HP ProBook 430 G3 Notebook PC Maintenance and Service Guide
© Copyright 2015, 2018 HP Development Company, L.P. AMD is a trademark of Advanced Micro Devices, Inc. Bluetooth is a trademark owned by its proprietor and used by HP Inc. under license. Intel, Celeron, and Pentium are trademarks of Intel Corporation in the U.S. and other countries. Microsoft and Windows are trademarks of the Microsoft group of companies. The information contained herein is subject to change without notice.
Important Notice about Customer Self-Repair Parts CAUTION: Your computer includes Customer Self-Repair parts and parts that should only be accessed by an authorized service provider. See Chapter 5, "Removal and replacement procedures for Customer Self-Repair parts," for details. Accessing parts described in Chapter 6, "Removal and replacement procedures for Authorized Service Provider only parts," can damage the computer or void your warranty.
iv Important Notice about Customer Self-Repair Parts
Safety warning notice WARNING! To reduce the possibility of heat-related injuries or of overheating the computer, do not place the computer directly on your lap or obstruct the computer air vents. Use the computer only on a hard, flat surface. Do not allow another hard surface, such as an adjoining optional printer, or a soft surface, such as pillows or rugs or clothing, to block airflow.
vi Safety warning notice
Table of contents 1 Product description ....................................................................................................................................... 1 2 Components .................................................................................................................................................. 6 Right ......................................................................................................................................................................
5 Removal and replacement procedures for Customer Self-Repair parts ............................................................. 33 Component replacement procedures .................................................................................................................. 33 Battery ............................................................................................................................................... 34 Service door ............................................................
Setting a MultiBoot Express prompt .............................................................................. 84 Entering MultiBoot Express preferences ........................................................................ 84 Using HP Sure Start (select models only) ............................................................................................................ 84 8 Computer Setup (BIOS) and MultiBoot in Windows 8.1 ..........................................................................
Downloading a BIOS update .............................................................................................................. 98 11 HP PC Hardware Diagnostics (UEFI) .............................................................................................................. 99 Downloading HP PC Hardware Diagnostics (UEFI) to a USB device .................................................................... 99 12 Backup and recovery in Windows 8.1 .................................................
Performing a system recovery .......................................................................................................................... 116 USB Recovery option (select models only) ....................................................................................................... 116 Remove everything and reinstall Ubuntu ......................................................................................................... 117 16 Specifications ........................................
xii
1 Product description Category Description Product Name HP ProBook 430 G3 Notebook PC Processors Intel® Core™ i7 processor, Dual Core, 6th generation (4-MB L3 cache, 15 W) 6500U, 2.6 GHz/3.1 GHz Single Core Turbo Intel® Core i5 processors, Dual Core, 6th generation (3-MB L3 cache, 15 W) 6300U, 2.4-GHz/3.0-GHz Single Core Turbo processor 6200U, 2.3-GHz/2.8-GHz Single Core Turbo processor Intel Core i3 processors, Dual Core, 6th generation (3-MB L3 cache, 15 W) 6100U, 2.
Category Primary storage Mini card solid-state drive Description ● 4096 MB (4096 × 1) ● 2048 MB (2048 × 1) Supports 7-mm, 2.5-in SATA hard drives with HP 3D DriveGuard: ● 1-TB, 5400-rpm ● 500-GB, 7200-rpm ● 500-GB, 5400-rpm ● 500-GB, 5400-rpm, hybrid (8-GB SSD) MLC M.2 2280 solid-state drive (NGFF), SATA-3 Supports the following drives: ● 256 GB TLC ● 128 GB TLC Set as primary storage if selected.
Category Description Wireless Personal Area Network (PAN) only supported by Bluetooth 4.
Category Description 4 cell, 40 Wh, 3.0 Ah, Li-ion battery 2 wire, 1.0 m power cord (for 2 prong adapter) 3 wire, 1.8 m power cord 3 wire, 1.0 m power cord Security Integrated fingerprint reader No fingerprint reader option Security lock TPM SLB9670 (FW ver. 1.2) (Infineon; soldered down) TPM support Operating system Operating system version: Windows 7 Service Pack 1 Windows 8.
Category Description Windows 10 Professional StF MSNA EM Windows 10 Professional 64 Downgrade Windows 7 32 Windows 10 Professional 64 Downgrade Windows 7 32 StF MSNA Windows 10 Professional 64 Downgrade Windows 7 64 Windows 10 Professional 64 Downgrade Windows 7 64 StF MSNA Windows 10 Professional 64 Downgrade Windows 7 64 StF MSNA EM FreeDOS 2.0 Restore Media (DRDVD/SRDVD): DRDVD Windows 10 DRDVD Windows 8.
2 Components Right Component Description (1) USB 3.0 ports (2) Connect an optional USB device, such as a keyboard, mouse, external drive, printer, scanner or USB hub. (2) HDMI port Connects an optional video or audio device, such as a highdefinition television, any compatible digital or audio component, or a high-speed High Definition Multimedia Interface (HDMI) device. (3) External monitor port Connects an external VGA monitor or projector.
Left Component Description (1) Power connector Connects an AC adapter. (2) Battery light When AC power is connected: ● White: The battery charge is greater than 90 percent. ● Amber: The battery charge is from 0 to 90 percent. ● Off: The battery is not charging. When AC power is disconnected (battery not charging): (3) Vent ● Blinking amber: The battery has reached a low battery level. When the battery has reached a critical battery level, the battery light begins blinking rapidly.
Component Description WARNING! To reduce the risk of personal injury, adjust the volume before putting on headphones, earbuds, or a headset. For additional safety information, refer to the Regulatory, Safety, and Environmental Notices. To access this document: Windows 7: Select Start > All Programs > HP Help and Support > HP Documentation. Windows 8.1: From the Start screen, type support, and then select the HP Support Assistant app.
Display Component Description (1) WLAN antennas (2)* (select products only) Send and receive wireless signals to communicate with wireless local area networks (WLANs). (2) WWAN antennas (2)* (select products only) Send and receive wireless signals to communicate with wireless wide area networks (WWANs). (3) Internal microphones (2) Record sound. (4) Webcam light (select products only) On: The webcam is in use. (5) Webcam (select products only) Records video and captures photographs.
Top TouchPad Component 10 Description (1) TouchPad on/off button Turns the TouchPad on and off. (2) TouchPad zone Reads your finger gestures to move the pointer or activate items on the screen. (3) Left TouchPad button Functions like the left button on an external mouse. (4) Right TouchPad button Functions like the right button on an external mouse.
Lights Component (1) Description Power light ● On: The computer is on. ● Blinking: The computer is in the Sleep state, a power-saving state. The computer shuts off power to the display and other unneeded components. ● Off: The computer is off or in Hibernation. Hibernation is a power-saving state that uses the least amount of power. (2) Caps lock light On: Caps lock is on, which switches the key input to all capital letters. (3) Microphone mute light ● Amber: microphone sound is off.
Buttons, speakers, and fingerprint reader Component (1) Description Power button ● When the computer is off, press the button to turn on the computer. ● When the computer is on, press the button briefly to initiate Sleep. ● When the computer is in the Sleep state, press the button briefly to exit Sleep. ● When the computer is in Hibernation, press the button briefly to exit Hibernation. CAUTION: Pressing and holding down the power button results in the loss of unsaved information.
Component Description (2) Speakers (2) Produce sound. (3) Wireless button Turns the wireless feature on or off but does not establish a wireless connection. A wireless network must be set up before a wireless connection is possible. (4) Volume mute button Mutes and restores speaker sound. (5) Fingerprint reader (select products only) Allows a fingerprint logon to Windows, instead of a password logon.
Component Description (5) Embedded numeric keypad A numeric keypad superimposed over the keyboard alphabet keys that enables you to add, subtract, and perform other numeric tasks. When num lock is on, the keypad can be used like an external numeric keypad. (6) Windows application key Windows 7: Displays a shortcut menu for items beneath the cursor. Windows 8.1: Displays options for a selected object. Windows 10: Displays options for a selected object.
Bottom Component Description (1) Battery release latches (2) Release the battery. (2) Battery bay Holds the battery. (3) Vents (3) Enable airflow to cool internal components. NOTE: The computer fan starts up automatically to cool internal components and prevent overheating. It is normal for the internal fan to cycle on and off during routine operation. NOTE: The vents shown in this illustration may vary depending on your computer model.
Component Description CAUTION: To prevent an unresponsive system, replace the wireless module only with a wireless module authorized for use in the computer by the governmental agency that regulates wireless devices in your country or region. If you replace the module and then receive a warning message, remove the module to restore computer functionality, and then contact support. To access Help and Support in Windows 7: Select Start > Help and Support. To access HP Support Assistant: in Windows 8.
Labels The labels affixed to the computer provide information you may need when you troubleshoot system problems or travel internationally with the computer. IMPORTANT: Check the following locations for the labels described in this section: the bottom of the computer, inside the battery bay, under the service door, or on the back of the display. ● Service label—Provides important information to identify your computer.
Inserting a SIM card (select products only) CAUTION: To prevent damage to the connectors, use minimal force when inserting a SIM card. To insert a SIM card, follow these steps: 1. Turn off the computer by using the Shut down command. 2. Close the display. 3. Disconnect all external devices connected to the computer. 4. Unplug the power cord from the AC outlet. 5. Turn the computer upside down on a flat surface, with the battery bay toward you. 6. Remove the battery. 7.
3 Illustrated parts catalog Computer major components NOTE: HP continually improves and changes product parts. For complete and current information on supported parts for your computer, go to http://partsurfer.hp.com, select your country or region, and then follow the on-screen instructions. NOTE: Details about your computer, including model, serial number, product key, and length of warranty, are on the service tag at the bottom of your computer. See Labels on page 17 for details.
Item Description (1) Display panel assembly, 33.8-cm (13.3-inch) Spare part number NOTE: Touch displays are not spared an the subcomponent level – touch display are only spared as full hinge-ups. Non-touch displays are ONLY spared at the subcomponent level – non-touch displays are not spared as full-hinge-ups. For more information about non-touch display components, see Display components on page 23.
Item Description Spare part number Intel Core i3-6100U processor 830935-xxx Intel Core i3-6100U processor for use in models with WWAN 830936-xxx Intel Core i3-6100U processor for use in models with DDR4 memory 855655-xxx Intel Core i3-6100U processor for use in models with WWAN and DDR4 memory 855665-xxx Intel Core i3-6006U processor 913645-xxx Intel Pentium 4405U processor 830942-xxx Intel Pentium 4405U processor for use in models with WWAN 861550-xxx Intel Pentium 4405U processor for use
Item Description (18) WWAN module (HP ProBook 450 G3 models only) (19) (20) HP lt4110 LTE/HSPA+ Intel Mobile Broadband Module 812954-001 HP hs3110 HSPA+ Intel Mobile Broadband Module 793516-001 Base enclosure For use in models with DDR3L memory 826370-001 For use in models with DDR4 memory 855668-001 Hard drive 1 TB, 5400 rpm, 7 mm 762990-001 750 GB, 5400 rpm, 7 mm 752099-001 500 GB, 5400 rpm, 7 mm 778186-001 500 GB, 5400 rpm, 7 mm, hybrid (8-GB SSD) 732000-001 500 GB, 7200 rpm, 7 mm
Display components Item Description (1) Display bezel Spare part number For use in models with a webcam 826371-001 For use in models without a webcam 826372-001 Webcam module 826395-001 Microphone module 826385-001 (3) Display panel (raw) 826377-001 (4) Display Hinge Kit, includes: 826384-001 (2) Left hinge Right hinge Display components 23
Item Description Spare part number (5) Display/webcam cable assembly 826373-001 (Cable Kit) Included in Cable Kit, 826373-001 (6) Display rear cover (includes wireless antennas) For use in models without WWAN 826369-001 For use in models with WWAN 828887-001 Description Spare part number Cable Kit 826373-001 Cable Kit Item 24 (1) Power button board cable (2) USB/audio/card reader cable (3) Function board cable (4) Battery connector cable (5) Display/webcam cable Chapter 3 Illustr
Mass storage devices Item (1) Description Spare part number Hard Drive Hardware Kit, includes: 826382-001 Hard drive bracket Screws (not illustrated) (2) (3) Hard drives 1 TB, 5400 rpm, 7 mm 762990-001 750 GB, 5400 rpm, 7 mm 752099-001 500 GB, 5400 rpm, 7 mm 778186-001 500 GB, 5400 rpm, 7 mm, hybrid (8-GB SSD) 732000-001 500 GB, 7200 rpm, 7 mm 703267-001 Solid-state drives, M.
Plastics Kit Item Description Spare part number Plastics Kit 826386-001 (1) Service door (2) Fingerprint reader insert (for use in models without a fingerprint reader) Miscellaneous parts Description Spare part number AC adapters 65-W Smart AC power adapter, 4.5 mm barrel connector (for use only in Asia, the People’s Republic of China, and India) 714657-001 45-W AC adapter, 4.5 mm barrel connector (for use in Japan) 742436-001 45-W AC adapter, 4.
Description Spare part number South Korea 267836-001 Switzerland 213354-001 Taiwan 393313-001 Thailand 285096-001 United Kingdom and Singapore 213351-001 Power cord (3-pin, C5, black, 1.
4 Removal and replacement procedures preliminary requirements Tools required You will need the following tools to complete the removal and replacement procedures: ● Flat-bladed screwdriver ● Non-marking, non-conductive pry tool ● Phillips P1 screwdriver ● Torx T8 screwdriver Service considerations The following sections include some of the considerations that you must keep in mind during disassembly and assembly procedures.
Cables and connectors CAUTION: When servicing the computer, be sure that cables are placed in their proper locations during the reassembly process. Improper cable placement can damage the computer. Cables must be handled with extreme care to avoid damage. Apply only the tension required to unseat or seat the cables during removal and insertion. Handle cables by the connector whenever possible. In all cases, avoid bending, twisting, or tearing cables.
Grounding guidelines Electrostatic discharge damage Electronic components are sensitive to electrostatic discharge (ESD). Circuitry design and structure determine the degree of sensitivity. Networks built into many integrated circuits provide some protection, but in many cases, ESD contains enough power to alter device parameters or melt silicon junctions. A discharge of static electricity from a finger or other conductor can destroy static-sensitive devices or microcircuitry.
Packaging and transporting guidelines Follow these grounding guidelines when packaging and transporting equipment: ● To avoid hand contact, transport products in static-safe tubes, bags, or boxes. ● Protect ESD-sensitive parts and assemblies with conductive or approved containers or packaging. ● Keep ESD-sensitive parts in their containers until the parts arrive at static-free workstations. ● Place items on a grounded surface before removing items from their containers.
Equipment guidelines Grounding equipment must include either a wrist strap or a foot strap at a grounded workstation. ● When seated, wear a wrist strap connected to a grounded system. Wrist straps are flexible straps with a minimum of one megohm ±10% resistance in the ground cords. To provide proper ground, wear a strap snugly against the skin at all times. On grounded mats with banana-plug connectors, use alligator clips to connect a wrist strap.
5 Removal and replacement procedures for Customer Self-Repair parts CAUTION: The Customer Self-Repair program is not available in all locations. Installing a part not supported by the Customer Self-Repair program may void your warranty. Check your warranty to determine if Customer Self-Repair is supported in your location. NOTE: HP continually improves and changes product parts. For complete and current information on supported parts for your computer, go to http://partsurfer.hp.
Battery Description Spare part number 6-cell, 55 WHr, 2.8 Ah 811347-001 4-cell, 44 WHr, 3.0 Ah 805292-001 4-cell, 41 WHr, 2.8 Ah L07042-850 4-cell, 40 WHr, 3.0 Ah 805291-001 Before removing the battery, follow these steps: 1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system. 2. Disconnect all external devices connected to the computer. 3.
Service door Description Spare part number Plastics Kit (includes service door) 826386-001 Before removing the service door, follow these steps: 1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system. 2. Disconnect all external devices connected to the computer. 3.
Hard drive Description Spare part number Hard drives 1 TB, 5400 rpm, 7 mm 762990-001 750 GB, 5400 rpm, 7 mm 752099-001 500 GB, 5400 rpm, 7 mm 778186-001 500 GB, 5400 rpm, 7 mm, hybrid (8-GB SSD) 732000-001 500 GB, 7200 rpm, 7 mm 703267-001 Before removing the hard drive, follow these steps: 1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system. 2.
3. Remove the hard drive from the bay (3). 4. To remove the hard drive cover from the hard drive, remove the 4 Phillips PM3.0×3.5 screws (1) that secure the bracket to the drive, and then lift the cover off the drive (2). Reverse these procedures to install a hard drive.
Memory modules Description Spare part number 2-GB (DDR4, 2133 MHz) 851379-001 4-GB (DDR4, 2133 MHz) 820569-001 8-GB (DDR4, 2133 MHz) 820570-001 2-GB (DDR3L-12800, 1600 MHz) 691739-001 4-GB (DDR3L-12800, 1600 MHz) 691740-001 8-GB (DDR3L-12800, 1600 MHz) 693374-001 Update BIOS before adding memory modules Before adding new memory, make sure you update the computer to the latest BIOS.
2. Remove the memory module (2) by pulling the module away from the slot at an angle. NOTE: Memory modules are designed with a notch to prevent incorrect insertion into the memory module slot. NOTE: The computer uses two memory sockets. The top socket houses the expansion memory module and the bottom socket houses the primary memory module. The removal procedure is the same for both memory sockets. Reverse this procedure to install a memory module.
WLAN/Bluetooth combo card The computer uses a card that provides both WLAN and Bluetooth functionality. Description Spare part number Broadcom Nami 43142 b/g/n 1×1 + Bluetooth 4 combo adapter (MOW) 792608-001 Realtek RTL8188EE 802.11b/g/n 1×1 Wi-Fi Adapter (Worldwide) 792609-001 Realtek RTL8723BE 802.11b/g/n 1×1 Wi-Fi + BT4.0 Combo Adapter (Worldwide 792610-001 Realtek RTL8723BE bgn 1×1 + Bluetooth 4.0 Combo Adapter (Worldwide) 792611-001 Intel Dual Band Wireless-AC 7265NV (non v-Pro) 802.
3. Remove the WLAN module (3) by pulling the module away from the slot at an angle. NOTE: WLAN modules are designed with a notch to prevent incorrect insertion. NOTE: If the WLAN antennas are not connected to the terminals on the WLAN module, the protective sleeves must be installed on the antenna connectors, as shown in the following illustration. Reverse this procedure to install the WLAN module.
WWAN module Description Spare part number HP lt4110 LTE/HSPA+ Intel Mobile Broadband Module 812954-001 HP hs3110 HSPA+ Intel Mobile Broadband Module 793516-001 Before removing the WWAN module, follow these steps: 1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system. 2. Disconnect all external devices connected to the computer. 3.
3. Remove the WWAN module (3) by pulling the module away from the slot at an angle. NOTE: WWAN modules are designed with a notch to prevent incorrect insertion. NOTE: If the WWAN antennas are not connected to the terminals on the WWAN module, the protective sleeves must be installed on the antenna connectors, as shown in the following illustration. Reverse this procedure to install the WWAN module.
M.2 solid-state drive Description Spare part number 256 GB, TLC 826393-001 128 GB, TLC 826392-001 64 GB 921344-001 Before removing the solid-state drive, follow these steps: 1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system. 2. Disconnect all external devices connected to the computer. 3.
Keyboard In this section, the first table provides the main spare part number for the keyboards. The second table provides the country codes.
46 2. Open the computer and position it on its side with the bottom toward you. 3. Insert a tool into the access hole in the bottom of the computer and push to disengage the keyboard from the top cover.
4. Lift the top of the keyboard upward (1), and then lift the keyboard up at an angle (2) to disengage the tabs at the bottom of the keyboard. NOTE: A cable (or cables) connect the bottom of the keyboard to the system board. Make sure not to prematurely pull the cables out of the system board connector. 5. Rotate the keyboard until it rests on the palm rest (1). 6. Disconnect the keyboard cable by lifting the connector latch (2), and then disconnect the keyboard cable from the system board (3).
7. If applicable, disconnect the backlight cable by lifting the connector latch (4), and then disconnect the cable from the system board (5). 8. Remove the keyboard. Reverse this procedure to install the keyboard. When installing a keyboard, to make sure the keyboard lays flat, the keyboard ribbon cable must be bent at the appropriate point before installation. There are markings, typically a thin white line across the breadth of the cable, that indicate where to bend the cable.
Component replacement procedures 49
6 Removal and replacement procedures for Authorized Service Provider parts CAUTION: Components described in this chapter should only be accessed by an authorized service provider. Accessing these parts can damage the computer or void the warranty. NOTE: HP continually improves and changes product parts. For complete and current information on supported parts for your computer, go to http://partsurfer.hp.com, select your country or region, and then follow the on-screen instructions.
1. Position the computer upside-down with the front toward you. 2. Remove the 2 large rubber screw covers on each side of the battery (1), 2 rubber screw covers near the middle sides (2), 3 small rubber screw covers from the bottom corners (3), and large screw cover near the bottom of the computer (4). 3. Remove the 8 Torx T8M2.5×6.0 screws (1) and the broadhead Phillips PM2.5×2.5 screw (2) that secures the top cover to the computer. 4. Position the computer upright and open it as far as possible.
52 5. Remove the 5 Torx T8M2.5×6.0 screws from the top of the computer. 6.
7. Pry the top cover off the computer starting at the top (1), and then lift the top cover off the computer (2). NOTE: The top cover may be difficult to remove from the computer. Be careful not to damage the top cover when attempting to remove it. Reverse this procedure to install the top cover.
Fingerprint reader assembly Description Spare part number Fingerprint reader assembly (includes cable and bracket) 826380-001 Fingerprint reader insert (part of the Plastics Kit; for use in models without a fingerprint reader) 826386-001 Before removing the fingerprint reader assembly, follow these steps: 1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system. 2.
3. Lift the fingerprint reader board to disengage the adhesive that secures it, and then remove the board and cable assembly from the top cover (3). Reverse this procedure to install the fingerprint reader assembly.
Power button board Description Spare part number Power button board assembly 826387-001 Power button board cable (included in Cable Kit) 826373-001 Before removing the power button board, follow these steps: 1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system. 2. Disconnect all external devices connected to the computer. 3.
4. Remove the board from the top cover (3). Reverse this procedure to install the power button board.
Function board Description Spare part number Function board 826381-001 Function board cable (included in Cable Kit) 826373-001 Before removing the function board, follow these steps: 1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system. 2. Disconnect all external devices connected to the computer. 3.
4. Remove the board from the top cover (3). 5. Remove the function board from the top cover. Reverse this procedure to install the function board.
USB/audio/card reader board Description Spare part number USB/audio/card reader board 826374-001 USB/audio/card reader board cable (included in Cable Kit) 826373-001 Before removing the USB/audio/card reader board, follow these steps: 1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system. 2. Disconnect all external devices connected to the computer. 3.
5. Lift the rear of the board and pull it away from side of the top cover (4). Reverse this procedure to install the USB/audio/card reader board.
Fan Description Spare part number Fan 826379-001 NOTE: To properly ventilate the computer, allow at least 7.6 cm (3.0 in) of clearance on the left side of the computer. The computer uses an electric fan for ventilation. The fan is controlled by a temperature sensor and is designed to turn on automatically when high temperature conditions exist.
3. Lift the fan from the computer (3). Reverse this procedure to install the fan.
Battery connector cable The battery connector cable is included in the Cable Kit, spare part number 826373-001. Before removing the battery connector cable, follow these steps: 1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system. 2. Disconnect all external devices connected to the computer. 3.
System board NOTE: All system board spare part kits include replacement thermal material. All system boards use the following part numbers: xxxxxx-001: Windows 7 or non-Windows operating systems xxxxxx-601: Windows 8.
4. Remove the battery (see Battery on page 34). 5. Remove the following components: a. Service door (see Service door on page 35). b. Hard drive (see Hard drive on page 36) c. Keyboard (see Keyboard on page 45) d.
4. Lift the left side of the system board up at an angle, and then remove the system board from the computer (2). Reverse this procedure to install the system board.
RTC battery Description Spare part number RTC battery 826388-001 Before removing the RTC battery, follow these steps: 1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system. 2. Disconnect all external devices connected to the computer. 3. Disconnect the power from the computer by first unplugging the power cord from the AC outlet, and then unplugging the AC adapter from the computer. 4.
Reverse this procedure to install the RTC battery. Speaker assembly Description Spare part number Speaker assembly 826391-001 Before removing the speaker assembly, follow these steps: 1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system. 2. Disconnect all external devices connected to the computer. 3.
3. Remove the speakers from the top cover (2). NOTE: When reinstalling the speakers, make sure the rubber gaskets in each screw hole (3) are correctly in place. Reverse this procedure to install the speaker assembly.
Heat sink assembly All heat sink assembly spare part kits include replacement thermal material. Description Spare part number Heat sink 826383-001 Before removing the heat sink assembly, follow these steps: 1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system. 2. Disconnect all external devices connected to the computer. 3.
3. Lift the heat sink from the system board (5). 4. Lift the heat sink from the system board (5). NOTE: Thoroughly clean thermal material from the surfaces of the system board component (1) and the heat sink (2) each time you remove the heat sink. All heat sink and processor spare part kits include thermal material. Reverse this procedure to install the heat sink assembly.
Display assembly Description Spare part number Display panel assembly, touch screen, one antenna 826375-001 Display panel assembly, touch screen, two antennas 826376-001 Before removing the display assembly, follow these steps: 1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system. 2. Disconnect all external devices connected to the computer. 3.
5. Lift the display assembly straight up and remove it (4). CAUTION: When installing the display assembly, be sure that the wireless antenna cables are routed and arranged properly. Failure to properly route the antennas can result in degradation of the computer's wireless performance. 74 6. To remove the display bezel, remove the 2 screw covers (1) and the 2 Phillips PM2.0×4.0 screws (2) from the bottom corners of the display bezel. 7.
8. Remove the display bezel (6). The display bezel is available using spare part number 826371-001 for models with a webcam and 826372-001 for models without a webcam. Display bezel mylar screw covers are available in the Rubber Kit, spare part number 826389-001. 9. If it is necessary to replace the webcam or microphone module, disconnect the cable from the module (1), and then gently pull the module away from the double-sided tape on the display enclosure (2).
10. If it is necessary to remove the display panel from the enclosure, remove the 4 Phillips PM2.0×4.0 screws (1) that secure the panel to the display enclosure, and then rotate the top of the panel all the way over (2). The raw display panel is available using spare part number 826377-001. 11. Lift the cable connector bracket (1), disconnect the display cable from the rear of the panel (2), and then remove the display panel (3) from the enclosure. 12.
13. Remove the display hinges from the display enclosure (2). Display hinges are available in the Display Hinge Kit using spare part number 826384-001. 14. If it is necessary to replace the display/webcam cable, remove the cable from the clips on the display enclosure (1), and then lift the cable straight up and off the display panel (2). The display/webcam cable is available in the Cable Kit using spare part number 826373-001. Reverse this procedure to reassemble and install the display assembly.
Power connector and cable Description Spare part number Power connector and cable 827039-001 Before removing the power cable, follow these steps: 1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system. 2. Disconnect all external devices connected to the computer. 3.
4. Remove the cable from the clips around the fan (4), and then lift the power cable from the computer (5). Reverse this procedure to install the power cable.
7 Computer Setup (BIOS) and MultiBoot in Windows 7 Using Computer Setup Computer Setup, or Basic Input/Output System (BIOS), controls communication between all the input and output devices on the system (such as disk drives, display, keyboard, mouse, and printer). Computer Setup includes settings for the types of devices installed, the startup sequence of the computer, and the amount of system and extended memory. NOTE: Use extreme care when making changes in Computer Setup.
Use the arrow keys to select Main > Ignore Changes and Exit, and then press enter. ● To save your changes and exit Computer Setup menus: Click the Save icon in the lower-right corner of the screen, and then follow the on-screen instructions. – or – Use the arrow keys to select Main > Save Changes and Exit, and then press enter. Your changes go into effect when the computer restarts. Restoring factory settings in Computer Setup NOTE: Restoring defaults will not change the hard drive mode.
Use the arrow keys to select Main > Ignore Changes and Exit, and then press enter. Downloading a BIOS update CAUTION: To reduce the risk of damage to the computer or an unsuccessful installation, download and install a BIOS update only when the computer is connected to reliable external power using the AC adapter. Do not download or install a BIOS update while the computer is running on battery power, docked in an optional docking device, or connected to an optional power source.
optical drives, diskette drives, a network interface card (NIC), hard drives, and USB devices. Boot devices contain bootable media or files that the computer needs to start and operate properly. NOTE: Some boot devices must be enabled in Computer Setup before they can be included in the boot order. You can change the order in which the computer searches for a boot device by changing the boot order in Computer Setup.
Setting a MultiBoot Express prompt To start Computer Setup and set the computer to display the MultiBoot startup location menu each time the computer is started or restarted, follow these steps: 1. Turn on or restart the computer, and then press esc while the “Press the ESC key for Startup Menu” message is displayed at the bottom of the screen. 2. Press f10 to enter Computer Setup. 3. Use a pointing device or the arrow keys to select System Configuration > Boot Options, and then press enter. 4.
8 Computer Setup (BIOS) and MultiBoot in Windows 8.1 Using Computer Setup Computer Setup, or Basic Input/Output System (BIOS), controls communication between all the input and output devices on the system (such as disk drives, display, keyboard, mouse, and printer). Computer Setup includes settings for the types of devices installed, the startup sequence of the computer, and the amount of system and extended memory. NOTE: Use extreme care when making changes in Computer Setup.
To exit Computer Setup menus, choose one of the following methods: ● To exit Computer Setup menus without saving your changes: Click the Exit icon in the lower-right corner of the screen, and then follow the on-screen instructions. – or – Use the arrow keys to select Main > Ignore Changes and Exit, and then press enter. ● To save your changes and exit Computer Setup menus: Click the Save icon in the lower-right corner of the screen, and then follow the on-screen instructions.
To use Setup Utility (BIOS): 1. Start Computer Setup. 2. Use a pointing device or the arrow keys to select Main > System Information. 3. To exit Computer Setup without saving your changes, click the Exit icon in the lower-right corner of the screen, and then follow the on-screen instructions. – or – Use the arrow keys to select Main > Ignore Changes and Exit, and then press enter. To check for later BIOS versions, see Downloading a BIOS update on page 87.
NOTE: After a message on the screen reports a successful installation, you can delete the downloaded file from your hard drive. Using MultiBoot About the boot device order As the computer starts, the system attempts to boot from enabled devices. The MultiBoot utility, which is enabled at the factory, controls the order in which the system selects a boot device. Boot devices can include optical drives, diskette drives, a network interface card (NIC), hard drives, and USB devices.
To move the device down in the boot order, use a pointing device to click the down arrow, or press the key. 5. To save your changes and exit Computer Setup, click the Save icon in the lower-left corner of the screen, and then follow the on-screen instructions. – or – Use the arrow keys to select Main > Save Changes and Exit, and then press enter. Dynamically choosing a boot device using the f9 prompt To dynamically choose a boot device for the current startup sequence, follow these steps: 1.
Using HP Sure Start (select models only) Select computer models are configured with HP Sure Start, a technology that continuously monitors the computer's BIOS for attacks or corruption. If the BIOS becomes corrupted or is attacked, HP Sure Start automatically restores the BIOS to its previously safe state, without user intervention. HP Sure Start is configured and already enabled so that most users can use the HP Sure Start default configuration.
9 Computer Setup (BIOS), TPM, and HP Sure Start in Windows 10 Using Computer Setup Computer Setup, or Basic Input/Output System (BIOS), controls communication between all the input and output devices on the system (such as disk drives, display, keyboard, mouse, and printer). Computer Setup includes settings for the types of devices installed, the startup sequence of the computer, and the amount of system and extended memory. NOTE: Use extreme care when making changes in Computer Setup.
To exit Computer Setup menus, choose one of the following methods: ● To exit Computer Setup menus without saving your changes: Select the Exit icon in the lower-right corner of the screen, and then follow the on-screen instructions. – or – Select Main, select Ignore Changes and Exit, and then press enter. ● To save your changes and exit Computer Setup menus: Select the Save icon in the lower-right corner of the screen, and then follow the on-screen instructions.
Updating the BIOS Updated versions of the BIOS may be available on the HP website. Most BIOS updates on the HP website are packaged in compressed files called SoftPaqs. Some download packages contain a file named Readme.txt, which contains information regarding installing and troubleshooting the file. Determining the BIOS version To decide whether you need to update Computer Setup (BIOS), first determine the BIOS version on your computer.
NOTE: If you connect your computer to a network, consult the network administrator before installing any software updates, especially system BIOS updates. BIOS installation procedures vary. Follow any instructions that are revealed on the screen after the download is complete. If no instructions are revealed, follow these steps: 1. Type file in the taskbar search box, and then select File Explorer. 2. Select your hard drive designation. The hard drive designation is typically Local Disk (C:). 3.
Using HP Sure Start (select products only) Select computer models are configured with HP Sure Start, a technology that continuously monitors the computer's BIOS for attacks or corruption. If the BIOS becomes corrupted or is attacked, HP Sure Start automatically restores the BIOS to its previously safe state, without user intervention. HP Sure Start is configured and already enabled so that most users can use the HP Sure Start default configuration.
10 Computer Setup (BIOS) in Ubuntu Linux Computer Setup, or Basic Input/Output System (BIOS), controls communication between all the input and output devices on the system (such as disk drives, display, keyboard, mouse, and printer). Computer Setup includes settings for the types of peripherals installed, the startup sequence of the computer, and the amount of system and extended memory. NOTE: Use extreme care when making changes in Computer Setup. Errors can prevent the computer from operating properly.
– or – ● To save your changes and exit Computer Setup menus, click the Save icon in the lower-left corner of the screen, and then follow the on-screen instructions. – or – Use the arrow keys to select Main > Save Changes and Exit, and then press enter. Your changes go into effect when the computer restarts. Restoring factory settings in Computer Setup NOTE: Restoring defaults will not change the hard drive mode.
NOTE: You can also determine the BIOS version by turning on or restarting the computer, pressing the esc key while the “Press the ESC key for Startup Menu” message is displayed at the bottom of the screen, and then pressing the f1 key. Follow the on-screen instructions to exit this screen.
11 HP PC Hardware Diagnostics (UEFI) HP PC Hardware Diagnostics is a Unified Extensible Firmware Interface (UEFI) that allows you to run diagnostic tests to determine whether the computer hardware is functioning properly. The tool runs outside the operating system so that it can isolate hardware failures from issues that are caused by the operating system or other software components.
4. Select your computer, and then select your operating system. 5. In the Diagnostic section, follow the on-screen instructions to select and download the UEFI version you want.
12 Backup and recovery in Windows 8.1 To protect your information, use Windows backup and restore utilities to back up individual files and folders, back up your entire hard drive, create system repair media (select models only) by using the installed optical drive (select models only) or an optional external optical drive, or create system restore points. In case of system failure, you can use the backup files to restore the contents of your computer.
CAUTION: Some Startup Repair options will completely erase and reformat the hard drive. All files you have created and any software installed on the computer are permanently removed. When reformatting is complete, the recovery process restores the operating system, as well as the drivers, software, and utilities from the backup used for recovery. 1. If possible, back up all personal files. 2. If possible, check for the presence of the Recovery Image partition and the Windows partition.
Using Windows operating system media (purchased separately) To order a Windows operating system DVD, contact support. See the Worldwide Telephone Numbers booklet included with the computer. You can also find contact information from the HP website. Go to http://www.hp.com/support, select your country or region, and follow the on-screen instructions. CAUTION: Using a Windows operating system media completely erases hard drive contents and reformats the hard drive.
13 Backup and recovery in Windows 7 Your computer includes HP and Windows tools to help you safeguard your information and retrieve it if you ever need to. These tools will help you return your computer to a proper working state, all with simple steps. This section provides information about the following processes: ● Creating recovery media and backups ● Restoring and recovering your system Creating recovery media and backups Recovery after a system failure is only as good as your most recent backup.
applications if the hard drive becomes corrupted. HP Recovery Disc Creator can create two kinds of recovery DVDs: ● Windows 7 operating system DVD—Installs the operating system without additional drivers or applications. ● Driver Recovery DVD—Installs specific drivers and applications only, in the same way that the HP Software Setup utility installs drivers and applications. Creating recovery media NOTE: The Windows 7 operating system DVD can be created only once.
To create a backup using Windows Backup and Restore: NOTE: The backup process may take over an hour, depending on file size and the speed of the computer. 1. Select Start > All Programs > Maintenance > Backup and Restore. 2. Follow the on-screen instructions to set up your backup, create a system image (select models only), or create system repair media (select models only).
1. If possible, back up all personal files. 2. If possible, check for the presence of the Windows partition. To check for the Windows partition, select Start > Computer. NOTE: If the Windows partition is not listed, you must recover your operating system and programs using the Windows 7 operating system DVD and the Driver Recovery media. For additional information, see Using Windows 7 operating system media on page 107. 3.
To initiate recovery using a Windows 7 operating system DVD: NOTE: This process takes several minutes. 1. If possible, back up all personal files. 2. Restart the computer, and then insert the Windows 7 operating system DVD into the optical drive before the Windows operating system loads. 3. When prompted, press any keyboard key. 4. Follow the on-screen instructions. 5. Click Next. 6. Select Repair your computer. 7. Follow the on-screen instructions. After the repair is completed: 1.
14 Backup and recovery in Windows 10 This chapter provides information about the following processes. The information in the chapter is standard procedure for most products. ● Creating recovery media and backups ● Restoring and recovering your system For additional information, refer to the HP support assistant app. ▲ Type support in the taskbar search box, and then select the HP Support Assistant app. ‒ or – Click the question mark icon in the taskbar.
You can use Windows tools to create system restore points and create backups of personal information, see Using Windows tools on page 110. ● If your computer does list the Recovery partition and the Windows partition, you can use HP Recovery Manager to create recovery media after you successfully set up the computer. HP Recovery media can be used to perform system recovery if the hard drive becomes corrupted.
Restore and recovery There are several options for recovering your system. Choose the method that best matches your situation and level of expertise: IMPORTANT: ● Windows offers several options for restoring from backup, refreshing the computer, and resetting the computer to its original state. For more information see the Get started app. ▲ ● Not all methods are available on all products. Select the Start button, and then select the Get started app.
website. Go to http://www.hp.com/support, select your country or region, and follow the on-screen instructions. IMPORTANT: HP Recovery Manager does not automatically provide backups of your personal data. Before beginning recovery, back up any personal data you want to retain. Using HP Recovery media, you can choose from one of the following recovery options: NOTE: Only the options available for your computer display when you start the recovery process.
Changing the computer boot order If your computer does not restart in HP Recovery Manager, you can change the computer boot order, which is the order of devices listed in BIOS where the computer looks for startup information. You can change the selection to an optical drive or a USB flash drive. To change the boot order: IMPORTANT: For a tablet with a detachable keyboard, connect the keyboard to the keyboard dock before beginning these steps. 1. Insert the HP Recovery media. 2.
Removing the HP Recovery partition (select products only) HP Recovery Manager software allows you to remove the HP Recovery partition to free up hard drive space. IMPORTANT: After you remove the HP Recovery partition, you will not be able to perform System Recovery or create HP recovery media from the HP Recovery partition. So before you remove the Recovery partition, create HP Recovery media; see Creating HP Recovery media (select products only) on page 109.
15 Backup and Recovery in Ubuntu Linux Recovery after a system failure is as good as your most recent backup. As you add new software and data files, you should continue to back up your system on a regular basis to maintain a reasonably current backup. Your computer includes tools provided by HP to help you safeguard your information and retrieve it if ever needed. Creating backups 1. Create restore media immediately after you set up the computer.
NOTE: If multiple backups have been performed, click Use the latest version to restore the latest version. 6. Click Restore to start restoring the files, or click Cancel to cancel the operation. Performing a system recovery Recovery allows you to repair or restore the computer to its original factory state. You can create an HP Factory Image, using an installed or an external DVD±RW optical drive. NOTE: Your computer may not come equipped with an internal optical drive.
NOTE: HP recommends that you create the USB Recovery Disk in the event of a system failure. The Disk On Key used for this process should be 4 GB or larger. Creating a USB Recovery Disk On Key 1. Connect the USB Disk On Key to a USB port on the computer. 2. Select Computer > More applications > Tools > Create Recovery USB. 3. Enter the root password when prompted. 4. Select USB Disk On Key from the list. 5. Click OK. 6.
You can initiate this option by using the f11 key. To use the f11 key: Press f11 while the computer boots. – or – Press and hold f11 as you press the power button. The following options are available: ● Cancel/Reboot—Reboots the system. No recovery or restore activity is performed. ● Recover/Repair System—This option repairs a system that is not working properly and preserves user data. ● Restore Factory System—This option restores the system back to the original factory state.
16 Specifications Computer specifications Metric U.S. (Non-touch) 233.5 mm 9.19 in (Touch) 233.7 mm 9.20 in Width 326.0 mm 12.83 in (Non-touch) 19.9 to 20.9 mm 0.78 to 0.83 in (Touch) 21.4 to 22.4 mm 0.84 to 0.88 in Non-touch (equipped with 1 DIMM, M.2 SSD, WLAN module, webcam, 4 cell battery) 1.5 kg 3.31 lbs Non-touch (equipped with 1 DIMM, hard drive, WLAN module, webcam, 4 cell battery) 1.6 kg 3.53 lbs Touch (equipped with 1 DIMM, M.2 SSD, WLAN module, webcam, 4 cell battery) 1.
Metric Operating 10% to 90% Nonoperating 5% to 95% U.S. Maximum altitude (unpressurized) Operating (14.7 to 10.1 psia) -15 m to 3,048 m 50 ft to 10,000 ft Nonoperating (14.7 to 4.4 psia) -15 m to 12,192 m -50 ft to 40,000 ft Shock Operating 125 g, 2 ms, half-sine Nonoperating 200 g, 2 ms, half-sine Random vibration Operating 0.75 g zero-to-peak, 10 Hz to 500 Hz, 0.25 oct/min sweep rate Nonoperating 1.50 g zero-to-peak, 10 Hz to 500 Hz, 0.
Hard drive specifications 1-TB* 750-GB* 500-GB* 500-GB* hybrid Height 9.5 mm 9.5 mm 9.5 mm or 7.0 mm 7.0 mm Width 70 mm 70 mm 70 mm 70 mm Weight 115 g 102 g 101 g or 95 g 95 g Interface type SATA SATA SATA SATA Transfer rate 100 MB/sec 100 MB/sec 100 MB/sec 100 MB/sec Security ATA security ATA security ATA security ATA security Dimensions Seek times (typical read, including setting) Single track 1.4 ms 1.
Solid-state drive specifications 128-GB* 256-GB* Height 1.35 mm 1.35 mm Weight < 10 g < 10 g Form factor M.2 2280-D2-B-M M.2 2280-D2-B-M Transfer rate up to 540 MB/sec up to 540 MB/sec Interface type SATA-3 SATA-3 Ready time, maximum (to not busy) 1.0 ms < 1.0 ms Access times, logical 0.1 ms 0.1 ms Total logical sectors 234,441,648 468,883,296 Operating temperature 0°C to 70°C (32°F to 158°F) *1 GB = 1 billion bytes when referring to hard drive storage capacity.
17 Statement of memory volatility The purpose of this chapter is to provide general information regarding nonvolatile memory in HP Business PCs. This chapter also provides general instructions for restoring nonvolatile memory that can contain personal data after the system has been powered off and the hard drive has been removed. HP Business PC products that use Intel®-based or AMD®-based system boards contain volatile DDR memory.
g. If a DriveLock password is set, select the Security menu, and scroll down to Hard Drive Utilities under the Utilities menu. Select Hard Drive Utilities, select DriveLock, then uncheck the checkbox for DriveLock password on restart. Select OK to proceed. h. Select the Main menu, and then select Reset BIOS Security to factory default. Click Yes at the warning message. The computer will reboot. i.
NOTE: If the system has a BIOS administrator password, enter the password at the prompt. 2. a. Select Main, select Restore Defaults, and then select Yes to load defaults. b. Select the Security menu, select Restore Security Level Defaults, and then select Yes to restore security level defaults. c. If an asset or ownership tag is set, select the Security menu and scroll down to the Utilities menu. Select System IDs, and then select Asset Tracking Number.
NOTE: The amount of time it takes for Disk Sanitizer to run can take several hours. Plug the computer into an AC outlet before starting. a. Turn on or restart the computer, and then press esc while the “Press the ESC key for Startup Menu” message is displayed at the bottom of the screen. b. Select the Security menu and scroll down to the Utilities menu. c. Select Hard Drive Tools. d.
Nonvolatile memory usage Nonvolatile Memory Type HP Sure Start flash (select models only) Amount (Size) Does this memory store customer data? Does this memory retain data when power is removed? 2 MBytes No Yes What is the purpose of this memory? Provides protected backup of critical System BIOS code, EC firmware, and critical PC configuration data for select platforms that support HP Sure Start.
Nonvolatile Memory Type Amount (Size) Does this memory store customer data? Does this memory retain data when power is removed? What is the purpose of this memory? How is data input into this memory? How is this memory write-protected? Downloads, and then follow the on-screen instructions. Intel Management 1.5 MBytes or 5 Engine Firmware MBytes (present in only specific ZBook and EliteBook models. For more information, go to http://www.hp.com/ support, and select your country.
Questions and answers 1. How can the BIOS settings be restored (returned to factory settings)? IMPORTANT: Restore defaults does not securely erase any data on your hard drive. See question and answer 6 for steps to securely erase data. Restore defaults does not reset the Custom Secure Boot keys. See question and answer 7 for information about resetting the keys. 2. a.
IMPORTANT: Resetting will result in the loss of information. These steps will not reset Custom Secure Boot Keys. See question and answer 7 for information about resetting the keys. 7. a. Turn on or restart the computer, and then press esc while the “Press the ESC key for Startup Menu” message is displayed at the bottom of the screen. b. Select Main, and then select Reset BIOS Security to Factory Default. c. Follow the on-screen instructions. d.
18 Power cord set requirements The wide-range input feature of the computer permits it to operate from any line voltage from 100 to 120 volts ac, or from 220 to 240 volts ac. The 3-conductor power cord set included with the computer meets the requirements for use in the country or region where the equipment is purchased. Power cord sets for use in other countries and regions must meet the requirements of the country or region where the computer is used.
Country/region Accredited agency Applicable note number Japan JIS 3 The Netherlands KEMA 1 New Zealand SANZ 1 Norway NEMKO 1 The People's Republic of China CCC 4 Saudi Arabia SASO 7 Singapore PSB 1 South Africa SABS 1 South Korea KTL 5 Sweden SEMKO 1 Switzerland SEV 1 Taiwan BSMI 6 Thailand TISI 1 The United Kingdom ASTA 1 The United States UL 2 1. The flexible cord must be Type HO5VV-F, 3-conductor, 0.75mm2 conductor size.
19 Recycling When a non-rechargeable or rechargeable battery has reached the end of its useful life, do not dispose of the battery in general household waste. Follow the local laws and regulations in your area for battery disposal. HP encourages customers to recycle used electronic hardware, HP original print cartridges, and rechargeable batteries. For more information about recycling programs, see the HP Web site at http://www.hp.com/recycle.
Index A AC adapter, spare part numbers 26 antennas disconnecting 40, 42 audio, product description 2 audio-out (headphone)/audio-in (microphone) combo jack, identifying 7 B backup 115 Backup and Restore 106 backup tools 104 backups 109 creating 105 recovering 106 base enclosure, spare part number 22 battery spare part number 22, 34 battery connector cable removal 64 spare part number 64 battery cover, identifying 15 battery light 7 battery release latch 15 BIOS determining version 81, 86, 93, 97 downloading
removing 36 spare part numbers 22, 25, 36 specifications 121 hard drive hardware kit spare part number 22 Hard Drive Hardware Kit, spare part number 25 hard drive light, identifying 8 hard drive recovery 102, 107 hard drive, identifying 15 HDMI port, identifying 6 heat sink removal 71 spare part number 21, 71 hinge removal 76 HP PC Hardware Diagnostics (UEFI) using 99 HP Recovery Disc Creator, using 104 HP Recovery Manager correcting boot problems 113 starting 112 HP Recovery media creating 109 recovery 112
display panel 1 Ethernet 2 external media cards 3 graphics 1 hard drives 2 keyboard 3 memory module 1 microphone 2 mini card 2 operating system 4 optical drives 2 pointing devices 3 ports 3 power requirements 3 processors 1 product name 1 security 4 serviceability 5 webcam 2 wireless 2 product name 1 product name and number, computer 17 R recover options 111 recovery 103, 115 discs 110, 112 HP Recovery Manager 111 media 112 starting 112 supported discs 110 system 111 USB flash drive 112 using HP Recovery me
USB/audio/card reader board removal 60 spare part number 20, 60 V vents, identifying 7, 15 W webcam 9 product description 2 webcam light, identifying 9 webcam module removal 75 spare part number 23 webcam, identifying 9 Windows Refresh 103 Reset 103 system restore point 109, 110 Windows 7 operating system DVD creating 104 using for restore 107 Windows 7 operating system media creating 104 using for restore 107 Windows application key, identifying 14 Windows key, identifying 13 Windows operating system DVD
