User Guide
© Copyright 2015 HP Development Company, L.P. Bluetooth is a trademark owned by its proprietor and used by Hewlett-Packard Company under license. Intel, Celeron, and Pentium are trademarks of Intel Corporation in the U.S. and other countries. Microsoft and Windows are U.S. registered trademarks of the Microsoft group of companies. For DTS patents, see http://patents.dts.com. Manufactured under license from DTS Licensing Limited.
Safety warning notice WARNING! To reduce the possibility of heat-related injuries or of overheating the computer, do not place the computer directly on your lap or obstruct the computer air vents. Use the computer only on a hard, flat surface. Do not allow another hard surface, such as an adjoining optional printer, or a soft surface, such as pillows or rugs or clothing, to block airflow.
iv Safety warning notice
Processor configuration setting (select models only) IMPORTANT: Select computer models are configured with an Intel® Pentium® N35xx series or a Celeron® N28xx/N29xx series processor and a Windows® operating system. If your computer is configured as described, do not change the processor configuration setting in msconfig.exe from 4 or 2 processors to 1 processor. If you do so, your computer will not restart. You will have to perform a factory reset to restore the original settings.
vi Processor configuration setting (select models only)
Table of contents 1 Welcome ....................................................................................................................................................... 1 Finding information ............................................................................................................................................... 2 2 Getting to know your computer ...................................................................................................................... 3 Right .....
4 Navigating using the keyboard, touch gestures and pointing devices ............................................................... 23 Using pointing devices ......................................................................................................................................... 23 Setting pointing device preferences ................................................................................................. 23 Using the TouchPad and gestures ...........................................
Using battery power .......................................................................................................................... 36 Finding additional battery information .......................................................................... 36 Using Battery Check ........................................................................................................ 37 Displaying the remaining battery charge .......................................................................
Using Disk Cleanup .......................................................................................................... 50 Using HP 3D DriveGuard (select models only) .................................................................................. 50 Identifying HP 3D DriveGuard status .............................................................................. 51 9 Security ............................................................................................................................
Guidelines .......................................................................................................................................... 67 Creating recovery media with HP Recovery Disc Creator ................................................................. 67 Creating recovery media ................................................................................................. 68 Backing up your information ...................................................................................
Appendix A Traveling with or shipping your computer ....................................................................................... 82 Appendix B Troubleshooting ........................................................................................................................... 83 Troubleshooting resources .................................................................................................................................. 83 Resolving issues ......................................
1 Welcome After you set up and register the computer, we recommend the following steps to get the most out of your smart investment: ● Connect to the Internet—Set up your wired or wireless network so that you can connect to the Internet. For more information, see Connecting to a network on page 15. ● Update your antivirus software—Protect your computer from damage caused by viruses. The software is preinstalled on the computer. For more information, see Using antivirus software on page 59.
Finding information You have already used Setup Instructions to turn on the computer and locate this guide. To locate resources that provide product details, how-to information, and more, use this table. Resources For information about Setup Instructions poster ● How to set up the computer ● Help to identify computer components Help and Support ● Operating system information To access Help and Support, select Start > All Programs > HP Help and Support.
2 Getting to know your computer Right Component (1) Description USB 3.0 ports (2) Each USB 3.0 port connects an optional USB device, such as a keyboard, mouse, external drive, printer, scanner or USB hub. NOTE: For details about different types of USB ports, see Using a USB device on page 43. (2) HDMI port Connects an optional video or audio device, such as a highdefinition television, any compatible digital or audio component, or a high-speed HDMI device.
Left Component Description (1) Power connector Connects an AC adapter. (2) Battery light When AC power is connected: ● White: The battery charge is greater than 90 percent. ● Amber: The battery charge is from 0 to 90 percent. ● Off: The battery is not charging. When AC power is disconnected (battery not charging): (3) Vent ● Blinking amber: The battery has reached a low battery level. When the battery has reached a critical battery level, the battery light begins blinking rapidly.
Component Description NOTE: When a device is connected to the jack, the computer speakers are disabled. NOTE: Be sure that the device cable has a 4-conductor connector that supports both audio-out (headphone) and audioin (microphone). (6) Memory card reader Reads optional memory cards that store, manage, share, or access information. (7) Hard drive light ● Blinking white: The hard drive is being accessed. ● Amber: HP 3D DriveGuard has temporarily parked the hard drive.
Display Component Description (1) WLAN antennas (2)* (select products only) Send and receive wireless signals to communicate with wireless local area networks (WLAN). (2) WWAN antennas (2)* (select products only) Send and receive wireless signals to communicate with wireless wide area networks (WWAN). (3) Internal microphones (2) Record sound. (4) Webcam light (select products only) On: The webcam is in use. (5) Webcam (select products only) Records video and captures photographs.
Top TouchPad Component Description (1) TouchPad on/off button Turns the TouchPad on and off. (2) TouchPad zone Moves the pointer and selects or activates items on the screen. NOTE: The TouchPad also supports edge-swipe gestures. For more information, see Edge swipes (select models only) on page 34. (3) Left TouchPad button Functions like the left button on an external mouse. (4) Right TouchPad button Functions like the right button on an external mouse.
Lights Component (1) Description Power light ● On: The computer is on. ● Blinking: The computer is in the Sleep state, a power-saving state. The computer shuts off power to the display and other unneeded components. ● Off: The computer is off or in Hibernation. Hibernation is a power-saving state that uses the least amount of power. NOTE: For select models, the Intel® Rapid Start Technology feature is enabled at the factory.
Component (7) Description TouchPad light ● White: Computer sound is on. ● Amber: The TouchPad is off. ● Off: The TouchPad is on.
Buttons, speakers, and fingerprint reader Component (1) Description Power button ● When the computer is off, press the button to turn on the computer. ● When the computer is on, press the button briefly to initiate Sleep. ● When the computer is in the Sleep state, press the button briefly to exit Sleep. ● When the computer is in Hibernation, press the button briefly to exit Hibernation. CAUTION: Pressing and holding down the power button will result in the loss of unsaved information.
Component Description (4) Volume mute button Mutes and restores speaker sound. (5) Fingerprint reader (select models only) Allows a fingerprint logon to Windows, instead of a password logon.
Keys Component Description (1) esc key Displays system information when pressed in combination with the fn key. (2) fn key Executes frequently used system functions when pressed in combination with a function key, the num lk key, or the esc key. (3) Windows button Displays the Windows Start menu. (4) Function keys Execute frequently used system functions when pressed in combination with the fn key.
Bottom Component Description (1) Battery release latches (2) Release the battery. (2) Battery bay Holds the battery. (3) Vents (3) Enable airflow to cool internal components. NOTE: The computer fan starts up automatically to cool internal components and prevent overheating. It is normal for the internal fan to cycle on and off during routine operation. NOTE: The vents shown in this illustration may vary depending on your computer model.
Component Description CAUTION: To prevent an unresponsive system, replace the wireless module only with a wireless module authorized for use in the computer by the governmental agency that regulates wireless devices in your country or region. If you replace the module and then receive a warning message, remove the module to restore computer functionality, and then contact support. To access Help and Support, select Start > Help and Support.
3 Connecting to a network Your computer can travel with you wherever you go. But even at home, you can explore the globe and access information from millions of websites using your computer and a wired or wireless network connection. This chapter will help you get connected to that world. Connecting to a wireless network Wireless technology transfers data across radio waves instead of wires.
Using HP Connection Manager (select models only) HP Connection Manager provides a central location for managing your wireless devices, an interface for connecting to the Internet using HP Mobile Broadband, and an interface for sending and receiving SMS (text) messages.
● A large-scale WLAN, such as a corporate or public WLAN, typically uses wireless access points that can accommodate a large number of computers and accessories and can separate critical network functions. ● A home or small office WLAN typically uses a wireless router, which allows several wireless and wired computers to share an Internet connection, a printer, and files without requiring additional pieces of hardware or software.
Protecting your WLAN When you set up a WLAN or access an existing WLAN, always enable security features to protect your network from unauthorized access. WLANs in public areas (hotspots) like coffee shops and airports may not provide any security. If you are concerned about the security of your computer in a hotspot, limit your network activities to email that is not confidential and basic Internet surfing.
You may need the HP Mobile Broadband Module serial number to activate mobile broadband service. The serial number is printed on a label on the bottom of your computer. Some mobile network operators require the use of a SIM card. A SIM card contains basic information about you, such as a personal identification number (PIN), as well as network information. Some computers include a SIM card that is preinstalled.
8. Insert the SIM card (1) into the SIM locking hinged connector, and gently push the SIM card until it is firmly seated. Rotate the hinge (2) down to secure the SIM card into the connector. NOTE: The SIM card in your computer may look slightly different from the illustration in this section. NOTE: See the image in the service bay to determine which way the SIM card should be inserted into your computer. 9. Replace the service door. 10. Replace the battery.
Using Bluetooth wireless devices (select models only) A Bluetooth device provides short-range wireless communications that replace the physical cable connections that traditionally link electronic devices such as the following: ● Computers (desktop, notebook, PDA) ● Phones (cellular, cordless, smart phone) ● Imaging devices (printer, camera) ● Audio devices (headset, speakers) ● Mouse Bluetooth devices provide peer-to-peer capability that allows you to set up a personal area network (PAN) of Bluet
2. Plug the other end of the network cable into a network wall jack (2) or router. NOTE: If the network cable contains noise suppression circuitry (3), which prevents interference from TV and radio reception, orient the circuitry end of the cable toward the computer.
4 Navigating using the keyboard, touch gestures and pointing devices Your computer allows navigation using touch gestures (select models only) in addition to the keyboard and mouse. Touch gestures can be used on your computer TouchPad or on a touch screen (select models only). Select computer models have special action key or hot key functions on the keyboard to perform routine tasks.
Tapping To make an on-screen selection, use the Tap function on the TouchPad. ● Tap one finger on the TouchPad zone to make a selection. Double-tap an item to open it. Scrolling Scrolling is useful for moving up, down, or sideways on a page or image. ● 24 Place two fingers slightly apart on the TouchPad zone and then drag them up, down, left, or right.
2-finger pinch zoom 2-finger pinch zoom allows you to zoom out or in on images or text. ● Zoom in by placing two fingers together on the TouchPad zone and then moving your fingers apart. ● Zoom out by placing two fingers apart on the TouchPad zone and then moving your fingers together. 2-finger click 2-finger click allows you to make menu selections for an object on the screen. NOTE: ● Using 2-finger click is the same action as using right-click with the mouse.
Rotating (select models only) Rotating allows you to turn items such as photos. ● Anchor the forefinger of your left hand in the TouchPad zone. Using your right hand, slide your forefinger in a sweeping motion from 12 o’clock to 3 o’clock. To reverse the rotation, move your forefinger from 3 o’clock to 12 o’clock. Flicking (select models only) Flicking allows you to navigate through screens or quickly scroll through documents.
Identifying the hot keys A hot key is a combination of the fn key (1) and either the esc key (2), or one of the function keys (3). To use a hot key: ▲ Briefly press the fn key, and then briefly press the second key of the hot key combination. Hot key combination Description fn+esc Displays system information. fn+f1 Initiates Sleep, which saves your information in system memory. The display and other system components turn off and power is conserved. To exit Sleep, briefly press the power button.
Using the embedded numeric keypad (1) Component Description fn key Turns the embedded numeric keypad on and off when pressed in combination with the num lk key. NOTE: The embedded numeric keypad will not function while an external keyboard or numeric keypad is connected to the computer. (2) Embedded numeric keypad When the keypad is turned on, it can be used like an external numeric keypad. Each key on the keypad performs the function indicated by the icon in the upper-right corner of the key.
● When num lock is on, most keypad keys type numbers. ● When num lock is off, most keypad keys function like the arrow, page up, or page down keys. When num lock on an external keypad is turned on, the num lock light on the computer is turned on. When num lock on an external keypad is turned off, the num lock light on the computer is turned off. To turn num lock on or off on an external keypad as you work: ▲ Press the num lk key on the external keypad, not on the computer.
5 Multimedia Your computer may include the following: ● Integrated speaker(s) ● Integrated microphone(s) ● Integrated webcam ● Preinstalled multimedia software ● Multimedia buttons or keys Audio On your HP computer, you can play music CDs, download and listen to music, stream audio content from the web (including radio), record audio, or mix audio and video to create multimedia. To enhance your listening enjoyment, attach external audio devices such as speakers or headphones.
WARNING! To reduce the risk of personal injury, lower the volume setting before putting on headphones, earbuds, or a headset. For additional safety information, see the Regulatory, Safety and Environmental Notices. To access this guide, select Start > All Programs > HP Help and Support > HP Documentation. Checking audio functions on the computer NOTE: For best results when recording, speak directly into the microphone and record sound in a setting free of background noise.
IMPORTANT: Be sure that the external device is connected to the correct port on the computer, using the correct cable. Check the device manufacturer's instructions if you have questions. NOTE: See Getting to know your computer on page 3 for information about your computer's video ports. VGA The external monitor port, or VGA port, is an analog display interface that connects an external VGA display device such as an external VGA monitor or a VGA projector to the computer. 1.
2. Connect the other end of the cable to the video device 3. Press fn+f4 to alternate the computer screen image between 4 display states: ● PC screen only: View the screen image on the computer only. ● Duplicate: View the screen image simultaneously on both the computer and external device. ● Extend: View the screen image extended across both the computer and external device. ● Second screen only: View the screen image on the external device only.
6 Power management NOTE: A computer may have a power button or a power switch. The term power button is used throughout this guide to mean both types of power controls. Shutting down the computer CAUTION: Unsaved information is lost when the computer shuts down. The shutdown command closes all open programs, including the operating system, and then turns off the display and computer.
NOTE: You cannot initiate any type of networking connection or perform any computer functions while the computer is in the Sleep state. Intel Rapid Start Technology (select models only) For select models, the Intel Rapid Start Technology (RST) feature is enabled by default. Rapid Start Technology allows your computer to resume quickly from inactivity. Rapid Start Technology manages your power-saving options as follows: ● Sleep—Rapid Start Technology allows you to select the Sleep state.
NOTE: If you have set a password to be required on wakeup, you must enter your Windows password before your work will return to the screen. Using the power meter and power settings The power meter is located in the notification area, at the far right of the taskbar. The power meter allows you to quickly access power settings and view the remaining battery charge. ● To reveal the percentage of remaining battery charge and the current power plan, point over the power meter icon.
To access battery information: ▲ Select Start > All Programs > HP Help and Support, and then type battery in the Search box in Help and Support. Using Battery Check Help and Support provides information on the status of the battery installed in the computer. To run Battery Check: 1. Connect the AC adapter to the computer. NOTE: The computer must be connected to external power for Battery Check to work properly. 2.
If the computer is on or in the Sleep state, the computer remains briefly in the Sleep state, and then shuts down and loses any unsaved information.
1. Turn the computer upside down on a flat surface, with the battery bay toward you. 2. Slide the battery release latches (1) to release the battery. NOTE: You can slide the battery release latches simultaneously or you can slide them one at a time. NOTE: Each battery release latch automatically return to its original position. 3. Remove the battery from the computer (2). Conserving battery power ● Select low power-use settings through Power Options in Windows Control Panel.
Disposing of a user-replaceable battery WARNING! To reduce the risk of fire or burns, do not disassemble, crush, or puncture; do not short external contacts; do not dispose of in fire or water. See the Regulatory, Safety and Environmental Notices for proper battery disposal. To access the user guides, select the Start > All Programs > HP Help and Support > HP Documentation.
NOTE: The following instructions apply to computers with user-replaceable batteries. 1. Shut down the computer. 2. Remove the battery on the computer. 3. Connect the AC adapter to the computer, and then plug it into an AC outlet. 4. Turn on the computer. ● If the power lights turn on, the AC adapter is working properly. ● If the power lights remain off, the AC adapter is not functioning and should be replaced. Contact support for information on obtaining a replacement AC power adapter.
7 External cards and devices Using memory card readers Optional memory cards provide secure data storage and convenient data sharing. These cards are often used with digital media–equipped cameras and PDAs as well as with other computers. To determine the memory card formats that are supported on your computer, see Getting to know your computer on page 3. Inserting a memory card CAUTION: To reduce the risk of damage to the memory card connectors, use minimal force to insert a memory card. 1.
3. Press in on the card (1), and then remove it from the slot (2). NOTE: If the card does not eject, pull the card out of the slot. Using a USB device Universal Serial Bus (USB) is a hardware interface that can be used to connect an optional external device, such as a USB keyboard, mouse, drive, printer, scanner, or hub. Some USB devices may require additional support software, which is usually included with the device.
You will hear a sound when the device has been detected. NOTE: The first time you connect a USB device, a message in the notification area lets you know that the device is recognized by the computer. Removing a USB device CAUTION: device. To reduce the risk of damage to a USB connector, do not pull on the cable to remove the USB CAUTION: To reduce the risk of loss of information or an unresponsive system, use the following procedure to safely remove the USB device. 1.
Using optional external drives Removable external drives expand your options for storing and accessing information. A USB drive can be added by connecting the drive to a USB port to the computer. NOTE: HP external USB optical drives should be connected to the powered USB port to the computer. USB drives include the following types: ● 1.
8 Drives Handling drives CAUTION: Drives are fragile computer components that must be handled with care. Refer to the following cautions before handling drives. Do not drop a drive, place items on it, or expose it to liquids, or temperature or humidity extremes. Observe these precautions when handling drives: ● Before removing or installing a drive, shut down the computer. If you are unsure whether the computer is off, in the Sleep state, or in Hibernation, turn the computer on, and then shut it down.
1. Select Start > All Programs > Intel > Intel Rapid Storage Technology. 2. Click the Acceleration link, and then click the Disable Acceleration link. 3. Wait for the Acceleration Mode to complete. 4. Click the Reset to Available link. IMPORTANT: You must temporarily disable SRT when changing RAID modes. Make the change and then reenable SRT. Failure to temporarily disable this feature will prevent you from creating or changing RAID volumes.
1. Tilt down the service door to align the front edge of the service door near the front edge of the computer (1). 2. Slide the service door (2) toward the battery bay until the service door snaps into place. 3. Tighten the service door screw (3) to secure the service door. 4. Insert the screw plug (4). 5. Insert the battery (see Inserting a battery on page 38).
6. Loosen the 4 hard drive screws (1). Pull the hard drive tab (2) toward the side of the computer to disconnect the hard drive. 7. Lift the hard drive (3), and then pull the hard drive out of the hard drive bay. Installing a hard drive NOTE: Your computer may look slightly different from the illustration in this section. To install the hard drive: 1. Insert the hard drive into the hard drive bay at an angle, and then lay the hard drive flat in the hard drive bay (1). 2.
5. Insert the battery (see Inserting a battery on page 38). 6. Connect AC power and external devices to the computer. 7. Turn on the computer. Improving hard drive performance Using Disk Defragmenter As you use your computer over time, the files on the hard drive become fragmented. A fragmented drive means data on your drive is not contiguous (sequential) and, because of this, the hard drive works harder to locate files, thus slowing down the computer.
NOTE: Because solid state drives (SSDs) lack moving parts, they do not require HP 3D DriveGuard protection. NOTE: A hard drive in a primary hard drive bay or a secondary hard drive bay is protected by HP 3D DriveGuard. A hard drive installed in an optional docking device or connected to a USB port is not protected by HP 3D DriveGuard. For more information, see the HP 3D DriveGuard software Help.
9 Security Protecting the computer Standard security features provided by the Windows operating system and the non-Windows Computer Setup utility (BIOS) can protect your personal settings and data from a variety of risks. NOTE: Security solutions are designed to act as deterrents. These deterrents may not prevent a product from being mishandled or stolen. NOTE: Before you send your computer for service, back up and delete confidential files, and remove all password settings.
Using passwords A password is a group of characters that you choose to secure your computer information. Several types of passwords can be set, depending on how you want to control access to your information. Passwords can be set in Windows or in the non-Windows Computer Setup utility that is preinstalled on the computer. ● BIOS administrator and DriveLock passwords are set in Computer Setup and are managed by the system BIOS. ● Automatic DriveLock passwords are enabled in Computer Setup.
Setting passwords in Computer Setup Password Function BIOS administrator password* Protects access to Computer Setup. NOTE: If features have been enabled to prevent removing the BIOS administrator password, you may not be able to remove it until those features have been disabled. DriveLock master password* Protects access to the internal hard drive that is protected by DriveLock. It is also used to remove DriveLock protection. This password is set under DriveLock Passwords during the enable process.
5. When prompted, type your new password once and then again to confirm. 6. To save your changes and exit Computer Setup, select the Exit icon in the lower-right corner of the screen, and then follow the on-screen instructions. – or – Use the arrow keys to select Main > Save Changes and Exit, and then press enter. Your changes go into effect when the computer restarts. Deleting a BIOS administrator password 1.
● The user password and the master password can be identical. ● You can delete a user password or master password only by removing DriveLock protection from the drive. DriveLock protection can be removed from the drive only with the master password. Setting a DriveLock password To set a DriveLock password in Computer Setup, follow these steps: 1. Turn on the computer, and then press esc while the “Press the ESC key for Startup Menu” message is displayed at the bottom of the screen. 2.
Changing a DriveLock password To change a DriveLock password in Computer Setup, follow these steps: 1. Turn on the computer, and then press esc while the “Press the ESC key for Startup Menu” message is displayed at the bottom of the screen. 2. Press f10 to enter Computer Setup. 3. Select BIOS Administrator, and then enter the BIOS Administrator password. 4. Use a pointing device or the arrow keys to select Security > Hard Drive Tools > DriveLock, and then press enter. 5.
9. Clear the DriveLock password on restart check box, and then read the warning. To continue, select OK. 10. To save your changes and exit Computer Setup, select the Exit icon in the lower-right corner of the screen, and then follow the on-screen instructions. – or – Use the arrow keys to select Main > Save Changes and Exit, and then press enter. Your changes go into effect when the computer restarts.
6. Use a pointing device or the arrow keys to select Disable protection. 7. To save your changes and exit Computer Setup, select the Exit icon in the lower-right corner of the screen, and then follow the on-screen instructions. – or – Use the arrow keys to select Main > Save Changes and Exit, and then press enter. Using antivirus software When you use the computer to access e-mail, a network, or the Internet, you potentially expose it to computer viruses.
1. Run Windows Update as soon as possible after you set up your computer. 2. Run Windows Update monthly thereafter. 3. Obtain updates to Windows and other Microsoft programs, as they are released, from the Microsoft website and through the updates link in Help and Support. Using HP Client Security (select models only) HP Client Security software is preinstalled on select computer models. This software can be accessed through Windows Control Panel.
Using the fingerprint reader (select models only) Integrated fingerprint readers are available on select computer models. In order to use the fingerprint reader, you must enroll your fingerprints in HP Client Security. Refer to the HP Client Security software Help. After you enroll your fingerprints, you can use HP Client Security's Password Manager to store and fill in your user names and passwords in supported websites and applications.
10 Maintenance Adding or replacing memory modules The computer has one memory module compartment. The capacity of the computer can be upgraded by adding a memory module to the vacant expansion memory module slot or by upgrading the existing memory module in the primary memory module slot. NOTE: Before adding or replacing a memory module, make sure the computer has the most recent BIOS version, and update the BIOS if needed. See Updating the BIOS on page 73.
b. Grasp the edge of the memory module (2), and then gently pull the memory module out of the memory module slot. CAUTION: To prevent damage to the memory module, hold the memory module by the edges only. Do not touch the components on the memory module. To protect a memory module after removal, place it in an electrostatic-safe container. 6. Insert a new memory module: CAUTION: To prevent damage to the memory module, hold the memory module by the edges only.
c. Gently press the memory module (3) down, applying pressure to both the left and right edges of the memory module, until the retention clips snap into place. CAUTION: module. To prevent damage to the memory module, be sure that you do not bend the memory 7. Replace the service door (see Replacing the service door on page 47). 8. Insert the battery (see Inserting a battery on page 38). 9. Connect AC power and external devices to the computer. 10. Turn on the computer.
CAUTION: Avoid strong cleaning solvents that can permanently damage your computer. If you are not sure that a cleaning product is safe for your computer, check the product contents to make sure that ingredients such as alcohol, acetone, ammonium chloride, methylene chloride, and hydrocarbons are not included in the product. Fibrous materials, such as paper towels, can scratch the computer. Over time, dirt particles and cleaning agents can get trapped in the scratches.
Go to http://www.hp.com/support to download the latest versions of HP programs and drivers. In addition, register to receive automatic update notifications when they become available. Using SoftPaq Download Manager HP SoftPaq Download Manager (SDM) is a tool that provides quick access to SoftPaq information for HP business computers without requiring the SoftPaq number. Using this tool, you can easily search for SoftPaqs, and then download and unpack them.
11 Backup and recovery Your computer includes HP and Windows tools to help you safeguard your information and retrieve it if you ever need to. Your computer does not come with an installed optical drive. To protect your information, use an optional external optical drive. These tools will help you return your computer to a proper working state, all with simple steps.
applications if the hard drive becomes corrupted. HP Recovery Disc Creator can create two kinds of recovery DVDs: ● Windows 7 operating system DVD—Installs the operating system without additional drivers or applications. ● Driver Recovery DVD—Installs specific drivers and applications only, in the same way that the HP Software Setup utility installs drivers and applications. Creating recovery media NOTE: The Windows 7 operating system DVD can be created only once.
To create a backup using Windows Backup and Restore: NOTE: The backup process may take over an hour, depending on file size and the speed of the computer. 1. Select Start > All Programs > Maintenance > Backup and Restore. 2. Follow the on-screen instructions to set up your backup, create a system image (select models only), or create system repair media (select models only).
1. If possible, back up all personal files. 2. If possible, check for the presence of the Windows partition. To check for the Windows partition, select Start > Computer. NOTE: If the Windows partition is not listed, you must recover your operating system and programs using the Windows 7 operating system DVD and the Driver Recovery media. For additional information, see Using Windows 7 operating system media on page 70. 3.
To initiate recovery using a Windows 7 operating system DVD: NOTE: This process takes several minutes. 1. If possible, back up all personal files. 2. Restart the computer, and then insert the Windows 7 operating system DVD into the optical drive before the Windows operating system loads. 3. When prompted, press any keyboard key. 4. Follow the on-screen instructions. 5. Click Next. 6. Select Repair your computer. 7. Follow the on-screen instructions. After the repair is completed: 1.
12 Computer Setup (BIOS), MultiBoot, and HP PC Hardware Diagnostics (UEFI) Using Computer Setup Computer Setup, or Basic Input/Output System (BIOS), controls communication between all the input and output devices on the system (such as disk drives, display, keyboard, mouse, and printer). Computer Setup includes settings for the types of devices installed, the startup sequence of the computer, and the amount of system and extended memory. NOTE: Use extreme care when making changes in Computer Setup.
Use the arrow keys to select Main > Ignore Changes and Exit, and then press enter. ● To save your changes and exit Computer Setup menus: Click the Save icon in the lower-right corner of the screen, and then follow the on-screen instructions. – or – Use the arrow keys to select Main > Save Changes and Exit, and then press enter. Your changes go into effect when the computer restarts. Restoring factory settings in Computer Setup NOTE: Restoring defaults will not change the hard drive mode.
Use the arrow keys to select Main > Ignore Changes and Exit, and then press enter. Downloading a BIOS update CAUTION: To reduce the risk of damage to the computer or an unsuccessful installation, download and install a BIOS update only when the computer is connected to reliable external power using the AC adapter. Do not download or install a BIOS update while the computer is running on battery power, docked in an optional docking device, or connected to an optional power source.
optical drives, diskette drives, a network interface card (NIC), hard drives, and USB devices. Boot devices contain bootable media or files that the computer needs to start and operate properly. NOTE: Some boot devices must be enabled in Computer Setup before they can be included in the boot order. You can change the order in which the computer searches for a boot device by changing the boot order in Computer Setup.
Setting a MultiBoot Express prompt To start Computer Setup and set the computer to display the MultiBoot startup location menu each time the computer is started or restarted, follow these steps: 1. Turn on or restart the computer, and then press esc while the “Press the ESC key for Startup Menu” message is displayed at the bottom of the screen. 2. Press f10 to enter Computer Setup. 3. Use a pointing device or the arrow keys to select System Configuration > Boot Options, and then press enter. 4.
NOTE: To download the HP PC Hardware Diagnostics (UEFI) tool to a USB drive, see Downloading HP PC Hardware Diagnostics (UEFI) to a USB device on page 77. 2. b. Hard drive c. BIOS Use the keyboard arrow keys to select the type of diagnostic test you want to run, and then follow the on-screen instructions. NOTE: If you need to stop a diagnostic test while it is running, press esc.
13 Support Contacting support If the information provided in this user guide or Help and Support does not address your questions, you can contact support. For support, go to http://www.hp.com/support, and select your country. Here you can: ● Chat online with an HP technician. NOTE: When support chat is not available in a particular language, it is available in English. 78 ● Find support telephone numbers. ● Locate an HP service center.
Labels The labels affixed to the computer provide information you may need when you troubleshoot system problems or travel internationally with the computer. IMPORTANT: All labels described in this section will be located in one of 3 places depending on your computer model: affixed to the bottom of the computer, located in the battery bay, or under the service door. ● Service label—Provides important information to identify your computer.
14 Specifications ● Input power ● Operating environment Input power The power information in this section may be helpful if you plan to travel internationally with the computer. The computer operates on DC power, which can be supplied by an AC or a DC power source. The AC power source must be rated at 100–240 V, 50–60 Hz.
15 Accessibility HP designs, produces, and markets products and services that can be used by everyone, including people with disabilities, either on a stand-alone basis or with appropriate assistive devices. Supported assistive technologies HP products support a wide variety of operating system assistive technologies and can be configured to work with additional assistive technologies. Use the Search feature on your device to locate more information about assistive features.
A Traveling with or shipping your computer If you have to travel with or ship your computer, here are some tips to keep in mind to keep your equipment safe. ● Prepare the computer for traveling or shipping: ◦ Back up your information to an external drive. ◦ Remove all discs and all external media cards, such as memory cards, from the computer. ◦ Turn off and then disconnect all external devices. ◦ Shut down the computer. ● Take along a backup of your information.
B Troubleshooting Troubleshooting resources ● Access website links and additional information about the computer through Help and Support. To access Help and Support, select Start > Help and Support. NOTE: Some checkup and repair tools require an Internet connection. HP also provides additional tools that do not require an Internet connection. ● Contact HP support. For U.S. support, go to http://www.hp.com/go/contactHP. For worldwide support, go to http://welcome.hp.com/country/us/en/wwcontact_us.html.
or on both devices simultaneously. When you press fn+f4 repeatedly, the image alternates among the computer display, one or more external displays, and simultaneous display on all devices. Software is functioning abnormally If the software is unresponsive or responds abnormally, restart the computer. Click Start, click the arrow next to Shut down, and then select Restart. If you cannot restart the computer using this procedure, see the next section, The computer is on but not responding on page 84.
device name, and then click Connect. To disable the device, click on the device name, and then click Disconnect. ● Be sure that the wireless device is turned on. ● Be sure that the computer wireless antennas are free from obstructions. ● Be sure that the cable or DSL modem and its power cord are properly connected and that the lights are on. ● Be sure that the wireless router or access point is properly connected to its power adapter and to the cable or DSL modem, and that the lights are on.
The process of burning an optional external optical drive disc does not begin, or it stops before completion 86 ● Be sure that all other programs are closed. ● Turn off Sleep mode. ● Be sure that you are using the right kind of disc for your drive. ● Be sure that the disc is inserted properly. ● Select a slower write speed and try again.
C Electrostatic discharge Electrostatic discharge is the release of static electricity when two objects come into contact—for example, the shock you receive when you walk across the carpet and touch a metal door knob. A discharge of static electricity from fingers or other electrostatic conductors may damage electronic components.
Index Symbols/Numerics 2-finger click TouchPad gestures 25 2-finger pinch zoom TouchPad gesture 25 A AC adapter, testing 40 accessibility 81 administrator password 53 antivirus software 59 audio functions, checking 31 audio-in (microphone) jack, identifying 4 audio-out (headphone) jack, identifying 4 Automatic DriveLock password entering 58 removing 58 B Backup and Restore 69 backup tools 67 backups creating 68 recovering 69 battery conserving power 39 discharging 37 displaying remaining charge 37 disposing
HDMI port, connecting 32 HDMI port, identifying 3 HDMI, configuring audio 33 headphone (audio-out) jack 4 headphones and microphones, connecting 30 Hibernation exiting 35 initiating 35 high-definition devices, connecting 32 hot keys adjusting volume 27 decrease screen brightness 27 decreasing speaker sound 27 description 27 increase screen brightness 27 increasing speaker sound 27 keyboard backlight 27 microphone mute 27 Sleep 27 switching screen image 27 using 27 HP 3D DriveGuard 50 HP Client Security 60 H
R readable media 34 recovery media, creating 67 recovery media, using for restore 70 recovery partition 70 recovery tools 67 recovery tools, Windows 69 recovery, system 69 regulatory information regulatory label 79 wireless certification labels 79 restoring the hard drive 70 RJ-45 (network) jack, identifying 3 RJ-45 (network) lights, identifying 3 rotating TouchPad gesture 26 S screen brightness keys 27 screen image, switching 27 scrolling TouchPad gesture 24 security cable slot, identifying 3 security, wir
