Comware CLI Commands in Provision Software 2013/06

ManualsBrandsHP ManualsComputer AccessoriesHP 2920 2-port 10GBASE-T Module

HP Switch Software

Comware CLI Commands in ProVision Software

K/KA.15.13

Abstract

This switch software guide is intended for network administrators and support personnel, and applies to the switch models

listed on this page unless otherwise noted. This guide does not provide information about upgrading or replacing switch

hardware. The information in this guide is subject to change without notice.

Applicable Products

HP 2615 Switches (J9565A)

HP 2620 Switches (J9623A, J9624A, J9625A, J9626A, J9627A)

HP 2910al Switches (J9145A, J9146A, J9147A, J9148A)

HP 2915 Switches (J9562A)

HP 2920 Switches (J9726A, J9727A, J9728A, J9729A)

HP 3500 Switches (J9470A, J9471A, J9472A, J9473A)

HP 3500yl Switches (J8692A, J8693A)

HP 3800 Switches (J9573A, J9574A, J9575A, J9576A, J9584A, J9585A, J9586A, J9587A, J9588A)

HP 5400zl Switches (J8697A, J8698A, J9447A, J9448A)

HP 6200yl Switch (J8992A)

HP 8200zl Switches (J9475A, J8715A/B )

HP 6600 Switches (J9263A, J9264A, J9265A, J9451A, J9452A)

HP Part Number: 5998-4399

Published: June 2013

Edition: 2

Summary of content (364 pages)

PAGE 1
HP Switch Software Comware CLI Commands in ProVision Software K/KA.15.13 Abstract This switch software guide is intended for network administrators and support personnel, and applies to the switch models listed on this page unless otherwise noted. This guide does not provide information about upgrading or replacing switch hardware. The information in this guide is subject to change without notice.
PAGE 2
© Copyright 2013 Hewlett-Packard Development Company, L.P. The information contained herein is subject to change without notice. All Rights Reserved. This document contains proprietary information, which is protected by copyright. No part of this document may be photocopied, reproduced, or translated into another language without the prior written consent of Hewlett-Packard.
PAGE 3
Contents Product Documentation.................................................................................13 About Your Switch Manual Set.................................................................................................13 Electronic Publications........................................................................................................13 1 Introduction To the ProVision CLI.................................................................
PAGE 4
display default-configuration....................................................................................................41 display device........................................................................................................................42 Field Descriptions...............................................................................................................42 display dhcp relay information all.............................................................................
PAGE 5
Field Descriptions...............................................................................................................86 Operating Notes...............................................................................................................86 display igmp group interface vlan-interface .......................................................................87 Field Descriptions..............................................................................................................
PAGE 6
Operating Notes.............................................................................................................117 display ipv6 dhcp relay statistics.............................................................................................118 Field Descriptions.............................................................................................................118 Operating Notes...........................................................................................................
PAGE 7
Operating Notes.............................................................................................................159 display mac-authentication [interface …]..................................................................................161 Operating Notes.............................................................................................................162 display memory....................................................................................................................
PAGE 8
Field Descriptions.............................................................................................................198 Operating Notes.............................................................................................................198 display ospfv3.....................................................................................................................200 Operating Notes.......................................................................................................
PAGE 9
Operating Notes.............................................................................................................237 display poe interface............................................................................................................238 Operating Notes.............................................................................................................239 display poe interface power................................................................................................
PAGE 10
Operating Notes.............................................................................................................277 display ssh server status.........................................................................................................278 Field Descriptions.............................................................................................................278 display ssh server-info................................................................................................
PAGE 11
display vrrp statistics interface vrid .........................................319 display vrrp verbose..............................................................................................................320 3 Fundamental Commands.........................................................................322 backup startup-configuration..................................................................................................322 Operating Notes.............
PAGE 12
Operating Notes.............................................................................................................348 telnet..................................................................................................................................349 Operating Notes.............................................................................................................349 telnet ipv6.........................................................................................................
PAGE 13
Product Documentation About Your Switch Manual Set NOTE: For the latest version of all HP switch documentation, including Release Notes covering recently added features, please visit the HP Networking web site at www.hp.com/Networking/ support. Electronic Publications The latest version of each of the publications listed below is available in PDF format on the HP Networking web site, as described in the Note at the top of this page.
PAGE 14
1 Introduction To the ProVision CLI Comware Command Support in ProVision Software The selected Comware CLI commands described in this guide are included in the ProVision software CLI to help Comware-experienced network management staff learn to use the ProVision software CLI with a minimum of effort. This edition of Comware CLI Commands in ProVision Software describes the operation and output of selected Comware display commands added to the ProVision software.
PAGE 15
mld ospf ospfv3 schedule snmp-agent HP Switch> display MLD status and configuration information.
PAGE 16
CLI Operation Comparing Comware and ProVision Commands Comware display commands and ProVision software show commands produce status information used for monitoring, troubleshooting, and auditing the switch network environment and configuration. • Like show commands, using display commands does not change the switch operating mode. • Comware display commands are additional commands supported in ProVision software, and do not replace any existing ProVision commands.
PAGE 17
Use exit to return to the next-highest context level. Listing Commands Available at Any Context Level. At a given context level you can list and execute the commands that level offers, plus all of the commands available at preceding levels. To list available commands, use the [?] key. For example: HP Switch# show vlans ? custom Show vlan parameters in customized order. ports Show VLANs that have at least one port from the 'PORT-LIST' as a member.
PAGE 18
2 Display Commands display acl | name > Comware Related Provision display acl | name > show access-list Displays configuration and match statistics for the specified or all IPv4 ACLs. This command displays ACL rules in config or depth-first order, whichever is configured. HP Switch# display acl 2001 Basic ACL 2001, named -flow-, 2 rules, Statistics enabled ACL's step is 5 rule 1 permit source 1.1.1.
PAGE 19
10 Action: deny IP : 0.0.0.0 Mask: 255.255.255.255 20 Action: permit IP : 1.2.3.4 Mask: 0.0.0.255 display arp Comware Related Provision display arp show arp Displays ARP (Address Resolution Protocol) configuration information. HP Switch(config)# display arp Type: S-Static D-Dynamic L-Local I-Invalid IP Address MAC Address VLAN ID Interface 120.85.204.1 002347-bbd940 1 1 n/a O-Other Aging Type D Field Descriptions IP Address: IP address in an ARP entry.
PAGE 20
display arp Field Mappings.
PAGE 21
display arp Comware Related ProVision display arp show arp Displays ARP entries in the ARP mapping table. If no parameter is specified, all ARP entries are displayed. HP Switch# display arp 20.1.1.1 IP Address 20.1.1.1 Type: S-Static MAC Address 002347-bbd940 D-Dynamic L-Local VLAN ID Interface 1 1 I-Invalid O-Other Aging Type n/a D Field Descriptions IP Address: IP address in an ARP entry. MAC Address: MAC address in an ARP entry.
PAGE 22
display arp detection Comware Related ProVision display arp detection show arp-protect Displays arp-protected VLANs. HP Switch# display arp detection ARP detection is enabled in the following VLANs: 1-100 Example of Related ProVision Software Command Output. HP Switch# show arp-protect ARP Protection Information Enabled Vlans : 1-4094 Validate : dest-mac, src-mac Port Trust ----- ----B1 Yes B2 Yes B3 No B4 No B5 No For more information, see the latest Access Security Guide for your switch.
PAGE 23
display arp detection statistics Comware Related ProVision display arp detection statistics show arp-protection statistics Displays the statistics of the detected arp.
PAGE 24
display arp ip-address Comware Related ProVision display arp ip-address show arp Displays the ARP entry for a specified IP address. HP Switch# display arp 20.1.1.1 Type: S-Static IP Address 20.1.1.1 D-Dynamic MAC Address 002347-bbd940 L-Local VLAN ID 1 I-Invalid O-Other Interface Aging Type 1 n/a D Example of Related ProVision Software Command Output. HP Switch# show IP ARP table IP Address --------------15.255.128.1 15.255.131.19 15.255.133.
PAGE 25
display boot-loader Comware Related ProVision display boot-loader show flash Displays the current flash memory precedence and the source of the current boot file (software image). The switch has two flash memory locations: primary and secondary. In the display boot-loader output: • btm.swi is the primary flash memory. • secondary.swi is the secondary flash memory.
PAGE 26
HP Switch# show flash Image Size (bytes) Date Version ----------------- ------------ -------- -------------Primary Image : Secondary Image : 14995368 12/20/11 K.15.07.0003 14995368 12/20/11 K.15.08.0001 Boot ROM Version : K.15.26 Default Boot : Primary Boot-Loader Field Mappings. 26 Comware ProVision software btm.swi Primary Image secondary.
PAGE 27
display clock Comware Related ProVision display clock show time show system information Displays the current time, time zone, day, and date setting on the switch. HP Switch# display clock 16:07:27 GMT Mon 03/16/2012 Field Descriptions: Time: Current time in HH:MM:SS format on the switch. Time Zone: GMT (default) or the configured time zone.
PAGE 28
display command-alias Comware Related ProVision display command-alias show alias Displays any defined command aliases and their corresponding command assignments configured on the switch.
PAGE 29
display counters Comware Related ProVision display clock show interface Displays traffic statistics for interfaces. HP Switch# display counters inbound interface Interface Total(pkts) Broadcast(pkts) Multicast(pkts) Err(pkts) A1 11 2 5 0 A2 0 0 0 0 A3 0 0 0 0 A4 0 0 0 0 A5 0 0 0 0 A6 0 0 0 0 A7 0 0 0 0 . . . HP Switch# display counters outbound interface Interface Total(pkts) Broadcast(pkts) Multicast(pkts) Err(pkts) A1 13 6 6 0 A2 0 0 0 0 A3 0 0 0 0 A4 0 0 0 0 A5 0 0 0 0 A6 0 0 0 0 A7 0 0 0 0 .
PAGE 30
Example of Related ProVision Software Command Output. HP Switch(config)# show interface a1 Status and Counters - Port Counters for port A1 Name : O’Connor@10.25.101.
PAGE 31
display counters rate Comware Related ProVision display counters rate show int Displays traffic rate statistics over the last 300 seconds. The statistics cover only interfaces in up state. HP Switch# display counters rate outbound interface Interface Total(pkts/sec) Broadcast(pkts/sec) Multicast(pkts/sec) A1 84 0 42 A2 0 0 0 Overflow: n/a --: not supported.
PAGE 32
display cpu-usage Comware Related ProVision display cpu-usage show cpu [slot [] | ] Displays average CPU usage statistics for 5 seconds, 1 minute and 5 minutes. HP Switch# display cpu-usage Master CPU usage: 6% in last 5 seconds 4% in last 1 minute 3% in last 5 minutes Example of Related ProVision Software Command Output.
PAGE 33
display cpu-usage history Comware Related ProVision display cpu-usage history No equivalent ProVision software command Displays the history CPU utilization rates in a coordinate plane. The system collects the statistics of history CPU utilization rates at a certain interval and saves the statistics in the history record area. You can use the this command to display the history CPU utilization rates in the last 5 minutes. The history CPU utilization rates are displayed through x and y coordinates.
PAGE 34
display current-configuration Comware Related ProVision display current-configuration show running-configuration Displays the current configuration. HP Switch# display current-configuration J8697A Configuration Editor; Created on release #K.15.09.0000x Ver #03:01.1f.
PAGE 35
display current-configuration by-linenum Comware Related ProVision display current-configuration by-linenum show running-configuration Displays the number of each line. HP Switch# display current-configuration by-linenum 1: J8697A Configuration Editor; Created on release #K.15.09.0000x 2: Ver #03:01.1f.
PAGE 36
display current-configuration configuration Comware Related ProVision display current-configuration configuration No equivalent ProVision software command Displays active configuration in the system excluding vlan and interface configuration. This command is available only in manager mode. HP Switch# display current-configuration configuration hostname "HP-6200yl-24G" module 1 type J8992A alias "view" "show" banner motd "\n" radius-server host 10.10.10.
PAGE 37
display current-configuration interface Comware Related ProVision display current-configuration interface show running-configuration Displays the interface configuration.
PAGE 38
untagged vlan 1 exit interface A18 untagged vlan 1 exit interface A19 untagged vlan 1 Example of Related ProVision Software Command Output. HP Switch# show running-config Running configuration: ; J9087A Configuration Editor; Created on release #R.11.XX hostname "Switch" snmp-server community "public" Unrestricted snmp-server host 15.255.133.236 "public" snmp-server host 15.255.133.222 "public" snmp-server host 15.255.133.70 "public" snmp-server host 15.255.134.
PAGE 39
display debugging Comware Related ProVision display debugging [ option ] show debug [buffer [-c < count > | -r | option-str ]] Displays the options from any of the following lists that have debug logging enabled. acl distributed-trunking ip lldp snmp arp-protect dynamic-ip-lockdown ipv6 policy vrrp cdp event lacp security Using display debugging without specifying an option lists all options in the set that are enabled for debug logging.
PAGE 40
Debug Field Mappings.
PAGE 41
display default-configuration Comware Related ProVision display default-configuration No equivalent ProVision software command Displays factory defaults of the switch, and all commands to be executed when the switch boots with the factory defaults. HP Switch# display default-configuration ; J8693A Configuration Editor; Created on release #K.15.09.0000x ; Ver #03:01.1f.ef:f2 vlan 1 name "DEFAULT_VLAN" ip address dhcp-bootp exit Minimum Software Version: 15.10.
PAGE 42
display device Displays the global enable/disable state of GVRP. Comware Related ProVision display device No equivalent ProVision software command Displays physical modules present in the switch. This command also identifies the status of these modules, whether they are up/active/standby or failed etc. HP Switch# display device SlotNo. Brd Type BrdStatus SubSlotNum MM1 HP J9092A Management Modul... Standby n/a MM2 HP J9092A Management Modul... Active n/a SSM HP J9095A System Support M...
PAGE 43
display dhcp relay information all Comware Related ProVision display dhcp relay information all No equivalent ProVision software command Displays option 82 configuration information on the DHCP relay agent.
PAGE 44
display dhcp relay information interface Vlan-interface Comware Related ProVision display dhcp relay information interface Vlan-interface No equivalent ProVision software command Displays option 82 configuration information on the DHCP relay agent based on vlan.
PAGE 45
display dhcp relay statistics Comware Related ProVision display dhcp relay statistics show dhcp-relay Displays DHCP packet statistics related to a specified or all DHCP server groups. DHCP relay statistics identifies the UDPF_DHCP_MSG PDUs and provides the information regarding the number and type of PDUs being received/relayed from/to client and server. It also distinguishes the type of packets (DISCOVER, REQUEST, INFORM, DECLINE, RELEASE, BOOTPREQUEST, OFFER, ACK, NAK) along with bad packets.
PAGE 46
HP Switch# display dhcp relay statistics Bad packets received: 0 DHCP packets received from clients: 2 DHCPDISCOVER packets received: 1 DHCPREQUEST packets received: 1 DHCPINFORM packets received: 0 DHCPRELEASE packets received: 0 DHCPDECLINE packets received: 0 BOOTPREQUEST packets received: 0 DHCP packets received from servers: 2 DHCPOFFER packets received: 1 DHCPACK packets received: 1 DHCPNAK packets received: 0 BOOTPREPLY packets received: 0 DHCP packets relayed to servers: 2 DHCPDISCOVER packets relay
PAGE 47
• • • • ◦ DHCPNAK packets received ◦ BOOTPREPLY packets received DHCP packets relayed to servers: ◦ DHCPDISCOVER packets relayed ◦ DHCPREQUEST packets relayed ◦ DHCPINFORM packets relayed ◦ DHCPRELEASE packets relayed ◦ DHCPDECLINE packets relayed ◦ BOOTPREQUEST packets relayed DHCP packets relayed to clients: ◦ DHCPOFFER packets relayed0 ◦ DHCPACK packets relayed ◦ DHCPNAK packets relayed ◦ BOOTPREPLY packets relayed DHCP packets sent to servers: ◦ DHCPDISCOVER packets sent
PAGE 48
Option 82 handle policy Remote ID : mac : replace DHCP Relay Statistics: Client Requests Server Responses Valid Dropped Valid Dropped ---------- ---------- ---------- ---------0 0 0 0 DHCP Relay Option 82 Statistics: Client Requests Server Responses Valid Dropped Valid Dropped ---------- ---------- ---------- ---------0 0 0 0 display dhcp relay statistics Field Mappings. The Comware output does not correlate to the ProVision output.
PAGE 49
display dhcp-snooping [ip ip_address] Comware Related ProVision display dhcp-snooping [ip ip_address] show dhcp-snooping binding Displays the user IP-MAC address mapping entries recorded by the DHCP snooping function. HP Switch# display dhcp-snooping DHCP Snooping is enabled. The client binding table for all untrusted ports. Type : D--Dynamic , S--Static , R--Recovering Type IP Address MAC Address Lease VLAN SVLAN Interface ---- ----------- --------------- ---------- ---- ----- --------S 192.168.1.
PAGE 50
display dhcp-snooping binding database Comware Related ProVision display dhcp-snooping binding database show dhcp-snooping Displays the DHCP snooping binding file information. HP Switch# display dhcp-snooping binding database File name : cfa0:/database.dhcp Update interval : 10 minutes Latest read time : n/a Latest write time : Jul 15 2008 16:38:24 Status : Last write succeeded. Example of Related ProVision Software Command Output.
PAGE 51
display dhcp-snooping information Comware Related ProVision display dhcp-snooping information show dhcp-snooping Displays information about dhcp snooping when option 82 is enabled. HP Switch# display dhcp-snooping information all Interface: A1 Status: Enable Strategy: Drop Format: n/a Remote ID format-type: HEX User defined : Remote ID: 0026f1-0faf00 Interface: A2 Status: Enable Strategy: Drop Format: n/a Remote ID format-type: HEX User defined: Remote ID: 0026f1-0faf00 ... (contd.
PAGE 52
display dhcp-snooping packet statistics Comware Related ProVision display dhcp-snooping packet statistics show dhcp-snooping statistics Displays the statistics of the dhcp snooping packets. HP Switch# display dhcp-snooping packet DHCP packets received DHCP packets send Packets dropped due to rate limitation Dropped invalid packets statistics : 2 : 0 : n/a : 0 Example of Related ProVision Software Command Output.
PAGE 53
display dhcp-snooping trust Comware Related ProVision display dhcp-snooping trust show dhcp-snooping Displays information about trusted ports. HP Switch(config)# display dhcp-snooping trust DHCP Snooping is enabled. DHCP Snooping trust becomes active. Interface Trusted ========================= ============ A1 Trusted A2 Trusted A3 Trusted A4 Trusted Field Descriptions Interface: Interface Trusted: The interface is trusted or not trusted.
PAGE 54
display diagnostic-information Comware Related ProVision display diagnostic-information show tech Displays different levels of diagnostic information. This is an alias to the ProVision command show tech and shares the same behavior. HP Switch# show tech show system Status System System System and Counters - General System Information Name : 5400_1 Contact : Location : MAC Age Time (sec) : 300 Time Zone : 0 Daylight Time Rule : None Software revision ROM Version : K.14.XX : K.12.
PAGE 55
display dns < domain | server > Comware Related ProVision display dns < domain | server > show ip dns show ip Displays the current IPv4 DNS domain name suffixes and server configuration. HP Switch# display dns domain Type: D:Dynamic No. 1 S:Static Type S Domain-name atlantic.widgetcorp.net HP Switch# display dns server Type: D:Dynamic DNS Server 1 2 S:Static Type S S IP Address 10.110.34.51 10.110.34.101 Field Descriptions No.: Sequence number. Type: Shows the type of domain name suffix.
PAGE 56
1. 2. 16.110.135.52 16.110.135.51 DNS Field Mappings. 56 Comware ProVision Software No.
PAGE 57
display dns domain Comware Related ProVision display dns domain show ip dns Displays all the domain name suffixes that are appended to host names by the resolver before sending the queries to name servers. These domain name suffixes could have been statically configured on the switch or obtained from the DHCP server dynamically. HP Switch# display dns domain Type: D:Dynamic S:Static No. 1 2 3 Type S S S Domain-name hp5.com hp.in hp.us Example of Related ProVision Software Command Output.
PAGE 58
display dns domain dynamic Comware Related ProVision display dns domain dynamic No equivalent ProVision software command Displays all the domain name suffixes that are obtained from the DHCP server dynamically. HP Switch# display dns domain dynamic Type: D:Dynamic No. 1 2 3 Type D D D S:Static Domain-name hp2.net hp3.net hp4.net Minimum Software Version: 15.10.
PAGE 59
display dns ipv6 server Comware Related ProVision display dns ipv6 server show ip dns Displays IPv6 DNS server information. HP Switch# display dns ipv6 server Type: D:Dynamic S:Static DNS Server Type IPv6 Address (Interface Name) 1 S 1::1 2 S FE80:1111:2222:3333:4444:5555:6666:7777 Vlan2 Field Descriptions DNS Server: Sequence number of the DNS server, which is assigned automatically by the system, starting from 1. Type: Type of the DNS server.
PAGE 60
Example of Related ProVision Software Command Output. HP Switch(config)# show ip dns DNS Mode : Manual Domain Suffix : atlantic.widgetcorp.net DNS Servers Configured: ---------------------Priority DNS Server Addresses --------------------------1. 10.110.34.51 2. 10.110.34.101 display dns ipv6 server Field Mappings.
PAGE 61
display dot1x [interface …]display dot1x sessions [interface …]display dot1x statistics [interface …] Comware Related ProVision display dot1x [interface ...] show dhcp-snooping binding display dot1x sessions [interface ...] display dot1x statistics [interface ...] Displays information about 802.1X. HP Switch# display dot1x Equipment 802.
PAGE 62
Handshake is n/a Handshake secure is n/a 802.1X unicast-trigger is n/a Controlled User(s) amount to n/a A2 is link-down 802.1X protocol is disabled Proxy trap checker is n/a Proxy logoff checker is n/a Handshake is n/a Handshake secure is n/a 802.1X unicast-trigger is n/a Controlled User(s) amount to n/a A3 is link-down 802.1X protocol is disabled Proxy trap checker is n/a Proxy logoff checker is n/a Handshake is n/a Handshake secure is n/a 802.
PAGE 63
MacAddress IP VLAN Interface Time left ----------------- -------- ----- --------- --------22.22.22.22.22.22 10.0.0.1 4 B2 1600 Operating Notes For more information, refer to the latest Access Security Guide for your switch. Minimum Software Version: 15.10.
PAGE 64
display dot1x [interface] Comware Related ProVision display dot1x [interface interface-list] show port-access authenticator [config| statistics | session counters] display dot1x sessions [interface interface-list] display dot1x statistics [interface interface-list] Displays information about 802.1X. If you specify neither the sessions keyword nor the statistics keyword, the command displays all information about 802.1X, including session information, statistics, and configurations.
PAGE 65
HP Switch(config)# display dot1x interface A1 Equipment 802.1X protocol is CHAP authentication is n/a Proxy trap checker is n/a Proxy logoff checker is n/a EAD quick deploy is n/a Configuration: Transmit Period 30 s, Handshake Period n/a Quiet Period 60 s, Quiet Period Timer is n/a Supp Timeout 30 s, Server Timeout 300 s Reauth Period 3600 s The maximal retransmitting times 2 EAD quick deploy configuration: EAD timeout: n/a The maximum 802.1X user resource number is n/a per slot Total current used 802.
PAGE 66
HP Switch(config)# display dot1x sessions Equipment 802.1X protocol is enabled CHAP authentication is n/a The maximum 802.1X user resource number is n/a per slot Total current used 802.1X resource number is n/a A1 is link-up 802.1X protocol is disabled Proxy trap checker is n/a Proxy logoff checker is n/a Handshake is n/a Handshake secure is n/a 802.1X unicast-trigger is n/a Controlled User(s) amount to n/a A2 is link-down 802.
PAGE 67
HP Switch(config)# display dot1x statistics Equipment 802.1X protocol is enabled CHAP authentication is n/a The maximum 802.1X user resource number is n/a per slot Total current used 802.1X resource number is n/a A1 is link-up 802.1X protocol is disabled Proxy trap checker is n/a Proxy logoff checker is n/a Handshake is n/a Handshake secure is n/a 802.
PAGE 68
The maximal retransmitting times: Maximum number of attempts for sending an authentication request to a client. The maximum 802.1X user resource number per slot: Maximum number of concurrent 802.1X user per card. Total current used 802.1X resource number: Total number of online 802.1X users. GigabitEthernet3/0/1 is link-up: Status of the port. In this example, GigabitEthernet 3/0/1 is up. 802.1X protocol is disabled: Specifies whether 802.1X is enabled on the port.
PAGE 69
Port ---1 2 ... | | + | | Re-auth Period ------No No Access Control -------Auto Auto Max Reqs ----2 2 Quiet Period ------60 60 TX Timeout -------30 30 Supplicant Timeout ---------30 30 Server Timeout -------30 30 Cntrl Dir ----both in HP Switch(config)# show port-access authenticator session-counters Port Access Authenticator Session Counters Port-access authenticator activated [No] : Yes Allow RADIUS-assigned dynamic (GVRP) VLANs [No] : No Session Session Port Frames In Frames Out Time(sec.
PAGE 70
HP Switch(config)# show port-access authenticator statistics Port Access Authenticator Statistics Port-access authenticator activated [No] : Yes Allow RADIUS-assigned dynamic (GVRP) VLANs [No] : No Source Port MAC address ---- ------------2 001560-b3ea48 TX ReqId -----1 TX Req ----0 RX Start -----0 RX Logoff ------0 RX RespId ------0 RX Resp ----0 RX Errors ------0 display dot1x Field Mappings. 70 Comware ProVision Software Equipment 802.
PAGE 71
Comware ProVision Software Fail Packets n/a Received EAPOL Start Packets RX Start EAPOL Logoff Packets RX Logoff EAP Response/Identity Packets RX RespId EAP Response/Challenge Packets RX Resp Error Packets RX Errors Controlled User(s) amount n/a display dot1x [interface] 71
PAGE 72
display environment Comware Related ProVision display environment show system temperature Displays the temperature information, including the current temperature and temperature thresholds of cards.
PAGE 73
display fan Comware Related ProVision display fan show system fans Displays the operating state of built-in fans. HP Switch# display fan Fan 1 State: Fan Ok Example of Related ProVision Software Command Output. HP Switch(config)# show system fans Fan Information Num | State | Failures -------+-------------+---------Sys-1 | Fan OK | 0 0 / 1 Fans in Failure State 0 / 1 Fans have been in Failure State Operating Notes ProVision uses HP format for printing the fan state.
PAGE 74
display fib Comware Related ProVision display fib show ip route Displays FIB entries that match the specified destination IP address. If no mask or mask length is specified, the FIB entry that matches the destination IP address and has the longest mask will be displayed; if the mask is specified, the FIB entry that exactly matches the specified destination IP address will be displayed.
PAGE 75
HP Switch(config)# show ip route IP Route Entries Destination Gateway VLAN Type Sub-Type Metric Dist. ----------------- --------------- ---- --------- ---------- -------- ----10.10.10.1/32 10.10.12.
PAGE 76
display fips status Comware Related ProVision display fips status show secure-mode NOTE: This command is not supported on the HP 2920 Series switches. Displays FIPS state. By default, the FIPS mode is disabled. HP Switch# display fips status FIPS mode is disabled or HP Switch# display fips status FIPS mode is enabled Example of Related ProVision Software Command Output.
PAGE 77
display garp statistics interface Comware Related ProVision display garp statistics interface show gvrp Displays GVRP transmitted, received and discarded frames in a specified VLAN on a port. HP Switch# display garp statistics interface a2 GARP statistics on port A2 Number of GVRP Frames Received : 79 Number of GVRP Frames Transmitted : 67 Number of Frames Discarded : 0 Example of Related ProVision Software Command Output.
PAGE 78
display garp timer interface Comware Related ProVision display garp timer interface show gvrp Display GARP timer in a specified port. HP Switch# display garp timer interface a2 GARP timers on port A2 Garp Join Time : 20 centisecounds Garp Leave Time : 300 centisecounds Garp LeaveAll Time : 1000 centisecounds Garp Hold Time : (n/a) Example of Related ProVision Software Command Output.
PAGE 79
display gvrp state interface vlan Comware Related ProVision display gvrp state interface vlan show gvrp Displays GVRP state machines in a specified VLAN on a port. HP Switch# display gvrp state interface a2 vlan 2 GVRP state of VLAN 2 on port a2 Applicant state machine : QA Registrar state machine : MTR Field Descriptions Applicant state machine: The Applicant state machine handles attribute declarations.
PAGE 80
display gvrp statistics Comware Related ProVision display gvrp statistics show gvrp Displays the GVRP statistics of all tagged ports.
PAGE 81
display gvrp status Displays the global enable/disable state of GVRP. Comware Related ProVision display gvrp status show gvrp HP Switch# display gvrp status GVRP is enabled Operating Notes To enable and control GVRP operation in ProVision software, use the following commands: gvrp interface < port-list > unknown-vlans < learn | block | disable > ProVision software also supports GVRP configuration and status monitoring by using the Menu interface.
PAGE 82
display gvrp vlan-operation interface interface-type interface-number Comware Related ProVision display gvrp vlan-operation interface interface-type interface-number No equivalent ProVision software command Displays information about dynamic VLAN operations on a port.
PAGE 83
display history-command Comware Related ProVision display history-command show history Displays the last 25 commands executed on the switch CLI, including commands entered incorrectly. The command listing begins with the oldest command in the sequence and ends with the most recent command executed (excluding the display history-command itself).
PAGE 84
display hwtacacs Comware Related ProVision display hwtacacs show tacacs Displays the configuration information or statistics of HWTACACS schemes. This command is available only in manager mode. HP Switch# display hwtacacs ------------------------------------------------------------HWTACACS-server template name : n/a Primary-authentication-server : 1.2.3.4:n/a VPN instance : n/a Primary-authorization-server : 1.2.3.4:n/a VPN instance : n/a Primary-accounting-server : 1.2.3.
PAGE 85
Example of Related ProVision Software Command Output. HP Switch# show tacacs Status and Counters - TACACS Information Timeout : 5 Source IP Selection : Configured IP Interface Encryption Key : Operating Notes For more information, refer to the latest Basic Operation Guide for your switch. Minimum Software Version: 15.10.
PAGE 86
display igmp group Comware Related ProVision display igmp group show ip igmp groups Displays IGMP group address, uptime, and expiry information. If no IGMP groups are detected, returns the system prompt. HP Switch# display igmp group Total 1 IGMP Group(s). Interface group report information Vlan-interface1(15.255.134.111): Total 1 IGMP Group reported Group Address Last Reporter UpTime Expires 10.255.215.190 10.125.103.
PAGE 87
display igmp group interface vlan-interface Comware Related ProVision display igmp group interface vlan-interface show ip igmp vlan Displays information about dynamically joined IGMP multicast groups. HP Switch# display igmp group interface vlan-interface 30 Vlan-interface30(75.1.30.1): Total 5 IGMP Groups reported Group Address Last Reporter UpTime Expires 239.1.1.1 75.1.30.10 5d 17:48:41 00:03:13 239.1.1.2 75.1.30.10 5d 17:48:41 00:03:13 239.1.1.3 75.1.30.10 5d 17:48:41 00:03:13 239.
PAGE 88
display igmp group interface vlan-interface static Comware Related ProVision display igmp group interface vlan-interface static No equivalent ProVision software command Displays information regarding statically joined IGMP multicast groups. HP Switch# display igmp group interface Vlan-interface 400 static Static join group information of VPN-Instance: public net Total 21 entries Total 6 entries matched Group Address 225.1.4.6 239.4.4.1 239.4.4.2 239.4.4.3 239.4.4.4 239.4.5.6 Source Address 0.
PAGE 89
display igmp group interface vlan-interface verbose Comware Related ProVision display igmp group interface vlan-interface verbose No equivalent ProVision software command Displays detailed information about IGMP multicast groups in a particular interface. HP Switch# display igmp group interface Vlan-interface 400 verbose Vlan-interface400(192.168.9.2): Total 5 IGMP Groups reported Group: 225.1.5.4 Uptime: 00:07:19 Expires: 00:01:43 Last reporter: 192.168.9.
PAGE 90
display igmp group port-info Comware Related ProVision display igmp group port-info vlan show ip igmp vlan Displays Layer 2 port information of IGMP groups, including both dynamic and static Layer 2 port entries. HP Switch# display igmp group port-info vlan 5 Total 2 IP Group(s). Total n/a IP Source(s). Total n/a MAC Group(s). Port flags: D-Dynamic port, S-Static port, C-Copy port Subvlan flags: R-Real VLAN, C-Copy VLAN Vlan(id):5. Total 2 IP Group(s). Total n/a IP Source(s).
PAGE 91
of the card with chassis chassis-number slot slot-number. For an aggregation port, you do not need to do this. Operating Notes Since ProVision switches do not need anything to be configured globally to enable igmp, no error message is displayed for a display command if igmp is not enabled. For more information on IGMP operation, see the "Multimedia Traffic Control with IP Multicast (IGMP)" chapter in the latest Advanced Traffic Management Guide for your switch.
PAGE 92
display igmp group static Comware Related ProVision display igmp group static show ip igmp vlan Displays the information regarding statically joined IGMP multicast groups. HP Switch# display igmp group static Static join group information Total 19 entries Group Address 225.1.1.1 225.1.1.5 225.1.4.1 225.1.5.4 225.4.4.1 225.4.4.2 225.4.4.3 225.4.4.4 225.5.5.1 225.5.5.2 225.5.5.3 225.5.5.4 225.5.5.5 225.44.46.46 225.44.46.46 225.44.46.46 225.145.145.145 225.145.145.145 225.145.145.
PAGE 93
display igmp group verbose Comware Related ProVision display igmp group verbose No equivalent ProVision software command Displays detailed information about IGMP multicast groups. HP Switch# display igmp group verbose Interface group report information Vlan-interface400(192.168.9.2): Total 5 IGMP Groups reported Group: 225.1.5.4 Uptime: 00:00:16 Expires: 00:01:54 Last reporter: 192.168.9.9 Last-member-query-counter: 0 Last-member-query-timer-expiry: off Version1-host-present-timer-expiry: Group: 239.4.
PAGE 94
display igmp group x.x.x.x static Comware Related ProVision display igmp group x.x.x.x static show ip igmp vlan Displays information regarding statically joined IGMP multicast groups. HP Switch# display igmp group 225.44.46.46 static Static join group information Total 19 entries Total 3 entries matched Group Address 225.44.46.46 225.44.46.46 225.44.46.46 Source Address 0.0.0.0 0.0.0.0 0.0.0.
PAGE 95
display igmp group x.x.x.x verbose Comware Related ProVision display igmp group x.x.x.x verbose No equivalent ProVision software command Displays detailed information about a specified IGMP multicast group. HP Switch# display igmp group 239.4.4.4 verbose Interface group report information Vlan-interface400(192.168.9.2): Total 5 IGMP Groups reported Group: 239.4.4.4 Uptime: 00:01:56 Expires: 00:02:06 Last reporter: 192.168.9.
PAGE 96
display igmp interface Comware Related ProVision display igmp interface show ip igmp vlan Displays IGMP configuration and operation information of the specified interface or all IGMP-enabled interfaces. HP Switch# display igmp interface Interface information Vlan-interface30(75.1.30.
PAGE 97
Version2-querier-present-timer-expiry: Remaining time of the IGMPv2 querier present timer, where "off" means that the timer never expires Example of Related ProVision Software Command Output. There is no direct equivalent ProVision command.
PAGE 98
display igmp interface verbose Comware Related ProVision display igmp interface verbose No equivalent ProVision software command Displays detailed IGMP configuration and operation information. HP Switch# display igmp interface verbose Interface information Vlan-interface1(10.100.239.
PAGE 99
display igmp interface vlan-interface Comware Related ProVision display igmp interface vlan-interface show ip igmp vlan Displays the IGMP configuration and operation information of the specified interface or all IGMP-enabled interfaces. HP Switch# display igmp interface vlan-interface 1 Vlan-interface1(10.100.1.
PAGE 100
display igmp interface vlan-interface Field Mappings.
PAGE 101
display igmp routing-table Comware Related ProVision display igmp routing-table show ip igmp vlan Displays information regarding the IGMP routing table. HP Switch# display igmp routing-table Routing table Total 5 entries 00001. (*, 239.1.1.1) List of 1 downstream interface Vlan-interface30 (75.1.30.1), Protocol: IGMP 00002. (*, 239.1.1.2) List of 1 downstream interface Vlan-interface30 (75.1.30.1), Protocol: IGMP 00003. (*, 239.1.1.3) List of 1 downstream interface Vlan-interface30 (75.1.30.
PAGE 102
display interface Comware Related ProVision display interface show interface Displays current state about a specified port and related information. If no port number is specified, information is displayed for all ports.
PAGE 103
B4 B5 B6 100/1000T | No 100/1000T | No 100/1000T | No Yes Yes Yes Down 1000FDx Down 1000FDx Down 1000FDx Auto off 0 Auto off 0 Auto off 0 Operating Notes For more information, refer to the latest Management and Configuration Guide for your switch. Minimum Software Version: 15.10.
PAGE 104
display interface brief Comware Related ProVision display interface brief show interfaces brief NOTE: This command is not supported on the HP 2920 Series switches. Displays brief information about Layer 3 interfaces (tunnels) and Layer 2 interfaces. HP Switch(config)# display interface brief The brief information of interface(s) under route mode: Link: ADM - administratively down; Stby - standby Protocol: (s) - spoofing Interface Link Protocol Main IP Description tunnel-1 Down UP 20.1.1.
PAGE 105
PVID: The default VLAN ID. Description: Name of the interface. Operating Notes For more information on interface statistics, see the "Port Status and Configuration" chapter in the latest Management and Configuration Guide for your switch. Example of Related ProVision Software Command Output.
PAGE 106
display interface brief down Comware Related ProVision display interface brief down show interfaces brief Displays information about interfaces in down state and the relevant causes.
PAGE 107
A1 A2 A3 A4 A5 A6 A7 A8 10GbE-T 10GbE-T 10GbE-T 10GbE-T 10GbE-T 10GbE-T 10GbE-T 10GbE-T | | | | | | | | No No No No No No No No Yes Yes Yes Yes Yes Yes Yes Yes Up Down Down Down Down Down Down Down 1000FDx 10GigFD 10GigFD 10GigFD 10GigFD 10GigFD 10GigFD 10GigFD MDIX MDI MDIX Auto Auto Auto Auto Auto off off off off off off off off 0 0 0 0 0 0 0 0 display interface brief down Field Mappings.
PAGE 108
display ip as-path Comware Related ProVision display ip as-path show ip aspath-list NOTE: This command is not supported on the HP 2920 Series switches. Displays BGP AS-Path list information HP Switch# display ip as-path ListID Mode Expression test1 permit $25 Field Descriptions ListID: AS path list ID. Mode: Match mode — permit or deny. Expression: Regular expression for matching.
PAGE 109
display ip check source Comware Related ProVision display ip check source show dhcp-snooping bindings Displays display dynamic IP source guard binding entries. HP Switch# display ip check source Total entries found: 3 MAC Address IP Address 005056-9f2c8b 192.168.1.1 005056-9f2c9b 192.167.1.1 005056-9f2c9b 192.167.0.
PAGE 110
display ip check source Field Mappings.
PAGE 111
display ip community-list Comware Related ProVision display ip community-list show ip community-list NOTE: This command is not supported on the HP 2920 Series switches. Displays BGP community list information HP Switch# display ip community-list Community List Number community-1 permit 10 deny 50 Field Descriptions Community List Number < community-name >: Specifies the community being reported. permit: Permitted routes that belong to the community . deny: Denied routes that belong to the community.
PAGE 112
display ip http Comware Related ProVision display ip http No equivalent ProVision software command Displays information about HTTP. HP Switch# display ip http HTTP port: 80 Basic ACL: n/a Current connection: 0 Operation status: enabled Minimum Software Version: 15.10.
PAGE 113
display ip https Comware Related ProVision display ip https No equivalent ProVision software command Displays information about HTTPs. HP Switch# display ip https HTTPS port: 443 SSL server policy: n/a Certificate access-control-policy: n/a Basic ACL: n/a Operation status: disabled Minimum Software Version: 15.10.
PAGE 114
display ip ip-prefix Comware Related ProVision display ip ip-prefix show ip prefix-list Displays all the prefix list information, including list name, address, length, rule type, ge and le [greater than or equal /less than or equal w.r.t mask range] for a specific network. This command is available only in manager mode. HP Switch# display ip ip-prefix abc Prefix-list abc Permitted n/a Denied n/a index: 5 permit 11.2.3.4/8 ge 8 le 8 Example of Related ProVision Software Command Output.
PAGE 115
display ipv6 dhcp duid Comware Related ProVision display ipv6 dhcp duid No equivalent ProVision software command Displays the DUID of the local switch. HP Switch# display ipv6 dhcp duid The DUID of this device: 0003-0001-00e0-fc00-5552. Field Descriptions The DUID of this device: The DHCP for IPv6 Unique Identifier (DUID). Operating Notes For more information about IPv6 DHCPv6, see the "DHCPv6-Relay" chapter in the latest IPv6 Configuration Guide for your switch.
PAGE 116
display ipv6 dhcp relay server-address all Comware Related ProVision display ipv6 dhcp relay server-address all show ipv6 helper-address Displays all DHCPv6 server address information. HP Switch# display ipv6 dhcp relay server-address all Interface: Vlan2 Server address(es) Output Interface 1::1 FF02::1:2 Vlan4 Interface: Vlan3 Server address(es) 1::1 FF02::1:2 Vlan4 Output Interface Field Descriptions Interface: Interface that serves as the DHCPv6 relay agent.
PAGE 117
display ipv6 dhcp relay server-address interface Comware Related ProVision display ipv6 dhcp relay server-address interface show ipv6 helper-address Displays DHCPv6 server address information of the specified interface. HP Switch# display ipv6 dhcp relay server-address interface vlan-interface 2 Interface: Vlan2 Server address(es) Output Interface 1::1 FF02::1:2 Vlan4 Field Descriptions Interface: Interface that serves as the DHCPv6 relay agent.
PAGE 118
display ipv6 dhcp relay statistics Comware Related ProVision display ipv6 dhcp relay statistics show dhcpv6-relay Displays packet statistics on the DHCPv6 relay agent.
PAGE 119
Operating Notes For more information about IPv6 DHCPv6, see the "DHCPv6-Relay" chapter in the latest IPv6 Configuration Guide for your switch. Example of Related ProVision Software Command Output. HP Switch(config)# show dhcpv6-relay DHCPV6 Relay Agent : Enabled Client Requests VLAN Name ---------DEFAULT...
PAGE 120
display ipv6 fib Comware Related ProVision display ipv6 fip show ipv6 route Displays IPv6 FIB entries. If no argument is specified, all IPv6 FIB entries will be displayed. The switch looks up a matching IPv6 FIB entry for forwarding an IPv6 packet.
PAGE 121
Dest : 2001:db8:a03:e102::/64 Gateway : VLAN10 Dist. : 0 Type : connected Metric : 1 Dest : fe80::%vlan10 Gateway : VLAN10 Dist. : 0 Type : connected Metric : 1 Dest : fe80::1%lo0 Gateway : lo0 Dist.
PAGE 122
display ipv6 fib Comware Related ProVision display ipv6 fib show ipv6 route Displays the IPv6 FIB entry of the specified destination IPv6 address. Note the following: • Without the prefix-length argument specified, this command displays the matching IPv6 FIB entry with the longest prefix. • With the prefix-length argument specified, this command displays the IPv6 FIB entry exactly matching the specified destination IPv6 address and prefix length.
PAGE 123
Dest : ::/0 Gateway : fe80::213:c4ff:fedd:14b0%vlan10 Dist. : 40 Type : static Metric : 0 Dest : ::1/128 Gateway : lo0 Dist. : 0 Dest : 2001:db8:a03:e102::/64 Gateway : VLAN10 Dist. : 0 Dest : fe80::%vlan10 Gateway : VLAN10 Dist. : 0 Dest : fe80::1%lo0 Gateway : lo0 Dist.
PAGE 124
display ipv6 neighbors all Comware Related ProVision display ipv6 ipv6 neighbors all show ipv6 neighbors Displays neighbor information. HP Switch(config)# display ipv6 neighbors all Type: S-Static IPv6 Address FE80::200:5EFF:FE32:B800 D-Dynamic Link-layer 0000-5e32-b800 VID N/A Interface State GE3/0/1 REACH T Age S - Field Descriptions IPv6 Address: IPv6 address of a neighbor. Link-layer: Link layer address (MAC address of a neighbor).
PAGE 125
fe80::10:27 fe80::213:c4ff:fedd:14b0 001560-7aadc0 REACH dynamic A3 0013c4-dd14b0 REACH dynamic A1 display ipv6 neighbors all 125
PAGE 126
display ipv6 routing-table Comware Related ProVision display ipv6 routing-table show ipv6 route Displays brief ipv6 routing information. The verbose option displays detailed information about the ipv6 routing table.
PAGE 127
Type : connected Sub-Type : NA Distance : 0 Metric : 1 Destination : 2001:db8:a::/64 Gateway : fe80::22:1%vlan22 Type : ospf3 Sub-Type : InterArea Distance : 110 Metric : 2 Destination : 2001:db8:b::/64 Gateway : VLAN22 Type : connected Sub-Type : NA Distance : 0 Metric : 1 Destination : 2001:db8:c::/64 Gateway : 2001:db8:e::55:2 Type : static Sub-Type : NA Distance : 120 Metric : 1 -- MORE --, next page: Space, next line: Enter, quit: Control-C Operating Notes For more information, refer to the latest IPv
PAGE 128
display ipv6 routing-table ipv6-address Comware Related ProVision display ipv6 routing-table ipv6-address show ipv6 route Displays routing information for a specified destination ipv6 address. The verbose option displays detailed information for the specified destination ipv6 address.
PAGE 129
Minimum Software Version: 15.10.
PAGE 130
display ipv6 routing-table protocol Comware Related ProVision display ipv6 routing-table protocol show ipv6 route {connected | static | ospf3} NOTE: This command is not supported for OSPFv3 on the HP 2920 Series switches. Displays routing information for a specified routing protocol. The routing protocol specified may be static, direct or ospfv3.
PAGE 131
display lacp system-id Comware Related ProVision display lacp system-id show lacp local Displays the system ID of the local system. The system LACP priority and the system MAC address comprise the system ID. HP Switch# display lacp system-id Actor System ID: 0x2f00, 001871-c42f00 Field Descriptions Actor System ID: The local system ID, including system LACP priority and system MAC address.
PAGE 132
Comware ProVision Software n/a Tx Timer n/a Rx Timer Expired Display Commands
PAGE 133
display link-aggregation Comware Related ProVision display link-aggregation load-sharing mode n/a Displays the load-sharing criteria for load-sharing link-aggregation (trunk) groups. NOTE: Link-aggregation in ProVision software is termed port trunking. Load-sharing is termed load-balancing. When load-balancing is configured as L4-based, the load-sharing mode includes source and destination MAC address, source and destination IP address, and source and destination TCP/UDP port number, as shown below.
PAGE 134
display link-aggregation member-port Comware Related ProVision display link-aggregation member-port display link-aggregation member-port GigabitEthernet No equivalent ProVision software command Displays the detailed link aggregation information of the specified member ports or all member ports if no port is specified.
PAGE 135
• G indicates whether the receive state machine of the sending system is using default operational partner information. 1 for true and 0 for false. • H indicates whether the receive state machine of the sending system is in the expired state. 1 for true and 0 for false. If a flag bit is set to 1, the corresponding English letter that otherwise is not output is displayed. Aggregation Interface: Aggregate interface to which the port belongs. Port Priority: Aggregation priority of the port.
PAGE 136
display link-aggregation summary Comware Related ProVision display link-aggregation summary No equivalent ProVision software command Displays the summary information of all aggregation groups. Information about the remote system for a static link aggregation group may be either shown as none or not displayed, because the aggregation group is unaware of information about the peer groups.
PAGE 137
display link-aggregation verbose Comware Related ProVision display link-aggregation verbose display link-aggregation No equivalent ProVision software command verbose Bridge-aggregation display link-aggregation verbose Bridge-aggregation Displays detailed information about the aggregation groups corresponding to the aggregate interfaces in the system.
PAGE 138
• E indicates whether the sending system considers that collection of incoming frames is enabled on the link. 1 for true and 0 for false. • F indicates whether the sending system considers that distribution of outgoing frames is enabled on the link. 1 for true and 0 for false. • G indicates whether the receive state machine of the sending system is using default operational partner information. 1 for true and 0 for false.
PAGE 139
display lldp local-information Comware Related ProVision display lldp local-information No equivalent ProVision software command Displays the LLDP information. This includes the global information and per interface information. HP Switch# display lldp local-information Global LLDP local-information Chassis ID : 0000-0000-1122 System name : HP-E3500yl-48G System description : HP J8693A Switch E3500yl-48G, revision K.15.09.0000x, ROM K.15.
PAGE 140
Unknown Policy VLAN tagged Media policy VlanID Media policy L2 priority Media policy Dscp : : : : : No No 1 6 46 LLDP local-information of port 2 : Port ID subtype : local Port ID : 2 Port description : 2 Management Management Management Management Management address address address address address type : : interface type : interface ID : OID : Port VLAN ID(PVID) : 1 ipv4 10.0.0.
PAGE 141
display lldp local-information global Comware Related ProVision display lldp local-information global No equivalent ProVision software command Displays LLDP system global information. HP Switch# display lldp local-information global Global LLDP local-information Chassis ID : 0000-0000-1122/00 System name : HP-E3500yl-48G System description : HP J8693A Switch E3500yl-48G, revision K.15.09.0000x, ROM K.15.28 HP-3500yl-48G Copyright (C) 1991-2012 Hewlett-Packard Development Company, L.P.
PAGE 142
display lldp local-information interface interface-type interface-number Comware Related ProVision display lldp local-information interface interface-type interface-number No equivalent ProVision software command Displays LLDP detailed information for a given interface.
PAGE 143
display lldp neighbor-information brief Comware Related ProVision display lldp neighbor-information brief show lldp info remote-device Displays brief information of all the ports connected to neighbors.
PAGE 144
display lldp neighbor-information list display lldp neighbor-information list system-name Comware Related ProVision display lldp neighbor-information list display lldp neighbor-information list system-name show lldp info remote-device HP Switch# display lldp neighbor_information list System Name Local Interface Chassis ID HP Switch 1 00 0f 90 dc 9f 80 Port ID 1 Example of Related ProVision Software Command Output.
PAGE 145
display lldp statistics Comware Related ProVision display lldp statistics show lldp stats Displays information about LLDP packets that are being advertised by the local system or by remote systems, and global LLDP information followed by each interface in the switch. The statistics refer to significant events that involve LLDP packet transmission and reception.
PAGE 146
display lldp statistics global Comware Related ProVision display lldp statistics global show lldp stats Displays global information about LLDP packets that are being advertised by the local system or by remote systems. The statistics refer to significant events that involve LLDP packet transmission and reception.
PAGE 147
display lldp statistics interface interface-type interface-number Comware Related ProVision display lldp statistics interface interface-type interface-number show lldp stats Displays information about LLDP packets on a particular interface that are being advertised by the local system or by remote systems. The statistics refer to significant events that involve LLDP packet transmission and reception.
PAGE 148
display lldp status Comware Related ProVision display lldp status No equivalent ProVision software command Displays information about Link Layer Discovery Protocol (LLDP) and Link Level Discovery Protocol-Media Endpoint Discovery (LLDP-MED) configuration and capabilities on the switch. LLDP and LLDP-MED are used to learn about and to distribute device information on network links. This command shows information on global level as well as the interface level.
PAGE 149
display lldp status interface interface-type interface number Comware Related ProVision display lldp status interface interface-type interface number No equivalent ProVision software command Displays information about Link Layer Discovery Protocol (LLDP) and Link Level Discovery Protocol-Media Endpoint Discovery (LLDP-MED) configuration and capabilities on the switch. LLDP and LLDP-MED are used to learn about and to distribute device information on network links.
PAGE 150
display lldp tlv-config interface interface-type interface-number Comware Related ProVision display lldp tlv-config interface interface-type interface-number No equivalent ProVision software command LLDP information is sent by devices from each of their interfaces at a fixed interval in the form of an Ethernet frame. Each frame contains one Link Layer Discovery Protocol Data Unit (LLDPDU). Each LLDPDU is a sequence of typelength- value (TLV) structures.
PAGE 151
display local-proxy-arp Comware Related ProVision display local-proxy-arp show ip Displays the status of the local proxy ARP. If an interface is specified, the local proxy ARP status of the specified interface is displayed. If no interface is specified, the local proxy ARP status of all interfaces is displayed.
PAGE 152
display logfile buffer Comware Related ProVision display logfile buffer show logging Displays system log information. HP Switch# display logfile buffer %@00061%Jan 01 00:00:47 2090 system: -------------------------%@00062%Jan 01 00:00:47 2090 system: Mgmt Module 1 went down without saving crash information %@03002%Jan 01 00:00:47 2090 system: System reboot due to Reset Switch %@02759%Jan 01 00:00:47 2090 chassis: Savepower LED timer is OFF.
PAGE 153
I 10/28/09 21:45:42 02751 chassis: AM1: LEDs for module in slot H configured ON. I 10/28/09 21:45:42 02751 chassis: AM1: LEDs for module in slot I configured ON. I 10/28/09 21:45:42 02751 chassis: AM1: LEDs for module in slot J configured ON. I 10/28/09 21:45:42 02751 chassis: AM1: LEDs for module in slot K configured ON. I 10/28/09 21:45:42 02751 chassis: AM1: LEDs for module in slot L configured ON.
PAGE 154
display loopback-detection Comware Related ProVision display loopback-detection No equivalent ProVision software command Displays the operating status of the loopback detection function. Field Descriptions HP Switch(config)# display loopback-detection Loopback-detection is running. Detection interval is 30 second(s).
PAGE 155
display mac-address Comware Related ProVision display mac-address show mac-address Displays information about the MAC address table. HP Switch# display mac-address MAC ADDR VLAN ID STATE PORT 001635-22ca40 1 Learned 001635-22ca7f 1 Learned 001122-334455 2 Config static INDEX A1 A1 A2 AGING TIME(s) AGING AGING NOAGED --- 3 mac address(es) found --- Example of Related ProVision Software Command Output.
PAGE 156
display mac-address aging-time Comware Related ProVision display mac-address aging-time show system information Displays the aging time of dynamic entries in the MAC address table. HP Switch# display mac-address aging-time Mac address aging time: 300s Field Descriptions Mac address aging time: Aging time of dynamic entries in the MAC address table. Operating Notes Comware displays mac-address as 1234-1234-1234 and ProVision displays it as 123456-123456.
PAGE 157
display mac-address multicast Comware Related ProVision display mac-address multicast No equivalent ProVision software command Displays static multicast MAC address entries. HP Switch# display mac-address multicast MAC ADDR VLAN ID STATE PORT INDEX 010122-334455 1 Multicast A1 012222-334455 1 Multicast F24 AGING TIME(s) NOAGED NOAGED --- 2 mac address(es) found --- Minimum Software Version: 15.10.
PAGE 158
display mac-authentication Comware Related ProVision display mac-authentication [interface] show port-access mac-based Displays MAC authentication settings and statistics, including the global settings, and port-specific settings and MAC authentication and online user statistics. If you specify a list of ports, the command displays port-specific settings and statistics only for the specified ports. If you do not specify any port, the command displays port-specific settings and statistics for all ports.
PAGE 159
The max allowed user number: Maximum number of users each slot supports. Current user number amounts to: Number of online users. Current domain: not configured, use default domain: Authentication domain that is currently used. Silent Mac User info: Information about silent MAC addresses. A MAC address is marked silent when it fails a MAC authentication, and at the same time, a quiet timer starts.
PAGE 160
Comware ProVision Software the max allowed user number n/a Current user number amounts to n/a Current domain: not configured, use default domain n/a Silent Mac User info n/a GigabitEthernet3/0/1 is link-up n/a MAC address authentication is enabled n/a Authenticate success: 0, failed: 0 n/a Current online user number n/a MAC Addr n/a Authenticate state n/a AuthIndex n/a 160 Display Commands
PAGE 161
display mac-authentication [interface …] Comware Related ProVision display mac-authentication [interface ...] show port-access mac-based Displays MAC authentication settings and statistics.
PAGE 162
Operating Notes For more information, refer to the latest Access Security Guide for your switch. Minimum Software Version: 15.10.
PAGE 163
display memory Comware Related ProVision display memory show system information Displays the current memory usage on the switch. HP Switch(config)# display memory System Total Memory(bytes): 128090112 Total Used Memory(bytes): 47385504 Used Rate: 36% Field Descriptions System Total Memory (bytes): Total system memory in the switch. Total Used Memory (bytes): Total system memory in use. Used Rate: Percentage of system memory in use.
PAGE 164
display mld group Comware Related ProVision display mld group show ipv6 mld Displays the number of active MLD (Multicast Listener Discovery) groups and the VLAN and IPv6 address on which each group is active. HP Switch# display mld group Total 4 MLD Group(s).
PAGE 165
For more on MLD, including additional MLD commands, see the “Multicast Listener Discovery (MLDv1 and MLDv2)” chapter in the latest IPv6 Configuration Guide for your switch. Minimum Software Version: 15.08. Example of Related ProVision Software Command Output.
PAGE 166
display mld group interface vlan-interface Comware Related ProVision display mld group interface vlan-interface show ipv6 mld vlan Displays information of all MLD groups. HP Switch# display mld group interface vlan-interface 30 Interface group report information Vlan-Interface30(2075:1:1:30::1): Total 5 MLD Groups reported Group : ff02::2 Last Reporter : fe80::3e4a:92ff:feab:9300 Uptime : 5 ... Expires : 00:02:18 Group : ff02::16 Last Reporter : fe80::3e4a:92ff:feab:9300 Uptime : 5 ...
PAGE 167
display mld group interface vlan-interface verbose Comware Related ProVision display mld group interface vlan-interface verbose show ipv6 mld vlan Displays information of all MLD groups. HP Switch# display mld group interface vlan-interface 30 verbose Interface group report information Vlan-Interface30(2075:1:1:30::1): Total 5 MLD Groups reported Group : ff02::2 Last Reporter : fe80::3e4a:92ff:feab:9300 Uptime : 5 ...
PAGE 168
Last reporter: IPv6 address of the host that last reported membership for this group Last-listener-query-counter: Number of MLD last listener queries sent Last-listener-query-timer-expiry: Remaining time of the MLD last listener query timer, where "off" means that the timer never times out Group mode: Multicast source filtering mode: • include • exclude This field is displayed only when the device is running MLDv2.
PAGE 169
display mld group port-info vlan display mld group port-info Comware Related ProVision display mld group port-info vlan No equivalent ProVision software command display mld group port-info Displays Layer 2 port information of MLD groups, including Layer 2 information of dynamic and static MLD group entries. HP Switch# display mld group port-info Total 1 IP Group(s). Total n/a IP Source(s). Total n/a MAC Group(s).
PAGE 170
display mld group verbose Comware Related ProVision display mld group verbose show ipv6 mld vlan Displays information about dynamically added MLD groups on all interfaces. HP Switch# display mld group verbose Total 5 MLD Group(s). Interface group report information Vlan-Interface30(2075:1:1:30::1): Total 5 MLD Groups reported Group : ff02::2 Last Reporter : fe80::3e4a:92ff:feab:9300 Uptime : 5 ...
PAGE 171
Expires: Remaining time of the IPv6 multicast group, where "off" means that the multicast group never times out Last reporter: IPv6 address of the host that last reported membership for this group Last-listener-query-counter: Number of MLD last listener queries sent Last-listener-query-timer-expiry: Remaining time of the MLD last listener query timer, where "off" means that the timer never times out Group mode: Multicast source filtering mode: • include • exclude This field is displayed only when the de
PAGE 172
display mld group x:x::x:x Comware Related ProVision display mld group x:x::x:x show ipv6 mld vlan Displays information of all MLD groups. HP Switch# display mld group ff02::2 Interface group report information Interface:Vlan30 Last Reporter : fe80::3e4a:92ff:feab:9300 Uptime : 5 ...
PAGE 173
display mld group x:x::x:x verbose Comware Related ProVision display mld group x:x::x:x verbose show ipv6 mld vlan Displays information of all MLD groups.
PAGE 174
display mld interface Comware Related ProVision display mld interface show ipv6 mld vlan Displays MLD configuration and operation information on the specified interface or all MLD-enabled interfaces.
PAGE 175
display mld interface verbose Comware Related ProVision display mld interface verbose show ipv6 mld vlan Displays MLD configuration and operation information on the specified interface or all MLD-enabled interfaces.
PAGE 176
Startup-query-timer-expiry: Remaining time of MLD startup query timer, where "off" means that the timer never times out Other-querier-present-timer-expiry: Remaining time of MLD other querier present timer, where "off" means that the timer never times out Proxying interface: The MLD proxy interface, where "none" means that no proxy interface exists MLD proxy is enabled: MLD proxying is enabled Version1-querier-present-timer-expiry: Remaining time of the MLDv1 querier present timer, where "off" means that th
PAGE 177
display mld interface vlan-interface Comware Related ProVision display mld interface vlan-interface show ipv6 mld vlan Displays MLD configuration and operation information on the specified interface or all MLD-enabled interfaces.
PAGE 178
display mld interface vlan-interface verbose Comware Related ProVision display mld interface vlan-interface verbose show ipv6 mld vlan Displays MLD configuration and operation information on the specified interface or all MLD-enabled interfaces.
PAGE 179
Startup-query-timer-expiry: Remaining time of MLD startup query timer, where "off" means that the timer never times out Other-querier-present-timer-expiry: Remaining time of MLD other querier present timer, where "off" means that the timer never times out Proxying interface: The MLD proxy interface, where "none" means that no proxy interface exists Total 1 MLD Group reported: Total number of MLD groups the interface has dynamically joined MLD proxy is enabled: MLD proxying is enabled Version1-querier-presen
PAGE 180
display mld routing-table Comware Related ProVision display mld routing-table No equivalent ProVision software command Displays information about the MLD routing table. HP Switch# display mld routing-table Routing table Total 2 entries 00001. (*, 2ffd::1) List of 2 downstream interfaces Vlan-interface100 (fe80::3ee5:a6ff:fe18:1142), Protocol: MLD Vlan-interface200 (fe80::3ee5:a6ff:fe18:1143), Protocol: MLD 00002.
PAGE 181
display monitor-link group [group-number | all], Comware Related ProVision display monitor-link group
PAGE 182
Comware ProVision Software Role n/a Status LtMState/LtD State Display Commands
PAGE 183
display multicast forwarding-table Comware Related ProVision display multicast forwarding-table No equivalent ProVision software command NOTE: This command is not supported on the HP 2920 Series switches. Displays multicast forwarding table information. If neither all-instance nor vpn-instance is specified, this command displays the information on the public network. Multicast forwarding tables guide multicast forwarding.
PAGE 184
display multicast routing-table Comware Related ProVision display multicast routing-table show ip mroute NOTE: This command is not supported on the HP 2920 Series switches. Displays multicast routing table information. Multicast routing tables are the basis of multicast forwarding. You can view the establishment state of an (S, G) entry by checking the multicast routing table. HP Switch# display multicast routing-table Multicast routing table of VPN-Instance: public net Total 1 entry,1 matched 00001.
PAGE 185
239.255.255.1 239.255.255.5 10.27.30.2 10.27.30.2 10.29.30.1 10.29.30.1 29 29 Operating Notes For more information, refer to the latest Multicast and Routing Guide for your switch. Minimum Software Version: 15.10.
PAGE 186
display multicast routing-table static Comware Related ProVision display multicast routing-table static show ip pim rpf-override NOTE: This command is not supported on the HP 2920 Series switches. Displays the information about multicast static routes. HP Switch# display multicast routing-table static Multicast Routing Table of VPN-Instance: n/a Routes : n/a Mroute 10.10.0.0/16 Interface = n/a RPF Neighbor = 2.2.2.
PAGE 187
Comware ProVision Software Interface n/a RPF Neighbor RPF IP Address Route-policy n/a Preference n/a Order n/a Running Configuration n/a display multicast routing-table static 187
PAGE 188
display multicast rpf-info Comware Related ProVision display multicast rpf-info No equivalent ProVision software command NOTE: This command is not supported on the HP 2920 Series switches. Displays rpf override information of a multicast source. HP Switch# display multicast rpf-info 10.10.10.10 RPF information about source 10.10.10.10: VPN instance: n/a RPF interface: Vlan-Interface 10 Referenced route/mask: 40.40.40.
PAGE 189
display ospf cumulative Comware Related ProVision display ospf cumulative show ip ospf statistics NOTE: This command is not supported on the HP 2920 Series switches. Displays OSPF statistics information. HP Switch# display ospf cumulative OSPF Process 1 with Router ID : 2.2.2.
PAGE 190
External: Number of Type-5 LSAs originated. NSSA: Number of Type-7 LSAs originated. Opq-Link: Number of Type-9 LSAs originated. Opq-Area: Number of Type104 LSAs originated. Opq-As: Number of Type-11 LSAs originated. LSA originated: Number of LSAs originated. LSA Received: Number of LSAs received. Routing Table: Routing table information. Intra Area: Intra-area route number. Inter Area: Inter-area route number. ASE: ASE route number.
PAGE 191
display ospf interface Comware Related ProVision display ospf interface show ip ospf interface NOTE: This command is not supported on the HP 2920 Series switches. Displays OSPF interface information for all OSPF processes. HP Switch(config)# display ospf interface OSPF Process 1 with Router ID : 192.168.1.1 Area : 0.0.0.0 IP Address Type State Cost Pri DR BDR --------------- --------- ------- ----- --- --------------- --------------192.168.1.1 PTP P-2-P 1562 1 0.0.0.0 0.0.0.0 Area : 0.0.0.
PAGE 192
HP Switch(config)# show ip ospf interface OSPF Interface Status IP Address Status --------------- -------172.16.0.1 enabled Area ID State Auth-type Cost Pri Passive --------------- ------- --------- ----- --- ------backbone DR none 1562 1 no OSPF Interface Field Mappings.
PAGE 193
display ospf lsdb Comware Related ProVision display ospf lsdb show ip ospf link-state show ip ospf external-link-state NOTE: This command is not supported on the HP 2920 Series switches. Displays OSPF link state database information. HP Switch# display ospf lsdb OSPF Process 1 with Router ID 7.7.7.7 Link State Database Type Router Router Network Sum-Net Type Router Router Network Sum-Net Area: 0.0.0.0 AdvRouter 11.0.9.2 11.0.9.1 11.0.9.2 11.0.9.1 Area: 0.0.0.1 LinkState ID AdvRouter 11.0.9.1 11.0.9.
PAGE 194
---------Router Router Network Summary Summary Summary Summary AsbSummary --------------10.0.8.32 10.0.8.33 10.3.2.37 10.3.16.0 10.3.16.0 10.3.17.0 10.3.17.0 10.0.8.36 --------------10.0.8.32 10.0.8.33 10.0.8.37 10.0.8.33 10.0.8.35 10.0.8.33 10.0.8.35 10.0.8.
PAGE 195
display ospf peer Comware Related ProVision display ospf peer show ip ospf neighbor NOTE: This command is not supported on the HP 2920 Series switches. Displays information about OSPF neighbors. HP Switch# display ospf peer OSPF Process 1 with Router ID 1.1.1.1 Neighbor Brief Information Area: 0.0.0.0 Router ID 1.1.1.2 Address 1.1.1.2 Pri Dead-Time 1 40 Interface Vlan11 State Full/DR Field Descriptions Area: Neighbor area. Router ID: Neighbor router ID Address: Neighbor interface address.
PAGE 196
Comware ProVision Software Dead-Time Dead Timer Expires Interface n/a State NbIfState/State Display Commands
PAGE 197
display ospf routing Comware Related ProVision display ospf routing show ip ospf NOTE: This command is not supported on the HP 2920 Series switches. Displays OSPF routing information for all OSPF processes. HP Switch(config)# display ospf routing OSPF Process 1 with Router ID 192.168.1.2 Routing Tables Routing for Network Destination Cost 192.168.1.0/24 1562 172.16.0.0/16 1563 Type Stub Inter NextHop 192.168.1.2 192.168.1.1 AdvRouter 192.168.1.2 192.168.1.1 Area 0.0.0.0 0.0.0.
PAGE 198
display ospf vlink Comware Related ProVision display ospf vlink show ip ospf virtual-link NOTE: This command is not supported on the HP 2920 Series switches. Displays OSPF virtual link information. HP Switch# display ospf vlink OSPF Process 1 with Router ID 3.3.3.3 Virtual Links Virtual-link Neighbor-ID -> 2.2.2.2, Neighbor-State: Full Interface: 10.1.2.1 (Vlan-interface11) Cost: 1562 State: P-2-P Type: Virtual Transit Area: 0.0.0.
PAGE 199
ospf vlink Field Mappings.
PAGE 200
display ospfv3 Comware Related ProVision display ospfv3 show ipv6 ospf3 NOTE: This command is not supported on the HP 2920 Series switches. Displays brief information about OSPFv3. HP Switch# display ospfv3 Routing Process "OSPFv3 (1)" with ID 3.3.3.
PAGE 201
display ospfv3 area area-id peer interface interface-type interface number Comware Related ProVision display ospfv3 area area-id peer interface interface-type No equivalent ProVision software command interface number NOTE: This command is not supported on the HP 2920 Series switches. Displays OSPFv3 neighbor information. HP Switch# display ospfv3 area 0 peer Vlan-interface 1 OSPFv3 (Process 1) OSPFv3 Area (0.0.0.0) Neighbor ID 1.1.1.
PAGE 202
display ospfv3 area area-id peer peer-router-id Comware Related ProVision display ospfv3 area area-id peer peer-router-id show ipv6 ospf3 neighbor detail NOTE: This command is not supported on the HP 2920 Series switches. Displays OSPFv3 neighbor information for the specified area. HP Switch(config)# display ospfv3 area 0 peer 1.1.1.1 OSPFv3 Process (1) Neighbor 1.1.1.1 is Full, interface address FE80::21B:3FFF:FEF7:DEC0 In the area 0.0.0.0 via interface Vlan-interface1 DR is 2.2.2.
PAGE 203
Priority Options Events : 1 : 19 : 0 Retransmit Queue Length Neighbor Uptime Dead Timer Expires : 0 : 1days : 33 sec display ospfv3 area area-id peer peer-id Field Mappings.
PAGE 204
display ospfv3 area area-id peer verbose Comware Related ProVision display ospfv3 area area-id peer verbose No equivalent ProVision software command NOTE: This command is not supported on the HP 2920 Series switches. Displays detailed information about OSPFv3 neighbors for a specified area. HP Switch(config)# display ospfv3 area 1 peer verbose Neighbor 3.3.3.3 is Full, interface address FE80::221:F7FF:FE1B:EC80 In the area 0.0.0.1 via interface Vlan-interface2 DR is 3.3.3.3 BDR is 2.2.2.
PAGE 205
display ospfv3 interface Comware Related ProVision display ospfv3 interface show ipv6 ospf3 interface NOTE: This command is not supported on the HP 2920 Series switches. Displays OSPF interface information for all OSPF processes. NOTE: Only one process is supported, so the process number is always 1. HP Switch(config)# display ospf3 interface Vlan-interface4 is down, line protocol is up Interface ID vlan-4 IPv6 Prefixes 1234::2/96 (Link-Local Address): OSPFv3 Process (1), Area 0.0.0.
PAGE 206
Time Interval Configured: Time interval in seconds configured on the interface: • Hello—Hello interval. • Dead—Dead interval. • Wait—After this timer expires, the interface quits from the waiting state. • Retransmit—LSA retransmission interval. Hello due in: Hello packet will be sent in the indicated number of seconds. Neighbor Count: Number of neighbors on the interface. Adjacent Neighbor Count: Number of adjacencies on the interface.
PAGE 207
Comware ProVision Software Backup Designated Router Backup Desig.
PAGE 208
display ospfv3 lsdb Comware Related ProVision display ospfv3 lsdb show ipv6 ospf3 link-state NOTE: This command is not supported on the HP 2920 Series switches. Displays OSPFv3 LSDB information. This command is available only in manager mode. HP Switch# display ospfv3 lsdb OSPFv3 Router with ID (2.2.2.2) (Process 1) Link-LSA (Interface Vlan-interface1) --------------------------------------------------------------------Link State ID Origin Router Age SeqNum CkSum Prefix 5.178.0.0 1.1.1.
PAGE 209
--------------------------------------------------------------------Link State ID Origin Router Age SeqNum CkSum Prefix Reference 0.0.0.2 2.2.2.2 0651 0x8000000b 0x37b2 1 Network-LSA AS-external-LSA --------------------------------------------------------------------Link State ID Origin Router Age SeqNum CkSum 0.0.0.1 2.2.2.2 0375 0x8000000b 0x999a 0.0.0.2 2.2.2.2 0570 0x80000002 0x6ebc Minimum Software Version: 15.10.
PAGE 210
display ospfv3 lsdb statistics Comware Related ProVision display ospfv3 lsdb statistics No equivalent ProVision software command NOTE: This command is not supported on the HP 2920 Series switches. Displays LSA statistics in the OSPFv3 LSDB. This command is available only in manager mode. HP Switch# display ospfv3 lsdb statistics OSPFv3 Router with ID (2.2.2.
PAGE 211
display ospfv3 peer Comware Related ProVision display ospfv3 peer show ipv6 ospf3 neighbor NOTE: This command is not supported on the HP 2920 Series switches. Displays OSPFv3 neighbor information. HP Switch(vlan-2)# display ospfv3 peer OSPFv3 Area ID 0.0.0.1 (Process 1) Neighbor ID Pri State Dead Time Interface Instance ID -------------------------------------------------------------------------120.85.228.88 1 FULL 00:00:33 Vlan2 0 Field Descriptions Neighbor ID: Router ID of a neighbor.
PAGE 212
Comware ProVision Software n/a Rxmt QLen n/a Events Display Commands
PAGE 213
display ospfv3 peer peer-router-id Comware Related ProVision display ospfv3 peer peer-router-id show ipv6 ospf3 neighbor detail NOTE: This command is not supported on the HP 2920 Series switches. Displays the router ID of the specified neighbor. HP Switch# display ospfv3 peer 2.2.2.2 Neighbor 2.2.2.2 is Full, interface address FE80::223:89FF:FECB:6FDC In the area 0.0.0.0 via interface Vlan-interface1 DR is 2.2.2.2 BDR is 1.1.1.
PAGE 214
Options Events : 19 : 0 Neighbor Uptime Dead Timer Expires : 1days : 33 sec display ospfv3 peer verbose Field Mappings.
PAGE 215
display ospfv3 peer statistics Comware Related ProVision display ospfv3 peer statistics No equivalent ProVision software command NOTE: This command is not supported on the HP 2920 Series switches. Displays information about all OSPFv3 neighbors on the router, that is, number of neighbors in different states. HP Switch# display ospfv3 peer statistics OSPFv3 Router with ID (2.2.2.
PAGE 216
display ospfv3 peer verbose Comware Related ProVision display ospfv3 peer verbose show ipv6 ospf3 neighbor detail NOTE: This command is not supported on the HP 2920 Series switches. Displays detailed information about OSPFv3 neighbors. HP Switch# display ospfv3 peer verbose Neighbor 2.2.2.2 is Full, interface address FE80::223:89FF:FECB:6FDC In the area 0.0.0.0 via interface Vlan-interface1 DR is 2.2.2.2 BDR is 1.1.1.
PAGE 217
Options Events : 19 : 0 Neighbor Uptime Dead Timer Expires : 1days : 33 sec display ospfv3 peer verbose Field Mappings.
PAGE 218
display ospfv3 statistic Comware Related ProVision display ospfv3 statistic show ipv6 ospf3 statistics NOTE: This command is not supported on the HP 2920 Series switches. Displays outbound/inbound OSPFv3 packet statistics on associated interface( s). HP Switch(vlan-2)# display ospfv3 statistics OSPFv3 Statistics Interface 2 Instance 0 Type Input Output Hello 6 10 DB Description 2 5 Ls Req 1 1 Ls Upd 2 3 Ls Ack 2 2 Discarded 32 1 Field Descriptions Interface: Interface name. Instance: Instance number.
PAGE 219
Per-VLAN OSPF Statistics Field Content Tx/Rx LSR Packet Count Number of link-state request packets sent/received on each subnet interface Tx/Rx LSU Packet Count Number of link-state update packets sent/received on each subnet interface Tx/Rx LSA Packet Count Number of link-state acknowledgement packets sent/ received on each subnet interface OSPF errors Number of errors detected on the VLAN subnet during OSPF packet exchange HP Switch# show ipv6 ospf3 statistics vlan 55 OSPFv3 statistics for VLAN
PAGE 220
display ospfv3 vlink Comware Related ProVision display ospfv3 vlink show ipv6 ospf3 virtual-link ? NOTE: This command is not supported on the HP 2920 Series switches. Displays OSPFv3 virtual link information. HP Switch# display ospfv3 vlink Virtual Link VLINK1 to router 1.1.1.1 is up Transit area :0.0.0.
PAGE 221
ospfv3 vlink Field Mappings.
PAGE 222
display pim bsr-info Comware Related ProVision display pim bsr-info show ip pim bsr NOTE: This command is not supported on the HP 2920 Series switches. Displays the BSR information in the PIM domain and the locally configured C-RP information in effect. HP Switch# display pim bsr-info Elected BSR Address : 10.10.10.11 Priority : 0 Hash mask length : 30 State: n/a Scope: n/a Uptime : 00:08:00 Next BSR message scheduled at : 01:20:00 Candidate BSR Address : 10.10.10.
PAGE 223
Next advertisement scheduled at: Length of time in which the C-RP will send the next advertisement message, in hh:mm:ss. Operating Notes For more information on PIM, see the "PIM-SM (Sparse Mode)" or the "PIMDM (Dense Mode) chapters in the latest Multicast and Routing Guide for your switch. Example of Related ProVision Software Command Output. display pim bsr-info Field Mappings.
PAGE 224
display pim control-message counters Comware Related ProVision display pim control-message counters No equivalent ProVision software command NOTE: This command is not supported on the HP 2920 Series switches. Displays statistics information of PIM control messages.
PAGE 225
display pim grafts Comware Related ProVision display pim grafts No equivalent ProVision software command NOTE: This command is not supported on the HP 2920 Series switches. Displays information about unacknowledged PIM-DM graft messages. HP Switch# display pim grafts vlan 1 name "DEFAULT_VLAN" no untagged 1-2,48 untagged 3-47 ip address dhcp-bootp exit vlan 10 name "VLAN10" untagged 1,48 ip address 10.10.10.3 255.255.255.0 ip igmp exit vlan 30 name "VLAN30" untagged 2 ip address 30.30.30.2 255.255.
PAGE 226
display pim interface Comware Related ProVision display pim interface show ip pim interface NOTE: This command is not supported on the HP 2920 Series switches. Displays the PIM information on the specified interface or all interfaces. HP Switch# display pim interface VPN-Instance: n/a Interface NbrCnt HelloInt Vlan10 n/a 30 Vlan20 n/a 30 Vlan30 n/a 30 DR-Pri 1 1 1 DR-Address 10.10.10.11 20.20.20.20 30.30.30.30 Field Descriptions VPN-Instance: public net: Public network.
PAGE 227
display pim interface verbose Comware Related ProVision display pim interface verbose show ip pim interface NOTE: This command is not supported on the HP 2920 Series switches. Displays detailed PIM information. HP Switch# display pim interface verbose Interface : Vlan-interface10, 10.10.10.10 PIM version : n/a PIM mode : 2 PIM DR : 10.10.10.
PAGE 228
PIM neighbor tracking (configured): Configured neighbor tracking status (enabled/disabled). PIM generation ID: Generation_ID value. PIM require generation ID: Rejection of Hello messages without Generation_ID (enabled/disabled). PIM hello hold interval: PIM neighbor timeout time. PIM assert hold interval: Assert timeout time. PIM triggered hello delay: Maximum delay of sending hello messages. PIM J/P interval: Join/prune interval. PIM J/P hold interval: Join/prune timeout time.
PAGE 229
Comware ProVision Software PIM override interval (negotiated) n/a PIM override interval (configured) Override Interval (msec0 PIM neighbor tracking (negotiated) n/a PIM neighbor tracking (configured) n/a PIM generation ID n/a PIM require generation ID n/a PIM hello hold interval Hello Delay (sec) PIM assert hold interval n/a PIM triggered hello delay n/a PIM J/P interval n/a PIM J/P hold interval n/a PIM state-refresh processing n/a PIM state-refresh interval n/a PIM state-refres
PAGE 230
display pim join-prune Comware Related ProVision display pim join-prune No equivalent ProVision software command NOTE: This command is not supported on the HP 2920 Series switches. HP Switch# display pim join-prune mode sm VPN-Instance: public net Expiry Time: 51 sec Upstream nbr: 10.10.10.1 (Vlan-Interface10) 1 (*, G) join(s), 1 (S, G) join(s), 0 (S, G, rpt) prune(s) ------------------------------------------------------------Total (*, G) join(s): 1, (S, G) join(s): 1, (S, G, rpt) prune(s): 0 |...+..
PAGE 231
display pim neighbor Comware Related ProVision display pim neighbor show ip pim neighbor NOTE: This command is not supported on the HP 2920 Series switches. Displays information about PIM neighbors. HP Switch# display pim neighbor VPN-Instance: n/a Total Number of Neighbors = n/a Neighbor Interface Uptime Expires Dr-Priority Mode 10.1.1.2 Vlan100 02:50:49 00:01:31 n/a n/a 20.1.1.
PAGE 232
Comware ProVision Software Expires/Expiry time Expire Time (sec) Dr-Priority/DR Priority DR Priority Mode n/a 232 Display Commands
PAGE 233
display pim neighbor verbose Comware Related ProVision display pim neighbor verbose show ip pim neighbor NOTE: This command is not supported on the HP 2920 Series switches. Displays information about PIM neighbors. HP Switch# display pim neighbor 11.110.0.20 verbose VPN-Instance: n/a Neighbor: 11.110.0.
PAGE 234
HP Switch(config)# show ip pim neighbor PIM Neighbors IP Address --------------10.10.10.2 10.20.10.1 VLAN ---100 200 Up Time (sec) Expire Time (sec) DR Priority ---------------- ---------------- ---------348 90 1 410 97 1 display pim neighbor Field Mappings.
PAGE 235
display pim routing-table Comware Related ProVision display pim routing-table No equivalent ProVision software command NOTE: This command is not supported on the HP 2920 Series switches. Displays the contents of the PIM multicast routing table, which includes SPT and RPF information. HP Switch# display pim routing-table VPN-Instance: public net Total 0 (*, G) entry; 1 (S, G) entry (172.168.0.12, 227.0.0.
PAGE 236
display pim rp-info Comware Related ProVision display pim rp-info No equivalent ProVision software command NOTE: This command is not supported on the HP 2920 Series switches. Displays information about pim RP. HP Switch# display pim rp-info VPN-Instance: public net PIM-SM BSR RP information: Group/MaskLen: 224.0.0.0/4 RP: 10.10.10.11 Priority: n/a HoldTime: 150 Uptime: n/a Expires: 00:01:00 Minimum Software Version: 15.10.
PAGE 237
display poe device Comware Related ProVision display poe device show power-over-ethernet brief NOTE: This command is not supported on the HP 2920 Series switches. Displays the mapping between ID, module, and slot of the power sourcing equipment (PSE). HP Switch# display poe device PSE ID SlotNo SubSNo PortNum MaxPower(W) A 1 n/a 24 370 State off Model J9310A Example of Related ProVision Software Command Output.
PAGE 238
display poe interface Comware Related ProVision display poe interface show power-over-ethernet brief NOTE: This command is not supported on the HP 2920 Series switches. Displays the PoE status of a specific port on the switch.
PAGE 239
Operating Notes For more information, refer to the latest Management and Configuration Guide for your switch. Minimum Software Version: 15.10.
PAGE 240
display poe interface power Comware Related ProVision display poe interface power show power-over-ethernet brief NOTE: This command is not supported on the HP 2920 Series switches. Displays the PoE power information of the specified port on the switch. If you enter the command without an argument, the PoE power information about all PoE-capable ports on the switch is displayed. HP Switch# display poe interface power Interface CurPower PeakPower MaxPower (W) (W) (W) 1 0.0 0.0 15.4 2 0.0 0.0 15.4 3 0.
PAGE 241
Operating Notes For more information, refer to the latest Management and Configuration Guide for your switch. Minimum Software Version: 15.10.
PAGE 242
display poe power-usage Comware Related ProVision display poe power-usage show power-over-ethernet brief NOTE: This command is not supported on the HP 2920 Series switches. Displays the power information of the PoE power and all PSEs.
PAGE 243
display poe-power alarm Comware Related ProVision display poe-power alarm show system power-supply NOTE: This command is not supported on the HP 2920 Series switches. Displays detailed alarm information about the PoE PSUs. HP Switch# display poe-power alarm PSU alarm detail, PSU number : 2 PSU 1 alarm : POWERED PSU 2 alarm : POWERED Example of Related ProVision Software Command Output.
PAGE 244
display poe-power switch state Comware Related ProVision display poe-power switch state No equivalent ProVision software command NOTE: This command is not supported on the HP 2920 Series switches. Displays the number and current state of the AC power distribution switches of the PSUs. HP Switch# display poe-power switch state Switch Number : 3 Switch 1 State : AC Switch Off Switch 2 State : AC Switch High Voltage Switch 3 State : AC Switch Off Minimum Software Version: 15.10.
PAGE 245
display port trunk Comware Related ProVision display port trunk No equivalent ProVision software command Displays information about the hybrid or trunk ports on the switch, including port names, default VLAN IDs (untagged vlan), and allowed VLAN IDs (tagged vlan). HP Switch# display port trunk Interface PVID VLAN passing A1 1 1-2, 5-10 A2 10 1, 5 Minimum Software Version: 15.10.
PAGE 246
display power Comware Related ProVision display power show system power-supply Displays information about the power supply of a device. HP Switch# display power Power 1 State: Powered Power 2 State: Powered Power 3 State: Not Present Power 4 State: Not Present Field Descriptions Power: Number of power supply bay. State: State of power supply. Example of Related ProVision Software Command Output.
PAGE 247
display protocol-vlan Comware Related ProVision display protocol-vlan No equivalent ProVision software command Displays the protocols and protocol indexes configured on the specified VLANs. HP Switch# display protocol-vlan VLAN ID:10 Protocol Index Protocol Type ============================================= 1 IPv4 2 IPX 3 ARP Minimum Software Version: 15.10.
PAGE 248
display protocol-vlan interface Comware Related ProVision display protocol-vlan interface No equivalent ProVision software command Displays information about protocol-based VLANs on all ports.
PAGE 249
display proxy-arp Comware Related ProVision display proxy-arp show ip Displays the proxy ARP status. If an interface is specified, proxy ARP status of the specified interface is displayed; if no interface is specified, proxy ARP status of all interfaces is displayed. HP Switch# display proxy-arp VLAN30 Proxy ARP status: disabled VLAN33 Proxy ARP status: disabled Operating Notes For more information, see the “IP Routing Features” chapter in the latest Multicast and Routing Guide for your switch.
PAGE 250
display public-key local rsa public Comware Related ProVision display public-key local rsa public show crypto host-public-key show ip host-public-key Displays public key information of the local key pairs. This command is available only in manager mode.
PAGE 251
display public-key peer Comware Related ProVision display public-key peer show ip client-public-key Displays brief information about all the public keys of remote hosts.
PAGE 252
display radius scheme Comware Related ProVision display radius scheme show radius show radius host show accounting Displays the configuration information of RADIUS schemes. HP Switch# display radius scheme -----------------------------------------------------------------SchemeName : n/a Index : n/a Type : n/a Primary Auth Server : IP : 1.2.3.4 Port : 1812 State : n/a Encryption Key : samplee123 VPN instance : n/a Primary Acct Server : IP : 1.2.3.
PAGE 253
Field Descriptions SchemeName: Name of the RADIUS scheme. Index: Index number of the RADIUS scheme. Type: Type of the RADIUS server, extended or standard. Primary Auth Server: Information about the primary authentication server. Primary Acct Server: Information about the primary accounting server. Second Auth Server: Information about the secondary authentication server. Second Acct Server: Information about the secondary accounting server. IP: Ip address of the server. Port: Service port of the server.
PAGE 254
Deadtime(min) : 5 Timeout(secs) : 10 Retransmit Attempts : Global Encryption Key Dynamic Authorization Source IP Selection : 2 : myg10balkey UDP Port : 3799 Outgoing Interface Auth Acct DM/ Server IP Addr Port Port CoA --------------- ---- ---- --192.33.12.65 1812 1813 No Time Window Encryption Key OOBM ------ -------------------------------- ----300 my65key No HP Switch(config)# show radius host 192.33.12.65 Status and Counters - RADIUS Server Information Server IP Addr : 192.33.12.
PAGE 255
Comware ProVision Software Encryption Key Encryption Key VPN instance n/a Auth Server Encryption Key n/a Acct Server Encryption Key n/a Accounting-On packet disable, send times n/a Interval for timeout (sec) Timeout (secs) Retransmission times for timeout n/a Interval for realtime accounting (minute) Interval(min) Retransmission times of realtime-accounting packet n/a Retransmission times of stop-accounting packet n/a Quiet-interval(min) Deadtime (min) Username format n/a Data flow
PAGE 256
display rip Comware Related ProVision display rip No equivalent ProVision software command Displays RIP configuration information. The command provides information regarding the version, preference, cost, summary, maximum number of balanced paths, configured peers, number of route changes and number of replies to queries in a RIP route.
PAGE 257
display rip interface Comware Related ProVision display rip interface No equivalent ProVision software command Displays RIP interface information of the RIP process. If no interface is specified, information about all RIP interfaces of the RIP process is displayed. HP Switch# display rip 1 interface Interface-name: Vlan-interface2 Address/Mask:2.2.2.
PAGE 258
display rip process-id ip-address mask/mask-length Comware Related ProVision display rip process-id ip-address mask/mask-length No equivalent ProVision software command Displays routes learnt by RIP. The command provides information regarding the peer address, vlan-interface (to which the peer is connected), route destination, route destination mask, route NextHop, route cost, route flags, route secs for all the routes that RIP has learnt. HP Switch # display rip 1 route 20.0.0.
PAGE 259
display rip process-id route Comware Related ProVision display rip process-id route No equivalent ProVision software command HP Switch# display rip 1 route Route Flags: R - RIP, T - TRIP P - Permanent, A - Aging, S - Suppressed, G - Garbage-collect ----------------------------------------------------------------Peer 10.1.1.1 on Vlan-interface10 Destination/Mask Nexthop Cost Tag Flags Sec 5.0.0.0/8 10.1.1.1 2 0 RA 5 6.0.0.0/8 10.1.1.1 1 0 RA 5 20.0.0.0/8 10.1.1.
PAGE 260
display rip process-id route peer ip-address Comware Related ProVision display rip process-id route peer ip-address No equivalent ProVision software command HP Switch# display rip 1 route peer 10.1.1.1 Route Flags: R - RIP, T - TRIP P - Permanent, A - Aging, S - Suppressed, G - Garbage-collect ----------------------------------------------------------------Peer 10.1.1.1 on Vlan-interface10 Destination/Mask 5.0.0.0/8 6.0.0.0/8 20.0.0.0/8 260 Display Commands Nexthop 10.1.1.1 10.1.1.1 10.1.1.
PAGE 261
display rmon statistics Comware Related ProVision display rmon statistics show rmon statistics Displays rmon statistics for the remote monitoring statistics information.
PAGE 262
display route-policy Comware Related ProVision display route-policy show route-map Displays FIPS state. By default, the FIPS mode is disabled.
PAGE 263
display saved-configuration Comware Related ProVision display saved-configuration show config Displays contents of the configuration file saved for the next startup of the switch. HP Switch# display saved-configuration ; J8697A Configuration Editor; Created on release #K.15.09.0000x ; Ver #03:01.1f.
PAGE 264
display saved-configuration by-linenum Comware Related ProVision display saved-configuration by-linenum show config Displays the saved configuration of the switch with the line number. This command adds the line number to the output of display saved-configuration. This command is available only in manager mode. HP Switch# display saved-configuration by-linenum ; J8692A Configuration Editor; Created on release #K.15.09.0000x ; Ver #03:01.1f.
PAGE 265
display schedule reboot Comware Related ProVision display schedule reboot show reload < after | at > Displays the user-configured switch reboot (reload) time. For example, if the current date and time is March 21, 2012 at 1:05 PM (13:05), and the switch is configured to reboot (reload) at 5:00 PM (17:00) on the same date, then you would see the following output when executing this command: HP Switch(config)# display schedule reboot System will reboot at 17:00 03/21/2012 (in 3 hours and 55 minutes).
PAGE 266
display sflow display sflow slot Comware Related ProVision display sflow sh sflow agent display sflow slot sh sflow sampling-polling Displays the sflowglobal, collector and port information. HP Switch# display sflow sFlow Version: 1.3;HP;K.15.10.0000x sFlow Global Information: Agent IP:120.93.219.32(Auto) Collector Information: ID IP Port Aging Size Description 1 1.2.3.4 1 2147483512 1400 n/a 2 1.2.3.5 2 2147483525 1400 n/a 3 1.2.3.
PAGE 267
display snmp-agent community Comware Related ProVision display snmp-agent community show snmpv3 community Displays community information for SNMPv1 or SNMPv2. This command is available only in manager mode. HP Switch# display snmp-agent community Community name: public Group name: n/a Storage-type: volatile Example of Related ProVision Software Command Output.
PAGE 268
display snmp-agent group Comware Related ProVision display snmp-agent group show snmpv3 group Displays information for the SNMPv3 agent group, including group name, security model, MIB view, and storage type. Absence of the group-name parameter indicates that information for all groups is displayed.
PAGE 269
Notifyview: OperatorReadView Storage-type: ReadOnly Group name: ComOperatorRW Security model: v1 noAuthnoPriv Readview: OperatorReadView Writeview: OperatorReadView Notifyview: OperatorReadView Storage-type: ReadOnly Group name: ComOperatorRW Security model: v2 noAuthnoPriv Readview: OperatorReadView Writeview: OperatorReadView Notifyview: OperatorReadView Storage-type: ReadOnly Group name: OperatorNoAuth Security model: v3 noAuthnoPriv Readview: OperatorReadView Writeview: DiscoverView Notifyview: Operator
PAGE 270
display snmp-agent local-engineid Comware Related ProVision display snmp-agent local-engineid show snmpv3 engineid Displays the SNMP agent local engine ID. HP Switch# display snmp-agent local-engineid SNMP local EngineID: 0000000b0000001871c42f00 Field Descriptions SNMP local EngineID: Identifies an SNMP entity uniquely within an SNMP domain. Operating Notes There is no specific user configuration command for SNMP agent local engine ID.
PAGE 271
display snmp-agent mib-view Comware Related ProVision display snmp-agent mib-view show snmpv3 group Displays the View name, MIB Subtree, Subtree mask, Storage-type, View Type, and View status. This command is available only in manager mode. HP Switch# display snmp-agent mib-view View name: DiscoverView MIB Subtree: 1.3.6.1.6.3.15.1.2.2.1.7 Subtree mask: Storage-type: readOnly View Type: included View status: notInService Storage-type: readOnly View name: DiscoverView MIB Subtree: 1.3.6.1.6.3.15.1.2.2.1.
PAGE 272
display snmp-agent statistics Comware Related ProVision display snmp-agent statistics No equivalent ProVision software command Displays SNMP statistics, identifies SNMP PDUs, and provides information regarding the number of PDUs in request, reply, get, set, errors and MIB retrieval and altered state.
PAGE 273
display snmp-agent sys-info Comware Related ProVision display snmp-agent sys-info show system information Displays current SNMP system information. HP Switch# display snmp-agent sys-info The contact person for this managed node: admin The physical location of this node: HP SNMP version running in the system: SNMPv1 SNMPv2c SNMPv3 Example of Related ProVision Software Command Output.
PAGE 274
display snmp-agent trap-list Comware Related ProVision display snmp-agent trap-list show snmp-server traps Displays modules that can generate traps and whether or not their trap function is enabled. This command is available only in manager mode.
PAGE 275
display snmp-agent usm-user Comware Related ProVision display snmp-agent usm-user show snmpv3 user Displays the snmp users configured in the system. This command is available only in manager mode.
PAGE 276
display ssh client source Comware Related ProVision display ssh client source No equivalent ProVision software command Displays the source IP address or source interface currently set for the SSH client. If neither source IP address nor source interface is specified for the SSH client, the system will prompt you to specify the source information. HP Switch# display ssh client source Neither source IP address nor source interface was specified for the STelnet client.
PAGE 277
display ssh server session Comware Related ProVision display ssh server session show ip ssh Displays SSH server session information. This command is available only in manager mode. HP Switch# display ssh server session Conn A1 Ver 2.0 Encry AES State Established Retry n/a SerType Stelnet Username manager Example of Related ProVision Software Command Output.
PAGE 278
display ssh server status Comware Related ProVision display ssh server status show ip ssh Displays the SSH server status information or session information.
PAGE 279
display ssh server-info Comware Related ProVision display ssh server-info No equivalent ProVision software command Displays mappings between SSH servers and their host public keys saved on the client. HP Switch# display ssh server-info Server Name(IP) Server public key name -------------------------------------120.85.212.127 n/a Minimum Software Version: 15.10.
PAGE 280
display ssl client-policy Comware Related ProVision display ssl client-policy show ip ssh Displays information about all SSL client policies. This command is available only in manager mode. HP Switch# display ssl client-policy SSL Client Policy: n/a SSL Version: TLS 1.0 PKI Domain: n/a Prefer Ciphersuite: aes256-ctr aes256-cbc rijndael-cbc@lysator.liu.
PAGE 281
display ssl server-policy Comware Related ProVision display ssl server-policy show ip ssh Displays information about all SSL client policies. This command is available only in manager mode. HP Switch# display ssl server-policy SSL Server Policy: n/a PKI Domain: n/a Ciphersuite: aes256-ctr aes256-cbc rijndael-cbc@lysator.liu.
PAGE 282
Minimum Software Version: 15.10.
PAGE 283
display startup Comware Related ProVision display startup No equivalent ProVision software command Displays the configuration file used at the current system startup and the configuration file(s) to be used at the next system startup. HP Switch# display startup Current startup saved-configuration file: flash:/svt-1.cfg Next startup saved-configuration file for primary image: flash:/ svt-1.cfg Next startup saved-configuration file for secondary image: flash:/svt-2.cfg Minimum Software Version: 15.10.
PAGE 284
display stp Comware Related ProVision display stp show spanning-tree Displays the MSTP status and statistics. Based on the MSTP status and statistics, you can analyze and maintain the network topology or check whether MSTP is working normally. Spanning-tree protocol is enabled HP Switch# display stp -------[CIST Global Info][Mode STP]------CIST Bridge :32768.3ce5-a674-b433 Bridge Times :Hello 2s MaxAge 20s FwDly 15s MaxHop 20 CIST Root/ERPC :32768.3ce5-a674-b433 / 0 CIST RegRoot/IRPC :32768.
PAGE 285
Switch Priority : 32768 Max Age : 20 Max Hops : 20 Forward Delay : 15 Topology Change Count : 1 Time Since Last Change : 20 mins CST Root MAC Address : 001083-847000 CST Root Priority : 0 CST Root Path Cost : 60000 CST Root Port : 1 IST Regional Root MAC Address : 0024a8-d13a40 IST Regional Root Priority : 32768 IST Regional Root Path Cost : 0 IST Remaining Hops : 20 Root Guard Ports : Loop Guard Ports : 2 TCN Guard Ports : BPDU Protected Ports : BPDU Filtered Ports : PVST Protected Ports : PVST Filtered Po
PAGE 286
display stp abnormal-port Comware Related ProVision display stp abnormal-port show spanning-tree detail show spanning-tree detail NOTE: This command is not supported on the HP 2920 Series switches. Displays information about ports blocked by spanning tree protection functions. HP Switch# display stp abnormal-port MSTID Blocked Port Reason 1 A1 ROOT-Protected 2 A2 LOOP-Protected Example of Related ProVision Software Command Output.
PAGE 287
display stp bpdu-statisticsdisplay stp bpdu-statistics interface GigabitEthernet display stp bpdu-statistics interface GigabitEthernet instance Comware Related ProVision display stp bpdu-statistics show spanning-tree detail display stp bpdu-statistics interface GigabitEthernet display stp bpdu-statistics interface GigabitEthernet instance Displays the debug counters of the STP in different modes.
PAGE 288
Example of Related ProVision Software Command Output. HP Switch# show spanning-tree detail Status and Counters - CST Port(s) Detailed Information Port : 1 Status : Up ...
PAGE 289
display stp briefdisplay stp instance briefdisplay stp instance interface GigabitEthernet briefdisplay stp instance interface GigabitEthernet briefdisplay stp instance interface GigabitEthernet to GigabitEthernet briefdisplay stp instance slot briefdisplay stp interface GigabitEnterface briefdisplay stp interface GigabitEnterface to GigabitEnterfac
PAGE 290
Port Type | Cost ---- ---- + ---1 10/100TX | Auto 2 10/100TX | Auto 3 10/100TX | Auto . . . . . . . . . 7 10/100TX | Auto rity Edge Edge PtP Time Grd Grd Flt ---- ---- ----- ---- ----- ---- ---- --128 No Yes True Global No No No 128 No Yes True Global No No No 128 No Yes True Global No No No . . 128 No Yes True Global No No No ProVision accepts interface range as 1-8. Comware accpets interface range as "GigabitEthernet1/0/1 to GigabitEthernet1/0/8".
PAGE 291
display stpdisplay stp instance interface GigabitEthernet 1/0/1/display stp slot Comware Related ProVision display stp show spanning-tree display stp instance interface GigabitEthernet 1/0/1/ display stp slot Displays MSTP status and statistics. HP Switch# display stp Protocol Status : Protocol Std. : Version : CIST Bridge-Prio : MAC Address : Max age (s) : Forward delay (s) : Hello Time(s) : Max Hops : Disabled IEEE802.
PAGE 292
7 8 100/1000T | Auto 128 Disabled | 100/1000T | Auto 128 Disabled | For more information, see the latest Advanced Traffic Management Guide for your switch.
PAGE 293
display stp down-port Comware Related ProVision display stp down-port No equivalent ProVision software command Displays information about ports shut down by spanning tree protection functions. HP Switch# display stp down-port Down Port Reason 4 BPDU-Protected 5 BPDU-Protected Operating Notes ProVision does not support Format-Frequency.
PAGE 294
display stp history display stp history slot display stp instance history slot display stp instance history Comware Related ProVision display stp history No equivalent ProVision software command display stp history displays the historical port role calculation information of all MSTIs. display stp history slot slot-number displays the statistics of the port’s history information of all the MSTIs of a given slot when stp protocol is enabled.
PAGE 295
display stp instance tcdisplay stp instance tc slot display stp tc Comware Related ProVision display stp instance tc No equivalent ProVision software command display stp instance tc slot display stp tc Displays the STP information of a port under a particular instance when STP is enabled.
PAGE 296
display stp region-configuration Comware Related ProVision display stp region-configuration show spanning-tree mst-config show spanning-tree mst-config Spanning-tree protocol is enabled HP Switch# display stp region-configuration Oper Configuration Format selector :0 Region name :hello Revision level :0 Configuration digest :0x5f762d9a46311effb7a488a3267fca9f Instance Vlans Mapped 0 21 to 4094 1 1 to 10 2 11 to 20 Spanning-tree protocol is diabled HP Switch# display stp region-configuration Oper configu
PAGE 297
display stp root Comware Related ProVision display stp root show spanning-tree instance show spanning-tree detail Displays the root bridge information of all MSTIs. Spanning-tree protocol is enabled HP Switch# display stp root MSTID Root Bridge ID ExtPathCost IntPathCost Root Port 0 00e0fc-0e6554 200200 0 A1 Spanning-tree protocol is disabled HP Switch# display stp root HP Switch# Example of Related ProVision Software Command Output.
PAGE 298
display switchover state Comware Related ProVision display switchover state show redundancy Displays the backup state of the specified main board. This command displays the backup state on the AMB or the standby main board (SMB) depending on the slot number specified. The backup state of the AMB is displayed if no slot number is specified.
PAGE 299
display switchover state Field Mappings.
PAGE 300
display system-failure Comware Related ProVision display system-failure show boot-history HP Switch# display system-failure System failure handling method: reboot Example of Related ProVision Software Command Output. HP Switch# show boot-history Mgmt Module 1 -- Saved Crash Information (most recent first): ============================================================= Mgmt Module 1 in Active Mode went down: 11/07/09 14:48:36 Operator warm reload from CONSOLE session.
PAGE 301
display this Comware Related ProVision display this No equivalent ProVision software command Displays valid configuration information under the current view. Use this command to check whether your configuration has taken effect. Valid configuration that is the same as the default is not displayed. Invalid configuration is not displayed. Execution of this command in any user interface view displays the valid configuration in all the user interfaces.
PAGE 302
display transceiver alarm interface Comware Related ProVision display transceiver alarm interface show interface transceiver detail Displays the current alarm information of a single or all transceivers. HP Switch(config)# display transceiver alarm interface g1 G1 transceiver current alarm information: Rx power low Field Descriptions RX loss of signal: Incoming (RX) signal is lost. TX fault: Transmit (TX) fault RX power high: Incoming (RX) power level is high.
PAGE 303
Temp high: Temperature is high. Temp low: Temperature is low. Voltage high: Voltage is high. Voltage low: Voltage is low. Transceiver info I/O error: Transceiver information read and write error Transceiver info checksum error: Transceiver information checksum error Transceiver type and port configuration mismatch: Transceiver type does not match port configuration. Transceiver type not supported by port hardware: Transceiver type is not supported on the port.
PAGE 304
• TX power high • TX power low • RX power high • RX power low • Transceiver info I/O error • Transceiver info checksum error • Transceiver type and port configuration mismatch • Transceiver type not supported by port hardware • RX loss of signal • TX fault For more information on transceivers, see the "Troubleshooting" chapter in the latest Management and Configuration Guide for your switch. Example of Related ProVision Software Command Output.
PAGE 305
Comware ProVision Software Module not ready n/a APD supply fault n/a TEC fault n/a Wavelength unlocked n/a Temp high Temp high Temp low Temp low Voltage high Voltage high Voltage low Voltage low TX bias high TX bias high TX bias low TX bias low TX power high TX power high TX power low TX power low RX power high RX power high RX power low RX power low RX loss of signal RX loss of signal TX fault TX fault display transceiver alarm interface 305
PAGE 306
display transceiver diagnosis interface Comware Related ProVision display transceiver diagnosis interface show interface transceiver [ | detail ] Displays the currently measured value of digital diagnosis parameters of H3C customized anti-spoofing pluggable optical transceivers. HP Switch(config)# display transceiver diagnosis interface g1 G1 transceiver diagnostic information: Current diagnostic parameters: Temp.(C) Voltage(V) Bias(mA) RX power(dBM) TX power(dBM) 25.000 0.0000 7.864 -inf -2.
PAGE 307
Rx loss of signal Time Stamp : Mon Jun 11 03:00:27 2012 display transceiver diagnosis interface Field Mappings. Comware ProVision Software transceiver diagnostic information Transceiver in Current diagnostic parameters Status Temp.
PAGE 308
display transceiver interface Comware Related ProVision display transceiver interface show interface transceiver [ | detail ] Displays main parameters of a single or all pluggable transceivers.
PAGE 309
Operating Notes For more information on transceivers, see the "Troubleshooting" chapter in the latest Management and Configuration Guide for your switch. Example of Related ProVision Software Command Output. HP Switch(config)# sh int transceiver 24 detail Transceiver in 24 Interface Index : 124 Type : SFP+LR Model : J9151A Connector Type : LC Wavelength : 1310nm Transfer Distance : 10.0km (9um), Diagnostic Support : DOM Serial Number : CN847GV009 Status Temperature : 35.148C Voltage : 3.2348V Tx Bias : 41.
PAGE 310
display transceiver manuinfo interface Comware Related ProVision display transceiver manuinfo interface show interface transceiver [ | detail ] Displays the transceiver manufacturing information of the specified transceiver on an interface or of all the interfaces in the device. HP Switch(config)# display transceiver manuinfo interface g1 G1 transceiver manufacture information: Manu. Serial Number : MY902IF107 Manufacturing Date : 081118 Vendor Name : n/a Field Descriptions Manu.
PAGE 311
display transceiver diagnosis manuinfo Field Mappings. Comware ProVision Software Manu.
PAGE 312
display user-bind Comware Related ProVision display user-bind show ip source-lockdown bindings Displays user bind address. HP Switch# display user-bind Total entries found: 1 MAC IP Vlan Port Status 0030c1-7f49c0 120.93.49.7 2 1 Example of Related ProVision Software Command Output. HP Switch# show ip source-lockdown bindings Dynamic IP Lockdown (DIPLD) Bindings Mac Address IP Address VLAN Port Not in HW ----------- ---------- ----- ----- --------001122-334455 10.10.10.1 1111 X11 005544-332211 10.10.10.
PAGE 313
display vlan Comware Related ProVision display vlan No equivalent ProVision software command Displays vlan-id for the existing vlan only. If it is consecutive it displays as a range. HP Switch# display vlan Total 2 VLAN exist(s). The following VLANs exist: 1(default), 7, HP Switch# display vlan static Total 2 VLAN exist(s).
PAGE 314
display vrrp Comware Related ProVision display vrrp show vrrp NOTE: This command is not supported on the HP 2920 Series switches. Displays vrrp details like VLAN, status, priority, and router ip address. HP Switch# display vrrp IPv4 Standby Information: Run Mode : Standard Run Method : Virtual MAC Total number of virtual routers : 2 Interface VRID State Run Adver Auth Virtual Pri Timer Type IP ------------------------------------------------------------Vlan4 4 Initialize 144 1 None 14.4.1.
PAGE 315
VRRP Enabled : Yes Traps Enabled : Yes Virtual Routers Respond to Ping Requests : Yes VRRP Nonstop Enabled: Yes VRRP Virtual Router Configuration Information Vlan ID : 10 Virtual Router ID : 1 Administrative Status [Disabled] : Enabled Mode [Uninitialized] : Backup Priority [100] : 150 Advertisement Interval [1] : 1 Preempt Mode [True] : True Preempt delay time : 0 Respond to Virtual IP Ping Requests [Yes] : Yes Primary IP Address : Lowest IP Address Subnet Mask --------------- --------------10.0.202.
PAGE 316
display vrrp interface vrid Comware Related ProVision display vrrp interface vrid show vrrp vrid NOTE: This command is not supported on the HP 2920 Series switches.
PAGE 317
display vrrp statistics Comware Related ProVision display vrrp statistics show vrrp statistics NOTE: This command is not supported on the HP 2920 Series switches. Displays vrrp counters like invalid type packets received, priority zero packets received and sent on each vrrp router configured.
PAGE 318
Protocol Version : 2 Invalid VRID Pkts Rx : 0 Checksum Error Pkts Rx : 0 Bad Version Pkts Rx : 0 For more information, see the the latest Multicast and Routing Guide for your switch.
PAGE 319
display vrrp statistics interface vrid Comware Related ProVision display vrrp statistics interface vrid show vrrp statistics global NOTE: This command is not supported on the HP 2920 Series switches. Displays statistics about VRRP group(s). If you specify both an interface and a VRRP group, only the statistics about the specified VRRP group on the interface are displayed.
PAGE 320
display vrrp verbose Comware Related ProVision display vrrp verbose show vrrp NOTE: This command is not supported on the HP 2920 Series switches. Displays detailed state information of VRRP group(s). If you specify both an interface and a VRRP group, only the state information of the specified VRRP group on the interface is displayed. If you only specify an interface, the state information of all the VRRP groups on the interface is displayed.
PAGE 321
Virtual Router ID : 1 State : Master Up Time : 25 secs Virtual MAC Address : 00005e-000101 Master's IP Address : 10.0.102.87 Associated IP Addr Count : 1 Near Failovers : 0 Advertise Pkts Rx : 0 Become Master : 1 Zero Priority Rx : 0 Zero Priority Tx : 0 Bad Length Pkts : 0 Bad Type Pkts : 0 Mismatched Interval Pkts : 0 Mismatched Addr List Pkts : 0 Mismatched IP TTL Pkts : 0 Mismatched Auth Type Pkts : 00 For more information, see the latest Multicast and Routing Guide for your switch.
PAGE 322
3 Fundamental Commands backup startup-configuration Comware Related ProVision backup startup-configuration copy startup-config tftp Used to backup the startup configuration file (used at the next system startup) to a specified TFTP server and to a specified filename. HP Switch# backup startup-configuration to 120.93.49.9 test_new TFTP download in progress. Related ProVision Software Command.
PAGE 323
clock datetime Comware Related ProVision clock datetime clock set Used to set the current time and date of the device. You can leave the ss field blank when you specify the time parameters. This command accepts any input for the YYYY value. It displays the current time once the value is set. It displays a warning string if it is executed in Manager View. It is not available in Operator View, it is only available in Configure context.
PAGE 324
clock summer-time one-off Comware Related ProVision clock summer-time clock summer-time This command does not differ from the related ProVision software command. HP Switch# clock summer-time Operating Notes For more information, refer to the latest Command Line Interface Reference Guide for your switch. Minimum Software Version: 15.10.
PAGE 325
clock summer-time repeating Comware Related ProVision clock summer-time repeating clock summer-time This command does not differ from the related ProVision software command. HP Switch# clock summer-time Operating Notes For more information, refer to the latest Command Line Interface Reference Guide for your switch. Minimum Software Version: 15.10.
PAGE 326
clock timezone Comware Related ProVision clock timezone clock timezone This command does not differ from the related ProVision software command. HP Switch# clock timezone Operating Notes For more information, refer to the latest Command Line Interface Reference Guide for your switch. Minimum Software Version: 15.10.
PAGE 327
command accounting Comware Related ProVision command accounting aaa accounting commands < stop-only | interim-update > radius Used to enable command accounting. HP Switch# command accounting Related ProVision Software Command. HP Switch# aaa accounting commands Operating Notes For more information, refer to the latest Access Security Guide for your switch. Minimum Software Version: 15.10.
PAGE 328
command authorization Comware Related ProVision command authorization aaa authorization commands radius Used to enable command authorization. HP Switch# command authorization Related ProVision Software Command. HP Switch# aaa authorization commands radius Operating Notes For more information, refer to the latest Access Security Guide for your switch. Minimum Software Version: 15.10.
PAGE 329
command-alias enable Comware Related ProVision command-alias enable No equivalent ProVision software command Used to enable the command keyword alias function. By default, the command keyword alias function is enabled. HP Switch# command-alias enable Minimum Software Version: 15.10.
PAGE 330
command-alias mapping Comware Related ProVision command-alias mapping No equivalent ProVision software command Used to configure a command keyword alias. By default, a command keyword has no alias. By default, the command is enabled and not configurable. It is available in Manger view. It accepts "any string" (irrespective of whether it’s a valid command token or not). Cmdkey value range is 1-40 and AliasKey value range is 1-32. HP Switch# command-alias mapping Minimum Software Version: 15.10.
PAGE 331
copy Comware Related ProVision copy copy config SOURCE_CONFIG_FILE_ON_SWITCH config DESTINATION_CONFIG_FILE_ON_SWITCH This command does not differ from the related ProVision software command. HP Switch# copy config SOURCE_CONFIG_FILE_ON_SWITCH config DESTINATION_CONFIG_FILE_ON_SWITCH Operating Notes For more information, refer to the latest Management and Configuration Guide for your switch. Minimum Software Version: 15.10.
PAGE 332
delete Comware Related ProVision delete erase config Used to delete config file from the system directory. This command can be executed from any context. The keyword 'delete' tab help text lists the config files which can be deleted. The command allows only deletion of config files and not other files. It does not support wildcards (like *.txt) and file names with URL’s. Deleted files cannot be restored.
PAGE 333
flow-control Comware Related ProVision flow-control flow-control This command does not differ from the related ProVision software command. HP Switch# flow-control Operating Notes For more information, refer to the latest Management and Configuration Guide for your switch. Minimum Software Version: 15.10.
PAGE 334
idle-timeout Comware Related ProVision idle-timeout console inactivity-timer Used to set the idle-timeout timer. When it expires, user sessions are terminated. By default idle-timeout is disabled. The command supports only minutes. And these minutes are the predefined set 0,1,5,10,15,20,30,60,120. The command is available in configure context. The default inactivity timer is 0 and means it is disabled. HP Switch# idle-timeout 120 Related ProVision Software Command.
PAGE 335
quit Comware Related ProVision quit exit Used to return to a lower-level view. If the current view is operator mode, this command terminates the current connection and quits the system. HP Switch# quit Do you want to log out [y/n]? Related ProVision Software Command. HP Switch# exit Operating Notes For more information, refer to the latest Basic Operation Guide for your switch. Minimum Software Version: 15.10.
PAGE 336
reboot Comware Related ProVision reboot slot boot Used to reboot a module. If the slot keyword is not provided, the whole system reboots. HP Switch# reboot slot A Related ProVision Software Command. HP Switch# boot Operating Notes For more information, refer to the latest Management and Configuration Guide for your switch. Minimum Software Version: 15.10.
PAGE 337
reset saved-configuration Comware Related ProVision reset saved-configuration erase startup Used to delete the startup configuration file saved on the storage medium of the switch. The command can be executed in manager mode. Related ProVision Software Command. HP Switch# erase startup Operating Notes For more information, refer to the latest Management and Configuration Guide for your switch. Minimum Software Version: 15.10.
PAGE 338
restore startup-configuration Comware Related ProVision restore startup-configuration copy tftp startup-config Used to download a configuration file from the specified TFTP server to the switch and specify the configuration file as the startup configuration file to be used at the next startup of the switch. The command is supported in manager mode.
PAGE 339
return Comware Related ProVision return end Used to return to user view from current view (non user view), as with the hot key ctrl+Z. HP Switch# return Related ProVision Software Command. HP Switch# end Operating Notes For more information, refer to the latest Management and Configuration Guide for your switch. Minimum Software Version: 15.10.
PAGE 340
save Comware Related ProVision save write memory Used to save the current configuration to the current startup config file. By default, the current configuration gets saved in the current start-up configuration file. Related ProVision Software Command. HP Switch# write memory Operating Notes For more information, refer to the latest Management and Configuration Guide for your switch. Minimum Software Version: 15.10.
PAGE 341
schedule reboot at Comware Related ProVision schedule reboot at reload at Used to enable the scheduled reboot function of the whole system (including all cards) at a specific time and date. The command can be executed in manager mode. The supported date form is mm/dd[/[yy]yy]. The command cannot be executed if the date is not specified and specified reboot time is earlier than the current time.
PAGE 342
schedule reboot delay Comware Related ProVision schedule reboot delay reload after Used to enable the scheduled reboot function of the whole system (including all cards) and to set a reboot waiting time. The command can be executed in manager mode and accepts input in [[dd:]hh:]mm format. HP Switch# schedule reboot delay 01:20 Reload scheduled in 0 days, 1 hours, 20 minutes System will be rebooted at the scheduled time from secondary image.
PAGE 343
screen-length Comware Related ProVision screen-length terminal length Used to set the number of lines on the next screen. This command is executed in manager mode. The range for the number of lines supported is 2-1000. HP Switch# screen-length Related ProVision Software Command. HP Switch# terminal length Operating Notes For more information, refer to the latest Basic Operation Guide for your switch. Minimum Software Version: 15.10.
PAGE 344
set authentication password Comware Related ProVision set authentication password set authentication password This command does not differ from the related ProVision software command. HP Switch# set authentication password Operating Notes For more information, refer to the latest Command Line Interface Reference Guide for your switch. Minimum Software Version: 15.10.
PAGE 345
speed Comware Related ProVision speed (user interface view) console baud-rate Used to set the transmission rate on the user interface. This command can be executed from configure mode. There is no default value. The lowest supported value is 1200 bps. The configuration has to be saved and the switch has to be rebooted to make the configuration effective. HP Switch# speed 9600 This command will take effect after saving the configuration and rebooting the system. Related ProVision Software Command.
PAGE 346
startup saved-configuration Comware Related ProVision startup saved-configuration startup-default config Used to specify the configuration file to be used at the next system startup. This command can be executed in manager mode. HP Switch# startup saved-configuration test This will change the default configuration file to be used whenever the switch is rebooted. Continue [y/n]? Related ProVision Software Command.
PAGE 347
sysname Comware Related ProVision sysname hostname Used to set the name of the device. Changing device name affects the prompt of the CLI. For example, if the device name is Sysname, the prompt of the user view is . Special characters are not allowed. HP Switch# sysname Related ProVision Software Command. HP Switch# hostname Operating Notes For more information, refer to the latest Basic Operation Guide for your switch. Minimum Software Version: 15.10.
PAGE 348
system-view Comware Related ProVision system-view configure terminal Used to enter system view from the current user view. HP Switch# system-view HP Switch(config)# Related ProVision Software Command. HP Switch# configure terminal HP Switch(config)# Operating Notes For more information, refer to the latest Basic Configuration Guide for your switch. Minimum Software Version: 15.10.
PAGE 349
telnet Comware Related ProVision telnet telnet This command does not differ from the related ProVision software command. HP Switch# telnet Operating Notes For more information, refer to the latest Management and Configuration Guide for your switch. Minimum Software Version: 15.10.
PAGE 350
telnet ipv6 Comware Related ProVision telnet ipv6 telnet Used to telnet to a remote IPv6 host. To stop the current Telnet login, press Ctrl+K or use the quit command. This command supports both ipv6 and ipv4 formats with the given string name. HP Switch# telnet ipv6 hostname HP Switch# telnet ipv6 addr Related ProVision Software Command. HP Switch# telnet hostname Operating Notes For more information, refer to the latest Basic Configuration Guide for your switch. Minimum Software Version: 15.10.
PAGE 351
telnet server enable Comware Related ProVision telnet server enable telnet-server Used to enable the Telnet server. The Telnet server is enabled by default. This command is executed in manager mode. HP Switch# telnet server enable Related ProVision Software Command. HP Switch# telnet-server Operating Notes For more information, refer to the latest Basic Configuration Guide for your switch. Minimum Software Version: 15.10.
PAGE 352
terminal type Comware Related ProVision terminal type console terminal Used to configure the type of terminal display under the current user interface. By default, the terminal display type is VT100. This command can be executed in manager mode. The configuration becomes effective after it is saved and the system is rebooted. HP Switch# terminal type ansi This command will take effect after saving the configuration and rebooting the system. Related ProVision Software Command.
PAGE 353
tftp Comware Related ProVision tftp copy Used to download a specified file from the TFTP server to the local device or upload a specified local file to the TFTP server in an IPv4 network. This command can be executed only from config context. Downloading a file from the tftp server to any user given file or uploading any file to the tftp server is supported only for specific type of files. Comware command allows . In ProVision this functionality is supported only for specific type of files.
PAGE 354
tftp ipv6 Comware Related ProVision tftp ipv6 copy Used to download a specified file from a TFTP server or upload a specified local file to a TFTP server in an IPv6 network. This command can be executed only from config context. Downloading a file from the tftp server to any user given file or uploading any file to the tftp server is supported only for specific type of files. Comware command allows . In ProVision this functionality is supported only for specific type of files.
PAGE 355
undo Comware Related ProVision undo no vlan vlan-id Used to reset the configuration of the system. HP Switch# undo vlan vlan-id Related ProVision Software Command. HP Switch# no vlan vlan-id Operating Notes For more information, refer to the latest Command Line Interface Reference Guide for your switch. Minimum Software Version: 15.10.
PAGE 356
4 Comware Configuration Help Commands Table of Comware Commands and Associated ProVision Commands Comware Configuration Command ProVision Command ProVision Command Location(s) HP Switch(config)# acl See ip access-list, ipv6 access-list or access-list Access Security GuideIPv6 Configuration Guide HP Switch(config)# acl step Specify the index when creating the entry Access Security Guide HP Switch(config)# arp check See ip arp-mcast-replies Multicast and Routing Guide HP Switch(config)# arp timer
PAGE 357
Comware Configuration Command ProVision Command ProVision Command Location(s) HP Switch(eth-1)# dot1x See aaa port-access authenticator Access Security Guide HP Switch(config)# fips See secure mode Access Security Guide HP Switch(config)# hwtacacs See tacacs-server Access Security Guide HP Switch(vlan-1)# igmp See vlan ip igmpComware supports L3 IGMP (snooping and routing) in interface VLAN context and L2 IGMP (snooping) in VLAN context.
PAGE 358
Comware Configuration Command ProVision Command ProVision Command Location(s) HP Switch(config)# policy-based-route See class or policy Advanced Traffic Management Guide HP Switch(eth-1)# proxy-arp See ip proxy-arp Multicast and Routing Guide HP Switch(config)# qos apply See class or policy Advanced Traffic Management Guide HP Switch(config)# qos policy See class or policy Advanced Traffic Management Guide HP Switch(config)# radius server RADIUS configuration is executed at Access Security G
PAGE 359
Comware Configuration Command ProVision Command ProVision Command Location(s) HP Switch(config)# spanning-tree root-protection See spanning-tree root-guard Advanced Traffic Management Guide HP Switch(config)# spanning-tree tc-protection See spanning-tree tc-end-guard Advanced Traffic Management Guide HP Switch(config)# stp See spanning-tree Advanced Traffic Management Guide HP Switch(config)# system-view help Use the command comware-help This Guide for more information about differences between
PAGE 360
Enabling SSH To enable SSH connectivity to your ProVision switch, issue the ip ssh command. If SSH has never been enabled on the ProVision switch, you may also need to issue the crypto key generate ssh command before issuing the ip ssh command. To disable the TELNET server on the ProVision switch, issue the no telnet-server command. Ports and VLANs On ProVision, fixed-port Ethernet ports on the front of the switch are assigned a number.
PAGE 361
Index A aaa accounting commands, 327, 328 aaa port-access authenticator, 357 aaa port-access mac-based, 356, 357 access-list, 356 acl, 356 acl step, 356 alias, show, 28 arp check, 356 arp detection statistics, display, 23 arp detection statistics, show, 23 arp ip-address, display, 24 arp time, 356 B backup startup-configuration, 322 BGP, 108, 111 bgp, 356 boot set-default flash, 25 boot system, 25 boot-history, show, 300 boot-loader, display, 25 bridge-aggregation, 356 broadcast-suppression, 356 C class,
PAGE 362
fields, not populated, 16 fips, 357 flash, show, 25 flow-control, 333 G gvrp status, display, 81 gvrp vlan-operation interface interface-type interface-number, display, 82 gvrp, show, 81 H history, show, 83 history-command, display, 83 HP Networking switch documentation, 13 hwtacacs, 357 I idle-timeout, 334 igmp, 357 igmp group interface vlan-interface verbose, display, 89 igmp group verbose, display, 93 igmp group x.x.x.
PAGE 363
O ospf, 357 ospf interface, display, 191 ospf routing, display, 197 ospf vlink, display, 198 ospfv3, 357 ospfv3 lsdb statistics, display, 210 ospfv3 lsdb, display, 208 ospfv3 peer statistics, display, 215 ospfv3 vlink, display, 220 ospfv3, display, 200 output differences, 16 output, empty, 17 P packet-filter, 357 pim, 357 pim control-message counters, display, 224 pim grafts, display, 225 pim join-prune, display, 230 pim routing-table, display, 235 pim rp-info, display, 236 poe device, display, 237 poe int
PAGE 364
spanning-tree active, 358 spanning-tree admin-edge, 358 spanning-tree compliance; spanning-tree legacy-mode, 358 spanning-tree config-name, 358 spanning-tree edged-port, 358 spanning-tree legacy-mode, 358 spanning-tree mode, 358 spanning-tree pending-apply, 358 spanning-tree region-name, 358 spanning-tree root-guard, 359 spanning-tree root-protection, 359 spanning-tree tc-end-guard, 359 spanning-tree tc-protection, 359 speed, 345 ssh server session, display, 277 ssh server-info, display, 279 ssl client-poli