R3204P16-HP Load Balancing Module Network Management Configuration Guide-6PW101

ManualsBrandsHP ManualsComputer AccessoriesHP 7100/7200 IPsec dl Module

141

142

143

144

145

146

147

148

149

150

Table Of Contents

Title page
Contents
Interface management configuration
- Interface overview
  - Physical interfaces
  - Logical interfaces
- Managing interfaces in the web
- Managing interfaces at the CLI
IP addressing configuration
- IP addressing overview
- Configuring IP addresses
  - Assigning an IP address for an interface
  - IP addressing configuration example
    - Network requirements
    - Configuration procedure
- Displaying and maintaining IP addressing
MAC address table configuration
- Overview
- Configuring a MAC address table in the web
- Configuring the MAC address table at the CLI
Layer 2 forwarding configuration
- Layer 2 forwarding overview
- Configuring general Layer 2 forwarding
  - Configuration procedure
  - Displaying and maintaining general Layer 2 forwarding
- Configuring inline Layer 2 forwarding
  - Configuration procedure
  - Displaying and maintaining inline Layer 2 forwarding
- Configuring inter-VLAN Layer 2 forwarding
  - Configuration procedure
  - Displaying and maintaining inter-VLAN Layer 2 forwarding
- Forward-type inline Layer 2 forwarding configuration example
  - Network requirements
  - Configuration procedure
- Blackhole-type inline Layer 2 forwarding configuration example
  - Network requirements
  - Configuration Procedure
- Inter-VLAN Layer 2 forwarding configuration example
  - Network requirements
  - Configuration Procedure
VLAN configuration
- Introduction to VLAN
- Configuring a VLAN in the web
- Configuring a VLAN at the CLI
  - Configuring VLAN
  - Configuring isolate-user-VLAN
ARP configuration
- ARP overview
- Configuring ARP
- Displaying and maintaining ARP
- ARP configuration example
  - Network requirements
  - Configuration procedure
Gratuitous ARP configuration
- Introduction to gratuitous ARP
  - Enabling learning of gratuitous ARP packets
  - Configuring periodic sending of gratuitous ARP packets
- Configuring gratuitous ARP
Proxy ARP configuration
- Proxy ARP overview
  - Proxy ARP
  - Local proxy ARP
- Enabling proxy ARP
- Displaying and maintaining proxy ARP
- Proxy ARP configuration examples
Layer 3 forwarding configuration
- Layer 3 forwarding overview
  - Layer 3 subinterface forwarding
  - Inter-VLAN Layer 3 forwarding
- Configuring Layer 3 subinterface forwarding
  - Configuring Layer 3 subinterface forwarding
    - Configure the ports of the switch
    - Configure the LB module
  - Displaying and maintaining Layer 3 subinterface forwarding
- Configuring inter-VLAN Layer 3 forwarding
  - Configuring inter-VLAN Layer 3 forwarding
    - Configure the ports of the switch
    - Configure the LB module
  - Displaying and maintaining inter-VLAN Layer 3 forwarding
- Layer 3 subinterface forwarding configuration example
  - Network requirements
  - Configuration procedure
- Inter-VLAN Layer 3 forwarding configuration example
  - Network requirements
  - Configuration procedure
NAT configuration
- Overview
- Configuring a NAT policy in the web interface
- Configuring NAT in the CLIs
- Configuration guidelines
ALG configuration
- ALG overview
- Enabling ALG
- ALG configuration examples
Static route configuration
- Configuring static route in the web interface
  - Static route configuration example
- Configuring static route in the CLI
RIP configuration
- Configuration prerequisites
- Configuration overview
- Configuring RIP globally
- Configuring interface RIP
- RIP configuration example
- Configuration guidelines
OSPF configuration
- Configuration prerequisites
- Configuration overview
- Configuring OSPF globally
- Configuring OSPF areas
- Configuring OSPF interfaces
- Displaying OSPF interface information
- Displaying OSPF neighbor information
- OSPF configuration example
- Configuration guidelines
BGP configuration
- Configuration prerequisites
- Configuration overview
- Configuring BGP globally
- Configuring BGP peer
- Displaying BGP peer information
- BGP Configuration example
Policy-based routing configuration
- Configuring PBR
- Creating a policy
- Applying a policy
- Configuration guidelines
Route displaying
- Displaying routing information in the web interface
- Displaying routing information in the CLI
DNS configuration
- Overview
- Configuring DNS on the web interface
- Configuring DNS in the CLIs
- Troubleshooting IPv4 DNS configuration
  - Symptom
  - Solution
Support and other resources
- Contacting HP
  - Subscription service
- Related information
  - Documents
  - Websites
- Conventions
Index

143

Select Network > BGP from the navigation tree of Device B, and then click Show Peer in the Show

Information field. BGP connections are established from Device B to other devices, as shown in Figure

Figure 103 BGP configuration result