HP 10Gb Ethernet BL-c Switch Browser-based Interface Reference Guide Part number: 445945-001 First edition: June 2007
Legal notices © 2007 Hewlett-Packard Development Company, L.P. The information contained herein is subject to change without notice. The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty. HP shall not be liable for technical or editorial errors or omissions contained herein. Microsoft®, Windows®, and Windows NT® are U.S.
Contents Contents Getting started Introduction ........................................................................................................................................... 8 Additional references ............................................................................................................................. 8 Features................................................................................................................................................ 8 Requirements.....
Contents RMON History Group Information.......................................................................................................... 47 RMON Alarm Group Information ........................................................................................................... 48 RMON Event Group Information ............................................................................................................ 50 IP Interfaces Dashboard ..........................................................
Contents CPU Utilization .................................................................................................................................... 96 FDB Statistics ....................................................................................................................................... 97 Network Time Protocol Statistics............................................................................................................. 98 Switch Ports Statistics Summary.....................
Contents Configuration ............................................................................................................................... 162 Switch Image and Configuration Management controls...................................................................... 162 Switch Image and Configuration Management buttons....................................................................... 164 Management Network Definition Configuration ...............................................................
Contents IGMP Filters Configuration ............................................................................................................. 217 IGMP Filter Configuration............................................................................................................... 218 IGMP Filtering Port Configuration .................................................................................................... 219 IGMP Filtering - Port Configuration ..............................................
Getting started Getting started Introduction The HP 10Gb Ethernet BL-c Switch software lets you use your Web browser to access switch information and statistics and perform switch configuration via the Internet. This guide provides a reference to the browser-based interface (BBI) for the HP 10GbE switch. This chapter briefly describes the software features and requirements for the BBI and explains how to access the BBI start page.
Getting started Switch setup Before you can access the BBI, minimal configuration is required on the switch. Configuring IP interfaces At least one IP interface must be configured on the switch. This is usually done from the command line interface during first-time switch set up. Each IP interface address provides a point of access for switch management.
Getting started Starting the BBI When the switch and browser setup is complete, follow these steps to launch the BBI: 1. Start your Web browser. 2. Enter the switch IP interface address in the Web browser Uniform Resource Locator (URL) field. For example, if the switch IP interface has a network IP address of 12.20.7.132, using Mozilla Firefox, you could enter the following (for secure BBI access, use https://).
Getting started 3. Log in to the switch. If your switch and browser are properly configured, you will be asked to enter a password. Enter the account name and password for the switch. For more password information, see the HP 10Gb Ethernet BL-c Switch Command Reference.
Getting started 4. Allow the BBI Dashboard page to load. When the proper account name and password combination is entered, the BBI Dashboard page is displayed in the browser viewing area. NOTE: There may be a slight delay while the Dashboard page is initializing. You should not stop the browser while loading is in progress. When loading is complete, a folder icon for the switch displays in the left-hand BBI window. Click this folder and a tree of folders displays.
Browser-based interface basics Browser-based interface basics Introduction Once you are properly logged in, the switch BBI displays in the Web browser-viewing window. There are three main regions on the screen. • • • The Toolbar is used for selecting the context for your actions in the other windows. The Navigation window is used for selecting particular items or features to act upon. The Forms window is used for viewing or altering switch information.
Browser-based interface basics Toolbar The toolbar contains buttons and commands used to access and execute switch functions. Context buttons The context buttons on the toolbar is used for setting the context for your actions in the application: Table 1 Context buttons Button Description Configure When selected, you can access and alter the switch configuration forms. Select an item in the navigation window to display the desired configuration form in the forms window.
Browser-based interface basics Navigation window The navigation window is used for selecting a particular switch feature to act upon. Status, statistics, or configuration forms for the selected item will display in the forms window, depending on the context chosen on the toolbar. The navigation window contains a tree of folders, subfolders, and feature icons. Click any closed folder to open it and reveal its contents. Click any open folder to close it.
Dashboard Dashboard Introduction The switch BBI can be used to view the present settings and operating status of a variety of switch features. Most of the same information available through the switch’s command line interface is present on the dashboard forms. The following provides a basic outline for viewing the dashboard forms. You should first be familiar with configuration as covered in the HP 10Gb Ethernet BL-c Switch Command Reference.
Dashboard 3. View information shown in the forms window. NOTE: Items that load other forms when selected are underlined. 4. Select an underlined item to view details or perform actions.
Dashboard In this example, click a Spanning Tree Group number to view detailed information about the group (shown in form below).
Dashboard Switch Dashboard To display the following form, select System > General. This is the default form for the switch. The following table describes the Switch Dashboard controls: Table 3 Switch Dashboard controls Control Description Switch Name Displays the name of the switch, as entered in Configuration > Switch > General (SNMP). Switch Location Displays the location of the switch, as entered in Configuration > Switch > General (SNMP). Switch Type Displays the type of switch.
Dashboard Table 3 Switch Dashboard controls Control Description Time and date Displays the current time and date. Timezone Location Displays the time zone where the switch resides. You are prompted to select your location (continent, country, region) by the timezone wizard. Once a region is selected, the switch updates the time to reflect local changes to Daylight Savings Time, etc. Daylight Savings Time Displays the status (enabled or disabled) of daylight savings time in the system clock.
Dashboard User Access Dashboard To display the following form, select System > User Table. The following table describes the User Access Dashboard controls: Table 4 User Access Dashboard controls Control Description User ID Displays the numeric identifier for the user User Name Displays the name of the user. COS Displays the Class of Service level for the user. Password Indicates whether a valid password is defined for the user. Status Displays whether the user is enabled or disabled.
Dashboard RADIUS Dashboard To display the following form, select System > Radius. The following table describes the switch RADIUS Dashboard controls: Table 5 RADIUS Dashboard controls Control Description Primary Radius IP Address Displays the primary RADIUS server address. Secondary Radius IP Address Displays the secondary RADIUS server address. Current RADIUS server Displays the current RADIUS server address. Radius port Displays the number of the User Datagram Protocol (UDP) port for RADIUS.
Dashboard Table 5 RADIUS Dashboard controls Control Description Secondary Radius Server Secret Displays the secondary shared secret between the switch and the RADIUS server(s).
Dashboard TACACS+ Dashboard To display the following form, select System > Tacacs+. The following table describes the switch TACACS+ Dashboard controls: Table 6 TACACS+ Dashboard controls Control Description Primary Tacacs+ IP Address Displays the primary TACACS+ server address. Secondary Tacacs+ IP Address Displays the secondary TACACS+ server address. Tacacs+ port Displays the number of the TCP port for TACACS+.
Dashboard Table 6 TACACS+ Dashboard controls Control Description Tacacs+ Backdoor for Telnet/ ssh/http/https Displays the status of the TACACS+ back door for telnet. The telnet command also applies to SSH/SCP connections and the Browserbased Interface (BBI). This command does not apply when secure backdoor (secbd) is enabled. Tacacs+ Secure Backdoor for telnet/ ssh/http/https Displays the status of the TACACS+ back door using secure password for telnet/SSH/ HTTP/HTTPS.
Dashboard NTP Dashboard To display the following form, select System > NTP. The following table describes the Network Time Protocol Dashboard controls: Table 7 NTP Dashboard controls Control Description NTP Server IP Address Displays the IP address of the active NTP server. Transfer port of Primary Server Displays the type of port used for data transfer between the switch and the primary NTP server.
Dashboard Switch Image and Configuration Management Dashboard To display the following form, select System > Config/Image Control. The following table describes the Switch Image and Configuration Dashboard controls: Table 8 Switch Image and Configuration Dashboard controls Control Description Active Image Version Displays the number of the active software image. Next Boot Image Selection Displays which software image (image1 or image2) will be loaded into switch memory for the next reboot.
Dashboard Management Network Definition Dashboard To display the following form, select System > Management Network. The following table describes the Management Network Definition Dashboard controls: Table 9 Management Network Definition Dashboard controls Control Description Entry Displays the entry number for each management network. Management Network Displays the IP address of the management network. Management Network Subnet Mask Displays the subnet mask of the management network.
Dashboard SFP Information To display the following form, select System > SFP. The following table describes the status of each Small Form Pluggable (SFP or XFP) module on each fiber external port. Table 10 SFP Information Control Description Port Displays the port number and SFP/XFP number.
Dashboard Switch Ports Dashboard To display the following form, select Switch Ports (click the underlined text, not the folder).
Dashboard Table 11 Switch Ports Dashboard controls Control Description Speed/Duplex/Flow Ctl Displays parameters for the port link. Input Frames/Output Frames Displays the number of frames that have been received by this port (Input Frames) and the number of frames that have been transmitted by this port (Output Frames). Link State Changes/Total Errors Displays the total number of link state changes for this port and the total number of errors logged by this port.
Dashboard Switch Ports 802.1x Dashboard To display the following form, select Layer 2 > 802.1x > Switch Ports. The following table describes the Switch Ports 802.1x Dashboard fields: Table 13 Switch Ports 802.1x Dashboard Field Description Port Displays each port’s name. Auth Mode Displays the Access Control authorization mode for the port.
Dashboard Table 13 Switch Ports 802.1x Dashboard Field Description Authenticator PAE State Displays the Authenticator Port Access Entity State. The PAE state can be one of the following: • • • • • • • • Backend Auth State initialize disconnected connecting authenticating authenticated aborting held forceAuth Displays the Backend Authentication State. The Backend Authentication state can be one of the following: • • • • • • request response success fail timeout idle Port 802.
Dashboard The following table describes the Port 802.1x Dashboard controls: Table 14 Port 802.1x Dashboard controls Control Description Authentication Mode Displays the Access Control authorization mode for the port. The Authorization mode can be one of the following: • force-unauth • auto • force-auth Authentication Status Displays the current authorization status of the port, either authorized or unauthorized.
Dashboard Forwarding Database Information To display the following form, select Layer 2 > FDB. The forwarding database (FDB) contains information that maps the media access control (MAC) address of each known device to the switch port where the device address was learned. The FDB also shows which other ports have seen frames destined for a particular MAC address. NOTE: The master forwarding database supports up to 8K MAC address entries on the MP per switch.
Dashboard Table 15 Forwarding Database Information controls Control Description VLAN Displays the VLAN number of the FDB entry. Source Port Displays the source port of the FDB entry. Trunk Displays the trunk number of the FDB entry, if applicable. State Displays the port state of the FDB entry. Learned Port Displays the port number of the port that received the FDB entry. Permanent Displays whether the FDB entry is a static, permanent entry.
Dashboard The following table describes the VLANs Dashboard controls: Table 16 VLANs Dashboard controls Control Description Search Range To search for a VLAN, enter a range of VLAN numbers in the From and To fields. Search Options To focus the search for a VLAN, enter optional search parameters: • VLAN Name • VLAN State Fields that have a value of “any” are ignored during the search. Choose a search operation: • or: Search for VLANS specified in the search range that meet any of the criteria entered.
Dashboard Switch Spanning Tree Groups Information To display the following form, select Layer 2 > Spanning Tree Groups (click the underlined text, not the folder). The following table describes the Switch Spanning Tree Groups Information controls: Table 17 Switch Spanning Tree Groups Information controls Control Description Search Range To search for a Spanning Tree Group, enter a range of group numbers in the From and To fields.
Dashboard Table 17 Switch Spanning Tree Groups Information controls Control Description Search Options To focus the search for a Spanning Tree Group, enter optional search parameters: • Bridge Priority • Spanning Tree State Fields that have a value of “any” are ignored during the search. Choose a search operation: • or: Search for spanning tree groups specified in the search range that meet any of the criteria entered.
Dashboard Switch Spanning Tree Group Information To display the following form, go to the Switch Spanning Tree Groups Information form. Select a Spanning Tree Group number. The following table describes the Switch Spanning Tree Group Information controls: Table 18 Switch Spanning Tree Group Information controls Control Description Spanning Tree State Shows if Spanning Tree is turned on or off for the switch. VLANs Displays the VLANs that are members of this Spanning Tree Group.
Dashboard Table 18 Switch Spanning Tree Group Information controls Control Description Path Cost Displays the cumulative path cost to the Current Root. Root Port Displays the switch port that is connected to the Current Root. Max Age Specifies, in seconds, the maximum time the bridge waits without receiving a configuration bridge protocol data unit before it reconfigures the STP network. If the bridge is not the root bridge, it uses the MaxAge value of the root bridge.
Dashboard Table 19 Switch Spanning Tree Port Information controls Control Description Port Priority Helps determine which bridge port becomes the designated port. In a network topology that has multiple bridge ports connected to a single segment, the port with the lowest port priority becomes the designated port for the segment. Port Cost Helps determine the designated port for a segment. Generally speaking, the faster the port, the lower the path cost.
Dashboard The following table describes the Switch Trunk Groups Dashboard controls: Table 20 Switch Trunk Groups Dashboard controls Control Description Status For each port in the Trunk Group, shows whether the port is down (red), up and forwarding (green) or in blocking state. Trunk Group Displays the numeric identifier of the Trunk Group. Switch Port Displays the port number of each port that is a member of the Trunk Group. STG Displays the Spanning Tree Group to which this trunk belongs.
Dashboard LACP Dashboard To display the following form, select Layer 2 > LACP. The following table describes the Switch LACP Dashboard controls: Table 22 LACP Dashboard controls Control Description Switch Port Displays the port number. LACP Mode Displays the port’s LACP mode (active, passive, or off). LACP Adminkey Displays the value of the port’s adminkey. LACP Operkey Displays the value of the port’s operkey.
Dashboard LACP Port Dashboard To display the following form, go to the Switch LACP Dashboard. Select a port number. This form summarizes LACP port information.
Dashboard Uplink Fast General Information To display the following form, select Layer 2 > Uplink Fast. The following table describes the Uplink Fast Information controls: Table 23 Uplink Fast General Information controls Control Description STP Uplink Fast Mode Displays the status of STP Uplink Fast: ON or OFF. STP Uplink Fast Rate Displays the value of the Uplink Fast station update rate, in seconds.
Dashboard RMON History Group Information To display the following form, select RMON > History (click the underlined text, not the folder). This form displays information for all configured RMON History Groups. The following table describes the RMON History Group Dashboard controls: Table 24 RMON History Group Dashboard controls Control Description Search Range To search for a History Group, enter a range of numbers in the From and To fields.
Dashboard Table 24 RMON History Group Dashboard controls Control Description Owner Displays a text string that identifies the person or entity that created this History Group. RMON Alarm Group Information To display the following form, select RMON > Alarm (click the underlined text, not the folder). This form displays information for all configured RMON Alarm Groups.
Dashboard The following table describes the RMON Alarm Group Dashboard controls: Table 25 RMON Alarm Group Dashboard controls Control Description Search Range To search for a RMON Alarm Group, enter a range of numbers in the From and To fields.
Dashboard RMON Event Group Information To display the following form, select RMON > Event (click the underlined text, not the folder). This form displays information for all configured RMON Event Groups. The following table describes the RMON Event Group Dashboard controls: Table 26 RMON Event Group Dashboard controls Control Description Search Range To search for a RMON Event Group, enter a range of numbers in the From and To fields.
Dashboard IP Interfaces Dashboard To display the following form, select Layer 3 > IP Interfaces (click the underlined text, not the folder). The following table describes the IP Interfaces Dashboard controls: Table 27 IP Interfaces Dashboard controls Control Description Search Range To search for an IP Interface, enter a range of IP Interface numbers in the From and To fields.
Dashboard Table 27 IP Interfaces Dashboard controls Control Description Broadcast Address Displays the IP Broadcast address for this IP Interface. VLAN ID Displays the VLAN number for this interface. Each interface can belong to one VLAN, although any VLAN can have multiple IP interfaces in it. Route Table Information To display the following form, select Layer 3 > Network Routes (click the underlined text, not the folder).
Dashboard The following table describes the Route Table Information controls: Table 28 Route Table Information controls Control Description Search Operation To focus the search for an IP static route, enter search parameters: • • • • • Route Type Route Tag Routes for a Destination IP Routes to a Gateway IP Route for an IP Interface Fields that have a value of “any” are ignored during the search.
Dashboard The following table describes the Route Table Tag parameter. Table 30 IP Routing Tag information Field Description fixed The address belongs to a host or subnet attached to the switch. static The address is a static route which has been configured on the switch. addr The address belongs to one of the switch’s IP interfaces. rip The address was learned by the Routing Information Protocol (RIP). ospf The address was learned by Open Shortest Path First (OSPF).
Dashboard The following table describes the ARP Cache Information controls: Table 31 ARP Cache Information controls Control Description Show Entries of a Specific Source Port Displays ARP entries for the selected port(s). Show Entries of a Specific VLAN Displays ARP entries for the selected VLAN. Show Entry of a Specific IP Address Displays a single ARP entry by IP address. Clear ARP Cache Clears the ARP data cache. Entry # Displays the numeric identifier of the ARP entry.
Dashboard Network Filters Dashboard To display the following form, select Layer 3 > Network Filters (click the underlined text, not the folder). The following table describes the Network Filters Dashboard controls: Table 33 Network Filters Dashboard controls Control Description Entry Displays the entry number. Local Network Address Displays the starting IP address for the filter. Local Network Mask Displays the IP subnet mask that defines the range of IP addresses that will be accepted by the peer.
Dashboard Route Map Dashboard To display the following form, select Layer 3 > Route Maps (click the underlined text, not the folder). The following table describes the Route Map Dashboard controls: Table 34 Route Map Dashboard controls Control Description Route Map ID Displays the Route Map identifier. Precedence Displays the precedence level for the route map. The smaller the value, the higher the precedence.
Dashboard Route Map Dashboard To display the following form, select Layer 3 > Route Maps (click the underlined text, not the folder). The following table describes the Route Map Dashboard controls: Table 35 Route Map Dashboard controls Control Description Route Map Identifier Numeric identifier for the route map. Precedence The precedence of the route map. The smaller the value, the higher the precedence. Type The type of OSPF metric. The default is type 1.
Dashboard Table 35 Route Map Dashboard controls Control Description Network Filter Action Action associated with the network filter for the access list: permit or deny Enable/Disable Access List Status of the access list: enabled or disabled. Default Gateways Dashboard To display the following form, select Layer 3 > Default Gateways (click the underlined text, not the folder).
Dashboard Table 36 Default Gateways Dashboard controls Control Description Search Options To focus the search for a Default Gateway, enter optional search parameters: • IP Address • Subnet Mask • Default Gateway State Fields that have a value of “any” are ignored during the search. Choose a search operation: • or: Search for Default Gateways specified in the search range that meet any of the criteria entered.
Dashboard IGMP Snooping Dashboard To display the following form, select Layer 3 > IGMP > IGMP Snooping (click the underlined text, not the folder).
Dashboard IGMP Multicast Groups The following table describes the IGMP Multicast Groups information. Table 37 IGMP Multicast Groups information Field Description Group Displays the IP address of the IGMP Multicast Group. VLAN Displays the VLAN number of the IGMP Multicast Group. Version Displays the IGMP version. Ports Displays the port numbers of ports that carry IGMP Multicast traffic for the group.
Dashboard IGMP Filters Dashboard To display the following form, select Layer 3 > IGMP > IGMP Filters (click the underlined text, not the folder). The following table describes the IGMP Filter information. Table 39 IGMP Filters information Field Description Filter ID Displays the IGMP filter number. Enabled? Displays the status of the filter (enabled or disabled). Action Displays the action defined for the filter. Range Displays the range of IP addresses configured for the filter.
Dashboard IGMP Static Multicast Router Configuration To display the following form, select Layer 3 > IGMP > IGMP Static Mrouter (click the underlined text, not the folder). The following table describes the IGMP Static multicast router (Mrouter) information. Table 40 IGMP Static Multicast Router information Field Description Mrouter Port Displays the port where the static Mrouter is configured. Vlan Displays the VLAN number of the IGMP Multicast Group. Version Displays the IGMP version.
Dashboard OSPF General Dashboard To display the following form, select Layer 3 > OSPF > General. This form summarizes general OSPF information.
Dashboard OSPF Areas Dashboard To display the following form, select Layer 3 > OSPF > OSPF Areas (click the underlined text, not the folder). Select an area number to view statistics for the OSPF area. OSPF Summary Ranges Dashboard To display the following form, select Layer 3 > OSPF > Summary Ranges (click the underlined text, not the folder).
Dashboard Table 41 OSPF Summary Ranges Dashboard controls Control Description Summary Address List Displays the summary address list for the range. OSPF IP Interfaces Dashboard To display the following form, select Layer 3 > OSPF > OSPF Interfaces (click the underlined text, not the folder). The following table describes the OSPF IP Interfaces Dashboard controls. Select an IP Interface ID number to view statistics for the interface.
Dashboard OSPF IP Interface Dashboard To display the following form, go to the OSPF Interfaces Dashboard, and select an interface number. This form summarizes information about the OSPF interface.
Dashboard OSPF Virtual Links Dashboard To display the following form, select Layer 3 > OSPF > Virtual Links (click the underlined text, not the folder). The following table describes the OSPF Virtual Links Dashboard controls: Table 43 OSPF Virtual Links Dashboard controls Control Description Virtual Link Displays the virtual link number. Enabled? Displays the status of the virtual link, either enabled or disabled. Area Number Displays the area number associated with the virtual link.
Dashboard OSPF Routes To display the following form, select Layer 3 > OSPF > Routes (click the underlined text, not the folder). This form summarizes OSPF route information. RIP General Information To display the following form, select Layer 3 > RIP > General. The following table describes the Routing Information Protocol (RIP) General Information controls: Table 44 RIP General Information controls Control Description Global RIP Enabled State Displays the global state of RIP: enabled or disabled.
Dashboard RIP Interfaces Dashboard To display the following form, select Layer 3 > RIP > RIP Interfaces (click the underlined text, not the folder). The following table describes the RIP Interfaces Dashboard controls: Table 45 RIP Interfaces Dashboard controls Control Description Search Range To search for a RIP interface, enter a range of interface ID numbers in the From and To fields.
Dashboard Table 45 RIP Interfaces Dashboard controls Control Description Poisoned Reverse Displays whether Poisoned Reverse is enabled or disabled. Triggered Updates Displays whether Triggered Updates is enabled or disabled. Multicast Updates Displays whether Multicast Updates is enabled or disabled. Metric Displays the route metric for the interface. Auth Type Displays the authentication type for the interface. Auth Key Displays the authentication key for the interface.
Dashboard Virtual Router Group Operation To display the following form, select Layer 3 > VRRP > General. The following table describes the VRRP General controls: Table 46 Virtual Router Group Operation controls Control Description Set Virtual Router Group to Backup Forces the master virtual router group into backup mode. This is generally used for passing master control back to a preferred switch once the preferred switch has been returned to service after a failure.
Dashboard Virtual Routers Dashboard To display the following form, select Layer 3 > VRRP > Virtual Routers (click the underlined text, not the folder). The following table describes the Virtual Routers Dashboard controls: Table 47 Virtual Routers Dashboard controls Control Description Search Operation To focus the search for virtual routers, enter search parameters: • Virtual Router number • IP address Fields that have a value of “any” are ignored during the search.
Dashboard Virtual Router Operation To display the following form, go to the Virtual Routers Dashboard. Select a virtual router number. The following table describes the Virtual Router Operation controls: Table 48 Virtual Router Operation controls Control Description Set Virtual Router to Backup Forces the master virtual router into backup mode. This is generally used for passing master control back to a preferred switch once the preferred switch has been returned to service after a failure.
Dashboard VRRP IP Interfaces Dashboard To display the following form, select Layer 3 > VRRP > VRRP Interfaces(click the underlined text, not the folder). The following table describes the Virtual Routers Dashboard controls: Table 49 VRRP IP Interfaces Dashboard controls Control Description Search Operation To focus the search for virtual routers, enter search parameters: • IP Interfaces • IP address • VLAN Identifier Fields that have a value of “any” are ignored during the search.
Dashboard Domain Name System Dashboard To display the following form, select Layer 3 > Domain Name System. This form summarizes DNS information. Bootstrap Protocol Relay Dashboard To display the following form, select Layer 3 > Bootstrap Protocol Relay. This form summarizes BOOTP information.
Dashboard IP Routing Dashboard To display the following form, select Layer 3 > General. This form summarizes IP Routing information. 802.1p Priority to CoS Dashboard To display the following form, select QoS > 802.1p > Priority - CoS. This form shows the mapping between 802.1p Priority and Class of Service queue assignment.
Dashboard 802.1p CoS Weight Dashboard To display the following form, select QoS > 802.1p > CoS – Weight. This form shows the scheduling weight for each Class of Service queue. 802.1p Switch Ports Priority Table Dashboard To display the following form, select QoS > 802.1p > Ports Priority Table. This form shows the 802.1p priority value, Class of Service queue assignment, and scheduling weight for each switch port.
Dashboard 802.1p Number of CoS Dashboard To display the following form, select QoS > 802.1p > Number of CoS. This form shows the number of Class of Service queues configured for the switch.
Dashboard ACL Dashboard To display the following form, select Access Control > Access Control Lists (click the underlined text, not the folder). This form summarizes information for configured Access Control Lists (ACLs).
Dashboard Access Control List Dashboard To display the following form, go to the Access Control Lists form. Select an ACL number. This form shows the configured parameters for the ACL.
Dashboard ACL Groups Dashboard Table To display the following form, select Access Control > Access Control List Groups (click the underlined text, not the folder). This form summarizes information for configured Access Control List (ACL) Groups. Access Control List Group Dashboard To display the following form, go to the Access Control List Groups form. Select an ACL Group number. This form shows the ACLs that reside within the selected ACL Group.
Dashboard Uplink Failure Detection Dashboard To display the following form, select Uplink Failure Detection (click the underlined text, not the folder). The following table describes the Uplink Failure Detection Dashboard controls: Table 50 Uplink Failure Detection Dashboard controls Control Description UFD State Displays the global status of Uplink Failure Detection. FDP State Displays whether the Failure Detection Pair is enabled or disabled.
Viewing statistics Viewing statistics Introduction The switch BBI can be used to view a variety of switch performance statistics. The same statistics that are available through the switch’s command line interface are present on the BBI statistics forms. The following provides a basic outline for viewing statistics. You should first be familiar with configuration as covered in the HP 10Gb Ethernet BL-c Switch Command Reference.
Viewing statistics View the statistics in the forms window. For example: NOTE: Items that load other forms when selected are underlined. Select an underlined item to view details on a per port basis. For example: NOTE: This page is refreshed every 5 seconds.
Viewing statistics Management Processor Statistics To display the following form, select System > General. This form displays a summary of management processor (MP) statistics. MP statistics are described in the following table: Table 51 Management Processor Statistics Statistic Syntax and Usage IF Stats Click IF Stats to display IF portion of TCP/IP statistics IP Stats Click IP Stats to display IP portion of TCP/IP statistics.
Viewing statistics TCP/IP Statistics (IF and IP Statistics) To display the following form, go to the Management Processor Statistics form. Select one of the following: IF Stats, IP Stats, ICMP Stats, or TCP Stats. The following table describes the interface statistics: Table 52 IF statistics Statistics Description ifInOctets The total number of octets received on the interface, including framing characters.
Viewing statistics Table 52 IF statistics Statistics Description ifInErrors For packet-oriented interfaces, the number of inbound packets that contained errors preventing them from being delivered to a higher-layer protocol. For character-oriented or fixed-length interfaces, the number of inbound transmission units that contained errors preventing them from being deliverable to a higher-layer protocol.
Viewing statistics Table 53 IP Statistics Statistic Description ipOutDiscards The number of output IP datagrams for which no problem was encountered to prevent their transmission to their destination, but which were discarded (for example, for lack of buffer space). Note that this counter would include datagrams counted in ipForwDatagrams if any such packets met this (discretionary) discard criterion.
Viewing statistics ICMP statistics are described in the following table: Table 54 ICMP Statistics Statistic Description icmpInMsgs The total number of ICMP messages which the entity (the switch) received. Note that this counter includes all those counted by icmpInErrors. icmpOutMsgs The total number of ICMP messages which this entity (the switch) attempted to send. Note that this counter includes all those counted by icmpOutErrors.
Viewing statistics Table 54 ICMP Statistics Statistic Description icmpOutAddrMaskReps The number of ICMP Address Mask Reply messages sent. TCP statistics are described in the following table: Table 55 TCP Statistics Statistic Description tcpInSegs The total number of segments received, including those received in error. This count includes segments received on currently established connections.
Viewing statistics Table 55 TCP Statistics Statistic Description Remote Port TCP port used by the remote device. Source Address IP address of TCP source connections. Local Port Available TCP ports used for connecting to the switch. State State of each TCP connection. UDP/SNMP Statistics To display the following form, go to the Management Processor Statistics form. Select UDP Stats or SNMP Stats.
Viewing statistics To display the following form, go to the Management Processor Statistics form. Select UDP Stats or SNMP Stats, and scroll down. SNMP statistics are described in the following table: Table 57 SNMP Statistics Statistic Description snmpInPkts The total number of Messages delivered to the SNMP entity from the transport service. snmpOutPkts The total number of SNMP Messages that were passed from the SNMP protocol entity to the transport service.
Viewing statistics Table 57 SNMP Statistics Statistic Description snmpOutBadValues The total number of SNMP Protocol Data Units (PDUs), which were generated by the SNMP protocol entity and for which the value of the error-status field is badValue. snmpInSetRequests The total number of SNMP Set-Request Protocol Data Units (PDUs), which have been accepted and processed by the SNMP protocol entity.
Viewing statistics Table 57 SNMP Statistics Statistic Description snmpInASNParseErrs The total number of ASN.1 or BER errors encountered by the SNMP protocol entity when decoding SNMP Messages received. NOTE: OSI’s method of specifying abstract objects is called ASN.1 (Abstract Syntax Notation One, defined in X.208), and one set of rules for representing such objects as strings of ones and zeros is called the BER (Basic Encoding Rules, defined in X.209). ASN.
Viewing statistics FDB Statistics To display the following form, go to the Management Processor Statistics form. Select FDB Stats. Forwarding Database (FDB) statistics are described in the following table: Table 59 Forwarding Database Statistics Statistic Description current Current number of entries in the Forwarding Database. hiwat Highest number of entries recorded at any given time in the Forwarding Database.
Viewing statistics Network Time Protocol Statistics To display the following form, select System > NTP. Network Time Protocol (NTP) statistics for the primary and secondary NTP servers are described in the following table: Table 60 NTP Statistics Statistic Description Request Sent The total number of NTP requests the switch sent to the primary NTP server to synchronize time. Responses Received The total number of NTP responses received from the primary/secondary NTP server.
Viewing statistics Switch Ports Statistics Summary To display the following form, select Switch Ports (click the underlined text, not the folder). This form displays traffic statistics on a port-by-port basis. For more information, select a port number to display detailed statistics for that port.
Viewing statistics Port Statistics To display the following form, go to the Switch Ports Statistics Summary form. Select a Switch Port number.
Viewing statistics Port statistics are described in the following table: Table 61 Port Statistics Control Description Clear Port x Statistics Select Clear and click Submit to clear statistics for this port. Operational Status Enables or disables the port. RMON Operational Status Enables or disables RMON for the port. The next several tables contain specific information about bridging, interface (input and output), and Ethernet statistics.
Viewing statistics Table 63 Interface Statistics for a Port - Input Statistic Description HC BcastPkts The number of packets, delivered by this sub layer to a higher sub layer, which were addressed to a broadcast address at this sub layer. HC MCastPkts The total number of packets that higher-level protocols requested to be transmitted, and which were addressed to a multicast address at this sub layer, including those that were discarded or not sent.
Viewing statistics Ethernet (“dot3”) Statistics The following table describes the Ethernet statistics of the selected port: Table 65 Ethernet Statistics for a Port Statistic Description Align Errors A count of frames received on a particular interface that is not an integral number of octets in length and do not pass the Frame Check Sequence (FCS) check.
Viewing statistics Table 65 Ethernet Statistics for a Port Statistic Description Frame Too Longs A count of frames received on a particular interface that exceeds the maximum permitted frame size. The count represented by an instance of this object is incremented when the frameTooLong status is returned by the MAC service to the LLC (or other MAC user). Received frames for which multiple error conditions obtained are, according to the conventions of IEEE 802.
Viewing statistics Switch Ports 802.1x Statistics To display the following form, select Layer 2 > 802.1x > Switch Ports. The following table describes 802.1x port statistics: Table 67 Switch Port 802.1x Statistics Statistic Description Port Displays port numbers. Last EAPOL Frame Source Displays the MAC address of the most recent 802.1x frame received on the port. Frame Version Displays the version number of the most recent 802.1x frame received on the port.
Viewing statistics Port 802.1x Statistics To display the following form, go to the Switch Ports 802.1x Statistics form. Select a port number.
Viewing statistics The following table describes 802.1x port statistics: Table 68 Switch Port 802.1x Statistics Statistic Description Authenticator Diagnostics authEntersConnecting Total number of times that the state machine transitions to the CONNECTING state from any other state. authEapLogoffsWhileConnecting Total number of times that the state machine transitions from CONNECTING to DISCONNECTED as a result of receiving an EAPOL-Logoff message.
Viewing statistics Table 68 Switch Port 802.1x Statistics Statistic Description backendOtherRequestsToSupplicant Total number of times that the state machine sends an EAP-Request packet (other than an Identity, Notification, Failure, or Success message) to the Supplicant. Indicates that the Authenticator chose an EAP-method.
Viewing statistics LACP Statistics To display the following form, select Layer 2 > LACP. Enter a port number to show LACP Statistics for the port. The following table describes LACP statistics: Table 70 LACP Statistics Statistic Description Port Displays the port number. Show Enter a port number and select Show to display LACP statistics for the port. Valid LACPDUs received Total number of LACP data units received. Valid Marker PDUs received Not applicable (see note).
Viewing statistics IP Statistics To display the following form, select Layer 3 > IP Interfaces (click the underlined text, not the folder). The following table describes IP statistics: Table 71 IP Statistics Statistic Description ipInReceives The total number of input datagrams received from interfaces, including those received in error.
Viewing statistics Table 71 IP Statistics Statistic Description ipDefaultTTL The default value inserted into the Time-To-Live (TTL) field of the IP header of datagrams originated at this entity (the switch), whenever a TTL value is not supplied by the transport layer protocol.
Viewing statistics IP Routing Management Statistics (part one) To display the following form, select Layer 3 > Network Routes. To clear statistics counters, select clear from the drop-down list next to the statistics group you wish to clear, and click Submit.
Viewing statistics The following table describes IP Routing Management statistics: Table 72 IP Routing Management Statistics Statistic Description InReceives The total number of input datagrams received from interfaces, including those received in error. InDelivers The total number of input datagrams successfully delivered to IP user-protocols (including ICMP).
Viewing statistics The following table describes the Address Resolution Protocol (ARP) statistics: Table 75 ARP statistics Statistics Description Current Entries The total number of outstanding ARP entries in the ARP table. High Water Mark The highest number of ARP entries ever recorded in the ARP table. Maximum Entries The maximum number of ARP entries that are supported.
Viewing statistics Table 76 ICMP statistics Statistics Description icmpInParmProbs The number of ICMP Parameter Problem messages received. icmpInSrcQuenchs The number of ICMP Source Quench (buffer almost full, stop sending data) messages received. icmpInRedirects The number of ICMP Redirect messages received. icmpInEchos The number of ICMP Echo (request) messages received. icmpInEchoReps The number of ICMP Echo Reply messages received.
Viewing statistics The following table describes the Transmission Control Protocol (TCP) statistics: Table 77 TCP statistics Statistics Description tcpRtoAlgorithm The algorithm used to determine the timeout value used for retransmitting unacknowledged octets. tcpRtoMin The minimum value permitted by a TCP implementation for the retransmission timeout, measured in milliseconds. More refined semantics for objects of this type depend upon the algorithm used to determine the retransmission timeout.
Viewing statistics The following table describes the User Datagram Protocol (UDP) statistics: Table 78 UDP statistics Statistics Description udpInDatagrams The total number of UDP datagrams delivered to the switch. udpOutDatagrams The total number of UDP datagrams sent from this switch. udpInErrors The number of received UDP datagrams that could not be delivered for reasons other than the lack of an application at the destination port.
Viewing statistics IGMP VLAN Snooping Statistics Summary To display the following form, select Layer 3 > IGMP > IGMP Snooping (click the underlined text, not the folder). The following table describes IGMP VLAN Snooping statistics: Table 80 IGMP VLAN Snooping Statistics Summary Statistic Description Clear IGMP Statistics To clear all IGMP Snooping statistics, select clear in the drop-down list, and click Submit. VLAN# Displays each VLAN with a summary of IGMP statistics for the VLAN.
Viewing statistics VLAN - IGMP Snooping Statistics To display the following form, go to the IGMP VLAN Snooping Statistics Summary form. Select a VLAN number. The following table describes IGMP VLAN Snooping statistics for the selected VLAN: Table 81 VLAN - Snooping Statistics Statistic Description Clear IGMP VLAN x Statistics To clear IGMP Snooping statistics on the VLAN, select clear in the drop-down list, and click Submit.
Viewing statistics Table 81 VLAN - Snooping Statistics Statistic Description rxIgmpV3CurrentState Records Total number of Current State records received rxIgmpV3SourceListChange Records Total number of Source List Change records received rxIgmpV3FilterChange Records Total number of Filter Change records received.
Viewing statistics OSPF General Statistics To display the following form, select Layer 3 > OSPF > General.
Viewing statistics The following table describes OSPF General statistics: Table 82 OSPF General Statistics Statistic Description OSPF Rx/Tx Statistics Rx Statistics pkts The sum total of all OSPF packets received on all OSPF areas and interfaces. hello The sum total of all Hello packets received on all OSPF areas and interfaces. database The sum total of all Database Description packets received on all OSPF areas and interfaces.
Viewing statistics Table 82 OSPF General Statistics Statistic Description exchange done The sum total number of neighbors in this state (that is, in an adjacency's final state) having transmitted a full sequence of Database Description packets, across all OSPF areas and interfaces. bad requests The sum total number of Link State Requests which have been received for a link state advertisement not contained in the database across all interfaces and OSPF areas.
Viewing statistics OSPF Areas Statistics To display the following form, select Layer 3 > OSPF > OSPF Areas (click the underlined text, not the folder). Select an area number to view detailed statistics.
Viewing statistics OSPF Area Statistics To display the following form, go to the OSPF Areas Statistics form. Select an area number.
Viewing statistics The following table describes OSPF Area statistics: Table 83 OSPF Area Statistics Statistic Description OSPF Rx/Tx Statistics Rx Statistics pkts The sum total of all OSPF packets received on all OSPF areas and interfaces. hello The sum total of all Hello packets received on all OSPF areas and interfaces. database The sum total of all Database Description packets received on all OSPF areas and interfaces.
Viewing statistics Table 83 OSPF Area Statistics Statistic Description exchange done The sum total number of neighbors in this state (that is, in an adjacency's final state) having transmitted a full sequence of Database Description packets, across all OSPF areas and interfaces. bad requests The sum total number of Link State Requests which have been received for a link state advertisement not contained in the database across all interfaces and OSPF areas.
Viewing statistics OSPF IP Interfaces Statistics To display the following form, select Layer 3 > OSPF > OSPF Interfaces (click the underlined text, not the folder). The following table describes the OSPF IP Interfaces Statistics controls: Table 84 OSPF IP Interface statistics Control Description Search Operation To focus the search for an OSPF IP interface, enter search parameters: • IP Interfaces • Area number • State Fields that have a value of “any” are ignored during the search.
Viewing statistics OSPF IP Interface Statistics To display the following form, go to the OSPF IP Interfaces Statistics form. Select an interface ID number.
Viewing statistics The following table describes OSPF interface statistics: Table 85 OSPF Interface Statistics Statistic Description OSPF Rx/Tx Statistics Rx Statistics Pkts The sum total of all OSPF packets received on all OSPF areas and interfaces. hello The sum total of all Hello packets received on all OSPF areas and interfaces. database The sum total of all Database Description packets received on all OSPF areas and interfaces.
Viewing statistics Table 85 OSPF Interface Statistics Statistic Description exchange done The sum total number of neighbors in this state (that is, in an adjacency's final state) having transmitted a full sequence of Database Description packets, across all OSPF areas and interfaces. bad requests The sum total number of Link State Requests which have been received for a link state advertisement not contained in the database across all interfaces and OSPF areas.
Viewing statistics RIP Statistics To display the following form, select Layer 3 > RIP > General. This form provides basic Routing Information Protocol (RIP) statistics. Virtual Router Redundancy Protocol Statistics To display the following form, select Layer 3 > VRRP > General.
Viewing statistics The following table describes VRRP statistics: Table 86 Virtual Router Redundancy Protocol Statistics Statistic Description InAdvertisements The total number of VRRP advertisements that have been received. BadAdvertisements The total number of VRRP advertisements received that were dropped. OutAdvertisements The total number of VRRP advertisements that have been sent. BadVersion The total number of VRRP advertisements that had a bad version number.
Viewing statistics IP Routing Management Statistics (part one) To display the following form, select Layer 3 > General. To clear statistics counters, select clear from the drop-down list next to the statistics group you wish to clear, and click Submit.
Viewing statistics The following table describes IP Routing Management statistics: Table 88 IP Routing Management Statistics Statistic Description InReceives The total number of input datagrams received from interfaces, including those received in error. InDelivers The total number of input datagrams successfully delivered to IP user-protocols (including ICMP).
Viewing statistics The following table describes the Address Resolution Protocol (ARP) statistics: Table 91 ARP statistics Statistics Description Current Entries The total number of outstanding ARP entries in the ARP table. High Water Mark The highest number of ARP entries ever recorded in the ARP table. Maximum Entries The maximum number of ARP entries that are supported.
Viewing statistics Table 92 ICMP statistics Statistics Description icmpInParmProbs The number of ICMP Parameter Problem messages received. icmpInSrcQuenchs The number of ICMP Source Quench (buffer almost full, stop sending data) messages received. icmpInRedirects The number of ICMP Redirect messages received. icmpInEchos The number of ICMP Echo (request) messages received. icmpInEchoReps The number of ICMP Echo Reply messages received.
Viewing statistics The following table describes the Transmission Control Protocol (TCP) statistics: Table 93 TCP statistics Statistics Description tcpRtoAlgorithm The algorithm used to determine the timeout value used for retransmitting unacknowledged octets. tcpRtoMin The minimum value permitted by a TCP implementation for the retransmission timeout, measured in milliseconds. More refined semantics for objects of this type depend upon the algorithm used to determine the retransmission timeout.
Viewing statistics The following table describes the User Datagram Protocol (UDP) statistics: Table 94 UDP statistics Statistics Description udpInDatagrams The total number of UDP datagrams delivered to the switch. udpOutDatagrams The total number of UDP datagrams sent from this switch. udpInErrors The number of received UDP datagrams that could not be delivered for reasons other than the lack of an application at the destination port.
Viewing statistics Access Control Lists Statistics To display the following form, select Access Control > Access Control Lists (click the underlined text, not the folder). This form allows you to select an Access Control List (ACL) and view statistics. ACL Statistics To display the following form, go to the ACL Statistics Table, and select an ACL number. This form summarizes the number of matches (hits) for the ACL.
Viewing statistics Uplink Failure Detection Statistics To display the following form, select Uplink Failure Detection (click the underlined text, not the folder). The following table describes commands for Uplink Failure Detection (UFD) statistics: Table 95 Uplink Failure Detection Statistics Control Description Clear UFD Statistics To clear UFD statistics, select clear in the drop-down list, and click Submit.
Configuring the switch Configuring the switch Introduction The switch BBI can be used to view and change switch configuration parameters. The same configuration parameters that are available through the switch’s command-line interface are present on the BBI configuration forms. The following provides a basic outline for switch configuration. You should first be familiar with configuration as covered in the HP 10Gb Ethernet BL-c Switch Command Reference.
Configuring the switch 3. View or make changes to the settings shown in the forms window. For example: NOTE: Some fields are highlighted on the forms in green type — they must be configured for proper switch operations. Underlined items load other forms when selected. 4. Submit the form contents using the button on the bottom of the form. When the Submit button is selected, the form is sent to the switch.
Configuring the switch Applied changes take effect on the switch immediately, but are lost the next time the switch is rebooted, unless the Save command is selected. When you click Save, you have two save options: Save and Save n. With Save, your new configuration changes are placed in the active configuration block. The previous configuration is copied into the backup configuration block.
Configuring the switch Switch Management Processor Configuration Basic system configuration To display the following form, select System > General.
Configuring the switch The following table describes the Switch Management Processor Configuration (basic) controls: Table 96 Switch Management Processor Configuration (Basic) controls Control Description Switch IP Address Configures the IP address of the switch interface using dotted decimal notation. Switch IP Subnet Mask Configures the IP subnet address mask for the interface using dotted decimal notation. Enable/Disable BOOTP for IP Management Enables or disables the use of BOOTP.
Configuring the switch Table 96 Switch Management Processor Configuration (Basic) controls Control Description Telnet Access Enables or disables Telnet access to the switch. To activate this control, you must enable BBI configuration of Telnet from the CLI (/cfg/sys/access/tsbbi). Telnet Port (1-65535) Sets an optional telnet server port number for cases where the server listens for telnet sessions on a non-standard port. The default is 23.
Configuring the switch SSH and SNMP controls To display the following form, select System > General. The following table describes the Secure Shell (SSH) controls: NOTE: To activate SSH configuration controls in the BBI, you must enable the controls from the CLI (/cfg/sys/access/tsbbi).
Configuring the switch Table 97 SSH controls Control Description SSH Time Interval (0-24 hours, 0 – disable) Defines interval for auto-generating the RSA server key. The switch will autogenerate the RSA server key at the interval defined by this command. The value of zero (0) means the RSA server key autogeneration is disabled. If the switch has been busy performing any other key generation and the assigned time of interval expires, the RSA server will skip generating the key.
Configuring the switch Table 98 Simple Network Management Protocol (SNMP) controls Control Description SNMP state machine timeout (1-30 minutes) Sets the timeout value for the SNMP state machine. Send SNMP Auth. Failure Traps? Enables or disables the use of the system authentication trap facility. The default setting is disabled.
Configuring the switch User Configuration Table To display the following form, select System > User Table. This form summarizes the users configured on the switch. Click Add User to define a new user. Select a user ID number to update the user’s configuration. Click Change User/Oper/Admin password to configure new passwords for the switch. To remove an end-user from switch, enter the user name and click Eject user.
Configuring the switch User Access Control Configuration To display the following form, go to the User Configuration Table and select a user ID number, or click Add User. The following table describes User Access Configuration controls: Table 100 User Access Configuration controls Control Description User ID (1-10) Sets a numeric identifier for the user. Set Class of Service Sets the Class-of-Service to define the user’s authority level.
Configuring the switch Switch RADIUS Configuration To display the following form, select System > Radius. The following table describes Switch Radius Configuration controls: Table 101 Switch RADIUS Configuration controls Control Description Primary Radius IP Address Configures the primary Radius server address. Secondary Radius IP Address Configures the secondary Radius server address. Radius port (1500-3000) Configures the number of the UDP port to be configured, between 1500 and 3000.
Configuring the switch Table 101 Switch RADIUS Configuration controls Control Description Radius Secret Defines the shared secret (up to 32 characters) between the switch and the RADIUS server(s). Secondary Radius Server Secret Defines the secondary shared secret (up to 32 characters) between the switch and the Radius server(s). IMPORTANT: If RADIUS is enabled, you must login using RADIUS authentication when connecting via the console or Telnet/SSH/HTTP/HTTPS.
Configuring the switch Switch TACACS+ Configuration To display the following form, select System > Tacacs+. TACACS+ (Terminal Access Controller Access Control System) is an authentication protocol that allows a remote access server to forward a user's logon password to an authentication server to determine whether access can be allowed to a given system. TACACS+ and Remote Authentication Dial-In User Service (RADIUS) protocols are more secure than the TACACS encryption protocol.
Configuring the switch TACACS+ offers the following advantages over RADIUS as the authentication device: • • • TACACS+ is TCP-based, so it facilitates connection-oriented traffic. It supports full-packet encryption, as opposed to password-only in authentication requests. It supports decoupled authentication, authorization, and accounting.
Configuring the switch servers are not available.
Configuring the switch NTP Configuration To display the following form, select System > NTP. This form enables you to synchronize the switch clock to a Network Time Protocol (NTP) server. By default, this option is disabled. The following table describes NTP Configuration controls: Table 103 NTP Configuration controls Control Description NTP Server IP Address Configures the IP address of the primary NTP server to which you want to synchronize the switch clock.
Configuring the switch Syslog and Trap Feature Configuration To display the following form, select System > Syslog/Trap Features. The following table describes Syslog and Trap Feature Configuration controls: Table 104 Syslog and Trap Feature Configuration controls Control Description Enable/Disable Syslog and Trap of Console Enables or disables syslog messages and traps of console-related events.
Configuring the switch Table 104 Syslog and Trap Feature Configuration controls Control Description Enable/Disable Syslog and Trap of VLAN Enables or disables syslog messages and traps of VLAN-related events. Enable/Disable Syslog and Trap of WEB Enables or disables syslog messages and traps of Web-related events. Enable/Disable Syslog and Trap of IP Enables or disables syslog messages and traps of IP-related events.
Configuring the switch Switch Image and Configuration Management To display the following form, select System > Config/Image Control.
Configuring the switch The switch software image is the executable code running on the switch. A version of the image ships with the switch, and comes pre-installed on the device. As new versions of the image are released, you can upgrade the software running on your switch.
Configuring the switch Table 105 Switch Image and Configuration Management controls Control Description Next Boot Image Selection Selects which software image (image1 or image2) you want to run in switch memory for the next reboot. Active Configuration Block Displays the Configuration Block file that is currently running (active or backup). Next Boot Configuration Block Selection Selects the Configuration Block file (active or backup) that will run after the next reboot.
Configuring the switch Switch Image and Configuration Management buttons The following table describes Switch Image and Configuration Management buttons: Table 106 Switch Image and Configuration Management buttons Button Description Get Image Starts download of the software image file indicated in TFTP Image Filename field from the specified TFTP server. Put Image Starts upload of the software image file indicated in TFTP Image Filename field from the specified TFTP server.
Configuring the switch Management Network Definition Configuration To display the following form, select System > Mgmt. The following table describes the Management Network Definition Configuration controls: Table 107 Management Network Definition Configuration controls Control Description Index Displays the index number that identifies each management network.
Configuring the switch Switch Ports Configuration To display the following form, select System > Switch Ports (click the underlined text, not the folder). This form summarizes the configuration of each port. Select a switch port number to go to its configuration form.
Configuring the switch Switch Port Configuration To display the following form, go to the Switch Ports Configuration form. Select a Switch Port number. This form allows you to configure settings for individual switch ports. The following table describes the Switch Port Configuration controls: Table 108 Switch Port Configuration controls Control Description Switch Port State Enables or disables the port. RMON Instrumentation Enables or disables Remote Monitoring for the port.
Configuring the switch Table 108 Switch Port Configuration controls Control Description PVID Tagging Disables or enables VLAN tag persistence. When disabled, the VLAN tag is removed from packets whose VLAN tag matches the port PVID. The default value is enabled. Port STP Turns Spanning Tree On or Off for this port. Default Port VLAN ID (1-4094) Sets the default VLAN number which will be used to forward frames which are not VLAN tagged. The default number is 1.
Configuring the switch Table 108 Switch Port Configuration controls Control Description Destination Lookup Fail Threshold Rate (0-262143) Configures the threshold rate for destination lookup failures, in packets per second. 802.1p Port Priority (0-7) Configures the port’s 802.1p priority level.
Configuring the switch Switch Port ACL Configuration To display the following form, go to the Switch Ports Configuration form. Select a Switch Port number. This form allows you to configure Access Control List settings for individual switch ports. The following table describes the Switch Port ACL Configuration controls: Table 109 Switch Port ACL Configuration controls Control Description ACLs Available Lists the ACLs that you can add to the port. ACLs Selected Lists the ACLs associated with the port.
Configuring the switch Table 109 Switch Port ACL Configuration controls Control Description ACL Groups Selected Lists the ACL Groups associated with the port. Select an ACL Group number in the ACL Groups Available list, and click Add to add the ACL Group to the port. Select an ACL Group number in the ACL Groups Selected list, and click Remove to remove the ACL Group from the port.
Configuring the switch Monitoring Port Configuration To display the following form, go to the Port-Based Port Mirroring Configuration form. Select a Monitoring Port number. This form lists all mirrored ports for the selected port number. Click Add Mirrored Port to select a port to be monitored by this port. Click Delete Monitor Port to remove all mirrored ports from this port’s monitoring configuration.
Configuring the switch 802.1x General Configuration To display the following form, select Layer 2 > 802.1x > General. The following table describes the General 802.1x Configuration controls: Table 112 General 802.1x Configuration controls Control Description System Status Enables or disables 802.1x Port-Based Network Access Control. 802.1x Switch Ports Configuration To display the following form, select Layer 2 > 802.1x > Switch Ports. Select a port number to view the Switch Port 802.
Configuring the switch 802.1x Port Configuration To display the following form, go to the Switch Ports 802.1x Configuration form. Select a port number. The following table describes the Port 802.1x Configuration controls: Table 113 Port 802.1x Configuration controls Control Description Auth Mode Sets the type of access control for all ports: • force-unauth—the port is unauthorized unconditionally. • auto—the port is unauthorized until it is successfully authorized by the RADIUS server.
Configuring the switch Table 113 Port 802.1x Configuration controls Control Description Server Timeout (0-65535 sec) Sets the time, in seconds, the authenticator waits for a response from the Radius server before declaring an authentication timeout. The default value is 30 seconds. The time interval between transmissions of the RADIUS Access-Request packet containing the supplicant’s (client’s) EAP-Response packet is determined by the current setting of /cfg/sys/radius/timeout (default is 3 seconds).
Configuring the switch Static FDB Configuration (part one) To display the following form, select Layer 2 > FDB >Static FDB (click the underlined text, not the folder). This form summarizes the Static Forwarding Database entries. Select a static FDB ID number to display the Static FDB Configuration form. Click Clear to clear the static FDB entries.
Configuring the switch Static FDB Configuration (part two) To display the following form, select Layer 2 > FDB >Static FDB > Add static FDB entry. The following table describes the Static FDB Configuration controls: Table 115 Static FDB Configuration controls Control Description FDB Table Index (1-128) Configures the index ID number of the static FDB entry. MAC Configures the MAC address of the static FDB entry. Vlan Configures the VLAN for the static FDB entry.
Configuring the switch VLANs Configuration To display the following form, select Layer 2 > Virtual LANs (click the underlined text, not the folder). The following table describes the VLANs Configuration controls: Table 116 VLANs Configuration controls Control Description Search Range To search for a VLAN, enter a range of VLAN numbers in the From and To fields.
Configuring the switch VLAN Configuration To display the following form, go to the VLANs Configuration form. Select a VLAN ID, or open the Virtual LANs folder and click Add VLAN. The commands on this form configure VLAN attributes, change the status of the VLAN, delete the VLAN, and change the port membership of the VLAN. By default, the VLAN menu option is disabled except VLAN 1, which is enabled all the time. The HP 10GbE switch supports a maximum of 1,000 VLANs.
Configuring the switch Table 117 VLAN Configuration controls Control Description Ports Available Lists the ports that can be added to the VLAN. Ports in Vlan Lists the ports that are members of the VLAN. Select a port number in the Ports Available list and click Add to add the port to the VLAN membership. Select a port number in the Ports in VLAN list and click Remove to remove the port from the VLAN membership. NOTE: Each port must belong to at least one VLAN.
Configuring the switch The HP 10GbE switch supports the IEEE 802.1d Spanning Tree Protocol (STP) and Per VLAN Spanning Tree (PVST+). You can configure up to 127 Spanning Tree Groups on the switch (STG 128 is reserved for switch management). Spanning Tree is turned on by default. NOTE: When RSTP is turned on, only STP group 1 can be configured.
Configuring the switch Switch Spanning Tree Group Configuration To display the following form, go to the Switch Spanning Tree Groups Configuration form. Select a Spanning Tree Group number, or open the Spanning Tree Groups folder and click Add Spanning Tree Group. Spanning Tree bridge parameters can be configured for each Spanning Tree Group.
Configuring the switch Table 119 Switch Spanning Tree Group Configuration controls Control Description Bridge Priority (0-65535) Configures the bridge priority. The bridge priority parameter controls which bridge on the network is the STP root bridge. To make this switch the root bridge, configure the bridge priority lower than all other switches and bridges on your network. The lower the value, the higher the bridge priority. The range is 0 to 65535, and the default is 32768.
Configuring the switch Switch Spanning Tree Group Port Configuration To display the following form, go to the Switch Spanning Tree Group Configuration form. Select a Switch Port number. Spanning Tree port parameters are used to modify STP operation on an individual port basis. The default configuration for STP/PVST+ is Off for downlink ports (1-16) and the management port (17), and On for uplink ports (18-21).
Configuring the switch Table 120 Switch Spanning Tree Group Port Configuration controls Control Description Link Type Defines the type of link connected to the port, as follows: • auto: Configures the port to detect the link type, and automatically match its settings. • p2p: Configures the port for Point-To-Point protocol. • shared: Configures the port to connect to a shared medium (usually a hub). This command only applies when RSTP is turned on.
Configuring the switch The following table describes the MSTP/RSTP General Configuration controls: Table 121 MSTP/RSTP General Configuration controls Control Description Region Name Configures a name for the MSTP region. All devices within a MSTP region must have the same region name. The Region Name can have a maximum of 32 characters. Revision Level (0-65535) Configures a version number for the MSTP region. The version is used as a numerical identifier for the region.
Configuring the switch Common Internal Spanning Tree Bridge Configuration To display the following form, select Layer 2 > MSTP/RSTP > CIST-Bridge. The CIST provides compatibility with different MSTP regions and with devices running different Spanning Tree instances. It is equivalent to Spanning Tree Group 0.
Configuring the switch Table 122 Common Internal Spanning Tree Bridge Configuration controls Control Description Forward Delay (4-30 secs) Configures the CIST bridge forward delay parameter. The forward delay parameter specifies the amount of time that a bridge port has to wait before it changes from the listening state to the learning state and from the learning state to the forwarding state. The range is 4 to 30 seconds, and the default is 15 seconds. This command does not apply to RSTP.
Configuring the switch Common Internal Spanning Tree Port Configuration To display the following form, go to the Ports Common Internal Spanning Tree Configuration form. Select a CIST Port number. This form summarizes the port CIST parameters. Common Internal Spanning Tree port parameters are used to modify MSTP operation on an individual port basis. For each port, MSTP is turned on by default.
Configuring the switch Table 123 Common Internal Spanning Tree Port Configuration controls Control Description Hello Time (1-10 secs) Configures how often “keep alive” BPDU messages are transmitted. Trunk Groups Configuration To display the following form, select Layer 2 > Trunk Groups. This form provides a summary of the state of all trunk groups.
Configuring the switch Switch Trunk Group Configuration To display the following form, go to the Trunk Groups Configuration form. Select a Trunk Group number. This form enables you to configure a selected switch trunk group. Trunk groups can provide super-bandwidth connections between switches or other trunk capable devices. A trunk is a group of ports that act together, combining their bandwidth to create a single, larger port.
Configuring the switch Layer 2 Trunk Hash Configuration To display the following form, select Layer 2 > Trunk Hash. The following table describes the Layer 2 Trunk Hash Configuration controls: Table 125 Layer 2 Trunk Hash Configuration controls Control Description Smac Enable or disable trunk hashing on the source MAC. Dmac Enable or disable trunk hashing on the destination MAC. Sip Enable or disable trunk hashing on the source IP. Dip Enable or disable trunk hashing on the destination IP.
Configuring the switch LACP Configuration To display the following form, select Layer 2 > LACP. The following table describes the Switch LACP Configuration controls: Table 126 Switch LACP Configuration controls Control Description LACP System Priority (1-65535) Defines the priority value (1 through 65535) for the switch. Lower numbers provide higher priority. The default value is 32768. Timeout time Defines the timeout period before invalidating LACP data from a remote partner.
Configuring the switch LACP Port Configuration To display the following form, go to the Switch LACP Configuration form. Select a port number. The following table describes the LACP Port Configuration controls: Table 127 LACP Port Configuration controls Control Description Port Admin Key Set the admin key for this port. Only ports with the same admin key and oper key (operational state generated internally) can form a LACP trunk group. Port Priority Sets the priority value for the selected port.
Configuring the switch Uplink Fast General Configuration To display the following form, select Layer 2 > UpLink Fast. The following table describes the Uplink Fast Configuration controls: Table 128 Uplink Fast Configuration controls Control Description Enabled? Enables or disables Fast Uplink Convergence, which provides rapid Spanning Tree convergence to an upstream switch during failover.
Configuring the switch RMON History Configuration Table To display the following form, select RMON > History (click the underlined text, not the folder). The following table describes the RMON History Groups Configuration controls: Table 129 RMON History Configuration controls Control Description Search Range To search for a History Group, enter a range of numbers in the From and To fields.
Configuring the switch RMON History Configuration To display the following form, go to the RMON History Groups Configuration form. Select a History Group, or open the History folder and click Add History Group. The following table describes the History Group Configuration controls: Table 130 History Group Configuration controls Control Description History Group ID (1-65535) Configures a numeric identifier for the selected History index. MIB Object ID Configures the interface MIB Object Identifier.
Configuring the switch RMON Alarm Configuration Table To display the following form, select RMON > Alarm (click the underlined text, not the folder).
Configuring the switch The following table describes the Alarm Groups Configuration controls: Table 131 RMON Alarm Configuration controls Control Description Search Range To search for a RMON Alarm, enter a range of numbers in the From and To fields.
Configuring the switch The following table describes the Alarm Group Configuration controls: Table 132 Alarm Group Configuration controls Control Description Alarm Group ID Configures the numeric identifier of the Alarm index. MIB Object ID Configures an alarm MIB Object Identifier. The alarm OID can have a maximum of 127 characters. Rising Limit Configures the rising threshold for the sampled statistic.
Configuring the switch RMON Event Configuration Table To display the following form, select RMON > Event (click the underlined text, not the folder). The following table describes the Event Groups Configuration controls: Table 133 RMON Event Configuration controls Control Description Search Range To search for a RMON Event Group, enter a range of numbers in the From and To fields.
Configuring the switch RMON Event Configuration To display the following form, go to the RMON Event Groups Configuration form. Select an Event Group, or open the Event folder and click Add Event Group. The following table describes the Event Group Configuration controls: Table 134 Event Group Configuration controls Control Description Event Group ID Configures the numeric identifier of this Event index. Event Type Selects the type of notification provided for this event.
Configuring the switch IP Interfaces Configuration To display the following form, select Layer 3 > IP Interfaces (click the underlined text, not the folder). This form summarizes IP Interface parameters. The following table describes IP Interfaces Configuration controls: Table 135 IP Interfaces Configuration controls Control Description Search Range To search for an IP Interface, enter a range of IP Interface numbers in the From and To fields.
Configuring the switch IP Interface Configuration To display the following form, go to the IP Interfaces Configuration form. Select an IP Interface number, or open the IP Interfaces folder and click Add IP Interface. The switch can be configured with up to 250 IP interfaces. Each IP interface represents the switch on an IP subnet on your network. The Interface option is disabled by default.
Configuring the switch IP Static Routes Configuration To display the following form, select Layer 3 > Network Routes (click the underlined text, not the folder). This form summarizes static route parameters.
Configuring the switch IP Static Route Configuration To display the following form, go to the IP Static Routes Configuration form. Select a static route ID number, or open the Network Routes folder and click Add Network Route. The following table describes the IP Static Route Configuration controls: Table 138 IP Static Route Configuration controls Control Description Route Table Index (1-128) Sets the numeric identifier for this index. Destination IP Enter the destination IP address for this route.
Configuring the switch Static ARP Configuration To display the following form, select Layer 3 > ARP (click the underlined text, not the folder). This form summarizes the current static ARP entries. Select a static ARP ID number to display the IP Static ARP Configuration form. IP Static ARP Configuration To display the following form, go to the Static ARP Configuration form. Select a static ARP ID number, or open the ARP folder and click Add Static ARP.
Configuring the switch Table 139 IP Static ARP Configuration controls Control Description MAC Configures the MAC address of the host. VLAN Configures the VLAN ID for the host. Port Configures the port to which the host connects. Network Filters Configuration To display the following form, select Layer 3 > Network Filters (click the underlined text, not the folder). This form summarizes network filter parameters.
Configuring the switch Network Filter Configuration To display the following form, go to the Network Filters Configuration form. Select a network filter ID number, or open the Network Filters folder and click Add Network Filter. The following table describes the Network Filter Configuration controls: Table 141 Network Filter Configuration controls Control Description Network Filter Identifier (1-256) Sets the numeric identifier for this network filter.
Configuring the switch Route Maps Configuration To display the following form, select Layer 3 > Route Maps (click the underlined text, not the folder). The following table describes Route Maps Configuration controls: Table 142 Route Maps Configuration controls Control Search Operation Description To focus the search for a route map, enter optional search parameters: • Route Map ID • Precedence • State Fields that have a value of “any” are ignored during the search.
Configuring the switch Route Map Configuration To display the following form, go to the Route Maps Configuration form. Select a route map ID number, or open the Route Maps folder and click Add Route Map. The following table describes the Route Map Configuration controls: Table 143 Route Map Configuration controls Control Description Route Map Identifier (1-32) Assigns a numeric identifier to the route map.
Configuring the switch Route Map Access List Configuration To display the following form, go to the Route Map Configuration form. Click Add Access List. The following table describes the Access List Configuration controls: Table 144 Access List Configuration controls Control Description Access List Identifier (1-8) Assigns the access list number. Network Filter (0-256, 0=none) Sets the network filter number associated with the access list.
Configuring the switch Default Gateways Configuration To display the following form, select IP Menu > Default Gateways (click the underlined text, not the folder). This form summarizes default gateway parameters. The following table describes the Default Gateways Configuration controls: Table 145 Default Gateways Configuration controls Control Description Search Range To search for a Default Gateway, enter a range of Gateway numbers in the From and To fields.
Configuring the switch Default Gateway Configuration To display the following form, go to the Default Gateways Configuration form. Select a Default Gateway ID, or open the Default Gateways folder and click Add Default Gateway. Default Gateways are disabled by default. The following table describes the Default Gateway Configuration controls: Table 146 Default Gateway Configuration controls Control Description Default Gateway Identifier (1-4, 254) Selects a default Gateway to configure.
Configuring the switch IGMP Snooping Configuration To display the following form, select Layer 3 > IGMP > IGMP Snooping (click the underlined text, not the folder). Internet Group Management Protocol (IGMP) is used by IP Multicast routers to learn about the existence of host group members on their directly attached subnet (see RFC 2236).
Configuring the switch IGMP Snooping allows the switch to forward multicast traffic only to those ports that request it. IGMP Snooping prevents multicast traffic from being flooded to all ports. The switch learns which server hosts are interested in receiving multicast traffic, and forwards it only to ports connected to those servers.
Configuring the switch Table 147 IGMP Snooping Configuration controls Control Descriptions Snooping VLANs with Fstleave Enables or disables FastLeave processing. FastLeave allows the switch to immediately remove a port from the IGMP port list, if the host sends a Leave message, and the proper conditions are met. This command is disabled by default. Add: Adds selected VLANs to the Snooping VLANs with Fstleave list. To add a VLAN, select the VLAN in the Snooping VLANs without Fstleave list, and click Add.
Configuring the switch IGMP Filter Configuration To display the following form, go to the IGMP Filters Configuration form. Select a Filter ID, or open the IGMP Filters folder and click Add Filter. The following table describes the IGMP Filter Configuration controls: Table 148 IGMP Filter Configuration controls Control Description Filter Identifier (1 - 16) Selects an IGMP filter to configure. Enabled? Enables or disables this IGMP filter.
Configuring the switch IGMP Filtering Port Configuration To display the following form, select Layer 3 > IGMP > Switch Ports. IGMP Filtering - Port Configuration To display the following form, go to the IGMP Filtering Port Configuration form. Select a Switch Port number.
Configuring the switch The following table describes IGMP Filtering – Port Configuration controls: Table 149 IGMP Filtering - Port Configuration controls Control Description Enable/Disable Filtering on Port Enables or disables IGMP filtering on the port. IGMP Filters Available Lists the filters that you can add to the port. IGMP Filters Selected Lists the filters that have been added to the port. Select a filter number in the IGMP Filters Available list and click Add to add the filter to the port.
Configuring the switch Static Multicast Router Configuration for Port To display the following form, go to the IGMP Static Multicast Router Configuration form. Select an Mrouter Port number, or open the IGMP Static Mrouter folder and click Add Mrouter. NOTE: When you configure a static multicast router on a VLAN, the process of learning multicast routers is disabled for that VLAN.
Configuring the switch OSPF General Configuration To display the following form, select Layer 3 > OSPF Routing Protocol > General. The following table describes the OSPF General Configuration controls: Table 151 OSPF General Configuration controls Control Descriptions Globally Enable OSPF? Enables or disables OSPF. External LSDB Limit (0-2000) Sets the link state database limit. Enter zero (0) to indicate that there is no limit.
Configuring the switch OSPF MD5 Key Configuration To display the following form, go to the OSPF General Configuration form. Click Add OSPF Mdkey. The following table describes the OSPF MD5 Key Configuration controls: Table 152 OSPF MD5 Key Configuration controls Control Descriptions ID Displays a numeric identifier for the MD5 authentication key. MD5 Key Assigns a string to the MD5 authentication key.
Configuring the switch OSPF Area Configuration To display the following form, go to the OSPF Areas Configuration form. Select an area number, or open the OSPF Areas folder and click Add OSPF Area. The following table describes the OSPF Area Configuration controls: Table 153 OSPF Area Configuration controls Control Descriptions Area number (0-2) Assigns a numeric identifier for the OSPF area. Area ID Defines the area ID of the OSPF area number. Enabled? Enables or disables the OSPF area.
Configuring the switch Table 153 OSPF Area Configuration controls Control Descriptions Authentication Type? Defines the authentication method, as follows: • None: No authentication required. • Password: Authenticates simple passwords so that only trusted routing devices can participate. • MD5: This parameter is used when MD5 cryptographic authentication is required.
Configuring the switch OSPF Summary Range Configuration To display the following form, go to the OSPF Summary Ranges Configuration form. Select a summary range number, or open the OSPF Summary Ranges folder and click Add Summary Range. The following table describes the OSPF Summary Range Configuration controls: Table 154 OSPF Summary Range Configuration controls Control Descriptions Range Number (1-16) Assigns a numeric identifier to the OSPF summary range.
Configuring the switch OSPF Interfaces Configuration To display the following form, select Layer 3 > OSPF Routing Protocol > OSPF Interfaces (click the underlined text, not the folder). This form provides a summary of the state of OSPF interfaces.
Configuring the switch OSPF Interface Configuration To display the following form, go to the OSPF Interfaces Configuration form. Select an interface number, or open the OSPF Interfaces folder and click Add OSPF Interface. The following table describes the OSPF Interface Configuration controls: Table 156 OSPF Interface Configuration controls Control Descriptions IP Interface Identifier (1-250) Assigns a numeric identifier to the OSPF IP interface.
Configuring the switch Table 156 OSPF Interface Configuration controls Control Descriptions Retransmit Interval (1-3600 sec) Displays the retransmit interval in seconds. Authentication Key Sets the authentication key to clear the password. MD5 Key ID (1-255) Assigns an MD5 key to the interface. OSPF Virtual Links Configuration To display the following form, select Layer 3 > OSPF Routing Protocol > OSPF Virtual Links (click the underlined text, not the folder).
Configuring the switch OSPF Virtual Link Configuration To display the following form, go to the OSPF Virtual Links Configuration form. Select a virtual link number, or open the OSPF Virtual Links folder and click Add OSPF Virtual Link. The following table describes the OSPF Virtual Link Configuration controls: Table 157 OSPF Virtual Link Configuration controls Control Descriptions Virtual Link Identifier (1-3) Assigns a numeric identifier to the virtual link.
Configuring the switch OSPF Hosts Configuration To display the following form, select Layer 3 > OSPF Routing Protocol > OSPF Hosts (click the underlined text, not the folder).
Configuring the switch OSPF Host Configuration To display the following form, go to the OSPF Hosts Configuration form. Select a host number, or open the OSPF Hosts folder and click Add OSPF Host. The following table describes the OSPF Host Configuration controls: Table 159 OSPF Host Configuration controls Control Descriptions Host Identifier (1-128) Assigns a numeric identifier to the OSPF host. IP Address Defines the base IP address for the host entry.
Configuring the switch OSPF Route Redistribution Configuration To display the following form, select Layer 3 > OSPF Routing Protocol > OSPF Route Redistribution > Static Route Redistribution, Fixed Route Redistribution, or RIP Route Redistribution.
Configuring the switch RIP Interfaces Configuration To display the following form, select Layer 3 > Routing Information Protocol > RIP Interfaces (click the underlined text, not the folder). RIP is used for configuring Routing Information Protocol parameters. This option is turned off by default. NOTE: Do not configure RIP version 1 parameters if your routing equipment uses RIP version 2.
Configuring the switch RIP Interface Configuration To display the following form, go to the RIP Interfaces Configuration form. Select a RIP interface number, or open the RIP Interfaces folder and click Add RIP Interface. The following table describes the RIP Interface Configuration controls: Table 162 RIP Interface Configuration controls Control Descriptions IP Interface number (1-249) Assigns a numeric identifier to the RIP interface. Enable RIP? Enables or disables the RIP interface.
Configuring the switch Table 162 RIP Interface Configuration controls Control Descriptions Triggered Updates? Enables or disables Triggered Updates. Triggered Updates are used to speed convergence. When enabled, Triggered Updates force a router to send update messages immediately, even if it is not yet time for the update message. The default value is disabled. Multicast Updates? Enables or disables multicast updates of the routing table (using address 224.0.0.9). The default value is disabled.
Configuring the switch The following table describes the RIP Route Redistribution Configuration controls: Table 163 RIP Route Redistribution Configuration controls Control Descriptions Metric (1-15, 0 = none) Exports the routes of this protocol in which the metric and metric type are specified. To remove a previous configuration and stop exporting the routes of the protocol, enter 0 (none). Route Maps Available Lists the route maps that can be added to the list of OSPF static route.
Configuring the switch Virtual Routers Configuration To display the following form, select Layer 3 > Virtual Router Redundancy Protocol > Virtual Routers (click the underline text, not the folder).
Configuring the switch Virtual Router Configuration To display the following form, go to the Virtual Routers Configuration form. Select a Virtual Router number or open the Virtual Routers folder and click Add Virtual Router. The following table describes the Virtual Router Configuration controls: Table 166 Virtual Router Configuration controls Control Descriptions Virtual Router Number (1-250) Defines the virtual router number. Virtual Router Identifier (1-250) Defines the virtual router ID.
Configuring the switch Table 166 Virtual Router Configuration controls Control Descriptions IP Interface (1-249) Selects a switch IP interface. If the IP interface has the same IP address as the addr option above, this switch is considered the “owner” of the defined virtual router. An owner has a special priority of 255 (highest) and will always assume the role of master router, even if it must preempt another virtual router which has assumed master routing authority.
Configuring the switch VRRP Interfaces Configuration To display the following form, select Layer 3 > Virtual Router Redundancy Protocol > VRRP Interfaces (click the underline text, not the folder).
Configuring the switch VRRP Interface Configuration To display the following form, go to the Virtual Routers Configuration form. Select a VRRP interface number or open the VRRP Interfaces folder and click Add Virtual router Interface. The following table describes the VRRP Interface Configuration controls: Table 168 VRRP Interface Configuration controls Control Descriptions IP Interface (1-249) Defines the IP interface.
Configuring the switch VRRP General Configuration To display the following form, select Layer 3 > Virtual Router Redundancy Protocol > General. The following table describes the VRRP General Configuration controls: Table 169 VRRP General Configuration controls Control Descriptions VRRP Processing Enabled? Globally enables or disables VRRP processing.
Configuring the switch Table 169 VRRP General Configuration controls Control Descriptions Priority (1-254) Defines the election priority bias for this virtual router group. This can be any integer between 1 and 254. The default value is 100. During the master router election process, the routing device with the highest virtual router priority number wins. If there is a tie, the device with the highest IP interface address wins.
Configuring the switch Domain Name System Configuration To display the following form, select Layer 3 > Domain Name System. The Domain Name System (DNS) Menu is used for defining the primary and secondary DNS servers on your local network, and for setting the default domain name served by the switch services. DNS parameters must be configured prior to using hostname parameters with the ping, traceroute, and tftp commands.
Configuring the switch Bootstrap Protocol Relay Configuration To display the following form, select Layer 3 > Bootstrap Protocol Relay. The following table describes the Bootstrap Protocol Relay configuration controls: Table 171 Bootstrap Protocol Relay Configuration controls Control Description BOOTP Server IP Address Sets the IP address of the BOOTP server. Secondary BOOTP Server IP Address Sets the IP address of the secondary BOOTP server. BOOTP State Enables or disables the use of BOOTP.
Configuring the switch The following table describes the IP Routing General Configuration controls: Table 172 IP Routing General Configuration controls Control Description IP Forwarding Enabled? Enables or disables IP Forwarding. Enable Forwarding Directed Broadcasts? Enables or disables forwarding directed broadcasts. IP Destination Re-ARP Interval (2-120 minutes) Sets the re-ARP period in minutes.
Configuring the switch QoS Priority CoS Queue Configuration To display the following form, go to the Priority – CoS form, and select a priority value. The following table describes the CoSQ For Priority configuration controls: Table 173 CoSQ For Priority Configuration controls Control Description CoSQ (0-1) Maps the 802.1p priority of to the Class of Service queue (CoSq) priority. Enter the Class of Service queue (0-1) that handles the matching traffic.
Configuring the switch QoS CoS Queue Configuration To display the following form, go to the CoS –Weight Configuration form, and select a CoS value. The following table describes the CoSQ configuration controls: Table 174 CoSQ Configuration controls Control Description CoSq Weight (0-15) Configures the scheduling weight of the selected Class of Service queue (CoSq). QoS Switch Ports Priority Configuration To display the following form, select QoS > 802.1p > Ports Priority Table.
Configuring the switch QoS Switch Port Configuration To display the following form, go to the Switch Port Priority Configuration table, and select a port number. The following table describes the QoS switch port priority configuration controls: Table 175 QoS Switch Port Priority Configuration controls Control Description Port Priority (0-7) Configures the 802.1p priority value for the port. QoS Number of CoS Configuration To display the following form, select QoS > 802.1p > Number of CoS.
Configuring the switch ACL Configuration To display the following form, select Access Control > Access Control Lists (click the underlined text, not the folder). This form allows you to search for Access Control Lists.
Configuring the switch The following table describes the ACL Configuration controls: Table 177 ACL Configuration controls Control Description Search Range To search for an ACL, enter a range of ACL ID numbers in the From and To fields.
Configuring the switch Access Control List Configuration To display the following form, go to the ACL Configuration Table form, and select an ACL number, or open the Access Control Lists folder and click Add ACL. This form allows you to define filtering criteria for the Access Control List (ACL).The following table describes the Access Control List configuration controls: Table 178 Access Control List Configuration controls Control Description ACL ID (1-384) Assigns a numeric identifier to the ACL.
Configuring the switch Table 178 Access Control List Configuration controls Control Description Tagging Packet Format Defines the tagging format for the ACL. Source MAC Address Defines the source MAC address for this ACL. Destination MAC Address Defines the destination MAC address for this ACL. Ethernet Type Defines the Ethernet type for this ACL. VLAN ID (1-4095) Defines a VLAN number and mask for this ACL. 802.1p Priority Defines the 802.1p priority for the ACL.
Configuring the switch Table 178 Access Control List Configuration controls Control Description Statistics Enables or disables the statistics collection for the ACL. Egress Port Selects an egress port to add to the ACL. The egress port ACL will not match a Layer 2 broadcast or multicast packet. The egress port ACL will not match packets if the destination port is a trunk.
Configuring the switch ACL Re-Mark Configuration To display the following form, go to the ACL Configuration Table form, and select an ACL number, or open the Access Control Lists folder and click Add ACL. The following table describes the ACL Re-mark configuration controls: Table 180 ACL Re-mark Configuration controls Control Description Set in profile update method Defines the method used to update 802.1p priority updates, as follows: • User defined – Sets the 802.
Configuring the switch ACL Groups Configuration To display the following form, select Access Control > Access Control Groups (click the underlined text, not the folder). The following table describes the ACL Groups Configuration controls: Table 181 ACL Groups Configuration controls Control Description Search Range To search for an ACL Group, enter a range of ACL Group numbers in the From and To fields. Click Search to display ACL Groups that fit the range.
Configuring the switch Access Control Group Configuration To display the following form, go to the ACL Groups Configuration Table form, and select an ACL Group number. The following table describes the Access Control List Group configuration controls: Table 182 ACL Group Configuration controls Control Description Group ID (1-384) Assigns a numeric identifier to the ACL Group. ACLs Available Lists the ACLs that you can add to the ACL Group. You can add up to 96 ACLs to each ACL Group.
Configuring the switch Uplink Failure Detection Configuration To display the following form, select Uplink Failure Detection (click the underlined text, not the folder). Uplink Failure Detection (UFD) supports network fault tolerance in network adapter teams. Use this menu to configure a Failure Detection Pair of one Links to Monitor (LtM) group and one Links to Disable (LtD) group.
Configuring the switch Failure Detection Pair Configuration To display the following form, select Uplink Failure Detection (click the underlined text, not the folder). On the UFD Configuration form, select FDP.
Configuring the switch The following table describes the Failure Detection Pair Configuration controls: Table 184 Failure Detection Pair Configuration controls Control Description Enable/Disable FDP Enables or disables the Failover Pair. LtM Ports Available Lists the ports that can be added to the Link to Monitor (LtM). Only uplink ports (18-21) are allowed in the LtM. LtM Ports Selected Lists the ports that are members of the LtM.
Configuring the switch Table 184 Failure Detection Pair Configuration controls Control Description LtD Admin Keys Selected Lists the ports which have LACP Admin keys that are members of the LtD. Select a port in the LtD Admin Keys Available list and click Add to add the port’s Admin key to the LtD. Select a port in the LtD Admin Keys Selected list and click Remove to remove the port’s Admin key from the LtD.
