Getting Started HP Notebook
© Copyright 2011 Hewlett-Packard Development Company, L.P. Bluetooth is a trademark owned by its proprietor and used by Hewlett-Packard Company under license. Microsoft and Windows are U.S. registered trademarks of Microsoft Corporation. SD Logo is a trademark of its proprietor. The information contained herein is subject to change without notice. The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services.
Safety warning notice WARNING! To reduce the possibility of heat-related injuries or of overheating the computer, do not place the computer directly on your lap or obstruct the computer air vents. Use the computer only on a hard, flat surface. Do not allow another hard surface, such as an adjoining optional printer, or a soft surface, such as pillows or rugs or clothing, to block airflow.
iv Safety warning notice
Table of contents 1 Welcome .......................................................................................................................................................... 1 Finding information ............................................................................................................................... 2 2 Getting to know your computer ..................................................................................................................... 4 Top ....................
Using keypads ................................................................................................................... 31 Using the embedded numeric keypad ............................................................... 31 Turning the embedded numeric keypad on and off .......................... 32 Switching key functions on the embedded numeric keypad ............. 32 Using an optional external numeric keypad ...................................................... 32 Using pointing devices ......
Using a Windows 7 operating system DVD (purchased separately) ................. 54 Windows Vista .................................................................................................................................... 55 Backing up your information .............................................................................................. 55 Performing a recovery .......................................................................................................
viii
1 Welcome ● Finding information After you set up and register the computer, it is important to take the following steps: ● Connect to the Internet—Set up your wired or wireless network so that you can connect to the Internet. For more information, refer to Networking on page 22. ● Update your antivirus software—Protect your computer from damage caused by viruses. The software is preinstalled on the computer and includes a limited subscription for free updates.
Finding information The computer comes with several resources to help you perform various tasks. Resources For information about Quick Setup poster ● How to set up the computer ● Help to identify computer components Getting Started guide ● Computer features To access this guide: ● How to connect to a wireless network Select Start > Help and Support > User Guides.
Resources For information about Safety & Comfort Guide ● Proper workstation setup, posture, health, and work habits To access this guide: ● Electrical and mechanical safety information Select Start > Help and Support > User Guides. – or – Select Start > All Programs > HP > HP Documentation. – or – Go to http://www.hp.com/ergo. Worldwide Telephone Numbers booklet HP support telephone numbers This booklet is provided with your computer.
2 Getting to know your computer ● Top ● Front ● Right ● Left ● Display ● Rear ● Bottom Top TouchPad NOTE: 4 Your computer may look slightly different from the illustration in this section.
Component Description (1) Pointing stick (select models only) Moves the pointer and selects or activates items on the screen. (2) Left pointing stick button Can be used with the pointing stick and functions like the left button on an external mouse. (3) TouchPad on/off button Turns the TouchPad on and off. (4) TouchPad Moves the pointer and selects or activates items on the screen. NOTE: Vertical scrolling is supported on the right edge of the TouchPad.
Lights NOTE: Refer to the illustration that most closely matches your computer. Component (1) 6 Description TouchPad on/off light ● Amber: The TouchPad is off. ● Off: The TouchPad is on. (2) Caps lock light On: Caps lock is on. (3) Power light ● On: The computer is on. ● Blinking: The computer is in the Sleep state. ● Off: The computer is off or in Hibernation.
Component (4) (5) Description Wireless light QuickWeb light ● White: An integrated wireless device, such as a wireless local area network (WLAN) device and/or a Bluetooth® device, is on. ● Amber: All wireless devices are off. ● On: The computer is on. ● Off: The computer is off or in Hibernation. NOTE: For more information, refer to “HP QuickWeb” in this guide and to the HP Quickweb software Help (6) (7) Mute light Num lock light ● Amber: Computer sound is off.
Buttons and fingerprint reader NOTE: Refer to the illustration that most closely matches your computer. Component (1) 8 Description TouchPad on/off button Chapter 2 Getting to know your computer Turns the TouchPad on and off.
Component (2) Description Power button ● When the computer is off, press the button to turn on the computer. ● When the computer is on, press the button briefly to initiate Sleep. ● When the computer is in the Sleep state, press the button briefly to exit Sleep. ● When the computer is in Hibernation, press the button briefly to exit Hibernation.
Keys NOTE: Refer to the illustration that most closely matches your computer. Component 10 Description (1) esc key Displays system information when pressed in combination with the fn key. (2) Function keys Execute frequently used system functions when pressed in combination with the fn key.
Component Description (3) fn key Executes frequently used system functions when pressed in combination with a function key, the num lk key, or the esc key. (4) Start key Displays the Start menu. (5) Menu key Displays the active program’s shortcut menu (same as right-click menu). (6) Embedded numeric keypad keys Can be used like the keys on an external numeric keypad when pressed in combination with the fn and num lk keys.
Front NOTE: Component Description (1) Display release latch Opens the computer. (2) Wireless light ● White: An integrated wireless device, such as a wireless local area network (WLAN) device and/or a Bluetooth® device, is on. ● Amber: All wireless devices are off. ● On: The computer is on. ● Blinking: The computer is in the Sleep state. ● Off: The computer is off or in Hibernation. ● Amber: The computer is connected to external power and the battery is charged from 0 – 90%.
Component Description (5) ● Blinking turquoise: The hard drive or optical drive is being accessed. ● Amber: HP 3D DriveGuard has temporarily parked the hard drive. (6) Hard drive light Speaker Produces SRS Premium sound (select models only). NOTE: To use the SRS Premium sound software, select Start > All Programs > SRS Premium Sound.
Right NOTE: Refer to the illustration that most closely matches your computer. Component (1) Description Audio-out (headphone) jack Produces sound when connected to optional powered stereo speakers, headphones, ear buds, a headset, or television audio. NOTE: When a device is connected to the headphone jack, the computer speakers are disabled. (2) Audio-in (microphone) jack Connects an optional computer headset microphone, stereo array microphone, or monaural microphone.
Component (1) Description Audio-out (headphone) jack Produces sound when connected to optional powered stereo speakers, headphones, ear buds, a headset, or television audio. NOTE: When a device is connected to the headphone jack, the computer speakers are disabled. (2) Audio-in (microphone) jack Connects an optional computer headset microphone, stereo array microphone, or monaural microphone.
Left NOTE: Refer to the illustration that most closely matches your computer. Component Description (1) Power connector Connects an AC adapter. (2) 1394 port Connects an optional IEEE 1394 or 1394a device, such as a camcorder. (3) USB or SuperSpeed USB ports (2) Connect optional USB devices. NOTE: Some models support SuperSpeed USB 3.0 technology. These models show a slightly different icon. – or – 16 (4) ExpressCard slot (select models only) Supports optional ExpressCards.
Display NOTE: Refer to the illustration that most closely matches your computer. Component Description (1) Turns off the display or initiates Sleep if the display is closed while the power is on. Internal display switch NOTE: The display switch is not visible from the outside of the computer. (2) WLAN antennas (3)* Send and receive wireless signals to communicate with wireless local area networks (WLAN).
Component Description (9) Used to activate the keyboard light. Keyboard light button *The antennas are not visible from the outside of the computer. For optimal transmission, keep the areas immediately around the antennas free from obstructions. To see wireless regulatory notices, refer to the section of the Regulatory, Safety and Environmental Notices that applies to your country or region. These notices are located in Help and Support.
Rear NOTE: Refer to the illustration that most closely matches your computer. Component Description (1) RJ-11 (modem) jack Connects a modem cable. (2) External monitor port Connects an external VGA monitor or projector. (3) RJ-45 (network) jack Connects a network cable.
Bottom Component (1) Description Vents (3) Enable airflow to cool internal components. NOTE: The computer fan starts up automatically to cool internal components and prevent overheating. It is normal for the internal fan to cycle on and off during routine operation. (2) Battery release latch Releases the battery from the battery bay. (3) Docking connector Connects an optional docking device. (4) Bottom cover release latch Releases or locks the bottom cover.
Component Description (9) Bluetooth compartment Contains a Bluetooth device. (10) Wireless and memory module compartments and hard drive bay Hold an HP Mobile Broadband Module, the memory modules, and the hard drive. NOTE: To prevent an unresponsive system, replace the wireless module only with a wireless module authorized for use in the computer by the governmental agency that regulates wireless devices in your country or region.
3 Networking ● Using an Internet service provider (ISP) ● Connecting to a wireless network NOTE: Internet hardware and software features vary depending on computer model and your location. Your computer may support one or both of the following types of Internet access: 22 ● Wireless—For mobile Internet access, you can use a wireless connection. Refer to Connecting to an existing WLAN on page 24 or Setting up a new WLAN network on page 24.
Using an Internet service provider (ISP) Before you can connect to the Internet, you must establish an ISP account. Contact a local ISP to purchase Internet service and a modem. The ISP will help set up the modem, install a network cable to connect your wireless computer to the modem, and test the Internet service. NOTE: Your ISP will give you a user ID and password to access the Internet. Record this information and store it in a safe place.
Connecting to an existing WLAN 1. Turn on the computer. 2. Be sure that the WLAN device is on. 3. Click the network icon in the notification area, at the far right of the taskbar. 4. Select a network to connect to. 5. Click Connect. 6. If required, enter the security key.
Configuring a wireless router For help in setting up a WLAN, refer to the information provided by your router manufacturer or your ISP. The Windows operating system also provides tools to help you set up a new wireless network. To use the Windows tools to set up your network: ● Windows 7—Select Start > Control Panel > Network and Internet > Network and Sharing Center > Set up a new connection or network > Set up a network. Then follow the on-screen instructions.
4 HP QuickWeb Getting started The HP QuickWeb environment provides a fun and engaging way to perform many of your favorite activities. Your computer is ready to go within seconds of turning it on, allowing you to rapidly access the Internet, widgets, and communication programs. Simply press the QuickWeb button on your computer, and then start browsing the Internet, communicating with Skype, and exploring other HP QuickWeb programs.
Starting HP QuickWeb ● To start HP QuickWeb, press the QuickWeb button when the computer is off or in Hibernation. The following table explains the different behaviors of the QuickWeb button. Button Bahavior QuickWeb button ● When the computer is off or in Hibernation, opens HP QuickWeb. ● When the computer is in Microsoft Windows, opens the default Web browser. ● When the computer is in HP QuickWeb, opens the default Web browser.
5 28 Keyboard and pointing devices ● Using the keyboard ● Using pointing devices Chapter 5 Keyboard and pointing devices
Using the keyboard Identifying the hotkeys NOTE: Refer to the illustration that most closely matches your computer. A hotkey is a combination of the fn key (1) and either the esc key (2) or one of the function keys (3). To use a hotkey: ▲ Briefly press the fn key, and then briefly press the second key of the hotkey combination. Hotkey combination fn+esc Description Displays system information.
Hotkey combination fn+f3 Description Initiates Sleep, which saves your information in system. The display and other system components turn off and power is conserved. To exit Sleep, briefly press the power button. CAUTION: To reduce the risk of information loss, save your work before initiating Sleep. NOTE: If a critical battery level occurs while the computer is in the Sleep state, the computer initiates Hibernation and the information stored in memory is saved to the hard drive.
Using keypads The computer includes an embedded numeric keypad. The computer also supports an optional external numeric keypad or an optional external keyboard that includes a numeric keypad. Using the embedded numeric keypad Component Description (1) fn key Turns the embedded numeric keypad on and off when pressed in combination with the num lk key. (2) Embedded numeric keypad When the keypad is turned on, it can be used like an external numeric keypad.
Turning the embedded numeric keypad on and off Press fn+num lk to turn on the embedded numeric keypad. Press fn+num lk again to turn off the keypad. NOTE: The embedded numeric keypad is turned off while an external keyboard or numeric keypad is connected to the computer.
Using the pointing stick Press the pointing stick in the direction you want to move the pointer on the screen. Use the left and right pointing stick buttons as you would the left and right buttons on an external mouse. Using the TouchPad To move the pointer, slide one finger across the TouchPad in the direction you want the pointer to go. Use the left and right TouchPad buttons like the buttons on an external mouse.
Turning the TouchPad off and on To turn the TouchPad off and on, quickly double-tap the TouchPad on/off light. NOTE: The TouchPad on/off light is off when the TouchPad is on. Navigating To move the pointer, slide one finger across the TouchPad in the direction you want the pointer to go.
Selecting Use the left and right TouchPad buttons like the corresponding buttons on an external mouse. Using TouchPad gestures The TouchPad supports a variety of gestures. To use TouchPad gestures, place two fingers on the TouchPad at the same time. NOTE: TouchPad gestures are not supported in all programs. To view the demonstration of a gesture: 1. Right-click the Synaptics icon in the notification area, at the far right of the taskbar, and then click TouchPad Properties. 2.
Scrolling Scrolling is useful for moving up, down, or sideways on a page or image. To scroll, place two fingers slightly apart on the TouchPad, and then drag them across the TouchPad in an up, down, left, or right motion. NOTE: Scrolling speed is controlled by finger speed. NOTE: Two-finger scrolling is enabled at the factory. Pinching/Zooming Pinching allows you to zoom in or out on images or text. ● Zoom in by placing two fingers together on the TouchPad, and then moving them apart.
Rotating Rotating allows you to rotate items such as photos. To rotate, anchor your left forefinger in the TouchPad zone. Move the right forefinger around the anchored finger in a sweeping motion, moving from 12 o’clock to 3 o’clock. To reverse the rotation, move your right forefinger from 3 o’clock to 12 o’clock. NOTE: Rotating must be done within the TouchPad zone. NOTE: Rotating is disabled at the factory.
6 Maintenance ● Inserting or removing the battery ● Removing or replacing the bottom cover ● Replacing or upgrading the hard drive ● Adding or replacing memory modules ● Updating programs and drivers ● Using SoftPaq Download Manager ● Cleaning your computer Inserting or removing the battery NOTE: For additional information on using the battery, refer to the HP Notebook Reference Guide. To insert the battery: 1.
To remove the battery: CAUTION: Removing a battery that is the sole power source for the computer can cause loss of information. To prevent loss of information, save your work and initiate Hibernation or shut down the computer through Windows before removing the battery. 1. Turn the computer upside down on a flat surface, with the battery bay toward you. 2. Slide the battery release latch (1) to release the battery. 3. Remove the battery from the computer (2).
Removing or replacing the bottom cover CAUTION: To prevent information loss or an unresponsive system: Save your work and shut down the computer before adding or replacing a memory module or hard drive. If you are not sure whether the computer is off or in Hibernation, turn the computer on by pressing the power button. Then shut down the computer through the operating system.
To replace the bottom cover: 1. Tilt down the bottom cover to align the front edge of the bottom cover near the front edge of the computer (1). 2. Insert the alignment tabs (2) on the rear edge of the bottom cover with the notches on the computer. 3. Slide the bottom cover towards the battery bay until the bottom cover snaps into place. 4.
Replacing or upgrading the hard drive CAUTION: To prevent information loss or an unresponsive system: Shut down the computer before removing the hard drive from the hard drive bay. Do not remove the hard drive while the computer is on, in the Sleep state, or in Hibernation. If you are not sure whether the computer is off or in Hibernation, turn the computer on by pressing the power button. Then shut down the computer through the operating system.
9. Use the plastic tab to lift the connector side of the hard drive up at an angle (3) and remove the drive (4) from the computer. To remove the hard drive for the ProBook: 1. Save your work and shut down the computer. 2. Disconnect AC power and external devices connected to the computer. 3. Remove the battery (see Inserting or removing the battery on page 38). 4. Remove the bottom cover (see Removing the bottom cover on page 40). 5. Loosen the 3 hard drive screws (1). 6.
Installing a hard drive To install the hard drive for the EliteBook: 44 1. Insert the hard drive into the hard drive bay at an angle (1), and then lay the hard drive flat in the hard drive bay (2). 2. Pull the plastic tab (3) towards the center of the computer to engage the hard drive with the connector. 3. Tighten the hard drive screws (4). 4. Rotate the SmartCard reader (1) until it lays flat on top the hard drive. 5.
8. Connect AC power and external devices to the computer. 9. Turn on the computer. To install the hard drive for the ProBook: 1. Insert the hard drive into the hard drive bay at an angle (1), and then lay the hard drive flat in the hard drive bay (2). 2. Pull the plastic tab (3) towards the center of the computer to engage the hard drive with the connector. 3. Tighten the hard drive screws (4). 4. Replace the bottom cover (see Replacing the bottom cover on page 40). 5.
CAUTION: To prevent information loss or an unresponsive system: Shut down the computer before adding or replacing memory modules. Do not remove a memory module while the computer is on, in the Sleep state, or in Hibernation. If you are not sure whether the computer is off or in Hibernation, turn the computer on by pressing the power button. Then shut down the computer through the operating system.
6. Insert a new memory module: CAUTION: To prevent damage to the memory module, hold the memory module by the edges only. Do not touch the components on the memory module. a. Align the notched edge (1) of the memory module with the tab in the memory module slot. b. With the memory module at a 45-degree angle from the surface of the memory module compartment, press the module (2) into the memory module slot until it is seated. c.
Using SoftPaq Download Manager HP SoftPaq Download Manager (SDM) is a tool that provides quick access to SoftPaq information for HP business computers without requiring the SoftPaq number. Using this tool, you can easily search for SoftPaqs and then download and unpack them. SoftPaq Download Manager works by reading and downloading, from the HP FTP site, a published database file containing computer model and SoftPaq information.
Cleaning your computer ● Cleaning products ● Cleaning procedures Cleaning products Use the following products to safely clean and disinfect your notebook or tablet PC: ● Dimethyl benzyl ammonium chloride 0.3 percent maximum concentration (For example: germicidal disposable wipes. These wipes come in a variety of brand names.
Cleaning the TouchPad and keyboard CAUTION: When cleaning the TouchPad and keyboard, do not let liquids drip between the keys. This can permanently damage internal components. ● To clean and disinfect the TouchPad and keyboard, use a soft microfiber cloth or chamois moistened with one of the cleaning solutions listed previously or use an acceptable germicidal disposable wipe.
7 Backup and recovery Windows 7 ● Backing up your information ● Performing a system recovery To protect your information, use Windows Backup and Restore to back up individual files and folders, back up your entire hard drive (select models only), create system repair discs (select models only) by using the installed optical drive (select models only) or an optional external optical drive, or create system restore points.
new software and data files, you should continue to back up your system on a regular basis to maintain a reasonably current backup. The system repair discs (select models only) are used to start up (boot) the computer and repair the operating system in case of system instability or failure. Your initial and subsequent backups allow you to restore your data and settings if a failure occurs. You can back up your information to an optional external hard drive, a network drive, or discs.
Using the Windows recovery tools To recover information you previously backed up: 1. Select Start > All Programs > Maintenance > Backup and Restore. 2. Follow the on-screen instructions to recover your system settings, your computer (select models only), or your files. To recover your information using Startup Repair, follow these steps: CAUTION: Using Startup Repair completely erases hard drive contents and reformats the hard drive.
3. If the HP Recovery partition is listed, restart the computer, and then press esc while the “Press the ESC key for Startup Menu” message is displayed at the bottom of the screen. 4. Press f11 while the “Press for recovery” message is displayed on the screen. 5. Follow the on-screen instructions. Using a Windows 7 operating system DVD (purchased separately) To order a Windows 7 operating system DVD, go to http://www.hp.
Windows Vista To protect your information, use the Backup and Restore Center to back up individual files and folders, back up your entire hard drive (select models only), or create system restore points. In case of system failure, you can use the backup files to restore the contents of your computer.
To create a backup using Backup and Restore Center: NOTE: Be sure that the computer is connected to AC power before you start the backup process. NOTE: The backup process may take over an hour, depending on file size and the speed of the computer. 1. Select Start > All Programs > Maintenance > Backup and Restore Center. 2. Follow the on-screen instructions to back up your entire computer (select models only) or your files.
4. Select Repair your computer. 5. Follow the on-screen instructions. NOTE: For additional information on recovering information using the Windows tools, perform a search for these topics in Help and Support. Using f11 recovery tools CAUTION: Using f11 completely erases hard drive contents and reformats the hard drive. All files you have created and any software installed on the computer are permanently removed.
Using a Windows Vista operating system DVD (purchased separately) To order a Windows Vista operating system DVD, go to http://www.hp.com/support, select your country or region, and follow the on-screen instructions. You can also order the DVD by calling technical support. For contact information, refer to the Worldwide Telephone Numbers booklet included with the computer. CAUTION: Using a Windows Vista operating system DVD completely erases hard drive contents and reformats the hard drive.
8 Customer support ● Contacting customer support ● Labels 59
Contacting customer support If the information provided in this user guide, in the HP Notebook Reference Guide, or in Help and Support does not address your questions, you can contact HP Customer Support at: http://www.hp.com/go/contactHP NOTE: For worldwide support, click Contact HP worldwide on the left side of the page, or go to http://welcome.hp.com/country/us/en/wwcontact_us.html. Here you can: ● Chat online with an HP technician.
Labels The labels affixed to the computer provide information you may need when you troubleshoot system problems or travel internationally with the computer: ● Serial number label—Provides important information, including the following: Component (1) Product name (2) Serial number (s/n) (3) Part number/Product number (p/n) (4) Warranty period (5) Model description Have this information available when you contact technical support. The serial number label is affixed to the bottom of the computer.
9 62 Specifications ● Input power ● Operating environment Chapter 9 Specifications
Input power The power information in this section may be helpful if you plan to travel internationally with the computer. The computer operates on DC power, which can be supplied by an AC or a DC power source. The AC power source must be rated at 100–240 V, 50–60 Hz. Although the computer can be powered from a standalone DC power source, it should be powered only with an AC adapter or a DC power source supplied and approved by HP for use with this computer.
Operating environment Factor Metric U.S.
Index Symbols/Numerics 1394 port, identifying 16 A accessory battery connector, identifying 20 ambient light sensor, identifying 17 ambient light, hotkey 30 audio-in (microphone) jack 14, 15 audio-out (headphone) jack 14, 15 B Backup and Restore 52 Backup and Restore Center 55, 56 battery bay 20, 61 battery light 12 battery release latch 20 battery, replacing 38 Bluetooth compartment, identifying 21 Bluetooth label 61 Bottom cover release latch, identifying 20 bottom cover, removing or replacing 40 butto
K keyboard hotkeys, identifying 29 keypad, embedded numeric 11 keypad, external num lock 32 using 32 keypads, identifying 31 keys esc 10 fn 11, 31 function 10 menu 11 num lk 11 start 11 menu key, identifying 11 Microsoft Certificate of Authenticity label 61 Mobile Broadband Module, identifying 21 mouse, external setting preferences 32 mute light, identifying 7 L labels Bluetooth 61 HP Mobile Broadband Module 61 Microsoft Certificate of Authenticity 61 regulatory 61 serial number 61 SIM 61 wireless certifi
W webcam 17, 18 webcam light, identifying 17, 18 webcam, identifying 17, 18 Windows 7 operating system DVD 54 Windows Backup and Restore 51 Windows Vista operating system DVD 58 wireless antennas, identifying 17, 18 wireless button, identifying 9 wireless certification label 61 wireless lights 7, 12 wireless network (WLAN), equipment needed 24 wireless network, connecting 23 wireless router, configuring 25 wireless set up 24 wireless, identifying 21 WLAN connecting 24 protecting 25 WLAN antennas, identifyin
