User's Manual

1
Regulatory notices
This document provides country- and region-specific non-wireless and wireless regulatory notices and compliance information for the product. Some of these notices may
not apply to your product.
㢨Gⱬ㉐⏈G㡔㉔GⵃGⱨ㉔G㥐䖼Ḵ⥜G䚐ạGἐ󰵾Ḵ⥜═Gḩ㫴⪰Gᵍ㢨G䔠䚜䚌ḔG㢼㏩⏼␘ . 㥐䖼㢌G䏭㉥㜄G♤
⢰G㢰⺴Gḩ㫴⏈G䚨␭G㥐䖼㜄G㤵㟝╌㫴G㙾㡸G㍌G㢼㏩⏼␘ .
One or more integrated wireless devices may be installed. In some environments, the use of wireless devices may be restricted. Such res
trictions may apply on-board
airplanes, in hospitals, near explosives, in hazardous locations, and so on. If you are uncertain of the policy that applies to the use of this product, ask for authorization to
use it before you turn it on.
Regulatory markings for your country or region may be located on the bottom of the product. The FCC has granted an Equipment Authorization for this model device with
all reported SAR levels evaluated as in compliance with the FCC RF exposure guidelines. SAR information on this model is on file with the FCC and can be found under the
Display Grant section of http://www.fcc.gov/oet/ea/fccid.
Federal Communications Commission notice
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not
occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the following measures:
 Reorient or relocate the receiving antenna.
 Increase the separation between the equipment and receiver.
 Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
 Consult the dealer or an experienced radio or television technician for help.
Modifications
The FCC requires the user to be notified that any changes or modifications made to this device that are not expressly approved by HP may void the user's authority to
operate the equipment.
Cables
To maintain compliance with FCC Rules and Regulations, connections to this device must be made with shielded cables having metallic RFI/EMI connector hoods.
Declaration of Conformity for products marked with the FCC logo (United States only)
This device complies with Part 15 of the FCC Rules. Operation is subject to the following 2 conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause undesired operation.
For further information, contact:
Manager of Corporate Product Regulations
Hewlett-Packard Company
3000 Hanover Street
Palo Alto, CA 94304
[phone]
To identify your product, refer to the part, series, or model number located on the product.
Products with wireless LAN devices or HP Mobile Broadband Modules
This device must not be co-located or operating in conjunction with any other antenna or transmitter.
w
WARNING: Exposure to Radio Frequency Radiation The radiated output power of this device is below the FCC radio frequency exposure
limits. Nevertheless, the device should be used in such a manner that the potential for human contact is minimized during normal
operation.
The exposure standard for wireless devices employs a unit of measurement known as the Specific Absorption Rate, or SAR. The SAR limit
set by the FCC is 1.6 W/Kg. Tests for SAR are conducted using standard operating positions accepted by the FCC with the device transmitting
at its highest certified power level in all tested frequency bands. Although the SAR is determined at the highest certified power level, the
actual SAR level of the device while operating can be well below the maximum value. This is because the device is designed to operate at
multiple power levels so as to use only the power required to reach the network. In general, the closer you are to a wireless base station
antenna, the lower the power output. To avoid the possibility of exceeding the FCC radio frequency exposure limits, human proximity to the
antenna should be minimized. This device has been tested and demonstrated compliance when Bluetooth and WiFi are transmitting
simultaneously.
w
CAUTION: When using IEEE 802.11a wireless LAN, this product is restricted to indoor use, due to its operation in the 5.15- to 5.25-GHz
frequency range. The FCC requires this product to be used indoors for the frequency range of 5.15 GHz to 5.25 GHz to reduce the potential
for harmful interference to co-channel mobile satellite systems. High-power radar is allocated as the primary user of the 5.25- to 5.35-GHz
and 5.65- to 5.85-GHz bands. These radar stations can cause interference with and/or damage to this device.
Brazil notice
Este equipamento opera em caráter secundário, isto é, não tem direito a proteção contra interferência prejudicial, mesmo de estações do mesmo tipo, e não pode causar
interferência a sistemas operando em caráter primário.
Este equipamento atende aos limites de Taxa de Absorção Específica referente à exposição a campos elétricos, magnéticos e eletromagnéticos de radiofreqüências
adotados pela ANATEL.
Regs_Tablet.book Page 1 Friday, August 16, 2013 5:52 PM