Brocade Converged Enhanced Ethernet Administrator's Guide v6.1.2_cee (53-1001258-01, June 2009)
Table Of Contents
- Contents
- Figures
- Tables
- About This Document
- Introducing FCoE
- Using the CEE CLI
- In this chapter
- CEE CLI configuration guidelines and restrictions
- Using the CEE command line interface (CLI)
- CEE CLI RBAC permissions
- Accessing the CEE CLI through the console interface or through a Telnet session
- Accessing the CEE CLI from the Fabric OS shell
- Accessing CEE CLI command modes
- Using CEE CLI keyboard shortcuts
- Displaying CEE CLI commands and command syntax
- Using CEE CLI command completion
- CEE CLI command syntax conventions
- Using CEE CLI command output modifiers
- Configuring VLANs Using the CEE CLI
- In this chapter
- VLAN overview
- Ingress VLAN filtering
- VLAN configuration guidelines and restrictions
- Default VLAN configuration
- VLAN configuration procedures
- Enabling and disabling a CEE interface
- Configuring the MTU on a CEE interface
- Creating a VLAN interface
- Configuring a VLAN interface to forward FCoE traffic
- Configuring a CEE interface as a Layer 2 switch port
- Configuring a CEE interface as an access interface or a trunk interface
- Configuring VLAN classifier rules
- Configuring VLAN classifier groups
- Associating a VLAN classifier group to a CEE interface
- Clearing VLAN counter statistics
- Displaying VLAN information
- Configuring the MAC address table
- Configuring STP, RSTP, and MSTP using the CEE CLI
- In this chapter
- STP overview
- RSTP overview
- MSTP overview
- STP, RSTP, and MSTP configuration guidelines and restrictions
- Default STP, RSTP, and MSTP configuration
- STP, RSTP, and MSTP configuration procedures
- STP, RSTP, and MSTP-specific configuration procedures
- STP and RSTP-specific configuration procedures
- RSTP and MSTP-specific configuration procedures
- MSTP-specific configuration procedures
- 10-Gigabit Ethernet CEE interface-specific configuration
- Global STP, RSTP, and MSTP-related configuration procedures
- Clearing STP, RSTP, and MSTP-related information
- Displaying STP, RSTP, and MSTP-related information
- Configuring Link Aggregation using the CEE CLI
- Configuring LLDP using the CEE CLI
- Configuring ACLs using the CEE CLI
- In this chapter
- ACL overview
- Default ACL configuration
- ACL configuration guidelines and restrictions
- ACL configuration procedures
- Creating a standard MAC ACL and adding rules
- Creating an extended MAC ACL and adding rules
- Modifying a MAC ACL
- Removing a MAC ACL
- Reordering the sequence numbers in a MAC ACL
- Applying a MAC ACL to a CEE interface
- Applying a MAC ACL to a VLAN interface
- Clearing MAC ACL counters
- Displaying MAC ACL information
- Configuring QoS using the CEE CLI
- Configuring FCoE using the Fabric OS CLI
- Administering the switch
- Configuring RMON using the CEE CLI
- Index
Converged Enhanced Ethernet Administrator’s Guide 125
53-1001258-01
FCoE configuration procedures
9
Configuring FCMAP values for a VLAN
NOTE
For information on FCMAPs, see “FCoE Initialization Protocol (FIP)” on page 11.
If the FCMAP default value is acceptable, then it can be applied to the specified VLAN. The
fcmapunset command is only necessary if the FCMAP value was previously set to a non-default
value. For example, if you reset the default value to a value other than the default value, and then
want to change the value again, you must enter the fcmapunset command to return the value to
the default value. The fcmapunset command always returns the FCMAP to the default value.
Perform the following tasks to configure FCMAP values for a VLAN:
Configuring FIP multicast advertisement intervals
NOTE
For information on the FCoE Initialization Protocol (FIP), see “FCoE Initialization Protocol (FIP)” on
page 11.
Perform the following task to configure FIP multicast advertisement intervals:
Clearing logins
Perform the following task to clear logins:
Task Command
Configure the FCMAP values for Fabric Provided
MAC Addresses (FPMA) for the specified VLANs.
Syntax is as follows:
• vid—Specifies the VLAN ID for which the
FCMAP must be set.
• fcmapid—Specifies the FCMAP to be set.
switch:admin> fcoe --fcmapset -vlan vid fcmapid
Remove the FCMAP from the specified VLAN. switch:admin> fcoe --fcmapunset -vlan vid
Task Command
Configure FIP multicast advertisement intervals.
Syntax is as follows:
• intvl—Specifies the interval in seconds. The
minimum interval value is 0 seconds and
the maximum value is 300 seconds. A value
of 0 cancels the previous advertisement
interval value.
switch:admin> fcoe --fipcfg -advintvl intvl
Task Command
Clear the logins that occurred through a front-end
port or from a device specified by the Enode's
VN_port WWN. Syntax is as follows:
• -teport slot/port—Specifies the slot or port
number.
• -device wwn—Specifies the device WWN.
switch:admin> fcoe --resetlogin -teport slot/port |
-device wwn