Brocade Converged Enhanced Ethernet Administrator's Guide v6.1.2_cee (53-1001258-01, June 2009)
Table Of Contents
- Contents
- Figures
- Tables
- About This Document
- Introducing FCoE
- Using the CEE CLI
- In this chapter
- CEE CLI configuration guidelines and restrictions
- Using the CEE command line interface (CLI)
- CEE CLI RBAC permissions
- Accessing the CEE CLI through the console interface or through a Telnet session
- Accessing the CEE CLI from the Fabric OS shell
- Accessing CEE CLI command modes
- Using CEE CLI keyboard shortcuts
- Displaying CEE CLI commands and command syntax
- Using CEE CLI command completion
- CEE CLI command syntax conventions
- Using CEE CLI command output modifiers
- Configuring VLANs Using the CEE CLI
- In this chapter
- VLAN overview
- Ingress VLAN filtering
- VLAN configuration guidelines and restrictions
- Default VLAN configuration
- VLAN configuration procedures
- Enabling and disabling a CEE interface
- Configuring the MTU on a CEE interface
- Creating a VLAN interface
- Configuring a VLAN interface to forward FCoE traffic
- Configuring a CEE interface as a Layer 2 switch port
- Configuring a CEE interface as an access interface or a trunk interface
- Configuring VLAN classifier rules
- Configuring VLAN classifier groups
- Associating a VLAN classifier group to a CEE interface
- Clearing VLAN counter statistics
- Displaying VLAN information
- Configuring the MAC address table
- Configuring STP, RSTP, and MSTP using the CEE CLI
- In this chapter
- STP overview
- RSTP overview
- MSTP overview
- STP, RSTP, and MSTP configuration guidelines and restrictions
- Default STP, RSTP, and MSTP configuration
- STP, RSTP, and MSTP configuration procedures
- STP, RSTP, and MSTP-specific configuration procedures
- STP and RSTP-specific configuration procedures
- RSTP and MSTP-specific configuration procedures
- MSTP-specific configuration procedures
- 10-Gigabit Ethernet CEE interface-specific configuration
- Global STP, RSTP, and MSTP-related configuration procedures
- Clearing STP, RSTP, and MSTP-related information
- Displaying STP, RSTP, and MSTP-related information
- Configuring Link Aggregation using the CEE CLI
- Configuring LLDP using the CEE CLI
- Configuring ACLs using the CEE CLI
- In this chapter
- ACL overview
- Default ACL configuration
- ACL configuration guidelines and restrictions
- ACL configuration procedures
- Creating a standard MAC ACL and adding rules
- Creating an extended MAC ACL and adding rules
- Modifying a MAC ACL
- Removing a MAC ACL
- Reordering the sequence numbers in a MAC ACL
- Applying a MAC ACL to a CEE interface
- Applying a MAC ACL to a VLAN interface
- Clearing MAC ACL counters
- Displaying MAC ACL information
- Configuring QoS using the CEE CLI
- Configuring FCoE using the Fabric OS CLI
- Administering the switch
- Configuring RMON using the CEE CLI
- Index
88 Converged Enhanced Ethernet Administrator’s Guide
53-1001258-01
LLDP configuration procedures
6
Configuring the hold time for receiving devices
To configure the hold time for receiving devices, perform the following steps from the global LLDP
configuration mode:
Configuring the advertisement of optional LLDP TLVs
To configure the optional LLDP TLVs to be advertised, perform the following steps from the global
LLDP configuration mode:
Configuring the advertisement of LLDP DCBX -related TLVs
To configure the LLDP DCBX-related TLVs to be advertised, perform the following steps from the
global LLDP configuration mode:
Step Task Command
1. Configure the hold time for receiving devices. This
configures the number of consecutive LLDP hello
packets that can be missed before declaring the
neighbor information as invalid. The range is 1 to
10. The default is 4.
switch(conf-lldp)#multiplier value
2. Display the LLDP configuration. switch(conf-lldp)#do show lldp
[interface | neighbors | statistics]
Step Task Command
1. Configure the optional LLDP TLVs to be
advertised. If the advertise optional-tlv command
is entered without keywords, all optional LLDP
TLVs are advertised.
switch(conf-lldp)#advertise
optional-tlv {port-description |
system-name | system-capabilities |
system-description |
management-address}
2. Display the LLDP configuration. switch(conf-lldp)#do show lldp
[interface | neighbors | statistics]
Step Task Command
1. Configure the LLDP DCBX-related TLVs to be
advertised. By default, the dcbx-tlv is advertised;
the dot1-tlv, dot3-tlv, dcbx-fcoe-app-tlv, and
dcbx-fcoe-logical-link-tlv are not advertised.
switch(conf-lldp)#advertise
{dcbx-fcoe-app-tlv |
dcbx-fcoe-logical-link-tlv | dcbx-tlv
| dot1-tlv | dot3-tlv}
2. Display the LLDP configuration. switch(conf-lldp)#do show lldp
[interface | neighbors | statistics]