abg The HP 501 is a Wi-Fi Alliance authorized Wi-Fi CERTIFIED n ac 802.11a/b/g/n/ac product. The Wi-Fi CERTIFIED Logo is a In certification mark of the Wi-Fi Alliance. HP 501 802.11ac Wireless Client Bridge Quickstart This Quickstart shows you how to install and get started using the HP 501 (J9835A) 802.11ac Wireless Client Bridge, hereafter referred to as the HP 501. The latest documentation, including the HP 501 802.
HP 501 802.11ac Wireless Client Bridge Quickstart 2 Package contents Important information to read before installing LED The HP 501 Wireless Client Bridge, mounting bracket, two spring clips, three dual-band omnidirectional antennas, two mounting screws with wall anchors, one cable tie, and documentation. Ethernet Ports • Ethernet port: Auto-sensing 1000 BaseT Ethernet port with RJ-45 connector. The port supports IEEE 802.3af Power over Ethernet (PoE).
HP 501 802.11ac Wireless Client Bridge Quickstart Surge protection and grounding: When connecting antennas installed outdoors to the HP 501, make sure that proper lightning surge protection and grounding precautions are taken according to local electrical code. Failure to do so can result in personal injury, fire, equipment damage, or a voided warranty. The HP hardware warranty provides no protection against damage caused by static discharge or a lightning strike.
HP 501 802.11ac Wireless Client Bridge Quickstart 4 Mounting on a wall or ceiling 1. Hold the mounting bracket against the wall or ceiling where it will be installed. Mark two holes for the screws (wall anchors). 2. Drill two holes for the wall anchors, typically 4.7 mm (3/16 inch) in Installation Placing on a desktop The HP 501 can also be installed on a desktop using the mounting bracket. Slide the HP 501 base onto the mounting bracket, and then place it on the desktop in the preferred location.
HP 501 802.11ac Wireless Client Bridge Quickstart 5 Initial configuration Initial configuration • If using an AC/DC adapter, connect it to the power connector on the HP 501. This procedure describes how to perform initial configuration for a factorydefault HP 501. For illustration purposes, a simple scenario is used. In this scenario, the HP 501 links a wired computer to a private network through a wireless connection to an AP. For instructions on how to configure other scenarios, see the HP 501 802.
HP 501 802.11ac Wireless Client Bridge Quickstart D. Assign an IP address to the HP 501 By default, the HP 501 operates as a DHCP client. This means that if the network has a DHCP server, the HP 501 automatically receives a new IP address in place of its default address of 192.168.1.1 upon connecting to the network. Use one of the following methods to assign an IP address to the HP 501: 6 Initial configuration the SSID directly, be sure to configure the same name as on the private network AP.
HP 501 802.11ac Wireless Client Bridge Quickstart 7 3. Reconnect power to the HP 501. 4. Reconnect your computer to the HP 501. 5. Confirm that your wireless network interface is still disabled (it was disabled during an earlier configuration step). 6. Enable the Ethernet network interface of your computer, and verify that it is set to obtain an IP address automatically from DHCP. G.
HP 501 802.11ac Wireless Client Bridge Quickstart 8 Other regulatory information When this device is operated in 5.15~5.25 GHz frequency range, it is restricted to indoor use only. The device for the band 5150-5250 MHz is only for indoor usage to reduce the potential for harmful interference to co-channel mobile satellite systems. This device will not permit operation on channels 120-128 for 11a, 11n, and 11ac modes that overlap the 5600-5650 MHz band.
HP 501 802.11ac Wireless Client Bridge Quickstart Belarus Kazakhstan Russia marking Manufacturer and Local Representative Information Manufacturer’s information: • Hewlett-Packard Company, 3000 Hanover Street, Palo Alto, California 94304, U.S. Local Representative information Russian: • HP Belarus: ИООО «Хьюлетт-Паккард Бел», 220030, Беларусь, г. Минск, ул. Интернациональная, 36-1, офис 722-723, тел.
HP 501 802.11ac Wireless Client Bridge Quickstart 10 Other regulatory information Specification Description Radio Channel bandwidth supported 20, 40, and 80 MHz FCC Part 15.247; EN 300 328; FCC Part 15.407; MIC Notice No. 88, App. 43 & 45; EN 301 893; RSS-210 Spatial streams 3 (3x3 configuration) Safety Also support 1 and 2 streams modes UL 2043; UL 60950-1; EN 60950-1; CAN/CSA-C22.2 No. 60950-1 802.11b: 1, 2, 5.5, 11 Mbps RF exposure 802.11g: 1, 2, 5.
