FibrChanl-02 (fclp) Fibre Channel Mass Storage Driver for HP-UX 11i v3 Release Notes Version Number B.11.31.0906 HP Part Number: J4301-90016_e3 Published: June 2009 Edition: 3.
Table of Contents FibrChanl-02 (fclp) Fibre Channel Mass Storage Driver for HP-UX 11i v3 Overview..........................5 New and Changed Features in This Release..........................................................................................5 New Features.....................................................................................................................................5 Known Problems Fixed in This Version........................................................................
List of Tables 1 2 3 4 5 4 HP-UX June 2009 Fixes....................................................................................................................5 HP-UX March 2009 Fixes................................................................................................................5 HP-UX December 2008 Fixes..........................................................................................................5 HP-UX September 2008 Fixes.................................................
This document provides information about the B.11.31.0906 release of the FibrChanl-02 (fclp) Fibre Channel Mass Storage Driver for HP-UX 11i v3. FibrChanl-02 (fclp) Fibre Channel Mass Storage Driver for HP-UX 11i v3 Overview This release of the FibrChanl-02 (fclp) Fibre Channel Mass Storage Driver for HP-UX 11i v3 (version B.11.31.0906) fixes a defect. New and Changed Features in This Release New Features There are no new features in this release.
NOTE: AR0803 was the initial release of FibrChanl-02 (fclp) on HP-UX 11i v3. Known Problems and Limitations This section provides a list of known problems and limitations as known to HP at time of publication. If workarounds are available, they are included. • Crash Dump Fails through Dual Ported fclp Card when Dump Devices are Configured through Both Ports The workaround is to configure the dump devices through single-ported fclp cards only.
This issue is addressed in system firmware version 3.01 for rx2660, rx3600, and rx6600. There are three workarounds for this issue: 1. 2. 3. • Return to the Boot Manager, enter and exit the EFI shell a second time, and retry the boot; or, Reset the system and retry the boot; or, Configure the EFI driver to always map the boot devices using the drvcfg -s at the EFI shell prompt.
7. 8. 9. • Select (highlight) the Force Link Speed option and press Enter. Select (highlight) the 2Gb/s link speed option from the list presented, and press Enter. After completing your selection, use the ESC key to exit the EFI configuration menus.
Table 5 Recommended Firmware/EFI Versions (June 2009) (continued) Fibre Channel Adapter EFI Driver Version Firmware Version Universal Boot Code 456972-B21 6.03A7 or later 1.10A5 or later 6.03A7 AD355A, AD299A 3.21A3 or later 2.70X5 or later N/A AD221A, AD222A, AD393A 3.21A3 or later 2.72A2 or later N/A 403621-B21 4.00A1 or later 2.72A2 or later 6.00A5 For current recommended firmware versions, see the HP Fibre Channel Host Bus Adapter Support Matrix at http://docs.hp.com/en/netcom.
It is not possible to update previous recipes/versions of the Mezzanine card to be compatible with the HP Integrity blades. Identification The following are the ways to identify the versions of the cards that are compatible with Integrity c-Class blades. EDC Change The newer cards are built with an Engineering Date Code that marks the changes required for Integrity — Integrity-supported versions have an EDC of B-4813 or later.
Part Serial number : "MY18071ZYV" Engineering Date Code : "B-4813" Mfd. Date : "4807" Misc. Information : "PW=6.5W; PCIe x4 Gen1" ROM Firmware version : "2.72A2 SLI-3 (Z3F2.72A2)" EFI version : "ZU6.00A5" Card Revision Although EDC is the primary way to identify changes in recipe for Integrity systems, it is also possible to use the card “Rev”, which is printed on a label on the box containing the card, and on a label on the card.
Related Information The latest documentation for the FibrChanl-02 (fclp) Fibre Channel Mass Storage Driver for HP-UX 11i v3 is available at http://www.docs.hp.com, under the I/O Cards and Networking Software section in the Fibre Channel category. Available documents include: • • • • Support Guide: includes an adapter overview, installation details, adapter configuration, troubleshooting and maintenance information, additional features, and regulatory information.
