUTION: All removable media should be taken out of a drive before removing the drive from the computer. 1. Prepare the computer for disassembly (Preparation for disassembly on page 92). 2. Remove the access panel (Access panel on page 93). 3.
Installing a slim optical drive 1. Prepare the computer for disassembly (Preparation for disassembly on page 92). 2. If the computer is on a stand, remove the computer from the stand. 3. Remove the access panel (Access panel on page 93). 4. Remove the front bezel (Front bezel on page 94) if you are installing a drive in a bay covered by a bezel blank, then remove the bezel blank. See Bezel blanks on page 96 for more information. 5.
6. Slide the optical drive through the front bezel all the way into the bay so that it locks in place (1), then connect the power and data cables to the rear of the drive (2). 7. Connect the opposite end of the data cable to the white SATA connector on the system board labeled SATA5. NOTE: Refer to System board connections on page 104 for an illustration of the system board drive connectors. 8. Replace the front bezel if it was removed.
5. Pull the release lever next to the rear of the hard drive outward (1). While pulling the release lever out, slide the drive back until it stops, then lift the drive up and out of the bay (2). 6. To install a hard drive, you must transfer the silver and blue isolation mounting guide screws from the old hard drive to the new hard drive.
7. Align the guide screws with the slots on the chassis drive cage, press the hard drive down into the bay, then slide it forward until it stops and locks in place. 8. Connect the power cable and data cable to the back of the hard drive. NOTE: The data cable for the primary hard drive must be connected to the dark blue connector labeled SATA0 on the system board to avoid any hard drive performance problems. 9. Replace the access panel. 10. If the computer was on a stand, replace the stand. 11.
Removing a 2.5-inch hard drive 1. Prepare the computer for disassembly (Preparation for disassembly on page 92). 2. Remove the access panel (Access panel on page 93). 3. Rotate the drive cage to its upright position. 4. Disconnect the power cable and data cable from the back of the hard drive. 5. Pull outward on the release lever at the rear of the drive (1) then slide the drive back until it stops and pull it down and out of the drive bay (2). Installing a 2.5-inch hard drive 1.
4. Install four black and blue M3 isolation mounting guide screws (two on each side of the drive). NOTE: M3 metric isolation mounting guide screws can be purchased from HP. When replacing a drive, transfer the four M3 isolation mounting guide screws from the old drive to the new one. 5. Rotate the drive cage to its upright position. 6. Align the guide screws on the drive with the J-slots on the sides of the drive bay. Press the drive up into the drive bay then slide it forward until it locks in place.
Power supply Description Spare part number Power supply, 240W, 85% efficient 722536-001 Power supply, 240W, standard 702457-001 WARNING! To reduce potential safety issues, only the power supply provided with the computer, a replacement power supply provided by HP, or a power supply purchased as an accessory from HP should be used with the computer. The power supply is located at the rear of the chassis.
6. From the outside, rear of the computer, remove the three Torx screws that secure the power supply to the rear of the chassis. 7. From the inside of the chassis, press the release button at the front of the power supply (1). 8. Slide the power supply forward (2), and then lift it out of the chassis (3). To install the power supply, reverse the removal procedure. CAUTION: When installing the power supply cables, make sure they are properly positioned in the clip under the drive cage.
Fan duct Description Spare part number Fan duct 727145-001 The fan duct sits between the front fan and the heat sink. 1. Prepare the computer for disassembly (Preparation for disassembly on page 92). 2. Remove the access panel (Access panel on page 93). 3. Rotate the fan duct upward. 4. Pull the duct away from the chassis to disengage the clips on the duct from the chassis. To install the fan duct, insert the clips on the edge of the fan onto the metal posts on the chassis.
Front I/O assembly 122 Description Spare part number Front I/O assembly 745037-001 1. Prepare the computer for disassembly (Preparation for disassembly on page 92). 2. Remove the access panel (Access panel on page 93). 3. Remove the front bezel (Front bezel on page 94). 4. Rotate the drive cage to its upright position. 5. Cut the plastic tie that secures the longer cable to the power supply. 6.
7. Remove the cables from the cable clips under the drive cage. 8. Remove the Torx T15 screw (1) that secures the assembly to the front of the chassis.
9. Press the tab on the right side of the assembly (2) to disengage it from the chassis. 10. Push the assembly into the chassis, and then remove it from the chassis. To install the assembly, insert the assembly from the inside of the chassis, and then pull the tab on the left side of the assembly out the front of the chassis. Push the right side until it clicks into place. NOTE: Be sure to correctly route the cables beneath the drive cage when reinstalling the assembly.
Power switch assembly Description Spare part number Power switch assembly 745038-001 1. Prepare the computer for disassembly (Preparation for disassembly on page 92). 2. Remove the access panel (Access panel on page 93). 3. Remove the front bezel (Front bezel on page 94). 4. Rotate the drive cage to its upright position. 5. Disconnect the cable from the system board connector labeled PB/LED.
126 6. Remove the cable from the cable clips under the drive cage. 7. From the inside of the chassis, press down on the tab on the top of the power switch to disengage the power switch from the chassis.
8. Pull the power switch out the front of the chassis, while routing the cable through the hole in the chassis. To install the power switch assembly, first insert the cable through the hole from the front of the chassis. After inserting the cable, place the bottom of the assembly into the slot, and then rotate the top up until it snaps into place. NOTE: Be sure to correctly route the cables beneath the drive cage when reinstalling the assembly.
Speaker Description Spare part number Speaker 727149-001 The speaker is attached to the front of the chassis under the rotating drive cage. 128 1. Prepare the computer for disassembly (Preparation for disassembly on page 92). 2. Remove the access panel (Access panel on page 93). 3. Remove the front bezel (Front bezel on page 94). 4. Rotate the drive cage to its upright position. 5.
6. From the outside, front of the chassis, remove the two Torx screws that secure the speaker to the chassis. 7. Lift the speaker from the inside of the chassis to remove it. To install the speaker, reverse the removal procedures.
Fan sink Description Spare part number Fan sink 745661-001 The fan sink is secured atop the processor with four captive Torx screws. The fan sink includes a heat sink and a fan. 1. Prepare the computer for disassembly (Preparation for disassembly on page 92). 2. Remove the access panel (Access panel on page 93). 3. Remove the fan duct (Fan duct on page 121). 4. Loosen the four captive Torx T15 screws that secure the fan sink to the system board tray.
5. Disconnect the fan cable from the system board connector labeled CPUFAN (1), and then lift the heat sink from atop the processor (2). When reinstalling the fan sink, make sure that its bottom has been cleaned with an alcohol wipe and fresh thermal grease has been applied to the top of the processor. CAUTION: Fan sink retaining screws should be tightened in diagonally opposite pairs (as in an X) to evenly seat the fan sink on the processor to avoid damage that could require replacing the system board.
Processor Description Spare part number Intel Core i7 processors 4771 (3.5-GHz, 8-MB L3 cache), 84W 742563-001 4770 (3.4-GHz, 8-MB L3 cache), 84W 727373-001 4770s (3.1-GHz, 8-MB L3 cache), 65W 732507-001 Intel Core i5 processors 4670 (3.4-GHz, 6-MB L3 cache), 84W 727381-001 4670s (3.1-GHz, 6-MB L3 cache), 65W 732506-001 4570 (3.2-GHz, 6-MB L3 cache), 84W 727380-001 4570s (2.9-GHz, 6-MB L3 cache), 65W 732505-001 4430 (3.0-GHz, 6-MB L3 cache), 84W 745033-001 4430s (2.
7. Carefully lift the processor from the socket (3). CAUTION: Do NOT handle the pins in the processor socket. These pins are very fragile and handling them could cause irreparable damage. Once pins are damaged it may be necessary to replace the system board. The heat sink must be installed within 24 hours of installing the processor to prevent damage to the processor’s solder connections.
System board 134 Description Spare part number System board for use in models without Windows 8 (includes thermal material) 718414-001 System board for use in models with Windows 8 Standard (includes thermal material) 718414-501 System board for use in models with Windows 8 Professional (includes thermal material) 718414-601 System board for use only in models in the People’s Republic of China with NetClone (includes thermal material) 745239-001 1.
8. Slide the system board toward the front of the chassis to disengage the connectors. 9. Lift the system board up and out of the chassis. To install the system board, reverse the removal procedure. NOTE: When replacing the system board, you must also change the chassis serial number in the BIOS. CAUTION: When reconnecting the cables it is important that they be positioned correctly.
Changing from desktop to tower configuration The Small Form Factor computer can be used in a tower orientation with an optional tower stand that can be purchased from HP. 1. Prepare the computer for disassembly (Preparation for disassembly on page 92). 2. Orient the computer so that its right side is facing down and place the computer in the optional stand. NOTE: To stabilize the computer in a tower orientation, HP recommends the use of the optional tower stand. 3.
7 Computer Setup (F10) Utility Computer Setup (F10) Utilities Use Computer Setup (F10) Utility to do the following: ● Change factory default settings. ● Set the system date and time. ● Set, view, change, or verify the system configuration, including settings for processor, graphics, memory, audio, storage, communications, and input devices. ● Modify the boot order of bootable devices such as hard drives, optical drives, or USB flash media devices.
● Enable or disable removable media boot ability. ● Solve system configuration errors detected but not automatically fixed during the Power-On SelfTest (POST). ● Replicate the system setup by saving system configuration information on a USB device and restoring it on one or more computers. ● Execute self-tests on a specified ATA hard drive (when supported by drive). ● Enable or disable DriveLock security (when supported by drive).
Computer Setup—File NOTE: Support for specific Computer Setup options may vary depending on the hardware configuration.
Computer Setup—Storage NOTE: Support for specific Computer Setup options may vary depending on the hardware configuration. Table 7-2 Computer Setup—Storage Option Description Device Configuration Lists all installed BIOS-controlled storage devices. When a device is selected, detailed information and options are displayed. The following options may be presented: ● Hard Disk: Size, model, firmware version, serial number, connector color, SMART category.
Table 7-2 Computer Setup—Storage (continued) Removable Media Boot Enables/disables ability to boot the system from removable media. Default is enabled. Boot Order Allows you to: ● UEFI Boot Sources: Specify the order in which EFI boot sources (such as a internal hard drive, USB hard drive, USB optical drive, or internal optical drive) are checked for a bootable operating system image.
Computer Setup—Security NOTE: Support for specific Computer Setup options may vary depending on the hardware configuration. Table 7-3 Computer Setup—Security Option Description Setup Password Allows you to set and enable a setup (administrator) password. NOTE: If the setup password is set, it is required to change Computer Setup options, flash the ROM, and make changes to certain plug and play settings under Windows. Power-On Password Allows you to set and enable a power-on password.
Table 7-3 Computer Setup—Security (continued) Device Security Allows you to set Device Available/Device Hidden (default is Device Available) for: ● Embedded security device ● System audio ● USB controller (varies by model) ● Network controller NOTE: USB Security You must disable AMT before trying to hide the network controller.
Table 7-3 Computer Setup—Security (continued) Master Boot Record Security Enables/disables Master Boot Record (MBR) security. The MBR contains information needed to successfully boot from a disk and to access the data stored on the disk. Master Boot Record Security may prevent unintentional or malicious changes to the MBR, such as those caused by some viruses or by the incorrect use of certain disk utilities.
Table 7-3 Computer Setup—Security (continued) System Security (these options are hardware dependent) NOTE: Available options are displayed depending on system configuration. Data Execution Prevention (enable/disable) - Helps prevent operating system security breaches. Default is enabled. SVM CPU Virtualization (enable/disable). Controls the virtualization features of the processor. Changing this setting requires turning the computer off and then back on. Default is disabled.
Table 7-3 Computer Setup—Security (continued) System Security (continued) OS management of Embedded Security Device (enable/disable) - This option allows the user to limit OS control of the Embedded Security Device. Default is enabled. This option is automatically disabled if Trusted Execution Technology is enabled.
Computer Setup—Power NOTE: Support for specific Computer Setup options may vary depending on the hardware configuration. Table 7-4 Computer Setup—Power Option Description OS Power Management ● Idle Power Savings—Extended/Normal. Allows certain operating systems to decrease the processors power consumption when the processor is idle. Default is extended. ● Runtime Power Management— Enable/Disable.
Computer Setup—Advanced NOTE: Support for specific Computer Setup options may vary depending on the hardware configuration. Table 7-5 Computer Setup—Advanced (for advanced users) Option Heading Power-On Options Allows you to set: ● POST mode (QuickBoot, Clear Memory, FullBoot, or FullBoot Every x Days). ◦ QuickBoot (default) = Do not clear memory or perform a memory test. ◦ FullBoot = Memory test (count) on cold boot. Clears memory on all boots. ◦ Clear Memory = No memory count on cold boot.
Table 7-5 Computer Setup—Advanced (for advanced users) (continued) BIOS Power-On Allows you to set the computer to turn on automatically at a time you specify. Onboard Devices Allows you to set resources for or disable Legacy devices. Select the Legacy device's IRQ, DMA, and I/O Range. The settings may not take effect for all operating systems. To hide a device from the operating system, see Security > Device Security.
Table 7-5 Computer Setup—Advanced (for advanced users) (continued) Option ROM Launch Policy AMT Configuration Let you set the launch policy for option ROMs. An Option ROM typically consists of firmware that is called by the system BIOS. For example, an adapter card that controls a boot device might contain firmware that is used to connect the device to the system once the Option ROM is loaded.
8 Troubleshooting without diagnostics This chapter provides information on how to identify and correct minor problems, such as USB devices, hard drive, optical drive, graphics, audio, memory, and software problems. If you encounter problems with the computer, refer to the tables in this chapter for probable causes and recommended solutions.
● If you recently installed new software, uninstall the software and see if the computer functions properly. ● Boot the computer to the Safe Mode to see if it will boot without all of the drivers loaded. When booting the operating system, use “Last Known Configuration.” ● Refer to the comprehensive online technical support at http://www.hp.com/support. ● Refer to Helpful hints on page 152 in this guide.
● Check the Power LED on the front of the computer to see if it is flashing red. The flashing lights are error codes that will help you diagnose the problem. Refer to Appendix A, POST error messages on page 190 for more information. ● Turn up the brightness and contrast controls of the monitor if the monitor is dim. ● Press and hold any key. If the system beeps, then the keyboard should be operating correctly. ● Check all cable connections for loose connections or incorrect connections.
Solving general problems You may be able to easily resolve the general problems described in this section. If a problem persists and you are unable to resolve it yourself or if you feel uncomfortable about performing the operation, contact an authorized dealer or reseller. WARNING! When the computer is plugged into an AC power source, voltage is always applied to the system board.
Cursor will not move using the arrow keys on the keypad. Cause Solution The Num Lock key is turned on. Press the Num Lock key. The Num Lock light must be off if you want to use the arrow keys on the keypad. You can also disable or enable the Num Lock key in Computer Setup at Advanced > Device Options. There is no sound or sound volume is too low. Cause Solution System volume may be set low or muted. 1.
Poor performance. Cause Solution Hard drive fragmented. Defragment hard drive. Program previously accessed did not release reserved memory back to the system. Restart the computer. Virus resident on the hard drive. Run virus protection program. Too many applications running. Windows 7: 1. Close unnecessary applications to free up memory. 2. Add more memory. 3. Some applications run in the background and can be closed by right-clicking on their corresponding icons in the task tray.
Computer powered off automatically and the Power LED flashes Red two times, once every second, followed by a two second pause, and the computer beeps two times. (Beeps stop after fifth iteration but LEDs continue flashing). Cause Solution Processor thermal protection activated: 1. Ensure that the computer air vents are not blocked and the processor cooling fan is running. 2. Open the access panel, press the power button, and see if the processor fan (or other system fan) spins.
Solving power problems Common causes and solutions for power problems are listed in the following table. Power supply shuts down intermittently. Cause Solution If equipped with a voltage selector, voltage selector switch on rear of computer chassis (some models) not switched to correct line voltage (115V or 230V). Select the proper AC voltage using the selector switch. Power supply will not turn on because of internal power supply fault. Replace the power supply.
Power LED flashes Red four times, once every second, followed by a two second pause, and the computer beeps four times. (Beeps stop after fifth iteration but LEDs continue flashing.) Cause Solution Power failure (power supply is overloaded). 1. If equipped with a voltage selector, check that the voltage selector, located on the rear of the power supply (some models), is set to the appropriate voltage. Proper voltage setting depends on your region. 2.
Disk transaction problem. Cause Solution Either the directory structure is bad or there is a problem with a file. In Windows 7, click Start, expand Computer, and rightclick on a drive. Select Properties, and then select the Tools tab. Under Error-checking click Check Now. In Windows 8, on the Start screen type e, and then click File Explorer from the list of applications. In the left column, expand Computer, right-click on a drive, select Properties, and then select the Tools tab.
Nonsystem disk/NTLDR missing message. Cause Solution Bootable hard drive is not attached as first in a multi-hard drive configuration. If attempting to boot from a hard drive, ensure it is attached to the system board dark blue SATA connector. Bootable hard drive is not listed first in the Boot Order. Run the Computer Setup utility and select Storage > Boot Order and ensure the bootable hard drive is listed immediately under the Hard Drive entry. Computer will not boot from hard drive.
Solving media card reader problems Media card will not work in a digital camera after formatting it in Windows. Cause Solution By default, Windows will format any media card with a capacity greater than 32MB with the FAT32 format. Some digital cameras use the FAT (FAT16 & FAT12) format and can not operate with a FAT32 formatted card. Either format the media card in the digital camera or select FAT file system to format the media card in a computer with Windows.
Do not know how to remove a media card correctly. Cause Solution The computer’s software is used to safely eject the card. In Windows 7, click Start, select Computer, right-click on the corresponding drive icon, and then select Eject. Pull the card out of the slot. In Windows 8, on the Start screen, type e, and then click File Explorer from the list of applications. Expand Computer, right-click on the corresponding drive icon, and then select Eject. Pull the card out of the slot.
Solving display problems If you encounter display problems, see the documentation that came with the monitor and to the common causes and solutions listed in the following table. Blank screen (no video). Cause Solution Monitor is not turned on and the monitor light is not on. Turn on the monitor and check that the monitor light is on. Bad monitor. Try a different monitor. The cable connections are not correct. Check the cable connection from the monitor to the computer and to the electrical outlet.
Blank screen and the power LED flashes Red five times, once every second, followed by a two second pause, and the computer beeps five times. (Beeps stop after fifth iteration but LEDs continue flashing.) Cause Solution Pre-video memory error. 1. Reseat DIMMs. Power on the system. 2. Replace DIMMs one at a time to isolate the faulty module. 3. Replace third-party memory with HP memory. 4. Replace the system board.
Dim characters. Cause Solution The brightness and contrast controls are not set properly. Adjust the monitor brightness and contrast controls. Cables are not properly connected. Check that the graphics cable is securely connected to the graphics card (if applicable) or video connector and the monitor. Blurry video or requested resolution cannot be set. Cause Solution If the graphics controller was upgraded, the correct graphics drivers may not be loaded.
“No Connection, Check Signal Cable” displays on screen. Cause Solution Monitor video cable is disconnected. Connect the video cable between the monitor and computer. CAUTION: Ensure that the computer power is off while connecting the video cable. “Out of Range” displays on screen. Cause Solution Video resolution and refresh rate are set higher than what the monitor supports. Restart the computer and enter Safe Mode.
High pitched noise coming from inside a flat panel monitor. Cause Solution Brightness and/or contrast settings are too high. Lower brightness and/or contrast settings. Fuzzy focus; streaking, ghosting, or shadowing effects; horizontal scrolling lines; faint vertical bars; or unable to center the picture on the screen (flat panel monitors using an analog VGA input connection only).
Solving audio problems If the computer has audio features and you encounter audio problems, see the common causes and solutions listed in the following table. Sound cuts in and out. Cause Solution Processor resources are being used by other open applications. Shut down all open processor-intensive applications. Sound does not come out of the speaker or headphones. Cause Solution Software volume control is turned down or muted.
Sound does not come out of the speaker or headphones. Cause Solution The application is set to use a different audio device than speakers. Some graphics cards support audio over the DisplayPort connection (if applicable), so multiple audio devices may be listed in Device Manager. Make sure the correct device is being used. To access Device Manager in Windows 7, click Start, select Control Panel, and then select Device Manager.
There is no sound or sound volume is too low. Cause Solution The application is set to use a different audio device than speakers. Some graphics cards support audio over the DisplayPort connection (if applicable), so multiple audio devices may be listed in Device Manager. Make sure the correct device is being used. To access Device Manager in Windows 7, click Start, select Control Panel, and then select Device Manager.
Printer will not turn on. Cause Solution The cables may not be connected properly. Reconnect all cables and check the power cord and electrical outlet. Printer prints garbled information. Cause Solution The correct printer driver for the application is not installed. Install the correct printer driver for the application. The cables may not be connected properly. Reconnect all cables. Printer memory may be overloaded. Reset the printer by turning it off for one minute, then turn it back on.
Keyboard commands and typing are not recognized by the computer. Cause Solution Keyboard needs repairs. See the Worldwide Limited Warranty for terms and conditions. Computer is in Sleep state. Press the power button to resume from Sleep state. CAUTION: When attempting to resume from Sleep date, do not hold down the power button for more than four seconds. Otherwise, the computer will shut down and you will lose any unsaved data. Cursor will not move using the arrow keys on the keypad.
Mouse does not respond to movement or is too slow. Cause Solution Mouse may need cleaning. Remove the roller ball cover on the mouse and clean the internal components. Mouse may need repair. See the Worldwide Limited Warranty for terms and conditions. Computer is in Sleep state. Press the power button to resume from Sleep state. CAUTION: When attempting to resume from Sleep state, do not hold down the power button for more than four seconds.
Table 8-1 Solving Hardware Installation Problems (continued) A new device is not recognized as part of the system. Cause Solution When the system advised you of changes to the configuration, you did not accept them. Reboot the computer and follow the instructions for accepting the changes. A plug and play board may not automatically configure when added if the default configuration conflicts with other devices.
Power LED flashes Red five times, once every second, followed by a two second pause, and the computer beeps five times. (Beeps stop after fifth iteration but LEDs continue flashing.) Cause Solution Memory is installed incorrectly or is bad. CAUTION: To avoid damage to the DIMMs or the system board, you must unplug the computer power cord before attempting to reseat, install, or remove a DIMM module. 1. Reseat DIMMs. Power on the system. 2. Replace DIMMs one at a time to isolate the faulty module.
Solving Network Problems Some common causes and solutions for network problems are listed in the following table. These guidelines do not discuss the process of debugging the network cabling. Table 8-2 Solving Network Problems Wake-on-LAN feature is not functioning. Cause Solution S5 Maximum Power Saving feature is enabled. Disable the S5 Maximum Power Saving option in Computer Setup. Select Power > Hardware Power Management > S5 Maximum Power Savings. S5 Wake on LAN is disabled (some models).
Network driver does not detect network controller. Cause Solution Network controller is disabled. 1. Run Computer Setup and enable network controller. 2. Enable the network controller in the operating system using Device Manager. To access Device Manager in Windows 7, click Start, select Control Panel, and then select Device Manager. To access Device Manager in Windows 8, from the Start screen, type c, select Control Panel from the list of applications, and then select Device Manager.
Diagnostics reports a failure. Cause Solution The cable is not securely connected. Ensure that the cable is securely attached to the network connector and that the other end of the cable is securely attached to the correct device. The cable is attached to the incorrect connector. Ensure that the cable is attached to the correct connector. There is a problem with the cable or a device at the other end of the cable. Ensure that the cable and device at the other end are operating correctly.
Network controller stops working without apparent cause. Cause Solution The files containing the network drivers are corrupted. Reinstall the network drivers using the Recovery Disc Set in Windows 7 or Windows recovery tools in Windows 8. If necessary, download the softpaq from the web (from a different computer). The cable is not securely connected. Ensure that the cable is securely attached to the network connector and that the other end of the cable is securely attached to the correct device.
NOTE: The memory count will be affected by configurations with the Management Engine (ME) enabled. The ME uses 8MB of system memory in single channel mode or 16MB of memory in dualchannel mode to download, decompress, and execute the ME firmware for Out-of-Band (OOB), thirdparty data storage, and other management functions. System will not boot or does not function properly after installing additional memory modules. Cause Solution A memory module is not installed in the DIMM1 or XMM1 socket.
Power LED flashes Red five times, once every second, followed by a two second pause, and the computer beeps five times. (Beeps stop after fifth iteration but LEDs continue flashing.) Cause Solution Memory is installed incorrectly or is bad. 1. Reseat DIMMs. Power on the system. 2. Replace DIMMs one at a time to isolate the faulty module. 3. Replace third-party memory with HP memory. 4. Replace the system board.
Solving CD-ROM and DVD problems If you encounter CD-ROM or DVD problems, see the common causes and solutions listed in the following table or to the documentation that came with the optional device. System will not boot from CD-ROM or DVD drive. Cause Solution The device is attached to a SATA port that has been hidden in the Computer Setup utility. Run the Computer Setup utility and ensure Device Available is selected for the device's SATA port in Security > Device Security.
Movie will not play in the DVD drive. Cause Solution Movie may be regionalized for a different country. See the documentation that came with the DVD drive. Decoder software is not installed. Install decoder software. Damaged media. Replace media. Movie rating locked out by parental lock. Use DVD software to remove parental lock. Media installed upside down. Reinstall media. Cannot eject compact disc (tray-load unit). Cause Solution Disc not properly seated in the drive.
Recording or copying CDs is difficult or impossible. Cause Solution Wrong or poor quality media type. 1. Try using a slower speed when recording. 2. Verify that you are using the correct media for the drive. 3. Try a different brand of media. Quality varies widely between manufacturers. Solving USB flash drive problems If you encounter USB flash drive problems, common causes and solutions are listed in the following table. USB flash drive is not seen as a drive letter in Windows.
Solving front panel component problems If you encounter problems with devices connected to the front panel, refer to the common causes and solutions listed in the following table. A USB device, headphone, or microphone is not recognized by the computer. Cause Solution Device is not properly connected. 1. Turn off the computer. 2. Reconnect the device to the front of the computer and restart the computer. The device does not have power.
Unable to connect to the Internet. Cause Solution The CAT5 UTP cable is disconnected. Connect the CAT5 UTP cable between the cable modem and the computers’s RJ-45 connector. (If the connection is good, the “PC” LED light on the front of the cable/DSL modem will be on.) IP address is not configured properly. Contact your ISP for the correct IP address. Cookies are corrupted. (A “cookie” is a small piece of information that a Web server can store temporarily with the Web browser.
Solving software problems Most software problems occur as a result of the following: ● The application was not installed or configured correctly. ● There is insufficient memory available to run the application. ● There is a conflict between applications. ● Be sure that all the needed device drivers have been installed. ● If you have installed an operating system other than the factory-installed operating system, check to be sure it is supported on the system.
Computer will not continue after HP logo screen displays. Cause Solution System files may be damaged. In Windows 7, use recovery media to scan hard drive for errors, or use Windows Startup Repair to fix problems that might prevent Windows from starting correctly. Windows Startup Repair is one of the recovery tools in the System Recovery Options menu. You can also create a system repair disc that contains the System Recovery Options menu.
9 POST error messages This appendix lists the error codes, error messages, and the various indicator light and audible sequences that you may encounter during Power-On Self-Test (POST) or computer restart, the probable source of the problem, and steps you can take to resolve the error condition. POST Message Disabled suppresses most system messages during POST, such as memory count and non-error text messages. If a POST error occurs, the screen will display the error message.
POST numeric codes and text messages This section covers those POST errors that have numeric codes associated with them. The section also includes some text messages that may be encountered during POST. NOTE: The computer will beep once after a POST text message is displayed on the screen. Control panel message Description Recommended action 101-Option ROM Checksum Error System ROM or expansion board option ROM checksum. 1. Verify the correct ROM. 2. Flash the ROM if needed. 3.
Control panel message Description Recommended action 163-Time & Date Not Set Invalid time or date in configuration memory. Reset the date and time under Control Panel (Computer Setup can also be used). If the problem persists, replace the RTC battery. See the Removal and Replacement section for instructions on installing a new battery, or contact an authorized dealer or reseller for RTC battery replacement. RTC (real-time clock) battery may need to be replaced.
Control panel message Description Recommended action 301-Keyboard Error Keyboard failure. 1. Reconnect keyboard with computer turned off. 2. Check connector for bent or missing pins. 3. Ensure that none of the keys are depressed. 4. Replace keyboard. 1. Reconnect keyboard with computer turned off. 2. Replace the system board. 1. Reconnect the keyboard with computer turned off. 2. Ensure that none of the keys are depressed. 3. Replace the keyboard. 4. Replace the system board. 1.
Control panel message Description Recommended action 514-CPU or Chassis Fan not Detected CPU or chassis fan is not connected or may have malfunctioned. 1. Reseat CPU or chassis fan. 2. Reseat fan cable. 3. Replace CPU or chassis fan. 1. Reseat power supply fan. 2. Reseat fan cable. 3. Replace power supply fan. 1. Check and/or replace cables. 2. Clear CMOS. (See Appendix B, Password security and resetting CMOS on page 203.) 3. Replace diskette drive. 4. Replace the system board. 1.
Control panel message Description Recommended action 1152-Serial Port B Address Conflict Detected Both external and internal serial ports are assigned to COM2. 1. Remove any serial port expansion cards. 2. Clear CMOS. (See Appendix B, Password security and resetting CMOS on page 203.) 3. Reconfigure card resources and/or run Computer Setup or Windows utilities. 1. Remove any serial port expansion cards. 2. Clear CMOS. (See Appendix B, Password security and resetting CMOS on page 203.) 3.
Control panel message Description Recommended action 2200-PMM Allocation Error during MEBx Download Memory error during POST execution of the Management Engine (ME) BIOS Extensions option ROM. 1. Reboot the computer. 2. Unplug the power cord, re-seat the memory modules, and reboot the computer. 3. If the memory configuration was recently changed, unplug the computer, restore the original memory configuration, and reboot the computer. 4. If the error persists, replace the system board. 1.
Control panel message Description Recommended action 2204-Inventory error during MEBx execution BIOS information passed to the MEBx resulted in a failure. 1. Reboot the computer. 2. If the error persists, update to the latest BIOS version. 3. If the error still persists, replace the system board. 1. Reboot the computer. 2. If the error persists, update to the latest BIOS version. 3. If the error still persists, replace the system board.
Control panel message Description Recommended action 2220-USB Key Provisioning file has mismatch version Provisioning file contained on the USB key is not a valid version for the current ME firmware. 1. Reboot the computer. 2. If the error persists and system BIOS has been recently updated, restore previous system BIOS version. Otherwise, update the ME firmware version. 3. If the error still persists, replace the system board.
Control panel message Description Recommended action Network Server Mode Active and No Keyboard Attached Keyboard failure while Network Server Mode enabled. 1. Reconnect keyboard with computer turned off. 2. Check connector for bent or missing pins. 3. Ensure that none of the keys are depressed. 4. Replace keyboard. Parity Check 2 Parity RAM failure. Run Computer Setup and Diagnostic utilities.
Activity Beeps Possible cause Recommended action Red Power LED flashes two times, once every second, followed by a two second pause. Beeps stop after fifth iteration but LEDs continue until problem is solved. 2 Processor thermal protection activated: 1. Ensure that the computer air vents are not blocked and the processor cooling fan is running. 2. Open hood, press power button, and see if the processor fan spins.
Activity Beeps Possible cause Recommended action Red Power LED flashes six times, once every second, followed by a two second pause. Beeps stop after fifth iteration but LEDs continue until problem is solved. 6 Pre-video graphics error. For systems with a graphics card: 1. Reseat the graphics card. 2. Replace the graphics card. 3. Replace the system board. For systems with integrated graphics, replace the system board.
Activity Beeps Possible cause Recommended action Red Power LED flashes eleven times, once every second, followed by a two second pause. Beeps stop after fifth iteration but LEDs continue until problem is solved. 11 The current processor does not support a feature previously enabled on this system. 1. System does not power on and LEDs are not flashing. None System unable to power on. Press and hold the power button for less than 4 seconds.
10 Password security and resetting CMOS This computer supports security password features, which can be established through the Computer Setup Utilities menu. This computer supports two security password features that are established through the Computer Setup Utilities menu: setup password and power-on password. When you establish only a setup password, any user can access all the information on the computer except Computer Setup.
Resetting the password jumper CAUTION: If you enable the stringent security feature in Computer Setup and you forget the setup password or the power-on password, the computer is inaccessible and can no longer be used. Enabling the stringent password disables the ability to reset the password by moving the jumper on the system board. If you lose or forget the password, the system board must be replaced. This scenario is not covered under warranty.
8. Plug in the computer and turn on power. Allow the operating system to start. This clears the current passwords and disables the password features. 9. To establish new passwords, repeat steps 1 through 4, replace the password jumper on pins 1 and 2, then repeat steps 6 through 8. Establish the new passwords in Computer Setup. Clearing and resetting the CMOS The computer’s configuration memory (CMOS) stores information about the computer’s configuration.
4. Locate, press, and hold the CMOS button in for five seconds. NOTE: Make sure you have disconnected the AC power cord from the wall outlet. The CMOS button will not clear CMOS if the power cord is connected. NOTE: For assistance locating the CMOS button and other system board components, see the Illustrated Parts & Service Map (IPSM). 5. Replace the computer cover or access panel. 6. Reconnect the external devices. 7. Plug in the computer and turn on power.
11 HP PC Hardware Diagnostics To help troubleshoot and diagnose failures, use the UEFI-based hardware diagnostic solution that HP includes on all products. This tool can even be used if the computer will not boot to the operating system. Why run HP PC Hardware Diagnostics The HP PC Hardware Diagnostic tools simplify the process of diagnosing hardware issues and expedite the support process when issues are found. The tools save time by pinpointing the component that needs to be replaced.
Downloading HP PC Hardware Diagnostics to a USB device 1. Go to http://www.hp.com. 2. Click the Support & Drivers link. 3. Select the Drivers & Software tab. 4. Enter the product name in the text box and click Search. 5. Select your specific computer model. 6. Select your operating system. 7. In the Diagnostic section, click the HP UEFI Support Environment link. This link provides additional information. - or Click the Download button and select Run.
12 System backup and recovery Backing up, restoring, and recovering in Windows 8.1 or Windows 8 Your computer includes tools provided by HP and Windows to help you safeguard your information and retrieve it if you ever need to. These tools will help you return your computer to a proper working state or even back to the original factory state, all with simple steps.
NOTE: Any information on the USB flash drive will be erased before the recovery media is created. 2. ● To create the Windows 8.1 recovery media, from the Start screen, type recovery drive, then click on Create a recovery drive. Follow the on-screen instructions to continue. ● To create the Windows 8 recovery media, from the Start screen, type recovery drive, and then click on Settings, then click on Create a recovery drive. Follow the on-screen instructions to continue.
6. Select Troubleshoot. 7. Select Reset. 8. Follow the on-screen instructions to continue. Recovery using the Windows recovery USB flash drive To recover your system using the recovery USB flash drive you previously created: NOTE: If you did not create a recovery USB flash drive or the one you created does not work, see Recovery using Windows operating system media (purchased separately) on page 211. 1. If possible, back up all personal files. 2.
After the repair is completed and the Windows desktop appears: 1. Remove the Windows operating system media, and then insert the Driver Recovery media. 2. Install the Hardware Enabling Drivers first, and then install Recommended Applications. Backing up, restoring, and recovering in Windows 7 Your computer includes tools provided by HP and Windows to help you safeguard your information and retrieve it if you ever need to.
There are two types of recovery media. To determine which steps to follow for your computer: 1. Click the Start button. 2. Click All Programs. ● If Security and Protection is listed, continue with the steps in Creating recovery media using HP Recovery Manager (select models only) on page 213. ● If Productivity and Tools is listed, continue with the steps in Creating recovery discs with HP Recovery Disc Creator (select models only) on page 214.
NOTE: Recovery Media Creation formats the USB flash drive, deleting any files on it. 1. Close all open programs. 2. Insert the USB flash drive into a USB port on the computer. 3. Click the Start button, click All Programs, click Security and Protection, click Recovery Manager, and then click Recovery Media Creation. 4. Click Create recovery media with a USB flash drive, and then click Next. 5. Select the USB flash drive from the list of media.
After the Windows 7 operating system DVD has been created, create the Driver Recovery DVD: 1. Select Start > All Programs > Productivity and Tools > HP Recovery Disc Creator. 2. Select Driver disk. 3. From the drop-down menu, select the drive for burning the recovery media. 4. Click the Create button to start the burning process. Label the disc after you create it, and store it in a secure place.
To start System Restore: 1. Close all open programs. 2. Click the Start button, right-click Computer, and then click Properties. 3. Click System protection, System Restore, click Next, and then follow the on-screen instructions. System Recovery WARNING! This procedure will delete all user information. To prevent loss of information, be sure to back up all user information so you can restore it after recovery.
4. When Windows has loaded, click the Start button, and then click All Programs. ● If Security and Protection is listed, continue with step 5. ● If Productivity and Tools is listed, follow the steps in System Recovery when Windows is not responding on page 217. 5. Click Security and Protection, click Recovery Manager, and then click Recovery Manager. If prompted, click Yes to allow the program to continue. 6. Under I need help immediately, click System Recovery. 7. Select Yes, and then click Next.
To perform a System Recovery using recovery media: 1. If you are using a set of DVDs, insert the first recovery disc into the DVD drive tray, and close the tray. If you are using a recovery USB flash drive, insert it into a USB port. 2. Click the Start button, and then click Shut Down. or If the computer is not responding, press and hold the power button for approximately 5 seconds or until the computer turns off. 3.
NOTE: This process takes several minutes. 1. If possible, back up all personal files. 2. Restart the computer, and then insert the Windows 7 operating system DVD into the optical drive before the Windows operating system loads. NOTE: If the computer does not boot to the DVD, restart the computer and press Esc as the computer is powering on to see the startup menu. Use the arrow keys to select the boot menu and press Enter. Use the arrow keys to select the location where the recovery DVD is inserted.
A Battery replacement The battery that comes with the computer provides power to the real-time clock. When replacing the battery, use a battery equivalent to the battery originally installed in the computer. The computer comes with a 3-volt lithium coin cell battery. WARNING! The computer contains an internal lithium manganese dioxide battery. There is a risk of fire and burns if the battery is not handled properly. To reduce the risk of personal injury: Do not attempt to recharge the battery.
6. Locate the battery and battery holder on the system board. NOTE: On some computer models, it may be necessary to remove an internal component to gain access to the battery. 7. Depending on the type of battery holder on the system board, complete the following instructions to replace the battery. Type 1 a. Lift the battery out of its holder. b. Slide the replacement battery into position, positive side up. The battery holder automatically secures the battery in the proper position. Type 2 a.
b. Insert the new battery and position the clip back into place. NOTE: After the battery has been replaced, use the following steps to complete this procedure. 8. Replace the access panel. 9. Plug in the computer and turn on power to the computer. 10. Reset the date and time, your passwords, and any special system setups using Computer Setup. 11. Lock any security devices that were disengaged when the access panel was removed.
B Power cord set requirements The power supplies on some computers have external power switches. The voltage select switch feature on the computer permits it to operate from any line voltage between 100-120 or 220-240 volts AC. Power supplies on those computers that do not have external power switches are equipped with internal switches that sense the incoming voltage and automatically switch to the proper voltage.
Country-specific requirements Additional requirements specific to a country are shown in parentheses and explained below. 224 Country Accrediting Agency Country Accrediting Agency Australia (1) EANSW Italy (1) IMQ Austria (1) OVE Japan (3) METI Belgium (1) CEBC Norway (1) NEMKO Canada (2) CSA Sweden (1) SEMKO Denmark (1) DEMKO Switzerland (1) SEV Finland (1) SETI United Kingdom (1) BSI France (1) UTE United States (2) UL Germany (1) VDE 1.
C Specifications Microtower specifications Chassis Height 14.05 in 357 mm Width 7.2 in 182.9 mm Depth 15.82 in 402 mm Approximate Weight 15.75 lb 7.15 kg Operating 50° to 95°F 10° to 35°C Nonoperating -22° to 140°F -30° to 60°C Temperature Range NOTE: Operating temperature is derated 1.0° C per 300 m (1000 ft) to 3000 m (10,000 ft) above sea level; no direct sustained sunlight. Maximum rate of change is 10° C/Hr.
Standard Efficiency 300W active PFC(230 VAC input only) High Efficiency 300W active PFC EStar 6 82/85/82% efficient at 20/50/100% load (230V) Rated Input Current 1 4A This system utilizes an active power factor corrected power supply. This allows the system to pass the CE mark requirements for use in the countries of the European Union. The active power factor corrected power supply also has the added benefit of not requiring an input voltage range select switch.
Standard Efficiency 240W active PFC High Efficiency 240W active PFC 82/85/82% efficient at 20/50/100% load (230V) Rated Input Current 1 4A This system utilizes an active power factor corrected power supply. This allows the system to pass the CE mark requirements for use in the countries of the European Union. The active power factor corrected power supply also has the added benefit of not requiring an input voltage range select switch.
Index A access panel locked 155 microtower removal 43 microtower spare part number 43 microtower, spare part number 14, 22 SFF removal and replacement 93 SFF spare part number 93 SFF, spare part number 24, 32 adapter, DisplayPort to DVI, spare part number 16, 20, 26, 30 adapter, DisplayPort to HDMI, spare part number 16, 20, 26, 29 adapter, DisplayPort to VGA, spare part number 16, 20, 26, 29 audible codes 199 audio problems 169 B backup and recovery, Windows 7 212 Backup and Restore, Windows 7 215 backups
F f11 recovery, Windows 8 210 f11 recovery, Windows 8.
disassembly preparation 42 DisplayPort connector module removal and replacement 74 fan removal and replacement 86 fan sink removal and replacement 80 fan sink, spare part number 17 fan, spare part number 17 front bezel, spare part number 14, 22 front I/O assembly, spare part number 16, 22 front USB panel removal and replacement 76 power supply removal and replacement 87 power supply, spare part number 14, 23 power switch assembly removal and replacement 78 power switch assembly, spare part number 16, 22 pre
recovery discs, using for restore 218 recovery media, creating 214 recovery media, creating Windows 7 212 recovery partition, Windows 8 210 recovery partition, Windows 8.1 210 recovery USB flash drive, steps for creating Windows 7 213 recovery using Windows 8 operating system media 211 recovery using Windows 8.
SFF removal and replacement 128 SFF spare part number 128 SFF, spare part number 27, 31 specifications computer 225, 226 memory 97 microtower memory 47 static electricity 34 system board microtower removal and replacement 90 microtower spare part number 90 microtower, spare part number 14, 21 SATA connectors 40 SFF removal and replacement 134 SFF spare part number 134 SFF, spare part number 24, 30, 32 system board connections 56, 57, 58, 104 System Recovery using Windows 7 recovery media 217 System Recovery
