Quick Start Guide A7000 dl 8xT1/E1 Wide Module (J8463A) 2006-05

ManualsBrandsHP ManualsComputer AccessoriesHP 1-port ADSL2 + Annex A dl Module

Quick Start Guide 5991-2111

ProCurve Secure Router dl 8xT1/E1 Wide Module

J8463A

XT1/E1 WIDE MODULE COMMON COMMANDS

clock source [line* | internal]

Configures the source timing used for the interface.

line* Recovers clock from the T1/E1 circuit.

internal Provides clocking using the internal oscillator.

loopback network [line | payload]

Initiates a loopback on the interface toward the network. Use the no form of this command to deactivate the

loopback.

line Initiates a metallic loopback of the physical T1/E1 network interface.

payload Initiates a loopback of the T1/E1 framer (CSU portion) of the T1/E1 network interface.

remote-loopback

Configures the T1/E1 interface to respond to loopbacks initiated by a remote unit (or service provider). Use the no

form of this command to disable this feature.

shutdown

Disables the interface (both physical and virtual) so that no data will pass through. Use the no form of this

command to turn on the interface and allow it to pass data. By default, all interfaces are disabled.

show test-pattern

Displays the results (including error count) from active test patterns.

snmp trap link-status

Controls the SNMP variable, ifLinkUpDownTrapEnable (RFC2863) to enable the interface to send SNMP traps

when there is an interface status change. Use the no form of this command to disable this trap.

Activates the built-in pattern generator and begins sending the specified test pattern. Can be used to verify a data

path when used in conjunction with an active loopback. Use the no form of this command to cease pattern

generation.

clear Clears the test pattern error count. Display the error count using the

show test-pattern command.

insert Inserts an error into currently active test pattern. Display the injected error result using

the show test-pattern command.

ones Generates a pattern of continuous ones.

p215 Generates a pseudorandom test pattern sequence based on a 15-bit shift register.

p511 Generates a repeating pattern of ones and zeros.

qrss Generates a random pattern of ones and zeros.

zeros Generates a pattern of continuous zeros.

tdm-group <group#> timeslot <DS0 range> speed [64]

Creates a group of contiguous DS0s on this interface to be used during the bind process.

<group#> Number label (1 to 255) to identify this TDM group.

<DS0 range> Specifies the timeslots used in the TDM group. Enter as a single number (representing

one of 24 T1 or 31 E1 channel timeslots) or as a contiguous group of channels. (For

example, 1-10 specifies the first ten channels of the T1 or E1 circuit.)

64 (Optional) Specifies a DS0 rate of 64 kbps.

8XT1/E1 WIDE MODULE T1 COMMANDS

coding [ami | b8zs*]

Configures the line coding for the T1 physical interface. This setting must match the line coding supplied on the

circuit by the service provider (or external equipment).

ami Specifies alternate mark inversion.

b8zs* Specifies bipolar eight zero substitution.

fdl [ansi* | att | none]

Specifies the format of the facility data link (FDL) channel on the T1 circuit.

ansi* Configures the FDL for ANSI T1.403.

att Configures the FDL for ATT TR 54016.

none No FDL standard specified.

framing [d4 | esf*]

Configures the framing format of the T1 interface.

d4 Specifies D4 superframe (SF) T1 framing.

esf* Specifies Extended SF T1 framing.

lbo [long <0

| -7.5 | -15 | -22.5> | short <0 to 655>]

Sets the line build out (in dB or feet) for the T1 Interface. Use the lbo long command for T1 interfaces with a cable

length greater than 655 feet. Use the lbo short command for T1 interfaces with a cable length less than 655 feet.

loopback remote line [fdl | inband]

Sends loopback code to the remote unit to initiate a line loopback. Use the no form of this command to send a

loopdown code to the remote unit to deactivate the loopback.

fdl Uses the facility data link (FDL) to initiate a full 1.544 Mbps physical loopback (metallic

loopback) of the signal received by the remote unit from the network.

inband Uses the inband channel to initiate a full 1.544 Mbps physical loopback (metallic

loopback) of the signal received by the remote unit from the network.

loopback remote payload

Sends loopback code to the remote unit to initiate a payload loopback at the far end. A payload loopback is a

1.536 Mbps loopback of the payload data received from the network maintaining bit-sequence integrity for the

information bits by synchronizing (regenerating) the timing. Use the no form of this command to send a loopdown

code to the remote unit to deactivate the loopback.

remote-alarm rai

Selects the alarm signaling type to be sent when a loss of frame is detected on the T1 receive signal. Use the no

form of this command to disable all transmitted alarms.

rai* Sends a remote alarm indication (RAI) in response to a loss of frame. Also prevents a

received RAI from causing a change in interface operational status.

8XT1/E1 WIDE MODULE E1 COMMANDS

coding [ami | hdb3*]

Configures the line coding for the E1 physical interface. The settings must match the line coding supplied on the

circuit by the service provider.

ami Configures the line coding for alternate mark inversion.

hdb3

Configures the line coding for high-density bipolar 3.

framing [crc4]

Configures the framing format of the E1 interface. This setting must match the framing format provided by the

service provider (or external equipment).

crc4 Enables CRC4 framing.

loop-alarm-detect

Enables detection of a loop alarms on the E1 interface. Use the no form of this command to disable loop alarm

detection. This setting is enabled by default.

remote-alarm [rai* | ais]

Selects the alarm signaling type to be sent when a loss of frame is detected on the E1 receive signal. Use the no

form of this command to disable all transmitted alarms.

rai* Sends a remote alarm indication (RAI) in response to a loss of frame. Also prevents a

received RAI from causing a change in interface operational status.

ais Sends an alarm indication signal (AIS) as an unframed all-ones signal.

ts16

Enables timeslot 16 multiframe to be checked on the receive signal. Use the no form of this command to disable

timeslot 16.

* Indicates the default value.

Note

This command list is an illustration of available commands. For complete

command descriptions and default values, refer to the SROS Command Line

Interface Reference Guide provided on your ProCurve SROS Documentation

CD.