HP Switch Software Event Log Message Reference Guide June 2013
HP Networking Abstract This switch software guide is intended for network administrators and support personnel, and applies to the switch models listed unless otherwise noted. This guide does not provide information about upgrading or replacing switch hardware. The information in this guide is subject to change without notice.
© Copyright 2013 Hewlett-Packard Development Company, L.P. The information contained herein is subject to change without notice. All Rights Reserved. Disclaimer This document contains proprietary information, which is protected by copyright. No part of this document may be photocopied, reproduced, or translated into another language without the prior written consent of HewlettPackard.
Event Log Messages # Message Severity 0 Unknown var type fatal Description The variable type is unknown. RMON_SNMP_UNKNOWN_VAR_TYPE 1 virtual LAN enabled info The specified virtual LAN is enabled. RMON_VLAN_UP_INDIC 2 disabled info The specified virtual LAN is disabled.
Event Log Messages # Message Severity 17 Bad mask warning Description Invalid mask.
Event Log Messages # Message 45 Unable to add port to vlan , not enough hw resources on port The port was not added to the specified VLAN due to low hardware resources on the port. Unable to add port to vlan , GVRP is enabled The port was not added to the specified VLAN because GVRP is enabled.
Event Log Messages # Message 59 STP: BPDU has MAX_AGE 0 from warning port STP: BPDU has HELLO_TIME 0 from port STP:BPDU has FWD_DELAY 0 from port 60 61 Severity Bad reconfiguration request warning --------------------- info Description The switch received a BPDU packet with an invalid Max Age, Hello Time, or Forward Delay value on the specified port. Check to see if the parameter was misconfigured on the other bridge.
Event Log Messages # Message Severity 72 Slot Inactive: Module/Configuration mismatched warning — — 73 Description The module or configuration is incompatible for this slot. RMON_CHASSIS_MODULE_INCOMPAT Reserved RMON_CHASSIS_RESERVED 74 — warning Unused RMON_BUF_PIG 75 Out of buffers; miss count: warning The number of misses indicates the number of times that an attempt to allocate the specified message or packet buffer failed.
Event Log Messages # Message Severity Description 89 Unable to download Image File (using TFTP) with retries warning The image file could not be downloaded after the specified number of retries.
Event Log Messages # Message Severity 103 — — Description Reserved RMON_TCP_RESERVED5 104 — — Unused RMON_TCP_NO_CTRL_BLOCK 105 — — Unused RMON_TCP_CLOSE_EVENT 106- — 109 — 110 info telnetd service enabled Reserved RMON_TCP_RESERVED1 - 4 The telnet service has been enabled.
Event Log Messages # Message 127 TFTP: GET from info , file 128 Enable succeeded Severity info Description TFTP is trying to copy a remote file from the host IP address to the specified local file of object type CONFIG, OS, or CRASH RECORD. RMON_TFTP_GET_FILE The download TFTP capability has been successfully initialized.
Event Log Messages # Message Severity 150 Completed info Description File transfer is completed RMON_FT_XFER_COMPLETE 151 152 Aborted. No workspace left in switch DRAM. warning The file transfer was aborted because there is no space in DRAM. RMON_FT_NO_SPACE Aborted. Downloaded file invalid. warning The file being downloaded is invalid so the transfer is aborted. RMON_FT_CORRUPT_FILE 153 154 155 Aborted with Fatal Error. Hardware fault on device, Corrupt FLASH. warning Aborted.
Event Log Messages # Message Severity 177 Changing time info Description The system time has been changed. RMON_NCL_CHANGING_TIME 178 New time set info A new system time was set. RMON_NCL_NEW_TIME 179 Mgr: SME CONSOLE Session MANAGER Mode established info RMON_NCL_SESSION_EST Mgr: SME CONSOLE Session OPERATOR Mode established 180 A remote login attempt failed A console session has started either through a device connected to the console port or Telnet.
Event Log Messages # Message Severity 195 Transfer terminated due to timeout warning Received a bad 16 bit CRC on binary header warning Received a bad 32 bit CRC on binary header warm 196 197 198 199 The transfer was terminated because it timed out. RMON_XM_TR_TIMEOUT A bad 16 bit CRC packet was received on a binary header. RMON_XM_BAD_16CRC_BINARY A bad 32 bit CRC packet was received on a binary header.
Event Log Messages # Message Severity Description 213 Timeout trying to sync with remote warning The transfer timed out because the Xmodem device could not sync with the remote device. RMON_XM_TIMEOUT_TRYING_SYNC_REMOTE 214 Xmodem transfer aborted warning The XMODEM transfer was aborted. RMON_XM_ABORT 215 Unexpected character from remote 216- — warning An unexpected character was received from the remote.
Event Log Messages # Message Severity 228 Traffic filter configured in row is not active warning Traffic filter configured in row is not valid warning Traffic filter configured in row was deleted warning 229 230 The traffic filter configured in the specified row is not valid. RMON_FILTER_NOT_VALID The traffic filter configured in the specified row was deleted. RMON_FILTER_DELETED — 233 “\”public\” community deleted.
Event Log Messages # Message 245 RMON file corrupt, is warning being renamed to SNMP: RMON events file corrupt, is being renamed to event_bad. SNMP: RMON alarms file corrupt, is being renamed to alarms_bad. Either the alarms file or the events file is corrupt and was renamed to alarms_bad or event_bad, respectively. Unable to add port to warning trunk, IP lockdown is configured on port.
Event Log Messages # Message Severity Description 265 Lost communication with Mgmt Module warning A management module failed to receive heartbeats from the other management module. RMON_SYSTEM_MGMT_LOST_COMM 266 Resetting Mgmt Module info The specified management module is reset. This can occur if you perform a boot standby command or for other reasons when an individual module is rebooted.
Event Log Messages # Message Severity Description 278 Module in slot not allowed info The module in the specified slot is not supported by current configuration rules; for example, the third ESP module in an alpha chassis is not supported. Slots are lettered, starting with ‘A'.
Event Log Messages # Message Severity 298 Querier Election in process info Description The querier election is in process. RMON_IGMP_ELECTION_IN_PROC 299 300 301 This switch has been elected as info Querier RMON_IGMP_ELECTION_WON The switch has been chosen as the querier switch for IGMP. This switch was not elected as Querier info RMON_IGMP_ELECTION_LOST Other Querier detected. info The switch was not chosen as the querier switch for IGMP. Another Querier has been detected.
Event Log Messages # Message Severity 315 NULL Domain name passed for target IP warning VLAN ID out of range warning 316 Description There was no domain name given to the target IP address. RMON_IGMP_PROXY_NULL_DOMAIN_NAME The VLAN ID requested is not within the range of valid values. RMON_IGMP_PROXY_BAD_VLAN 317 BAD Target IP address warning Bad target IP address.
Event Log Messages # Message Severity 331 Port - High collision info or drop rate. See help. Description A high collision or drop rate for packets has been reported on the specified port. Refer to the help information for more details. RMON_FF_LOOP_OVER_BAND 332 Port - Excessive Broadcasts. See help. info An excessive number of broadcast packets have been received on the specified port. Refer to the help information for more details.
Event Log Messages # Message Severity 346 Port - established info Description The port is established for load balancing. RMON_LDBAL_PORT_ESTABLISHED 347 348 Port - not established warning Port - detected topology error: warning The port is not established for load balancing. RMON_LDBAL_PORT_NOT_ESTABLISHED An invalid topology was detected on a port configured for load balancing at the specified MAC address.
Event Log Messages # Message Severity 363 GVRP Protocol disabled info Description The GVRP protocol has been disabled. RMON_GVRP_DISABLE 364 info GVRP received a malformed packet. One of the following messages is displayed: • Unknown attribute Type. Received Expected 1. • Packet too small. Got . Expected . • Invalid attribute length. Got . Expected . RMON_GVRP_BAD_PKT 365 Failed to create VLAN . info Max VLANs created.
Event Log Messages # Message Severity Description 379 Port in half duplex, flow control is auto-disabled info Flow control is automatically disabled on the port because it is in half-duplex mode. RMON_PPMGR_FC_AUTODISABLE 380 Port - disabled due to warning speed mismatch. See help. There is a speed mismatch on the specified port. Refer to the help information for more details.
Event Log Messages # Message Severity Description 396 Port is moved from trunk to info The LACP trunk port has been moved to another trunk group. LACP port is moved to trunk info 397 398 399 RMON_LACP_PORT_MOVED_FROM_DYNX_TO_DYNY Port is removed from info trunk . Stack Protocol enabled The LACP trunk port has been moved to the specified trunk group.
Event Log Messages # Message Severity 412 Timed out waiting for broadcast info Description The device timed out while waiting for an SNTP broadcast. RMON_SNTP_TIMEDOUT_BROADCAST 413 Updated time by seconds info The time was updated by the specified number of seconds. RMON_SNTP_UPDATED_TIME 414 All configured servers failed info All the configured SNTP servers have failed.
Event Log Messages # Message Severity Description 427 auth-timeouts for the last sec info The specified number of authorization timeouts have occurred during this time period. RMON_AAA8021X AUTH_GENSTAT_TO 428 auth-failures for info the last sec The specified number of authorization failures has occurred during the time period.
Event Log Messages # Message Severity 445 Cannot accept switch 1600/24xx/ warning 4000/8000 into mesh Description The 1600, 4000, 8000 and Series 2400 switches cannot be part of a mesh. RMON_LDBAL_DUP_MAC_MULTI_VLAN_ERROR 446 Max hop count exceeded. Check warning your mesh topology. The maximum hop count was exceeded. Check the topology of the mesh. RMON_LDBAL_MAX_HOP_EXCEEDED 447 Port - initialized info The port was initialized for load balancing.
Event Log Messages # Message Severity 468- — 477 — 478 fatal Unable to Malloc a buf of size in Description Reserved RMON_SSL_RESERVED_1 - 10 XRRP could not allocate memory of the specified buffer size in the source code module. RMON_XRRP_MALLOC_ERROR 479 480 Duplicate IP address detected standard IP address in use, XRRP cannot take over standard The specified IP address is a duplicate.
Event Log Messages # Message 492 Rcvd pkt with version number warning , expected 493 494 495 496 497 498 499 500 501 502 503 504 505 Severity Description A packet was received with an unexpected version number. RMON_XRRP_VER_MISMATCH Rcvd pkt from rtr , warning owner , vid , no such VR A packet from the specified source router and VLAN was received with an unknown virtual router ID.
Event Log Messages # Message Severity 508 Peer router has permanent control. info User has triggered failback to router . info Infinite failback has been enabled on this router. info 509 510 Description The peer router has taken master control of the virtual router. RMON_XRRP_PEER_HAS_PERMANENT_CTRL A VR failback has been initiated on the specified router. RMON_XRRP_USER_TRIGGERED_FAILBACK A failback has been enabled so that the local router recovers master status.
Event Log Messages # Message Severity Description 525 Multiple send keys for current daytime warning Multiple key chain entries are active to transmit packets during this time period. RMON_KMS_TX_KEY_OVERLA 526 Bad reference warning Key request does not correspond to configured key chain entries. RMON_KMS_GEN_ERROR 527- — 531 — 532 warning 533 534 535 536 Port Unsupported transceiver. (SelfTest Err) Check: www.hp.com/rnd/ device_help/2_inform for more info.
Event Log Messages # Message Severity 542 system: Runtime Error Skipped: info Skips the runtime error messages that are not being used. RMON_SYSTEM_ERR_SKIP 543- — 548 — 549 Insufficient power supplies to power Slot warning Module Present info 550 Description Reserved RMON_XXX_UNUSED5 - 16 The slot is not receiving sufficient power. RMON_CHASSIS_POWER_INSUFFIENT A module is installed in the specified slot. The chassis manager sees the inserted module.
Event Log Messages # Message Severity 563 Port PD MPS Absent warning indication. Description The switch no longer detects a powered device on the port. The device may have been disconnected, powered down, or stopped functioning. RMON_POEMGR_PD_MPS_ABSENT 564 Port PD Invalid Signature indication. warning The switch has detected a non-802.3af-compliant device on the port. This message appears for all non-802.3af devices connected to the port, such as other switches and PC-NICs.
Event Log Messages # Message Severity Description 574 Slot POE usage is below configured threshold of <1-99>% warning POE usage on the specified module has a configured threshold of <1-99>%, which has decreased below the threshold value set by the “power threshold” command. This message occurs if, after the last reboot, the PoE demand on the module exceeded the power threshold and then later dropped below the threshold value.
Event Log Messages # Message Severity Description 585 VID supplied for trunked port info During web or MAC authentication, a VLAN ID has been returned for the specified trunk port. RMON_WEBMAC_AUTH_TRUNK_VID 586 VID supplied for port with VID info During web or MAC authentication, a different VLAN ID is returned for this port instead of the specified VLAN ID.
Event Log Messages # Message Severity Description 604 Unable to alloc a buf of size for fatal Multicast routing is unable to acquire memory for a flow. Router memory is oversubscribed. Reduce the number of VLANs or the number of features in use. Remedies include one or more of the following: • Reduce the number of configured VLANs by moving some VLANs to another router.
Event Log Messages # Message Severity Description 609 Pkt dropped from , (), vid info A PIM packet from the specified IP address was dropped due to one of the following causes: • No PIM interface on the VLAN • Bad packet length • Bad IP header length • Bad IP total length RMON_PIM_PKT_DROPPED 610 Pkt rcvd with a cksum error from info A packet having a checksum error was received from the specified IP address.
Event Log Messages # Message Severity 617 pkt, src IP info vid (not a nbr) Description A PIM packet arrived from another router for which no neighbor was found. May indicate a misconfiguration between the sending and receiving router. May also occur if a connected router is disconnected, then reconnected.
Event Log Messages # Message Severity Description 627 Unable to allocate table fatal The router was not able to create some tables PIM-DM uses. Indicates that the router is low on memory resources. Remedies include one or more of the following: • Reduce the number of configured VLANs by moving some VLANs to another router. • Free up system resources by disabling another feature, such as one of the spanning-tree protocols or either the RIP or the OSPF routing protocol.
Event Log Messages # Message Severity Description 639 SCP error: info An error was detected in the SCP session with the device at the specified IP address. RMON_SCP_ERR 640 SFTP error: warning An error was detected in the SFTP session with the device at the specified IP address. RMON_SFTP_ERR 641 , session aborted warning The SSH session was aborted. RMON_SSH_ERR 642 SSH server enabled in IPv4 mode info The SSH server is enabled in IPv4 mode.
Event Log Messages # Message Severity 655 : Unable to create VLAN. fatal : VLAN is created. info 656 Description A VLAN configuration on a downlink port has failed. RMON_HPESP_CONFIG_ERROR A VLAN has been successfully configured and a downlink port is assigned as a tag member. RMON_HPESP_VLAN_CREATED 657 : Application initialization failed. fatal Module initialization has failed for one of the following reasons: • HPESP version is not supported.
Event Log Messages # Message Severity 670 fatal Description A fatal error has occurred while updating the software license. RMON_HPESP_LICENSE_FATAL 671 info The license update is successful. RMON_HPESP_LICENSE_INFO 672 warning An unexpected event occurred when accessing module application data. RMON_HPESP_APPLDATA_ERROR 673 flash write aborted; info write already in progress.
Event Log Messages # Message Severity 687 info Description An upgrade to boot ROM was successful. RMON_BOOTROM_UPGRADE_PASSED 688 LLDP - enabled info The Link-Layer Discovery Protocol (LLDP) is globally enabled. RMON_LLDP_ENABLED 689 LLDP - disabled info LLDP is disabled. LLDP traffic will not be received on the switch.
Event Log Messages # Message 701 Could not create ACL entry. client info mac , port RMON_IDM_CREATE_ACL_ERROR Could not add ACL, client mac , port , At max per-port ACL quantity. The ACL, configured on the specified client and port, could not be added because the threshold number of per-port ACLs supported in internal ACL storage has been reached.
Event Log Messages # Message Severity Description 714 ACE limit per port exceeded. client , port info The maximum number of configured entries has been exceeded on ACLs assigned to the specified port and device. Exceeded counter per slot limit. client , port info 715 716 717 719 720 721 722 RMON_IDM_QTY_RULE_PER_PORT_LIMIT_ERROR The maximum number of supported packet counters has been exceeded on ACLs assigned to the specified port and device.
Event Log Messages # Message Severity 734 Ports Downloading info Description A software download on the specified port(s) is in progress. RMON_CHASSIS_FIX_SLOT_DOWNLOADING 735 736 Ports Download Complete info Ports Download Failed warning The software download on the specified port(s) was successful. RMON_CHASSIS_FIX_SLOT_DOWNLOAD_COMPLETE An attempted software download on the specified port(s) was not successful.
Event Log Messages # Message Severity Description 753 Static RP configuration failure: , warning The configuration of a static RP for the specified multicast group has failed on the interface. RMON_PIM_BSR_STATIC_RP_CONFIG_FAIL 754 755 Malformed Candidate-RP adv recvd from warning Failed flow remove: vid info The switch failed to delete a flow programmed into hardware.
Event Log Messages # Message Severity Description 779 Vrid , Vid recd pkt with invalid auth type warning Indicates the VR has received a VRRP packet with an authentication type set to a value other than the 0, 1, or 2 (allowed by RFC 3768) and has dropped the packet.
Event Log Messages # Message Severity 792 Vrid on Vid lost info backup IP ctrl Description The specified VR has been preempted by either the owner or a higher-priority master. RMON_VRRP_VR_LOST_BACKUP_IP_CTRL 793 Vrid , Vid IP addr warning is duplicated on network The virtual IP address owned by the VR on the specified VLAN is duplicated on the network.
Event Log Messages # Message Severity Description 810 installed, key info A software package has been installed with a license key on the switch. RMON_LICENSING_INSTALL 811 uninstalled, key info A software package and its license key have been removed from the switch. RMON_LICENSING_UNINSTALL 812 Licensing error () occurred, if this problem continues please contact support.
Event Log Messages # Message Severity Description 826 Port released from VLAN info The specified port has been released from the specified VLAN configuration. This is most likely due to another application configuring the port for temporary untagged membership in some other VLAN, the port being configured in a trunk, or the VLAN being deleted.
Event Log Messages # Message Severity Description 843 bpdu loss - port moved to inconsistent state for > info Port is changed to inconsistent state for the indicated CIST or MSTI number.
Event Log Messages # Message 858 : Client address warning not equal to source MAC detected on port 859 : Ceasing client address mismatch logs for Severity warning Description The DHCP agent detected that a source MAC address in a client packet does not match the MAC address in the Change Address (chaddr) field of the packet. The packet was dropped.
Event Log Messages # Message Severity Description 869 Ceasing removed lease logs for warning Removed lease logs will not be logged for the specified duration. The dsnooping table is full. RMON_DSNOOP_TABLE_FULL_REM_LEASE_SUSP 870 871 Drop request from for because the address is assigned to another client warning The client is requesting an IP address that is already in use by a different client in the same VLAN.
Event Log Messages # Message Severity 892- — 896 — 897 The existing config requires changing default for parameter: info LP Manager s has disabled port for seconds info LP Manager has disabled port warning 898 899 900 901 902 903 904 905 906 907 908 Description Reserved RMON_SFLOW_UNUSED_1 - 5 You must change the default for the parameter indicated, for this configuration.
Event Log Messages # Message Severity 930 Slot Link failure: Fabric warning has faulty link to Slot Description A fault on a line card prevents it from connecting to fabric. The error may be recoverable. RMON_CHASSIS_FABRIC_FAIL_LC 931 932 933 Fabric failure: link error between warning Fabric and Slot The fabric blade has a faulty link to a slot in the chassis. The error may be recoverable.
Event Log Messages # Message 946 Filter-rule parsing error. “ip” warning keyword or protocol number, listindex rule-index 947 948 949 950 951 952 953 954 Severity Filter-rule parsing error. “from” keyword, list-index rule-index warning Filter-rule parsing error “any” keyword, list-index rule-index warning Filter-rule parsing error. “to” keyword, list-index rule-index warning Filter-rule parsing error.
Event Log Messages # Message 958 Profile apply error, untagged vlan warning conflict, MAC port profile (profilenum> 959 960 961 962 963 964 965 966 967 968 969 970 Severity Profile apply error, tagged vlan warning conflict, MAC , port profile Profile apply error, priority regen warning conflict, MAC port profile Profile apply error, max ingress warning bandwidth conflict, MAC port
Event Log Messages # Message Severity 971 DHCP address not added on Vlan: warning . Subnet already exists. Description The DHCPv6 address was not added to the indicated VLAN as that VLAN already exists.
Event Log Messages # Message Severity 984 wrong ver# in info packet from server Description The wrong version number was in the packet received from the indicated server. RMON_TACACS_VER_MISMATCH_PKT 985 wrong seq# info (expected ) in packet from server An incorrect packet sequence number was received from the specified server.
Event Log Messages # Message Severity 2000 Unable to alloc a buf of size for %s fatal 2001 Unable to alloc a msg buffer for %s fatal Description MTM could not allocate memory. RMON_MTM_MALLOC_ERROR A message buffer could not be allocated. RMON_MTM_NO_MSG_BUF 2002 Unexpected state/event / warn in %s statematch 2003 Rcvd unkwn addr fmly in info pkt. MTM received an event type in a state that was not expected.
Event Log Messages # Message Severity 2401 client warning RADIUS-assigned priority-Regen validation error, MAC port 2402 client warning untagged VLAN-id arbitration error, MAC port 2403 client warning tagged VLANs arbitration error, MAC port 2404 client priority regeneration (aka COS) arbitration error, MAC port
Event Log Messages # Message 2506 Filename too long: Severity warning Description The file name is too long. RMON_AUTORUN_EVT_FILENAME_TOO_LONG 2507 Cannot create file: warning The file can’t be created. RMON_AUTORUN_EVT_CANNOT_CREATE_FILE 2508 Cannot delete file: warning The file can’t be deleted. RMON_AUTORUN_EVT_CANNOT_DELETE_FILE 2509 Cannot write to file: warning Autorun cannot write to the file.
Event Log Messages # Message Severity 2551 Failed to obtain co-processor OS fatal image location Description The download task was unable to provide the slave OS image location. RMON_CHASSIS_LOAD_REQ_OS_FAILED 2552 Loading of co-processor OS image in progress info Chassis manager is getting the slave OS from flash, decompressing it, and copying the OS into the slave area of RAM.
Event Log Messages # Message 2562 Port : PSE detected. Port PoE disabled. Severity Description warning PSE = Power Sourcing Equipment. A PoE+ port is linked to a PoE port (switch-to-switch link). The port detects that the connected port is capable of providing PoE, so PoE delivery for that port is disabled. It appears as an error even though it is expected behavior for switch to switch links. If this occurs on a port that was connected to a PoE device, it might indicate a port PoE problem.
Event Log Messages # Message Severity 2613 Inconsistent config for the standard subsystem ; at least one loopback interface must exist on the System before configuring 2614 Config attempt failed info Description A loopback interface must be configured on the system. RMON_CONFIG_IPV6_ONLY_ERR A configuration attempt failed. RMON_CONFIG_ATTEMPT_FAILED 2615 SVLANS cannot be added to any info MST instance in qinq mixed vlan mode. Inconsistent configurations have been deleted.
Event Log Messages # Message Severity 2672 Port - Excessive link warning state transitions. Description There were too many link state transitions (link up and link down states) and the port is disabled. RMON_FF_LINKFLAP 2673 port - Port disabled by Fault-finder fatal 2674 port - Administrator fatal action required to re-enable 2681 Workaround nic82566dm occurred. See www.procurve.com/ device_help/nic_update for more details. The port indicated has been disabled.
Event Log Messages # Message Severity 2689 Ceasing cleared dhcp-snooping warn event statistics 2690 Drop request from warn for because the maxbinding limit has reached on the port . Description The clearing of DHCP-snooping event log statistics has stopped. RMON_DSNOOP_CLEAR_STATS_SUSP Packets are being dropped because the max binding limit has been reached for the specified port.
Event Log Messages # Message Severity 2750 Blade LEDs configured info to be OFF Description The module’s LED’s are configured to be off in savepower mode, in an operational chassis. RMON_SAVEPOWER_LEDOFF_ENABLED 2751 Blade LEDs configured info to be ON A module’s LED’s are configured to be on in normal mode, in an operational chassis.
Event Log Messages # Message 2768 Port PoE power dropped. Exceeded physical classification for a PoE Type1 device. Severity Description warn LLDP is disabled at runtime and the PD was draining PoE+ power negotiated through LLDP. RMON_POE_RESTRICT_PWR_FOR_TYPE1_PD 2769 Ext Power Supply measured out of spec or is faulty. Please change or contact An EPS is plugged in and the software reads invalid isrc value.
Event Log Messages # Message Severity Description 2786 Internal power supply : System exceeded current threshold, caused shutdown. fatal The power supply’s output power has exceeded a threshold. Power supply has shut down. 2787 Internal power supply : System exceeded current threshold, caused shutdown. fatal 2788 Internal power supply : System exceeded voltage threshold, caused shutdown.
Event Log Messages # Message Severity 2798 Internal power supply has lost main POE power. 2799 Internal power supply has lost auxiliary POE power. fatal 2801 Invalid HELLO packet from on interface: Invalid Hello Interval none The power supply’s main POE source has lost power. RMON_IPS_POE_MAIN_PWR_LOSS_FAULT The power supply’s auxiliary POE source has lost power. RMON_IPS_POE_AUX_PWR_LOSS_FAULT Hello interval mismatch in Hello packet.
Event Log Messages # Message Severity 2811 Discarding packet from none on interface at state 2812 Invalid router priority configuration on interface none 2813 Too many neighbors for HELLO packet on interface none 2814 Invalid event at state none Description A packet is dropped. RMON_OSPF3_ADJCHG_DETAIL_WRONG_PACKET There is an invalid router priority configuration.
Event Log Messages # Message Severity Description 2828 Discarding packet on interface: Received frame size is less than OSPFv3 header size none The received frame size is less than the OSFv3 packet header size.
Event Log Messages # Message Severity Description 2840 Invalid Grace LSA on interface : Invalid Restart Reason TLV length none The grace LSA is invalid because the TLV length is incorrect. 2841 Invalid Grace LSA on interface: Restart Reason TLV missing none 2842 Invalid Grace LSA on interface: Unknown restart reason none 2843 Failed to find local interface for nexthop none 2844 Restart will not happen.
Event Log Messages # Message Severity Description 3008 Stack bndry mbr port info other stack id RMON_PRO_STACK_BOUNDARY_FOUND The stack cable is looped back to the same switch. 3009 MAX stack switches exits cannot warn add switch If this switch is added, the maximum number of switches allowed in the stack will be exceeded.
Event Log Messages # Message Severity Description 3056 BGP route count falls below maximum allowed prefix limit routes. info The BGP route count has fallen below the maximum allowed. 3057 BGP router-ID changed. info RMON_BGP_FALLBELOW_MAXPREFIX The BGP router ID has changed. RMON_BGP_ROUTERID_CHANGED 3058 Router-id on device changed, this affects BGP. info 3071 : Peer configured, AS info 3072 : Peer up info A router ID changed, affecting BGP.
Event Log Messages # Message Severity 3085 : Peer remote-AS changed to info 3086 : Peer local-AS changed to info 3087 : Peer source-address changed to info Description The AS of the remote peer is changed. RMON_BGP_PEER_REMOTEAS_CHANGED The AS of the local peer is changed. RMON_BGP_PEER_LOCALAS_CHANGED The BGP peer source address has changed to the indicated address.
Event Log Messages # Message Severity Description 3135 Discarding invalid DD packet on event deter- An invalid DD packet was discarded on the specified port. interface : mines RMON_OSPF_ADJCHG_DETAIL_DD_PACKET_PROCESSING priority 3136 Discarding invalid LSR packet on event deter- An invalid LSR packet was discarded on the specified port.
Event Log Messages # Message Severity Description 3149 Invalid Grace LSA on interface : Restart Reason TLV missing event deter- The TLV is missing so the Grace LSA is invalid. mines RMON_OSPF_RESTART_GRACE_LSA_RESTART_REASON_TLV priority 3150 Invalid Grace LSA on interface : Invalid interface Addr TLV length event deter- The interface address length is incorrect so the Grace LSA is mines invalid.
Event Log Messages # Message Severity 3163 UFD - Link to Monitor Up and LtD info auto-enabled 3164 Track ID : LACP conflict! warn If dynamic LACP trunks were monitored with the lacp-key between <1-key num> or . 3166 Attempting unplanned restart.
Event Log Messages # Message Severity 3207 client max dynamic warn port-access settings arbitration error, MAC port 3210 client max dynamic port- info access settings arbitration error, MAC port 3211 Illegal combination of attributes info and in received RADIUS packet on port 3212 Conflict between Configuration and attribute received in RADIUS packet on port info Description There is a
Event Log Messages # Message 3232 Switch role is Primary Severity Description info A keep-alive packet was received. This switch is selected as Primary. Traffic continues to be forwarded on DT ports. RMON_DT_SWITCH_ROLE_PRIMARY 3233 Switch role is Secondary, disabling all DT trunks info A keep-alive packet was received. This switch is selected as Secondary; the DT ports are disabled.
Event Log Messages # Message 3261 Crash info: Severity warn Description Indicates the reason for the crash. RMON_PRO_STACK_BOOT_CRASH_RECORD1 3262 Lost Communication with Member info 3263 Resetting member info Communication is lost with a stack member. RMON_PRO_STACK_LOST_COMM A stack member is resetting. RMON_PRO_STACK_RESET 3264 Failover occurred info A failover occurred.
Event Log Messages # Message 3305 ISC port is deleted from keepalive VLAN Severity Description info ISC port will be deleted from a VLAN when the VLAN is configured as a keepalive VLAN. RMON_DT_ISC_DELETED_FROM_VLAN 3306 Trunk type mismatch detected on warn The hello packet indicates that the peer trunk is a different type. RMON_DT_TRUNK_TYPE_MISMATCH 3307 Keepalive mis-configuration detected.
Event Log Messages # Message Severity 3362 Hostname must contain only info letters, numbers, and hyphens, and must not start with a hyphen or end with a hyphen. Description RFC for protocols mandates that component hostname labels may contain only the ASCII letters “a” through “z” (in a case-sensitive manner), the digits “0” through “9”, and the hyphen (-). RFC 1123 permits hostname labels to start with digits, but not hyphens. No other symbols, punctuation characters, or blank spaces are permitted.
Event Log Messages # Message Severity 3375 <%s> does not have a valid entry fatal Description The hash of the UUID grant date chassis MAC does not match with the cert entry. RMON_HPESP_CERT_INVALID_ENTRY 3376 A new APP request has been received info This is a log message about a received request on the HPesp Sys connection. RMON_HPESP_CERT_CSR_RECV 3385 Unknown users from warn are locked out for seconds. An unknown user plus the IP address is locked out.
Event Log Messages # Message Severity 3412 CA-signed certificate info installed on Trust Anchor. Profile for usage . 3413 Local Certificate removed. info 3414 Certificate is invalid. The chain exceeds 5 certificates. warn Description The specified CA-signed certificate has been installed on the Trust Anchor with the indicated profile and usage. RMON_CRYPTO_CERTMGR_CA_CERT_INSTALLED The specified local certificate has been removed.
Event Log Messages # Message 3516 Service deregistered Severity info Description The service advertised has been deregistered. RMON_SLP_SVC_DEREG_SUCCESS 3517 Service deregister failed info 3518 Listening on IP port for SLP request info 3519 Stopped listening on IP port for SLP requests info 3520 Socket error fatal There has been a failure in deregistering the advertised service.
Event Log Messages # Message Severity Description 3571 modify authorization table failed debug uuid , service , attribute RMON_ECM_MODIFY_AUTHR_FAIL 3572 ssl handshake failed. peer ip , service RMON_ECM_SSL_HANDSHAKE_FAIL debug Modifying an entry from the authorization table failed. The SSL handshake failed for a connection. 3573 saving author file to flash failed.
Event Log Messages # Message 3625 DHCP server stopped Severity info Description The DHCP server is stopped. RMON_HPESP_IP_DHCPS_STOPPED 3626 DHCP server restart failed info The DHCP server restart failed. RMON_HPESP_IP_DHCPS_RESTART_FAILED 3627 DHCP server IP range set to 3628 DHCP server lease time set to seconds info 3629 Config inconsistency detected. Some records may have been deleted. info The DHCP server IP address range has changed.
Event Log Messages # Message Severity 3784 Invalid domain name provided by warning DHCP Server on Primary VLAN 3785 Invalid DNS server address provided by DHCP Server on Primary VLAN warning 3801 Mgmt module Nonstop switching disabled because of SW version mismatch. Warm standby enabled. warn An invalid domain name was provided by the DHCP server. RMON_DHCP_INVALID_DNS_SUFFIX The DNS server address provided by the DHCP server on the primary VLAN is invalid.
Event Log Messages # Message Severity Description 4057 An over-current has been detected on external power supply. warn Over current has been detected on the external power supply. 4058 An overtemperature has been detected on external power supply. warn 4059 Main power rail on external power supply has failed. warn 4060 Internal power supply failure detected. warn 4061 External power supply ready info RMON_PPS_OVER_CURRENT_DET The external power supply is over temperature.
Event Log Messages # Message Severity Description unk Configuration removed for module in slot . info A slot has been removed with the no module command and the entire configuration for the module has been deleted.
Event Log Messages 94
Technology for better business outcomes To learn more, visit www.hp.com/networking © Copyright 2013 Hewlett-Packard Development Company, L.P. The information contained herein is subject to change without notice. The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty. HP will not be liable for technical or editorial errors or omissions contained herein.
