HP MSM7xx Controllers Release Notes v6.2.1.
© Copyright 2014 Hewlett-Packard Development Company, L.P. The information contained herein is subject to change without notice. The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty. HP shall not be liable for technical or editorial errors or omissions contained herein. Acknowledgements Windows® is a U.S.
Version: MSM v6.2.1.0 Description These Release Notes provide important release-related information. NOTE: In this document, except when identifying specific models, the generic term “controller” is used in place of MSM7xx Controller product names and the generic term “AP” is used in place of MSM3xx / MSM4xx / HP 425 Access Point product names.
NOTE: Due to a problem with AP channel use validation, a banner similar to this may appear at the top of the Home screen: AP CNxxxxxxxx, Radio 1 channel configuration has been set to autochannel because the previously configured channel Auto is not supported by this version of software. The same message is added to the system log. These messages can be safely ignored.
RF Manager software and MSM software version compatibility RF Manager versions 5.9.x, 6.0.x, and 6.7.x work with MSM software version 5.5.x and higher. However, to use the WLAN Integration feature in RF Manager 6.0.x or 6.7.x, the RF Manager and MSM software versions must be matched as follows: MSM7xx software version 6.2.0.x/6.2.1.0 Compatible RF Manager versions 6.0.185, 6.7.769 or later 5.7.1.x/5.7.2.0/6.0.0.1/6.0.1.x 6.0.177 or later 5.7.0.2/5.7.0.3/5.7.0.4 6.0.162 or later 5.5.3.x 6.0.
Configuring the service controller in GMS (when teaming is used): • Do not configure a controller in GMS when the team manager controller is not available and a team member is temporarily taking its place. • GMS interacts only with the team manager controller, you cannot add a team member as the controller. • Any attempt to add a team member as a service controller in GMS will be rejected, with the following message displayed: An error occurred while uploading the CA to the Service Controller.
Although enabled in MSM software release 6.2.0.0, the following SOAP functions should not be used on a controller team. If you attempt to use any of these functions when teaming is enabled, an error is returned.
• Configuration backup using IMC fails for all MSM devices. • The firmware updates feature does not work properly. • The following misleading error message has been removed: debug webredirect: SSL Error occurred while reading: error:140760FCSL routines: SL23_GET_CLIENT_HELLO:unknown protocol (336027900) • When a controller location is set to Morocco, APs can fail to synchronize when a radio is set to 802.11n and the 5 GHz band is being used for local mesh.
GetVirtualSC8021XStationIdDelimiterAndCase ◦ To configure the MAC case: GetVirtualSC8021XStationIdDelimiterAndCasem UpdateVirtualSC8021XStationIdDelimiterAndCasem nl nl • When configuring Wireless protection with a Key source of Preshared Key, the station delimiter and station ID MAC delimiter configuration fields are disabled. • The MSM7xx Controller does not provide a NAS ID value to a customized ACL. • (Applies to teaming.
• When a VLAN is configured as an egress VLAN and also to be monitored by IDS, wireless traffic is blocked. • (Applies to teaming.) When a MAC list is deleted from a team member controller, the team member controller may experience a reboot and the APs are synchronized to the team manager. • (Applies to teaming.) When using teaming and WPA termination at the controller, wireless clients that are connected through a team member controller might not get a DHCP lease.
• (Applies to MSM410, HP 425, MSM430, MSM460, MSM466, MSM466-R.) When Intrusion Detection System (IDS) is enabled, AP radios on that (team of) controller(s) should not be configured in Access Point and Local Mesh or Local Mesh only. As a workaround, IDS must be disabled on the controller if Access Point and Local Mesh or Local Mesh only operation is required. • (Applies to MSM422.
