Power User Guide
© Copyright 2006 Hewlett-Packard Development Company, L.P. Microsoft and Windows are U.S. registered trademarks of Microsoft Corporation. Bluetooth is a trademark owned by its proprietor and used by Hewlett-Packard company under license. The information contained herein is subject to change without notice. The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services.
Table of contents 1 Power control and light locations 2 Power sources Connecting the AC adapter .................................................................................................................. 4 3 Standby and hibernation Standby ................................................................................................................................................ 5 Hibernation .........................................................................................................
Interpreting charge indicators ........................................................... 25 Managing low-battery conditions ........................................................................................................ 26 Identifying low-battery conditions ....................................................................................... 26 Low-battery condition ........................................................................................ 26 Critical low-battery condition .......
1 Power control and light locations The following illustration and table identify and describe the power control and light locations. (1) Component Description Power lights* (2) On: The computer is on. Blinking: The computer is in standby. Blinking rapidly: An AC adapter with a higher power rating should be connected, Off: The computer is off or in hibernation. (2) ENWW Power button When the computer is ● Off, press to turn on the computer. ● On, press to enter hibernation.
Component Description ● In standby, briefly press to exit standby. ● In hibernation, briefly press to exit hibernation. If the computer has stopped responding and Microsoft® Windows® shutdown procedures cannot be used, press and hold the power button for at least 5 seconds to turn off the computer. (3) fn+f3 Initiates standby. (4) Battery light Amber: A battery is charging. Green: A battery is close to full charge capacity.
2 Power sources The computer can run on internal or external AC power. The following table indicates the best power sources for common tasks. NOTE Use only the included AC adapter or one approved for use with this computer..
Connecting the AC adapter WARNING! To reduce the risk of electric shock or damage to the equipment: Plug the power cord into an AC outlet that is easily accessible at all times. Disconnect power from the computer by unplugging the power cord from the AC outlet (not by unplugging the power cord from the computer). If provided with a 3-pin attachment plug on the power cord, plug the cord into a grounded (earthed) 3-pin outlet.
3 Standby and hibernation Standby and hibernation are energy-saving features that conserve power and reduce startup time. They can be initiated by you or by the system. Standby CAUTION To avoid a complete battery discharge, do not leave the computer in standby for extended periods. Connect the computer to an external power source. Standby reduces power to system components that are not in use. When standby is initiated, your work is stored in random access memory (RAM), and then the screen is cleared.
Hibernation CAUTION If the configuration of the computer is changed during hibernation, resuming from hibernation may not be possible. When the computer is in hibernation: Do not dock the computer to or undock the computer from an optional docking device. Do not add or remove memory modules. Do not insert or remove any hard drives or optical drives. Do not connect or disconnect external devices. Do not insert or remove external media cards.
Initiating standby, hibernation or shutdown The following sections explain when to initiate standby or hibernation and when to shut down the computer. NOTE You cannot initiate any type of networking communications or perform any computer functions while the computer is in standby or hibernation. When you leave your work When standby is initiated, your work is stored in random access memory (RAM), and then the screen is cleared. When the computer is in standby, it uses less power than when it is on.
When using wireless communication, or readable or writable media (select models only) CAUTION To prevent possible audio and video degradation, or loss of audio or video playback functionality, do not initiate standby or hibernation while reading or writing to a CD, a DVD, or an external media card. To prevent loss of information, do not initiate standby or hibernation while writing to a CD, a DVD, or an external media card.
4 Factory power settings This section explains the factory standby, hibernation, and shutdown procedures. Turning the computer or display on or off Task Procedure Result Turn on the computer. Press the power button. ● The power lights are turned on. NOTE If the power lights blink rapidly, an AC adapter with a higher power rating should be connected. Turn off the computer.* 1. Save your work and close all open applications. 2.
Using emergency shutdown procedures CAUTION Emergency shutdown procedures result in the loss of unsaved information. If the you are unable to shut down the computer using the standard shutdown procedure, try the following emergency procedures in the sequence provided: 10 1. Press ctrl+alt+delete. Then, select Shut Down > Turn Off. 2. Press and hold the power button for at least 5 seconds. 3. Disconnect the computer from external power and remove the battery.
Initiating or resuming from standby Task Procedure Result Initiate standby. ● With the computer on, press fn+f3. ● The power lights blink. ● Select Start > Turn Off Computer > Stand by.* ● The screen clears. ● The power lights blink. In Windows XP Professional, if Stand by is not displayed: Allow the system to initiate standby. a. Click the down arrow. b. Select Stand by from the list. c. Click OK. No action required.
Initiating or restoring from hibernation Hibernation cannot be initiated unless it is enabled. Hibernation is enabled at the factory. To verify that hibernation remains enabled, Select Start > Control Panel > Performance and Maintenance > Power Options > Hibernate tab. If hibernation is enabled, the Enable hibernation check box is selected. Task Procedure Result Initiate hibernation. ● Press the power button. ● The power lights are turned off. – or – ● The screen clears.
5 Power options You can change many factory power settings in Windows Control Panel. For example, you can set an audio alert to warn you when the battery reaches a low-power condition, or you can change the factory settings for the power button. When the computer is on: ● Pressing fn+f3, called the "sleep button" by the operating system, initiates standby. ● The display switch turns off the display and initiates standby. The display switch is activated by closing the display.
Displaying the Power Meter icon The Power Meter icon is set at the factory to display in the notification area, at the far right of the taskbar. The icon changes shape to indicate whether the computer is running on battery or external power. To remove the Power Meter icon from the notification area: 1. Right-click the Power Meter icon in the notification area, and then click Adjust Power Properties. 2. Click the Advanced tab. 3. Clear the Always show icon on the taskbar check box. 4.
Setting or changing a power scheme The Power Schemes tab in the Power Options Properties dialog box assigns power levels to system components. You can assign different schemes, depending on whether the computer is running on battery or external power. You can also set a power scheme that initiates standby or turns off the display or hard drive after a time interval that you specify. To set a power scheme: 1. Right-click the Power Meter icon in the notification area, and then click Adjust Power Properties.
16 Chapter 5 Power options ENWW
6 Processor performance controls CAUTION To prevent overheating, do not obstruct vents. Use the computer only on a hard, flat surface. Do not allow another hard surface, such as a printer, or a soft surface, such as pillows, thick rugs, or clothing, to block the airflow. Overheating can damage the computer and reduce processor performance. NOTE In some cases, a computer may operate at a higher speed on external power than on battery power.
Power scheme Processor performance while on external Processor performance while on battery power power Max Battery Performance state is determined based on CPU demand. CPU performance is lower when the Max Battery setting is selected; however, battery life will be extended. * It is recommended that you use the Portable/Laptop power scheme.
7 Batteries When a charged battery is in the computer and the computer is not plugged into external power, the computer runs on battery power. When the computer is plugged into external AC power, the computer runs on AC power. If the computer contains a charged battery and is running on external AC power supplied through the AC adapter, the computer switches to battery power if the AC adapter is disconnected from the computer.
Identifying batteries The computer supports up to 2 batteries: ● One primary lithium-ion battery is included with the computer. ● The optional accessory battery that can be attached to the bottom of the computer. If the computer will be unused and disconnected from external power for more than 2 weeks, remove the battery and store it.
Inserting or removing the primary battery CAUTION To prevent loss of information when removing a battery that is the sole power source, initiate hibernation or turn off the computer before removing the battery. NOTE Batteries vary in appearance by model. To insert a battery: 1. Turn the computer upside down on a flat surface, with the battery bay toward you. 2. Slide the battery (1) into the battery bay until it is seated. The battery release latches (2) automatically lock the battery into place.
3. 22 Remove the battery from the computer (3).
Charging multiple batteries Multiple battery in the system charge and discharge in a preset sequence: ● ● Charge sequence: 1. Primary battery in the computer battery bay 2. Accessory battery Discharge sequence: 1. Accessory battery 2. Primary battery in the computer battery bay While a battery is charging, the battery light on the computer is amber. When the battery is almost fully charged, the battery light is green. The light is turned off when all batteries are fully charged.
Charging a battery To prolong battery life and optimize the accuracy of battery charge displays: WARNING! Do not charge the computer battery on board aircraft. ● ● If you are charging a new battery: ● Charge the battery while the computer is plugged into external power through the AC adapter. ● When you charge the battery, charge it fully before turning on the computer.
NOTE If the computer is on while the battery is charging, the power meter may show 100 percent charge before the battery is fully charged. Displaying charge information on the screen This section explains how to access and interpret battery charge indicators. Viewing charge displays To view information about the status of any battery in the computer: ● Double-click the Power Meter icon in the notification area, at the far right of the taskbar.
Managing low-battery conditions The information in this section describes the alerts and system responses set at the factory. Some lowbattery condition alerts and system responses can be changed using Power Options in Windows Control Panel. Preferences set using Power Options do not affect lights. Identifying low-battery conditions This section explains how to identify low-battery and critical low-battery conditions.
Resolving low-battery conditions CAUTION To reduce the risk of losing information when the computer reaches a critical lowbattery condition and has initiated hibernation, do not restore power until the power lights are turned off.
Calibrating a battery When to calibrate Even if a battery is heavily used, it should not be necessary to calibrate it more than once a month. It is not necessary to calibrate a new battery.
Step 2: Discharging the battery Before you begin a full discharge, disable hibernation. To disable hibernation: 1. Select Start > Control Panel > Performance and Maintenance > Power Options > Hibernate tab. 2. Clear the Enable hibernation check box. 3. Click Apply. The computer must remain on while the battery is being discharged. The battery can discharge whether or not you are using the computer but will discharge faster while the computer is in use.
Step 3: Recharging the battery To recharge the battery: 1. Plug the computer into external power and maintain external power until the battery is fully recharged. When the battery is recharged, the battery light on the computer is turned off. You can use the computer while the battery is recharging, but the battery will charge faster if the computer is off. 2. If the computer is off, turn it on when the battery is fully charged and the battery light is turned off. 3.
Conserving battery power Using the battery conservation procedures and settings described in this section extends the time that a battery can run the computer from a single charge. Conserving power as you work To conserve power as you use the computer: ● Turn off wireless and local area network (LAN) connections and exit modem applications when you are not using them. ● Disconnect external devices that you are not using that are not plugged into an external power source.
NOTE The LAN device is not listed in Device Manager while LAN Power Save mode is activated. To access the LAN device, do one of the following: ● Connect external power. ● Connect a network cable. ● Disable LAN Power Save mode in Computer Setup. Storing a battery WARNING! To avoid potential safety issues, use only the battery provided with the computer, a replacement battery provided by HP, or a compatible battery purchased as an accessory from HP.
Index A AC adapter 4 B battery accessory 20 battery power vs.
34 Index ENWW
