HP A6600 SSL VPN Card Manual-6P102

ManualsBrandsHP ManualsComputer AccessoriesHP 7100/7200 IPsec dl Module

Manual Version: 6P102-20111130 BOM:

3123A0F6

Part number: 5998-2240

HP A6600 SSL VPN Module

1 Appearance

The silkscreen SPE-SSL-200 is printed at the upper right corner of the front panel, and it identifies the

module.

Figure 1 Appearance of the SPE-SSL-200

2 Specifications

The SPE-SSL-200 module provides one console port, one CF card slot, and two USB interfaces.

Figure 2 Front panel of the SPE-SSL-200

(1) CF card eject button (2)

CF card

slot

(CF CARD)

(3) CF LED (CF)

(4) Console port (CONSOLE) (5) USB interface 1 (reserved) (6) USB interface 2 (reserved)

(7) USB interface 2 LED (USB) (8) Ejector lever

(9) Captive screw

Table 1 Description of the LEDs on the SPE-SSL-200

Silkscreen Color Status

Descri

tion

CF Green

Off No CF card is present or the CF card is not recognizable.

On A CF card is in position and has passed the power-on self test.

Blinking

The system is accessing the CF card. In this state, do not

remove the CF card.

Summary of content (6 pages)

PAGE 1
Manual Version: 6P102-20111130 BOM: 3123A0F6 Part number: 5998-2240 HP A6600 SSL VPN Module 1 Appearance The silkscreen SPE-SSL-200 is printed at the upper right corner of the front panel, and it identifies the module. Figure 1 Appearance of the SPE-SSL-200 2 Specifications The SPE-SSL-200 module provides one console port, one CF card slot, and two USB interfaces.
PAGE 2
Manual Version: 6P102-20111130 BOM: 3123A0F6 Part number: 5998-2240 Table 2 SPE-SSL-200 specifications Item Interface Specification One console port Two USB interfaces (reserved) Interface transmission speed Console port: 9600 bps to 115200 bps (default: 9600 bps) Cable and maximum transmission distance Console port: Asynchronous serial cable with maximum transmission distance of 15 m (49.21 ft) • One CF card slot. By default, no CF card is configured.
PAGE 3
Manual Version: 6P102-20111130 BOM: 3123A0F6 Part number: 5998-2240 Figure 3 Insert the SPE-SSL-200 (1) Push the module into the slot along the guide rails until the positioning hole of the module is seated onto the positioning pin on the backplane. (2) Push the ejector levers inward to lock the module in place. 3.2 Removing the SPE-SSL-200 1. Loosen the captive screws on the module with a Philips screwdriver until all spring pressure is released. 2.
PAGE 4
Manual Version: 6P102-20111130 BOM: 3123A0F6 Part number: 5998-2240 On your PC, run a terminal emulation program, such as Terminal of Windows 3.X and HyperTerminal of Windows 9X and Windows XP. Set the terminal communication parameters as follows: • Baud rate—9600 bps • Data bits—8 • Parity—None • Stop bit—1 • Flow control—None NOTE: The required values of the terminal communication parameters depend on the device model. 3.
PAGE 5
Manual Version: 6P102-20111130 BOM: 3123A0F6 Part number: 5998-2240 Figure 5 SSL VPN management login page CAUTION: • The PC in Figure 4 is for basic device configuration. The Web management terminal can be the PC or some other hosts. • HP recommends that you change the login password after you log in for the first time. 5 Upgrading the SPE-SSL-200 The SPE-SSL-200 supports software upgrade through the console port on the module and the service port of the router.
PAGE 6
Manual Version: 6P102-20111130 BOM: 3123A0F6 Part number: 5998-2240 6 Obtaining documentation For module installation, see the HP A6604/A6608 Routers Installation Guide or HP A6616 Router Installation Guide. For software upgrade, see the HP Security Modules Software Upgrade Guide. To find related documents, browse to the Manuals page of the HP Business Support Center website: http://www.hp.com/support/manuals © Copyright 2011 Hewlett-Packard Development Company, L.P.