Quick Start Guide A7000 dl 1xE1 + G.703 Module (J8455A) 2006-05

ManualsBrandsHP ManualsComputer AccessoriesHP 2-port E1 dl Module

Quick Start Guide 5990-8895

ProCurve Secure Router dl 1xE1 + G.703 Module

J8455A

SPECIFICATIONS

Operating

Modes

E1/FE1 Frame Relay, E1/FE1 PPP, E1/FE1 HDLC,

E1/FE1 Multilink Frame Relay, E1/FE1 Multilink PPP

E1/FE1

Interface

Supported Standards: ITU-T G.703, ITU-T G.704 (CRC-4),

ITU-T G.797, ITU-T G.823

Line Rate: 2.048 Mbps ±50 PPM

Line Code: AMI or HDB3

Framing: FAS with optional CRC-4

FE1 Line Rate: Channelized timeslot (in multiples of

56/64 kbps)

Receiver Sensitivity: -30 dB

Connector: RJ-48C

G.703 Interface Line Interface: Per ITU-T G.703

Line Rate: 2.048 Mbps, ±50 PPM

Line Code: AMI or HDB3

Framing: FAS with optional CRC-4

Receiver Sensitivity: -30 dB

Capacity: 1 to 31 timeslots

If timeslot 16 signaling is used on the G.703 interface, a

maximum of 15 timeslots can be mapped to router (1 to 15

or 17 to 31).

Connector: RJ-48C

Clock Source Network, internal, and through

Diagnostics Test Pattern Generation and Detection: QRSS, 511,

all ones, all zeros

Network loopbacks

Alarm generation and detection

Network performance data (15 minutes and 24 hours)

Compliance FCC Part 15 Class A, EN 55022 Class, EN 55024,

EN 61000-3-2, EN 61000-3-3

ACIF S016, ETSI TBR 12/TBR 13

EN60950, AS/NZS 60950

Physical Dimensions: 6.99 cm (2.75 in) W x 10.80 cm (4.25 in) D

Operating Temperature: 0°C to 50°C (32°F to 122°F)

Relative Humidity: Up to 95 percent, noncondensing

at 30°C (86°F)

Non-Operating Temperature: -20°C to 70°C (-4°F to 158°F)

Non-Operating Relative Humidity: Up to 95 percent,

noncondensing at 30°C (86°F)

Altitude: Up to 3.05 km (10,000 ft)

INSTALLATION INSTRUCTIONS

Warning

For ProCurve Secure Router modules with outside plant

connections, ensure that all cables are removed from the

module before installing or removing it from the router

chassis.

1. Remove power from the unit.

2. Slide the ProCurve Secure Router dl 1xE1 + G.703 Module into the

option slot until the module is firmly seated against the chassis.

3. Secure the screws at both edges of the module.

4. Connect the cables to the associated device(s).

5. Complete the installation of the base unit.

6. Restore power to the unit.

Note

For safety information for the routers and all modules,

please refer to the safety and ESD precautions in the

ProCurve Secure Router Installation Guide included

in your router shipment.

E1 NETWORK (RJ-48C) CONNECTION PINOUT

Pin Name Description

1 R1 Receive data from the network

2 T1 Receive data from the network

3 — Unused

4 R Transmit data toward the network

5 T Transmit data toward the network

6-8 — Unused

G.703 (RJ-48C) CONNECTION PINOUT

Pin Name Description

1 R Transmit data toward the DTE

2 T Transmit data toward the DTE

3—Unused

4 R1 Receive data from the DTE

5 T1 Receive data from the DTE

6-8 — Unused

Summary of content (2 pages)

PAGE 1
Quick Start Guide 5990-8895 ProCurve Secure Router dl 1xE1 + G.703 Module J8455A INSTALLATION INSTRUCTIONS Warning SPECIFICATIONS For ProCurve Secure Router modules with outside plant connections, ensure that all cables are removed from the module before installing or removing it from the router chassis. 1. Remove power from the unit. Operating Modes E1/FE1 Frame Relay, E1/FE1 PPP, E1/FE1 HDLC, E1/FE1 Multilink Frame Relay, E1/FE1 Multilink PPP 2. Slide the ProCurve Secure Router dl 1xE1 + G.
PAGE 2
Quick Start Guide 5990-8895 ProCurve Secure Router dl 1xE1 + G.703 Module J8455A Note An optional backup module is required for backup applications. For a description of the backup connection pinouts, refer to the Quick Start Guide included with your backup module remote-loopback Configures the interface to respond to loopbacks initiated by a remote unit (or service provider). Use the no form of this command to disable this feature. This setting is enabled by default.