HP B-series Fabric OS 7.0.2d Release Notes (5697-2822, August 2013--includes all 7.0.x versions)

Table 16 Fabric OS 7.0.2 closed defects (continued)
SolutionClosed fixes summary
Workaround prior to upgrade: Disable
emulation.
FCIP Emulation does not release aborted exchanges, potentially causing
generated SCSI Busy status sequences if the exchange is reused within 22
seconds.
Fixed in Fabric OS 7.0.2.
Workaround prior to upgrade: Avoid
running portloopbacktest in a loop.
The HP 8/80 SAN Switch goes to a faulty status after repeated
portloopback testing on Fabric OS 7.0.1 and 7.0.1a.
Fixed in Fabric OS 7.0.2.
Fixed in Fabric OS 7.0.2.After upgrading the Brocade 8 Gbps SAN Switch for HP BladeSystem
c-Class to Fabric OS 6.4.0 (and later), the Onboard Administrator does
not report the correct IP address when using DHCP.
Fixed in Fabric OS 7.0.2.CLI response time is slow when running Fabric OS 7.x. This is noticeable
when running a script with many commands; individual command response
time is still within one second.
Workaround prior to upgrade: Remove
one of the HP 64-port 8 Gbps FC Blades
The HP SN8000B SAN Director standby CP panics after running
systemverification when it is fully populated with HP 64-port 8 Gbps
FC Blades.
and the system verification passes with no
issue.
Fixed in Fabric OS 7.0.2.
Fixed in Fabric OS 7.0.2.An abort sequence detected (IFCC) on the host console after unsolicited
status was received from an Alias Device Address during FICON emulation.
Fixed in Fabric OS 7.0.2.Various manpages were updated to add more information on the following:
1. perfaddeemonitor -force parameter
2. perfttmon/perfaddeemonitor -force, -delete -all option
3. Dport over DWDM link
4. islshow
5. fdmishow
Fixed in Fabric OS 7.0.2.FICON aborted sequences during initial online processing.
Fixed in Fabric OS 7.0.2.Allow non-FC ports to support media validated only against OEM OUI.
Fixed in Fabric OS 7.0.2.Performance is down on compressed FCIP tunnel in Fabric OS 7.0.1a
compared to Fabric OS 6.4.2a.
Workaround prior to upgrade: Either start
a multiple CCW tape write job (more than
After a tunnel bounce or slot/chassis reboot, performance is limited for
certain FICON Tape Write jobs.
1 CCW in the write chain) or a tape read
job. This corrects the peer side pool state
information.
Fixed in Fabric OS 7.0.2.
Fixed in Fabric OS 7.0.2.Port Fencing raslog message FW- 1202 FW-1501 severity level is changed
from Warning to Error. Three is no functional impact from this change.
Fixed in Fabric OS 7.0.2.After a system config default followed by a series of portcfg and
portcfgpersistentenable defaults, a few ports may remian in an FC
Disabled state.
Workaround prior to upgrade: Use the
slotstatsclear command.
In Fabric OS 7.0.1a, issuing the statsclear command returns an error
that slot0 is non-existent.
Fixed in Fabric OS 7.0.2.
Fixed in Fabric OS 7.0.2.There may be encryption/decryption issues with the HP Encryption SAN
Switch and the HP DC Switch Encryption FC Blade. If a parity error occurs
in the encryption path, frames may be transmitted to the destination carrying
an incorrect payload and without being marked with an error. If a parity
Fabric OS 7.0.2 fixes 61