HP Z210 CMT Workstation Maintenance and Service Guide
Table Of Contents
- Product overview
- Setting up the operating system
- Restoring the operating system
- System management
- BIOS ROM
- The Computer Setup (F10) Utility
- Desktop management
- Initial computer configuration and deployment
- Installing a remote system
- Replicating the setup
- Updating and managing software
- HP Client Manager Software
- Altiris Client Management Solutions
- HP SoftPaq Download Manager
- System Software Manager
- ROM Flash
- FailSafe Boot Block ROM
- Workstation security
- Asset tracking
- SATA hard disk drive security
- Password security
- Establishing a setup password using Computer Setup (F10) Utility
- Establishing a power-on password using computer setup
- Entering a power-on password
- Entering a setup password
- Changing a power-on or setup password
- Deleting a power-on or setup password
- National keyboard delimiter characters
- Clearing passwords
- Chassis security
- Fault notification and recovery
- Dual-state power button
- Replacing components
- Warnings and cautions
- Service considerations
- Customer Self-Repair
- Removing and installing components
- Component locations
- Predisassembly procedures
- Disassembly order
- Removing the cable lock (optional)
- Side access panel
- Side access panel sensor (optional)
- Side access panel solenoid lock
- Bezel
- Front panel I/O device assembly
- Optical disk drive (mini-tower configuration)
- Optical disk drive (desktop configuration)
- Speaker
- Power supply
- Power connections
- Rear system fan assembly
- Memory
- Expansion card slot identification
- Expansion card
- Battery
- Hard disk drive
- CPU heatsink
- CPU
- System board
- Converting to desktop configuration
- Product recycling
- Diagnostics and troubleshooting
- Calling technical support
- Locating ID labels
- Locating warranty information
- Diagnosis guidelines
- Troubleshooting checklist
- HP troubleshooting resources and tools
- Troubleshooting scenarios and solutions
- Self-troubleshooting with HP Vision Diagnostics
- Diagnostic codes and errors
- Configuring RAID devices
- Configuring password security and resetting CMOS
- Connector pins
- System board designators
- Routine Care
- Locating HP resources
- Index
ROM Flash ............................................................................................................. 40
Remote ROM Flash ................................................................................... 40
HPQFlash ................................................................................................ 40
FailSafe Boot Block ROM ......................................................................................... 41
Recovering the computer from Boot Block Recovery mode ............................. 41
Workstation security ................................................................................................ 42
Asset tracking .......................................................................................... 42
SATA hard disk drive security .................................................................... 43
DriveLock applications ............................................................... 44
Using DriveLock ........................................................................ 44
Password security ..................................................................................... 46
Establishing a setup password using Computer Setup (F10) Utility ... 46
Establishing a power-on password using computer setup ................ 47
Entering a power-on password .................................................... 47
Entering a setup password ......................................................... 48
Changing a power-on or setup password ..................................... 48
Deleting a power-on or setup password ....................................... 49
National keyboard delimiter characters ....................................... 49
Clearing passwords ................................................................... 50
Chassis security ....................................................................................... 50
Side access panel sensor (Smart Cover Sensor) (optional) .............. 50
Side access panel solenoid lock .................................................. 50
Cable lock (optional) ................................................................. 51
Fault notification and recovery .................................................................................. 51
Drive Protection System ............................................................................. 51
ECC fault prediction ................................................................................. 51
Thermal sensors ....................................................................................... 51
Dual-state power button ........................................................................................... 52
Changing the power button configuration ................................................... 52
5 Replacing components .................................................................................................... 53
Warnings and cautions ........................................................................................................... 54
Service considerations ............................................................................................................ 55
Cautions, warnings and safety precautions ................................................................. 55
ESD information ...................................................................................................... 55
Generating static ...................................................................................... 55
Preventing ESD equipment damage ............................................................ 56
Personal grounding methods and equipment ................................................ 56
Grounding the work area ......................................................................................... 57
Recommended ESD prevention materials and equipment .............................................. 57
Tools and software requirements ............................................................................... 58
ENWW vii










